Search Documents

By B. Chambers, M. Yunovich

"Corrosion monitoring is commonly used in a variety of industries as a means of effective corrosion control programs to extend the life of the asset and ensure safe operation of the facilities. The majority of the monitoring tools have limitations and tradeoffs – e.g., sacrificing the longevity of the probe for higher measurement resolution. Linear polarization resistance (LPR) probes have the advantage of providing the operator with accurate, real-time corrosion rate data; however, the probes can only be deployed in conditions where the measured environment possesses certain minimal conductivity. In many instances, utilization of LPR probes in conditions with intermittent wetting (for example, conditions where the temperature fluctuates above and below the dew point) presents a challenge. To address this limitation, a special-design cooled corrosion probe has been developed, commercialized and integrated into the distributed control system in the plants. In addition to high-accuracy measurement of corrosion rates, the probe allows for monitoring of pitting corrosion. The most innovative feature of the probe is the cooling circuit, which brings the temperature of the sensors below the dew point, forcing precipitation of moisture and thus permitting corrosion measurements. Additionally, the probe was found to be well-suited for monitoring corrosion in crude distillation unit (CDU) overhead space, where condensation of hydrochloric acid may take place at relatively high temperatures, which would require relatively moderate amount of cooling to be imparted to the probe sensors. This paper presents laboratory-based data from a test simulating CDU refinery environment. A case study is presented to demonstrate how the cooling probe can be effectively used in the plants for corrosion monitoring.INTRODUCTIONConventional corrosion-monitoring techniques such as weight-loss coupons to assess corrosion damage are commonly used in plants1. However, the use of coupons is not only labor-intensive, but also does not deliver real-time corrosion data, thus effectively serving as a “backwards-looking” monitoring tool. Linear polarization resistance (LPR) probes have the advantage of providing the operator with accurate, real-time corrosion rate data; however, the probes can only be deployed in conditions where the measured environment possesses certain minimal conductivity."

Jan 1, 2012

By B. D. Pandey, D. Bagchi, Premchand

During the separation and recovery of metals from the ammoniacal leach liquor of Indian Ocean nodules by solvent extraction-electrowinning (SX-EW) in close-loop operation, the copper electrolyte containing ~40g/L Cu, 20 g/L Ni and 180 g/L sulphuric acid is bled-off to control the impurities. The recovery of copper and nickel as powders has been examined from the copper bleed solution following partial decopperisation, crystallization of mixed sulphate of the two metals and aqueous hydrogen reduction. From the dissolved sulphate solution containing 17.68 g/L Cu, 18.83 g/L Ni and 0.03 g/L Fe, the copper powder was precipitated at initial hydrogen pressure of 26 bar in an autoclave in 90 min at 140 °C. The residual copper from the spent solution was removed as sulphide and nickel powder was then recovered (99%) in two stages from a solution of pH 4.5 at 40 bar pressure and 190 °C. However, 98% nickel recovery in one stage was achieved when hydrogen reduction was carried out from an ammoniacal solution in the pH range 9-11. Copper and nickel powders were produced from the bleed solution with acceptable purity and specifications suitable for P/M applications.

Jan 1, 2004

By W. L. Brown

"The Normetal mine is about 7 miles east of the Ontario-Quebec boundary, and 13 miles north of the town of Dupuy on the Canadian National railway. The mine workings are largely on lots 44 and 45 in the south half of range 10, Desmeloizes township.The surface outcrop is reported to have been discovered by a trapper previous to 1925, but the details are obscure. The property was originally owned by the Canadian Exploration Company of Amos, Quebec, and was later transferred to Abana Mines, Limited. The latter Company carried out underground work from two shafts down to the 550-foot level. The property was acquired by Normetal Mining Corporation in 1931 and was reopened in 1933, when development work was carried down to the 800-foot level. The mine was closed down in 1935 because metal prices did not justify production at that time. It was reopened early in 1937 and milling commenced in September of that year. To the end of 1945, a total of 1,497,- 169 tons of ore was milled from which was produced 184,533 tons of copper concentrates containing 84,738,368 lb. copper, 2,744,100 oz. silver, 26,230 oz. gold, and 153,524 tons of zinc concentrates containing 163,752,433 lb . zinc."

Jan 1, 1954

By C. H. Sleeman

"The Iron Ore Company of Canada constructed a beneficiation complex in Sept-Iles, Quebec, to concentrate and pelletize earthy red hematite iron ores from the Knob Lake area. The plants were scheduled for initial production during the first quarter of 1973.Many problems have been experienced to date. Difficulties in controlling the process, excessive mechanical failures, design deficiencies and manpower-staffing problems have caused an extended start-up. The problems are now essentially solved and, with the completion of some additional minor modifications, it is expected that the plants will be producing premium iron ore pellets at or near rated capacity within the next immediate period."

