Search Documents

By Elwood G. Haney, R. N. Parkins

Stress corrosion cracking of two heats of 18 pct Ni maraging steel in rod form immersed in an aqueous solution of 0.6N NaCl at pH 2.2 has been studied on un-notched specimens stressed in a hard tensilf machite. Austenitizing temperature in the range 1830 to 1400 F has been shown to have a marked influence on the propensity to crack, the loulest austenitizing- temperature producing the greatest resistance to failure. In the nzosl susceptible conditions, the cracks followed the original austenile grain boundaries; but when tlze steels zcere heal treated to inproze their resistance to stress corrosion, the cracks becatne appreciably less branched and slzouqed significant tendencies to become trans granular. Electron metallography of the steels indicated the presence of snzall particles, possibly of titanium carbide, along- the prior austenite grain boundaries and these particles u:ere more readily detectable in the structures that were most susceptible to cracking. Crack propagation rates, which appeared to be dependent upon applied stress and structure, were usually in tlze reg-ion of 0.5 mm per hr and may, therefore, be e.xplained on tlze basis of a purely electrochetnical ,nechanism. However, there is some ezliderzce from fractography that crack extension may be assisted by ttlechanical processes. Anodic stit)zulation reduced the tiwe to fracture, although cathodic currents of small magnitudes delayed cracking-; further increase in cathodic current resulted in a sharp drop i,n fracture litne, possibly due to the onset of hydrogen ewbrittlement. THE use of the high strength maraging steels, with their attractive fracture toughness characteristics, is restricted because of their susceptibility to stress corrosion cracking in chloride solutions. Although this limitation has resulted in investigations of the stress corrosion susceptibilities of these steels, there have been few systematic studies aimed at defining the various parameters that determine the level of susceptibility. It is the case that the usual tests have been performed with the object of defining some stress or time limit, on unnotched or precracked specimens, within which failure was not observed,' but while such results may be of some use in design considerations, they are necessarily concerned only with the steels as they currently exist and not with their improvement to render them more resistant to stress corrosion failure. This omission may be considered unfortunate because the indications are that stress corrosion in maraging steels shows dependence on structure in following an intergranular path, and since experience with other systems of intergranular stress corrosion crack- ing is that susceptibility may be varied by modifying heat treatments, a similar effect may be expected with maraging steels. It is sometimes from such observations that a fuller understanding of the mechanism of stress corrosion crack propagation begins to emerge, leading in time to the development of more resistant grades of material. The present work was undertaken to study only one aspect of the influence of heat treatment upon the cracking propensities of the 18 pct Ni maraging steel, namely the effect of austenitizing temperature, although certain ancillary measurements and experiments have been undertaken. EXPERIMENTAL TECHNIQUES Most of the measurements were made on a steel, A, having the analysis shown below, although a few results were obtained on a steel, B, having a slightly different composition. Both steels were supplied in the austenitized condition, A as 3/8-in-diam rod and B as 1/2-in.-diam rod. Cylindrical tensile test pieces were machined from the rods: the overal length was 2 1/2 in., the gage length 1 in. and the diameter 0.128 to 0.136 in. The stress corrosion tests were carried out with the specimens strained in tension in a hard beam testing machine, the necessary total strain being applied to the specimen over a period of about 30 sec, after which the moving crosshead was locked in position and the load allowed to relax as crack propagation proceeded; the load relaxation was recorded. The load was applied after the specimen had been brought into contact with the corrosive solution, the latter being contained in a polyethylene dish having a central hole through which the specimen passed, leakage being prevented by the application of a film of rubber cement. The specimen was in contact with the solution for over half of its gage length and the solution was exposed to the air during testing. The solution was prepared from distilled and deionized water to which NaCl was added, 0.6N, and the pH adjusted to 2.2 by HCl additions. The composition of the solution

