Search Documents

By Kym L. Morton

Ground water and associated pore pressure represent elements which can have a negative impact on surface mining and slope stability. Ground water flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data was available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

By Z. Szczepanik, D. Milne, K. Kostakis

Abstract This paper presents the results of a series of creep tests performed on a total of nine samples of Lac du Bonnet granite from the Underground Research Laboratory near Pinawa, Canada. Each of the nine samples were subjected to stresses in excess of 80% of the average uniaxial compressive strength of the granite and were maintained at that level of constant loading for periods of time ranging between a few minutes and several months. Acoustic emission was recorded in order to monitor the development and accumulation of brittle microfracture damage in the samples throughout the long-term loading. According to previously published theoretical predictions and field results, as well as similar experimental results of creep tests in granite, samples should fail when loaded to 70% of their UCS for an extended period of time. Six of the samples did not fail when subjected to stresses in excess of 80% of their UCS over periods of several months and were subsequently subjected to uniaxial compression to failure. The average strength of the samples that had previously been subjected to long-term loading were comparable to the average published strength of this rock. Three of the nine samples had increased end confinement and these three samples failed under long term loading. Résumé Cet article présente les résultats d'une série d'essais de fluage de roche exécutés sur neuf échantillons de granite de Lac du Bonnet, du laboratoire souterrain de recherches près de Pinawa, Canada. Chacun des neuf échantillons a été alors soumis aux charges au-dessus de 80% de la résistance à la UCS moyenne du granit et a été maintenu à ce niveau du chargement constant pendant des périodes s'étendant entre quelques minutes et plusieurs mois. L'émission acoustique a été enregistrée pendant les essais afin d'obtenir des indications des dommages pendant le chargement à long terme. Selon des résultats théoriques précédemment édités et les résultats expérimentaux semblables des essais à long terme en granite, échantillons devrait échouer si chargé à 70% de leur UCS pendant une période prolongée. Six des échantillons n'ont pas cassé quant ils ont été soumis aux charges au-dessus de 80% de leur UCS et ont été plus tard soumis à la compression uniaxiale à la rupture. La force moyenne des échantillons qui avaient été précédemment soumis au chargement à long terme étaient comparable à la force éditée moyenne de cette roche. Trois des neuf échantillons avaient augmenté le confinement de fin et ces trois échantillons ont cassé sous le chargement à long terme. Zusammenfassung Dieser Artikel beschreibt die Resultate von Kriechversuchen, die an neun Proben aus dem Lac du Bonnet Granit des "Underground Research Laboratory" bei Pinawa in Kanada durchgeführt wurden. Jede der neun Proben wurde Drücken unterworfen, die mehr als 80% der einaxialen Druckfestigkeit des Granites entsprechen. Diese Drücke wurden für verschiedene Zeitspannen von wenigen Minuten bis zu einigen Monaten auf einem konstanten Niveau gehalten. Während der gesamten Langzeitbelastung wurden akustische Emissionen aufgezeichnet, um die Entwicklung und gesamthafte Beschädigung der Proben durch Sprödbruch aufzuzeichnen. Entsprechend bisher veröffentlichter theoretischer Vorhersagen, Feldversuchen und auch experimentellen Resultaten von Kriechversuchen an Granitproben wäre ein Versagen der Proben zu erwarten gewesen, wenn sie über längere Zeit einer Last von 70% ihrer einaxialen Druckfestigkeit unterworfen werden. Wider Erwarten trat bei sechs der Proben kein Versagen ein, als sie mit über 80% ihrer einaxialen Druckfestigkeit über mehrere Monate belastet wurden; daher wurden sie im Anschluss bei einaxialer Kompression zum Versagen gebracht. Die mittleren Festigkeiten der im Langzeittest verwendeten Proben sind vergleichbar mit den normalerweise für diesen Gesteinstyp angegebenen Festigkeiten. Drei der neun Proben versagten unter der Langzeitbelastung; diese drei Proben hatten eine erhöhte Endflächenreibung.