Jan 1, 1976

By Peter Chmara

The measurement of dust concentration in Ontario mines since 1926 has been accomplished by konimetry, based on South African experience and methods. The introduction of a voluntary program of semi-annual surveys of air conditions at all operations throughout Ontario mines created a need for an instrument that would assess konimeter spots rapidly and accurately. The development of the Electronic Scanner, it is felt, answers this need. A program whereby all konimeter spot samples taken at Ontario mines will be counted at the MAP AO field offices in North Bay is described.

Jan 1, 1969

By S. Ross, M. Mayhew

"Kirkland Lake Gold introduced battery equipped vehicles (BEVs) at the Macassa Mine in 2011. The fleet of underground BEV haulage trucks and loaders has grown over the years to over 30 units, the world’s largest, currently handling approximately 80% of the daily production tonnage. The inflow and outflow of air occur through a limited number of relatively small openings, which limits the air volume delivered to the underground workings. In addition to improving air quality, the reduced heat load generated by the BEV (when compared to diesel equipment) had a significant positive impact in the workplace. The use of BEV for material handling has enabled increases in production that would not have been possible using diesel equipment.INTRODUCTIONMacassa mine was developed as a track-drift access mine, with the most recent shaft (#3) sunk in 1986. A new mining complex, the South Mine Complex (SMC) was discovered below the 5025 foot elevation south of traditional mining areas, and the majority of mining now occurs in the SMC. The discovery of that zone has led to an internal ramp which is used to access the SMC and haul ore to #3 shaft.The amount of airflow that can be moved through the mine is limited by the existing infrastructure to surface. This amount was recently increased to near its practical maximum from 118 CMS (250 kCFM) to 151 CMS (320 kCFM).Both diesel and electric equipment are used at Macassa. Tethered Load-Haul-Dump Machines (LHDs) have been replaced with Battery Electric LHDs, due to their increased mobility and depth of the mine. Battery trucks continue to replace locomotives to transport both ore and waste to the shaft, as mining has transitioned from tracked levels to trackless level and haulage has transitioned from horizontal levels to an inclined ramp.EQUIPMENT FLEET AT MACASSAMost of the primary material movers utilized at Macassa Mine are battery operated. As the mine goes deeper the battery technology will continue to be critical to the success of the operations. With over 300,000 hours of proven operation success, the battery technology and equipment will continue to be a major part of Macassa’s future."

Jan 1, 2019

By P. B. Demarsh

"Location: - Mine village of Perron, 11 miles east of Val d’Or in northwestern Quebec.Life; - Started production 1932, ceased 1951.Ore: - Flat lying quartz tourmaline veins within granodiorite. Gold values related to coarse segregations of pyrite. Specific gravity 2. 80.Capacity: - 30 tons 1932-35; 125 tons 1935-37; 350 tons 1937-51.Assay: - Heads 0.21 to 0.34 oz. per ton. Grade obtained by mining 600 tons daily, sorting belt reject 250 tons, balance to milling; tailings loss 0.003 to 0.005 oz. per ton; extraction 9 8. 5%.Grind: - 70% minus 200 mesh. Detention time 26 hours.Treatment: - Cyanidation process.Reagents: - Per ton, aero cyanide (NaCn) 0.36; unslaked lump lime 1.50; zinc 0. 03; lead acetate 0. 006; steel consumption 2. 50.Water: - Equal mixture of swamp creek water and underground seepage.Cost: - Per ton, sorting and crushing 0.21; grinding 0.31; cyanidation 0.11; filtration 0.05; precipitation 0.02; miscellaneous 0.22; total 0.92.Power: - Hydro-electric, 25 cycle, 12, 000 volts reduced to 550 volts.Labour: - 95% Maritime and European, balance Quebec and Ontario.Tailings: - Absorbed over large swampy area on barren mining claims.Personnel: - 1 7 men including supervision.Flow sheet: - Canadian Mining Manual 1947"

Jan 1, 1966

By Marcio Luis S. Godoy

The Salobo Project will be the first Vale operation to use an HPGR mill to process copper-gold ore. The mine is located in Para state, southeast of the Amazon region in Brazil. The circuit was designed to treat 12 million metric tons per year of finely disseminated sulphide ore with high hardness. The comminution circuit comprises a gyratory primary crusher, secondary crushing utilizing two cone crushers, two 2 x 1.5 m HPGR operating in closed configuration with 6 mm screens, followed by two 26 x 40 ft ball mills. The concentration circuit consists of two rougher flotation stages using mechanical cells, regrinding with vertical mills, three cleaner stages with columns and one cleaner scavenger stage in mechanical cells. The concentrate is dewatered, filtered and transported by trucks and train to the port, to be exported. The circuit was designed on the basis of data obtained from a comprehensive laboratory and pilot plant campaign. The ore variability was assessed through simulation using data from a drilling core characterization program. The start-up of the industrial plant is planned for 2011. This paper describes the main aspects of circuit design, as well as information related to the beginning of the project construction.