Jan 1, 1969

By R. E. Ogilvie, N. L. Peterson

Diffi-lsion measurements were conducted at all compositims in the bcc solid solution of the U-Nb system employing incremental couples at composition intemals of 10 at. pct. Diffusion coefficients were determined by the Matano method from concentration gradients obtained with the electron-probe microanalyzer. The activation energy for inter-diffi-lsion as a function of compositim shows three distinct regions: 1) 80 to 100 pct U.6= 30 kcal per mole; 2) 20 to 80 pct U, $ - 70 kcal per mole; 3) Oto 20 pet U, Q = i40 kcal per mole. The frequency factor, fi0 and the activation energy $ were found to be roughly related by the following equation: log Do ^9.7 X IO-5Q -6,6. The Kirkendall marker movement indicates that DU is larger than DNb between 16 and 100 pct U and DNb is larger than DU from 0 to 4 pct U. FOR practical as well as fundamental reasons, the rates of diffusion in alloys are of considerable consequence. Most solid-state reactions are largely dependent upon the diffusion of atoms through the lattice structure and along grain boundaries. The high-temperature strength and reasonable nuclear properties of niobium have prompted its use as a reactor material in contact with uranium fuel. Hence, diffusion data for the U-Nb system are of considerable importance. In the previous diffusion study1 on the U-Nb system using pure element couples, reliable data were obtained only in the range of 0 to 10 at. pct Nb due to the large variance of the diffusion coefficient with composition. Also, a large Kirkendall effect and considerable porosity in the uranium-rich areas of the specimen were reported, which suggests that the true diffusion coefficients are somewhat larger. The purpose of the present study was to obtain reliable diffusion coefficients at all compositions using incremental diffusion couples with intervals of 10 at. pct. In view of the abnormal self-diffusion be- havior of y uranium2-4 and some other bcc transition elements,&apos;-&apos; it was felt that a comparison of the interdiffusion coefficients in the bcc U-Nb system with those of Reynolds et al.9 for the fcc gold-nickel system might shed some light on the diffusion mechanism involved. Both systems have similar phase diagrams, in that complete solid solubility exists above a miscibility gap. EXPERIMENTAL PROCEDURE The uranium used in this investigation was obtained through the courtesy of Argonne National Laboratory. An analysis of this material detected only Si-30, A1-7, C-6, N < 10 and 0-18 ppm. The niobium was electron-beam melted material obtained from Stauffer-Temescal. The gaseous impurities were less than 50 ppm, and the spec troc hemical analysis showed Ta-500 and W-200 ppm. U-Nb alloys were prepared at composition intervals of 10 at. pct by melting the appropriate amounts of the pure elements in an arc furnace. The buttons were inverted and remelted 6 times to assure complete mixing. The buttons were then wrapped in molybdenum foil, canned in Zircaloy-2 or stainless steel, and hot rolled 30 pct reduction in thickness at temperatures between 850" and 1100°C. Alloys with 10, 20, 30, 40, and 90 at. pct Nb rolled quite easily under these conditions, but the 50, 60, 70, and 80 pct alloys remained brittle. After melting and rolling (when possible), the alloys were annealed for 24 hr at a temperature within 100°C of their melting point in a dynamic vacuum of better than 4 x 10-8 mm Hg. These treatments produced alloys which were homogeneous on a 1 p scale within the detectability limits of the electron probe. During fabrication, the alloys picked up as much as 100 ppm Mo and 100 ppm Zr. Other elements checked for but not found were Co, Cr, Fe, Mn, Ni, and Ti. The grain size of the annealed samples ranged from 3 mm for the uranium-rich alloys to 0.3 mm for the niobium-rich alloys. This permitted measurements of the concentration gradients in the diffusion samples without crossing more than one or two grains, thereby eliminating any grain boundary effects. The specimens were bonded by theU&apos;picture frame" technique as reported by Kittel.10 Specimens of composition b)U + (100 - x)Nb were sandwiched between two specimens of composition (x + 10)U + (90 - x)Nb after they were ground flat and parallel