Jan 1, 2003

Dr H. J. van Eck (Honorary Life Member): "Mr President, I regard it as a signal honour that I was invited to address the South African Institute of Mining and Metallurgy on its 75th Anniversary. I also wish to add my congratulations and good wishes to the many you have already received on this memorable occasion. Seventy-five years is indeed a good age and the achievements of your Institute certainly justify this special celebration. South Africa owes her present prosperity largely to the technological ability and determination of her own people. Members of the Institute contributed in large measure to this great development of our country and through the years have upheld their high reputation for scientific integrity, dynamic enterprise and dedicated service. It was their knowledge which provided the key to unlocking the mineral wealth which lay dormant for countless ages. The history of world mining dates back many centuries. We know of the mercury mines of Spain, the tin mines of Cornwall and the zinc mines of Poland, but it was not until colonization of the western hemisphere started in about 1500 that mining of any consequence began in North America. It is true that the peoples of South America and Mexico had accumulated wealth out of gold and silver, but industrialized mining was not a feature of these agrarian cultures. The mining wealth that eventually developed in North America was based on advances in the technology of processing minerals and served as an incentive to people in other new countries. Big mines were opened elsewhere in the world. From Canada, Mexico, Venezuela, Brazil, Peru, Chile, Bolivia, Rhodesia, Australia, Burma and India, to name but a few, there has been a steadily increasing production of an expanding range of minerals and metals. By the middle of the 20th century the trend was to increase the production and use of such comparatively uncommon metals as cobalt, nickel, titanium, and others, and a great mining rush started to search for, and develop, the deposits of uranium, and related radio-active minerals. It is worth pausing a few minutes to reflect that most of early mining was based on the recovery of virgin metals like gold and silver or easily treated high grade ores of copper, tin and zinc. Today, much of this type of mining would be regarded as picking the eyes out of the mine. With the development of improved ore separating, ore concentration and recovery processes, we developed into bulk mining and bulk treatment and in South Africa we have some very big mines, also outside the gold mining industry at Phalaborwa, for instance. Mining techniques are applied which compare with the best in the world. These large mines could only develop because of the perfection of new concentrating techniques and, of course, because of the development of markets. We have mentioned nickel and cobalt. These names were given to those mischievous mining sprites called nickels and kobolds to whom the suspicious miners ascribed their inability to smelt copper from copper nickel or arsenious copper ores. In South Africa, the presence of minerals was known to the modern Western world as far back as 1497 when Vasco da Gama found the native 'strandlopers' at the St. Helena Bay wearing copper rings. In 1669, after the British East India Company had formed their settlement, they employed miners and assayers in prospecting for minerals and in 1685 found traces of copper in the copper mountain of Namaqualand where some 170 years later a rich deposit of copper was to be opened up. This deposit also had a chequered

By M. F. Dawson, S. B. Davis

SYNOPSIS This paper describes the size reduction of limestone smaller than 1 mm by attrition grinding, using quartz (1 to 3 mm) as the grinding medium in a laboratory rig. The ore and grinding medium were closely sized fractions, and the particle size of the grinding medium was at least three sizes larger than that of the ore. Batch tests showed that the size reduction of the feed followed two first-order rate processes: one for an apparently fast-breaking ore fraction, and a slower one for most of the ore (86 per cent). The production of fines (material smaller than 10 µm) followed a zero-order rate equation. Continuous runs showed that the process could be modelled as a perfectly mixed system provided that the discharge screen did not selectively retain coarser particles of ore. The ratio of medium to ore (both by mass and by volume) was found to have a significant effect, the most energy¬efficient grinding occurring at ratios between 1 and 2. The solids content of the slurry also had a significant effect, the greatest efficiency being obtained at 50 to 65 per cent solids (by mass). Within these energy-efficient ranges of medium-to-ore and solids content, the lower values resulted in maximum feed breakage and the higher values in maximum fines production. The most important factor in the breakage of feed was the difference in the particle size of the grinding medium and the ore; the amount of ore broken out of the feed size for a given energy input was found to increase linearly with the difference between the size of the grinding medium and that of the ore up to 2 mm. The production of fines increased similarly, but only up to a difference of about 1,2 mm, when it levelled off at about 5 kg/kW ? h. The mechanism proposed for attritioning is mainly the abrasion of 1 µm planes of limestone along the crystal axes, with some fracturing along existing lines of weakness. The energy consumption of nearly 200 kW ? h per ton of product smaller than 10 µm appears to be higher than that in other types of milling. It is concluded that the value of attrition milling lies in its selectivity; in this work, only the softer limestone and virtually none of the hard quartz grinding medium was comminuted.