May 1, 2010

By Werner Unland, Nick Holl

"The paper presents the engineering design and experience gained so far with a dewatering system for an open-pit uranium mine planned at Key Lake in Northern Saskatchewan.The results of hydrogeological investigations preceding engineering exhibit an extensive unconfined overburden aquifer hydraulically connected with the underlying Athabasca Formation and basement rocks, both of relatively low hydraulic conductivity. The overburden aquifer is embedded in a bedrock trough, with the deepest depression between the planned pits. The hydrogeological data were used in a numerical dewatering model simulating groundwater flow atdifferent stages of the pit development.Based on the model results, the engineering design had to provide for different pumping rates, varying between 1.0 and 0.21 ms/sec. This problem was solved by using a double line pressure system. The design concept for the complete peripheral discharge system and the well design used for 26dewatering wells are discussed.Experience with reverse-circulation techniques applied for the construction of the dewatering wells is presented. Theoretical and practical considerations which led to the constructionof wells of different diameters are discussed.The design of the in-pit dewatering system provides for seepage ditches, horizontal drains, pit-bottom sumps and inpit dewatering wells where required."

Jan 1, 1980

By T. Guan, G. Fu, X. Zhou, L. Deng

"One kind of tailings from gravity separation of polymetallic mine contains 0.5–0.8% SnO2. The proportion of –0.037 mm size fraction of the tailings is 37.12%, and the distribution rate of SnO2 is 60.32% in it. For this tailings, two processing technology was carried out. One was felt-shaking table gravity separation in which the concentrate with a grade of 30% SnO2 at a recovery of 10% was obtained. Another was flotation-gravity separation in which the concentrate with a grade of 51.20% SnO2 at a recovery of 51.69% was obtained, but the dosage of collectors was as much as 990g/t. Therefore, the experimental research on the influence of grain size composition on the cassiterite recovery were conducted. The results show that: (1) the flotation recovery of the cassiterite distributed in +0.043 mm size fraction is only 10%, flotation recovery is not suitable for it; (2) a portion of cassiterite distributed in –0.01+0.005 mm size fraction could be recovered by flotation, but the tin flotation performance will be worsened rapidly and the dosage of collectors will be increased due to the increase of the content of –0.010 mm size fraction; (3) flotation processing is not suitable for –0.005 mm size fraction of the tailings. According to the results, a new technology has been carried out, that is discarding tailings by gravity separation-hydrocyclone desliming-flotation-gravity separation processing flow. The processing index is close to that of the flotation-gravity separation processing flow, and the collector dosage is decreased to 360 g/t by this processing technology. And, it has been achieved that the cassiterite slime is recovered economically and reasonably.INTRODUCTIONAs the density of cassiterite is higher than that of gangue, gravity separation is considered to be a low cost, pollution free, and effective process for cassiterite recovery (Wills, 2009). However, cassiterite is a kind of fragile mineral, over crushing is easy to take place and a large amount of slime is inevitably produced in the crushing and grinding of cassiterite. For the cassiterite slime exists in –0.043 mm size fraction, the efficiency of gravity separation decreases sharply. The production practice shows that, for the fine cassiterite, the recovery of tin exists in –0.043 mm +0.010 mm size fraction is about 13% through shaking table gravity separation, and the tin exists in –0.010 mm size fraction is almost impossible to be recovered by gravity separation. If flotation is adopted to recover fine cassiterite, the problems of high reagent dosage, high cost, environmental pollution, and poor economic benefit would take place. Therefore, the recovery of cassiterite slime is a worldwide problem. A key way to increase the utilization of tin resource and increase the economic benefit of tin mines is developing suitable beneficiation process for fine cassiterite."

Jan 1, 2016

By N. Shi, T. G. Joseph

ABSTRACT A revised equilibrium approach to evaluate dipper-ground interactions during the dig cycle of ultra-class mining shovels operating in soft unblasted uniform ground conditions is presented. A review of previous approaches, leading to an outline of the modifications and ground condition considerations, is made in support of the reasoning and basis for the derivation presented. An analytical solution is provided to the scenario of a cable shovel dipper digging in soft ground material such as oil sands.