Jan 1, 1963

By J. Alfred Berger, O. M. Katz

The Zv-Hf-H ternary system was studied between 500° and 900°C at pressures less than 1 atm of hydrogen gas between 1 and 60 at. pct H. A new and unique microgravimentric apparatus was used. Cizanges of slope on pressure-hydrogen composition isothernis delineated phase boundaries. These boundaries separatecl the three regions, a, 0, and y—so designated to correspond to the regions of the Zr-H binary system—from the multiphased areas between them. A eutectoidal decomposition was found with the ß region phase or phases decornposing into a lamellar product on quenching to rool ter,zperatuve. Reproducible decomposition-pressure hysteresis occilrved lnainly at lower hydrogen cornpositions and at lower temperatures across multiplzase vegions between a and 0 and a and y. Tire effects of hqfniur7z on the hydriding charactevistics of zirconiurrz weYe as follows: 1) stabilization of the a and y vegions while destabilizing the 0 region; 2) a/?preciable elevation of the decomposition pressrkres in the multiphase region between the a and /3 field; 3) ~nouenzent of the eutectoid reaction to high te~nperatures; 4) reduction in the total qiiantity of hydrogen absorbed under one atmospheve of Hz p7-essure; and 5) introduction of a split deconzposilion at the eiitectoiclal poinl in pa?? of the ternavy. Assuru~ptions based on an ir-2terstitial vandonl-solulion rtioclel 0.f hydrogen in metals slzowed that the bindit~g energy between solute sites prednnzinatecl at low /i?!dvogen concentrations. However, at high hydrogen contents the entropy was the predorninatlt factor in determining the stability of the Zr-Hf-H al1o.s. This was interpreted to mean a scarcity of filrtlzer itltevslilinl solute sites caused by hydrogen-hydvogen intet-actions in the metal lattice. INTEREST in the reaction of hydrogen with metals has increased in the past few years for the following reasons: 1) the formation or use of high hydrogen potential environments in nuclear reactors; 2) the reaction of hydrogen with alloys in nuclear reactors with the accompanying deleterious effects on the mechanical and corrosion properties; 3) the theoretical implications of thermodynamic data on the theory and rules of alloy formation in the metal-hydrogen systems; 4) the use of hydrogen-containing fuels in rocket engines; 5) the need for a process of making fine metal powders of high-melting reactive metals; and 6) the beneficial impregnation of superconducting alloys with hydrogen. In nuclear pressurized-water reactors, the problem exists of limiting the hydrogen pickup of zirconium alloys which are utilized as fuel cladding, heat shields, and support members. In general, zirconium alloys have good mechanical and corrosion-resistant properties in high-temperature water. However, hydrogen is absorbed from the corrosion reaction between metal and water, greatly accelerating the formation of the corrosion product ZrOz as well as mechanically embrittling the underlying metal. In addition, recent observations1 at zirconium to hafnium welds showed that secondary elements in zirconium can have an appreciable, and somewhat unexpected, effect on hydrogen absorption. This paper lists the thermochemical data in the range 500" to 900°C for the equilibrium reaction of four high-purity Zr-Hf alloys with hydrogen. Phase boundaries and thermodynamic functions are determined while the structural data will be presented in a future paper. In general, the Zr-Hf-H system approximates the well-known, eutectoidal, Zr-H diagram2,3 with modifications introduced through the behavior of hafnium.4,5 The Hf-H system,&apos; published while this work was in progress, provided a consistent trend with the Zr-Hf-H data. PREPARATION OF Zr-Hf ALLOYS Table I presents a complete flow chart of the preparation procedure. The zirconium and hafnium crystal bars were completely immersed in high-purity kerosene and slowly cut into thin wafers. Wafers were then cold-sheared into approximately 1-g pieces, thoroughly cleaned, weighed, and inserted into the furnace. The alloys, B-2, B-4, B-6, and B-8, were then nonconsumable arc-melted under 500 mm of purified argon. Additional purification of the argon was accomplished by melting a large titanium button each time an alloy was re-melted or a different alloy melted. Each alloy button, which weighed 25 g, was remelted four times in an approach to complete homogeneity. Material losses were less than 0.02 wt pct. Alloy buttons were alternately cold-rolled and vacuum-annealed into 10- and 20-mil sheets. Table I1 gives the composition of the four alloys used. Very little elemental segregation existed be-