Jan 1, 1989

By E. E. Almási, G. Mucsi, G. Rákhely, Á. Rácz, B. Csőke, Zs. Pap, K. Bohács, N. Halyag

Wet stirred media milling is a widely applied grinding process in the field of mineral processing to produce <10 μm ground materials. In this paper, the results of wet stirred media milling of different Ti, Fe and Cu-oxide and phosphate minerals are presented. During the experimental work, grinding of ilmenite, vivianite, hematite and cuprite was carried out in a continuous operation wet stirred media mill. During the experiments, the particle size distribution and specific surface area of the ground materials were determined after a certain grinding time, as well as measuring the specific grinding energy, thereby determining the grinding kinetics of the different minerals. The measurement results showed the differences and similarities in the grindability of the individual minerals. Nano particulate vivianite, hematite and ilmenite was successfully manufactured in a stirred media mill; however cuprite was characterised as the coarsest final product for the same grinding circumstances. Keywords: Wet stirred media mill, cuprite, vivianite, ilmenite, hematite

Jan 1, 2020

By N. B. Strydom

The data on heat stroke cases reported during the past five years were examined to determine the influence of age on the incidence of heat stroke. Relating the age distribution of these cases to that of the total number of Bantu mine workers showed clearly that the older men run a significantly higher risk of developing heat stroke than the younger men. Although the number of Bantu over 40 years of age in the industry is less than 10 per cent of the total they nevertheless accounted for 50 per cent of the fatal heat stroke and 25 per cent of the nonfatal heat stroke cases during the period under review. Age must, therefore, be recognised as a causal factor in heat stroke and the worker over 40 years of age should be allocated to work on surface, or in cool areas or to non-strenuous and supervisory tasks in hot areas.

By C. G. Hutson

The Zinc Corporation of South Africa (Zincor) were hosts to about forty members of the Institute at their works in Springs on Friday, 25th April, 1986. The programme, designed to give an overview of the industry and the part played by Zincor, comprised an introductory talk, a technical talk, a tour of the plant, and a luncheon. Radioactive waste in arid regions A conference on the disposal of radioactive waste in arid areas will be held in Cape Town during the period 7th to 12th September, 1986. It is recommended that engineers and scientists avail themselves of the opportunity to familiarize themselves with this relatively new multidisciplinary field of endeavor by attending the first ever conference of this nature to be held in South Africa. Iron control in hydro metallurgy The International Symposium on Iron Control in Hydrometalurgy will be held at the 16th Hydrometallurgical Meeting, from 19th to 22nd October, 1986, in Toronto, Canada.

Jan 1, 1986

By R. Meyjes, P. Davies

Keywords: Pyrometallurgy, furnace, smelter, engineering company Metix is a private smelter engineering company wholly owned by its management. Its main lines of business in the ferro-alloy industry being: - turnkey smelter projects (LSTK) - engineering, project, and construction management projects (EPCM) - specialised furnace equipment comprising: ? complete electrode columns, including forged copper pressure rings and contact shoes, as well as fail-safe slipping devices ? water-cooled roofs ? bus-tube systems ? feed systems ? cooling systems ? linings ? off-gas systems ? tap-hole drills & clay guns - furnace power supply systems - ore agglomeration & sinter plants - feasibility studies & due diligence reports - technical consulting for investment banks - project procurement & cost control Metix management experience includes around 130 combined years of contacts and experience in the South African smelter industries. Over 30 furnaces have been built, for processes including FeCr (high, medium, and low carbon), FeSi, FeMn (high and medium carbon), SiMn (ultra low carbon), Si metal, and FeV.

Jan 1, 2006

A Special General Meeting of The South African Institute of Mining and Metallurgy was held at Kelvin House, Johannesburg, on Wednesday, 20th August, 1986. Mr H.E. James (President) was in the chair and declared the meeting open at 15h45. Background The Chairman explained that the meeting had been called to consider a number of amendments to the SAIMM constitution. The proposed changes had been set out in detail in a document that had been mailed to all members on 4th July, 1986. He then briefly reviewed the background to the proposals, which is outlined in the Preface to the Annual Report (page 357 of this issue). The Chairman added that the Executive Committee of SACPE at its meeting on the 8th August, 1986, had resolved that the proposed amendments to the SAIMM constitution did comply with the requirements of Regulation RI525 dated 17th July, 1981, regarding the recognition by SACPE of a society as a Professional Engineering Institute.

Jan 1, 1986

By J. C. Zachariades, D. M. Fraser

The leaching of pyrolusite in acidic ferous sulphate solution was studied so that the important factors governing the kinetics of the reaction could be determined. The reaction is very rapid, and was monitored by continuous measurement and logging of the redox potential in solution by use of a microcomputer. The relationship between redox potential and manganese extraction was established empiricaly for each set of conditions by the use of a technique in which a calibration run was conducted in paralel with each leaching run. The study involved a number of batch leaching runs, and demonstrated that, of the variables investigated, only the initial ferous ion concentration and the reaction temperature afect the rate of manganese extraction. The final extraction did not vary. The reaction was modeled from the results by use of the shrinking-core model and Britan&apos;s activation-energy model. The later was found to provide a significantly better fit to the data.