Jan 1, 2012

By S. Banisi, M. Maleki-Moghaddam

Direct observation of charge shape and its motion in industrial mills is not possible; therefore, a combination of analytical and physical studies is used to determine charge trajectory. Software packages, which predict charge motion consider only the outermost layer of charge (single ball) and ignore the charge and the interactions of grinding elements. In the new version of the GMT (Grinding Media Trajectory) software, the effect of liners specification and bulk load on charge shape and trajectory are considered. The charge trajectory was measured in a laboratory mill with the diameter of 100 cm and length of 21.5 cm with the transparent end and compared with that of the old version of GMT. Four types of polyurethane rings were accurately machined to scale down the liners arrangements at two industrial mills. The model mill was operated at 55, 70 and 85% of the critical speed for five levels of mill filling (10, 15, 20, 25% and 30% by volume). The experiments indicated that the end walls effect was negligible for the model mill with the length of 10.8 cm and beyond. The proposed relationships to correct the trajectory and charge shape were validated by using the new liner of the Gol-E-Gohar iron ore company AG mill. The positions of shoulder, toe, toe departure and impact points were predicted with the relative errors of 5, 0.7, 2 and 0.2%, respectively. The GMT software was updated with the new relationships. The results of GMT simulation indicated that when the lifter face angle increased from 7 to 30°, the distance between the charge impact point and the toe decreased from 40.1 to 11.2° for 30% filling. The change in the position of the impact point meant increasing the probability of charge impacting the toe, not the liner which favored more efficient comminution practice.

Jan 1, 2016

By Charles Tkaczuk

In order to remain competitive the mining industry must keep up with changes in technology. Many innovative technologies from the mining perspective are commonplace in other industries. A ?Global? review of technologies will often reveal existing technologies that can be innovatively applied in the mining industry. Industries, which are rife with proven solutions include, medicine, biotechnology, security, manufacturing, telecommunications, etc. This paper addresses the communications aspect of mining where greater productivity, lower costs and the ability to quickly react to mining related events is obtained through an increase in remote monitoring and operating control. A review of the communications systems in place globally reveals technologies that, with minimal modification, can be immediately applied to the mining environment. We discuss the concept, advantages and implementation of existing communications technology from an industry that is not usually associated with the mining industry. This technology will form the basis of a solid platform on which can be built a state-of-the-art process monitoring, control, and communication system. This lays the groundwork for providing one solution to the underground mining industry?s most difficult problem, establishing a reliable, maintainable and cost-effective underground bi-directional wired/wireless data, video and analog communications system. We need look no further than our own doorsteps to find such a solution. The cable that you see coming from the simple green or brown box on the boulevard into your home contains hundreds of television broadcast channels, FM radio channels and data channels. And if you have a set-top box, you are in control of it all. The Cable Television Broadcast Distribution System suppliers of today are at the leading edge of converging all the different methods of communications onto a common carrier, coaxial cable or fibre optic cable. There is no fundamental difference between providing a reliable communications network to a city/neighbourhood/home/personal computer than there is to a mining operation/underground level/equipment or person. The principle is the same. Only the application is different. Realizing this, we can capitalize on the efforts of other industrial sectors, to solve our communications problem. Where else can you find a solution to a problem that is mature, having been developed with the input of thousands of engineers, and having hundreds of millions of dollars spent on research and development, manufacturing, distribution, global presence and engineering support?

May 1, 2003

By W. W. Rudolph, L. N. Trevani, P. R. Tremaine

UV-visible spectroscopy, Raman spectroscopy, and vibrating tube densimetry have been used in our laboratory to determine equilibrium constants of aqueous species at temperatures as high as 325 °C. The UV-visible and Raman spectra of solutions containing metal complexes and ionized acids or bases can be used to yield formation constants by applying curve fitting methods to resolve the contribution of each species. Colorimetric pH indicators identified by Johnston and coworkers at the University of Texas (Austin) provide an alternative means of determining ionization constants and the pH of complex mixtures. High precision density measurements over the same range yield standard partial molar volumes, which are key parameters for "equations of state" for aqueous species. Examples are given for the copper-ammonia system, simple carboxylic acids, and the iron-sulphate system.