Jan 1, 1991

By J. H. Bulloch

The paper gives an assessment of the available data on the linear elastic fracture mechanics involved in stress corrosion cracking and in the behaviour of reactor pressure-vessel materials exposed to a simulated pressurized water-reactor environment. As a result of the different experimental techniques used in the various studies mentioned, only a few detailed conclusions can be drawn. The data from constant-displacement wedge-opening loading (WOL) tests, with the exception of one study, exhibited very limited or no crack extension during exposure periods of up to 14000 hours. The data from constant-load tests indicated evidence of crack extension, but the nature and extent of the crack extension are still unclear. When crack extension did occur, it was exclusively transgranular in nature. Certain differences in the available test data are tentatively explained in terms of the experimental procedures used, and the need for a consistent code of experimental techniques is highlighted.

Jan 1, 1987

By P. Michalcik, V. Petros, M. N. Bagde, K. Holub

The objective of this paper is to present some results of laboratory experiments during the investigation of stress-strain characteristics of Carboniferous sandstones at dynamic loading. During these experiments increasing frequency and the constant amplitude of dynamic loading and/or constant frequency at different amplitude of dynamic loading were applied. Der Gegenstand dieses Artikels ist, irgendeine von Ergebnissen von Laborexperimenten bei Messung der Spannungs- und Deformationscharakteristik der Karbonsandsteine bei ihrer dynamischen Belastung vorzustellen. Im Laufe diesen Experimenten wurden entweder anwachsende Frequenzen bei konstanter Amplitude der dynamischen Belastung, oder gleiche Frequenzen bei variabler Amplitude der dynamischen Belastung verwendet. L&apos;objectif de ce papier est présenter quelques résultats d&apos;expériences de laboratoire pendant l&apos;enquête de caractéristiques de la tension – deformation de grès Carbonifère à sollicitation dynamique. Pendant ces expériences fréquence croissante et l&apos;amplitude constante de sollicitation dynamique et/ou fréquence de la constante à amplitude différente de sollicitation dynamique ont été appliquées.

Jan 1, 2003

By Siemag Transplan GmbH

At the Hansa Mine in Dortmund, Germany, coarse run-of-mine coal, up to 60 mm in particle size, has been brought to the surface hydraulically from a depth of 850 m since November 1977. Hoisting is done by a three-chamber pipefeeder, by means of which up to 400 t/h can be lifted. The pipefeeder operates without problems, and has so far shown itself to be efficient and reliable. Vertical hoisting can be carried out by water supplied from the surface, from underground, or from a surface water supply in combination with minewater from underground. Water that flows into the mine, which would in any event have to be pumped to the surface, can be utilized for hoisting operations. The energy costs per ton of coal for a lifting height of 850 m vary between 41 and 62 South African cents, and therefore lie within the range of costs that apply to conventional hoisting.

Jan 1, 1980

By G. Gafner

The paper gives the reasons for the development of a gold alloy of 990 fineness with good colour, durability, and mechanical properties, and explains why titanium was chosen as the alloying metal. Methods are described for the alloy?s production, solutionizing, and age-hardening. Mechanical properties are given as a function of deformation, age-hardening time, and temperature for three different starting states, and these properties are compared with those of some standard 14 and 18 ct jewelery alloys and pure gold. The effects of various salts and fluxes on the composition of the alloy after heat treatment at 1150, 800, and 500°C are discussed. These indicate how alloy scrap can be refined to pure gold, and how solutionizing and agehardening can be conducted without the use of vacuum equipment. The results of wear tests indicate that the alloy is more durable than normal coinage and jewelery alloys. Tips are given on the grain refining, soldering, and casting of the alloy.

Jan 1, 1989

By J. Zwartendyk, A. Azis

Optimizing the public gains from the exploitation of mineral resources By Dr A. AZIS and Dr J. ZWARTENDYK Every nation must decide how it should exploit its mineral resources so as to contribute most to its national objectives. It is argued that the present value of the future corporate income tax flow derived.from mineral exploitation may serve as a useful indicator in moving toward a taxation policy that would contribute optimally toward the greatest public benefit. The future stream of corporate income taxes depends largely on the mineral endowment, consisting of deposits now being mined, known unmined deposits, and unknown deposits. Unknown deposits may be estimated by geological inference. Both known and unknown deposits can be categorized according to grade and size, and divided into economic and uneconomic deposits on the basis of certain prices, costs, rate of return and taxation levels. Computer simulations can be run of discounted cash flow models at various taxation levels to showthe impact of taxation changes on future tax revenues.

By D. G. Krige

Some basic considerations in the application of geostatistics to the valuation of ore in South African gold mines by D. G. KRIGE, Pr. Eng., D.Se. (Eng.) Rand (Fellow) There is much room for improvement in the statistical procedures that have been used by gold mines over the past decade in the valuation of their ore reserves. Improvement depends on the establishment of the extent to which the patterns of frequency distributions and the directional variograms for the gold values vary from area to area within each section of a mine. The application of the lognormal distribution and of the De Wijsian variogram model for routine ore-reserve valuations requires detailed study before some of the reservations still held by mathematical statisticians can be met. This paper provides some preliminary evidence of the extent to which these models can be used with confidence, as well as suggesting how they can be applied to their full potential.

Jan 4, 1976

By Nareetsile S., J. Kabwe

In the past few years Orapa and Letlhakane Mines have investigated various new technologies to enhance and improve production. The goal has been to improve productivity, reduce operating costs and make the mines more profitable The advent of Global Positioning Systems (GPS) in the early ’80s brought about the realization of this concept. Orapa and Letlhakane Mines started using GPS in 1999 and it is now used atLetlhakane mine for surveying, vehicle tracking and dispatching and for floor control system. Orapa Mine uses GPS in surveying, floor control and drill navigation. It will also be used for vehicle tracking and dispatching in mid-2001 following the installation of a fleet management and control system. The introduction of GPS at both Orapa and Letlhakane mines have improved productivity and reduced operating costs in the areas of drilling, topographic survey and floor control. In vehicle tracking and dispatching GPS has allowed for real-time information management for timeous decision-making which optimized fleet run time hours.

Sep 1, 2001

By R. B. MacGillivray

The No. 2 Seam at Van Dyks Drift Colliery was found to be made up of six easily recognizable bands or plies of differing qualities. Not only did the plies differ from one another in quality, but their thickness and quality varied laterally across the mine. The economic production of a Iow-ash blendcoking coal for supply to the Japanese Steel Mills called for the mining of different portions of the seam. The portions that could be extracted economically varied in thickness and position within the No. 2 Seam across the mine. A unique system of selective mining had to be developed involving the dispatch of two separate streams of coal out of the mine. Conventional American mechanized pillarand-stall mining was used, and the productivity was improved by the installation of twin conveyor belts into a double-header section. The method of grade control that was instituted to ensure efficient extraction of the available coal reserves is described.

Jan 1, 1985

By C. Chapman, M. G. Reading, M. P. Amsden

Computer control of flotation at the Ecstall concentrator By M. P. AMSDEN, C. CHAPMAN, and M. G. READING Ecstall Mining Limited, a subsidiary of Texas Gulf Sulphur Company, operates the Kidd Creek Mine, a 10000 tons per day base metal producer, near Timmins, Ontario. Two different types of ore are mined and milled: copper-zinc and silver-lead-zinc. At the highly automated Ecstall concentrator the ores are processed by selective flotation in three individual circuits. One of the most important metallurgical tools for process control is a sample system incorporating continuous on-stream X-ray analysis. Recently this system was automated further by the addition of computer control of reagents for two copper-zinc flotation circuits. The computer programs, utilizing optimum seeking methods and smelter contract terms, have increased copper recovery by 1,1 per cent, zinc recovery by 1,4 per cent, and have reduced reagent costs by 16 per cent. Although not expected, copper and zinc concentrate grades were improved slightly as well.

By V. P. Kolosyuk, A. M. Bryukhanov

Occurrences of hazardous events (explosions of methane or coal dust, fires, outbursts) have been investigated and presented as a flow of events in time. It has been shown that flows of hazardous events in a long time span are homogeneous, stationary and no-after effect flows and can be considered as stationary Poisson flows. A flow of CH4/coal dust explosions that had happened for the last 27 years in Ukraine was analyzed. The explosions have been statistically processed. Practicability of agreement of statistical and theoretical data on mathematical expectation and mean square deviation of time interval between explosion and the explosion intensity has been stated. Probability of an emergency event in time is expressed through an exponential function, while mathematical expectation of an accident and mean square deviation of time interval between successive explosions are in inverse proportion to the accident intensity. Accident probability for practical purposes can be determined as a product of accident intensity by calculated time interval.

Jan 1, 2003