Jan 1, 2004

Infrared spectroscopic data collected using HyloggerTM technology is being used to assess the mineral composition of Archean iron ore bedrock and Cenozoic detrital units in Western Australia’s Pilbara region. Analysis of infrared spectra enables quantification of: (1) composite iron mineralogy, (2) composite clay mineralogy, (3) hydrous silicates and (4) carbonate mineral abundances. Stratigraphic and rock mass unit logging of core has identified several detrital and bedrock units recognisable across the Pilbara. However, due to alteration related to mineralisation, weathering and later stage precipitate overprinting, it can often be difficult to assess the detrital-bedrock boundary and the occurrences of specific geotechnical units in the detritals and bedrock, particularly when using non-core drilling techniques and traditional geochemical assays. Infrared spectroscopic data collected concurrently on core from several sites has shown distinct correlation against existing unit subdivisions and associated geochemical parameters. Where infrared spectroscopic data have also been collected on rock chips recovered from reverse circulation infill drilling, these correlations allow robust geological and geotechnical models to be developed based on the typical mineralogical-geochemical signatures. The geotechnical sub-units identified in core can be readily distinguished using the various iron and clay minerals captured by the HyloggerTM technology as opposed to total iron, potassium, and alumina captured by geochemical assays. Further, some of the minerals targeted by infrared spectroscopic analysis (eg gibbsite, white mica, vitreous goethite) and their ubiquitous presence as the products of weathering, assist in recognition of various ancient weathering surfaces and help to define the origin of the material, whether bedrock or detrital. Overall, HyLogging of core and chips allows important mineralogy focussed data to be captured at minimal additional financial outlay. Correlations against geochemical unit identifiers are robust both within deposits and between deposits. Significant improvements in the confidence of geological and geotechnical models are attained.

Jan 1, 2015

By L. H. Shang

The 319 Al-Si alloy is one of the most prominently used aluminium-based alloys in motor vehicle and engine applications, Microporosity present in 319 alloy castings reduces the load bearing capacity of the castings, The quantitative prediction of microporosity levels in Al-Si castings has been a subject of much interest for several years. In this research a new criteria function, tf 1,98 R13° (tf: local solidification time, R: cooling rate) was developed by multiple regression analyses, correlating thermal data from simulation studies to experimentally obtained microporosity values. This new criteria function gives a general prediction of microporosity in 319 Al-Si castings.

Jan 1, 2005

The quality of refractory bricks and castables could be determined by direct measurements of their material properties such as elastic properties, porosity, density, etc. using conventional static or non-destructive testing (NDT) dynamic techniques. Quality monitoring of refractory linings is much more challenging and complicated. The static methods require undesirable drilling and sample extractions from the furnace structure. A more desirable alternative is the use of NDT techniques for material quality estimation. The Acousto Ultrasonic-Echo (AU-E) technique is a new stress wave propagation approach for monitoring the quality of refractory linings in operating furnaces. In this paper, the conceptual methodology for the AU-E technique is described, the capabilities and limitations are expanded, and the results from two case studies are discussed.

Jan 1, 2005

By Stéphane Robert

This document presents estimates of future "total cash cost per ounce" and "minesite cost per tonne" that are not recognized measures under United States generally accepted accounting principles ("US GAAP"). This data may not be comparable to data presented by other gold producers. These future estimates are based upon the total cash costs per ounce and minesite costs per tonne that the Company expects to incur to mine gold at the applicable projects and do not include production costs attributable to accretion expense and other asset retirement costs, which will vary over time as each project is developed and mined. It is therefore not practicable to reconcile these forward-looking non-GAAP financial measures to the most comparable GAAP measure. A reconciliation of the Company's total cash cost per ounce and minesite cost per tonne to the most comparable financial measures calculated and presented in accordance with US GAAP for the Company's historical results of operations is set forth in the notes to the financial statements included in the Company's Annual Information Form and Annual Report on Form 20-F, for the year ended December 31, 2009, as well as the Company's other filings with the Canadian Securities Administrators and the SEC.

May 1, 2011

By Fathi Habashi

This Historical Metallurgy Note is the final part of a three-part series, the first two of which appeared in the November- December, 1997 and January, 1998 issues of the Bulletin. This series of articles is dedicated to the memory of Nikolai Maximovitch Pereskuryakov (1940- 1994), Rector of Saint Petersburg Mining Institute from 1992 to 1994 who passed away unexpectedly at the age of 54, shortly after celebrating the 275th Anniversary of the Institute.

Feb 1, 1998

By Fathi Habashi

This Historical Metallurgy Note is the second part of a three-part series, the first of which appeared in the November- December issue of the Bulletin. Part III will be published in February, 1998. This series of articles is dedicated to the memory of Nikolai Maximovitch Pereskuryakov (1940-1994), Rector of Saint Petersburg Mining Institute from 1992 to 1994 who passed away unexpectedly at the age of 54, shortly after celebrating the 275th Anniversary of his Institute.

Jan 1, 1998