Jan 1, 1965

By Thomas R. Mager

An in.t!estigation has been made of the equilibrium conditions at 1200°C in the reaction between hydrogen sulfide gas and sulfur dissolved in Fe-Si alloys From this the equilibrium constant, activity coefficient, and activity of sulfur in solution were calculated. A number of studies of the equilibrium of sulfur with iron and iron alloys have given closely agreeing results from which the activity and free energy of the dissolved sulfur may be found. Sherman, El-vander, and chipman1 discussed the significant researches of dilute solutions of sulfur in liquid iron prior to 1950, and the results of this study indicated that the relationship between the ratio of PH2S/PH2 in the environment and the percentage of sulfur in solution is not a linear one. Morris and williams2 studied the equilibrium conditions in the reaction between hydrogen sulfide gas and sulfur dissolved in liquid iron and Fe-Si alloys, and reported that silicon dissolved in iron has a pronounced effect on the equilibrium conditions. They found that the activity of sulfur in iron is increased by the addition of silicon. At a silicon content of 4 pet the activity coefficient of sulfur was about twice that for sulfur dissolved in pure iron. Sherman and chipman3 investigated the chemical behavior of sulfur in liquid iron at 1600°C through the study of the equilibrium: H2 + S = H2S; K = PH2S/PH2 . 1/as [1] From the known equilibrium constant of the reaction between H2, H2S, and S and the experimental data, the activity of sulfur in the melt was determined. They found that the activity coefficient of sulfur defined as fs = as/%s is increased by silicon and decreased by manganese. Morris4 and Turkdogan5 also reported that manganese decreases the activity coefficient of sulfur in liquid iron and iron-base alloys. A recent technique of sulfur analysis developed by Kriege and wolfe6 of the Westinghouse Research Laboratories permits an accurate sulfur analysis of 0.5 * 0.2 ppm in the range of 0.1 to 3 ppm, whereas in the range of 3 to 50 ppm the accuracy is ±1 ppm. This technique of sulfur analysis was utilized in this experiment. Previous unpublished data reported that sulfur analysis by the combustion technique was not accurate below 20 ppm. EXPERIMENTAL PROCEDURE Five 5-lb ingots of high-purity Fe-Si were prepared. Three of these ingots were prepared without the addition of manganese but with a variation of silicon contents from 2 to 4 pet. The remaining two ingots contained 3 pet Si with the addition of manganese. Ingots were made at each of three silicon levels: 2, 3, and 4 pet. No alloys were made with less than 2 pet Si since below approximately 1.8 pet Si the binary alloy exhibits a to ? transformation. The two additional ingots of 3 pet Si-Fe were made at each of two manganese levels: 0.20 and 0.50 pet. To minimize the effects, if any, of impurities on the activity of sulfur on Si-Fe, the best metals available were used for melting. All ingots were vacuum-melted in magnesium oxide crucibles. After obtaining samples for chemical analyses, the ingots were processed. This consisted of hot rolling and subsequently cold rolling the alloys. Each ingot was hot-rolled at 1000°C, reheating between every pass to minimize grain growth. All heating was done in a protective argon atmosphere. The slabs were hot-rolled to strips 50 mils thick. After hot rolling, all the material was pickled to remove the scale formed on the surface of the strip during hot rolling. The material was then cold-rolled to 12-mil strips. Single strips of the material used in this experiment were hydrogen-annealed at 1200°C for 16 hr in an alumina tube. Chemical analyses of strips M-1, M-3, M-4, M-7, and M-8 are given in Table I. Sulfur, silicon, and manganese analyses were made from the millings from the cold-rolled 12-mil strips. The oxygen analyses were made from slugs of the as-cast material. The hydrogen sulfide used in these experiments was supplied from cylinders containing a mixture of argon and 1 pet hydrogen sulfide. The parts per million of hydrogen sulfide were determined from the analysis of the exit gas of the annealing furnace during each anneal. The flow rate of hydrogen was approximately 1 liter per min in all anneals. The

Jan 1, 1964

By D. A. Augenstein, L. V. Amundson

Operators of coal preparation plants use equipment such as large-capacity dump trucks and bulldozers to haul, spread, and compact refuse material to conform to federal and state regulations governing the disposal of solid waste. For example, federal regulations require that refuse be spread and compacted in layers not more than 0.6 m (2 ft) thick. If the refuse layers or piles have poor load-bearing characteristics, movement of equipment over them becomes extremely difficult. The increasing cost and limited space for the construction of settling ponds extensively used for fine refuse disposal are leading to the growing practice of dewatering the fine refuse by means of vacuum disk filters and combining the resulting filter cake with coarse refuse for waste bank disposal. However, this filter cake usually contains more than 25% moisture. Therefore, when it is combined with coarse refuse, the moisture level of the total refuse may become high enough to impair the load-bearing strength of the refuse. Precisely this problem and the attendant difficulties of moving heavy equipment arose when vacuum disk filters were installed at a preparation plant in West Virginia. Combining the moist filter cake with the coarse refuse generally results in a 12% moisture level for the total refuse at this plant. At this moisture level, the refuse can still be handled with some dif¬ficulty by the equipment. However, the problem has frequently been compounded after rains. The experimental program described in this paper tested the following methods of improving the load-bearing properties of coal refuse: moisture reduction, addition of crushed coarse refuse, addition of fly ash, addition of lime, and addition of a mixture of lime and fly ash. In terms of a balance between economic and technical considerations, the most effective method was demonstrated by laboratory and plant tests to be a 2% to 5% addition of lime. Test Program During formulation of a test program aimed at improving coal refuse stability, a number of treatment techniques were selected for evaluation of their effect on refuse load-bearing characteristics. The reduction of refuse moisture was the first technique considered, since moisture content plays a key role in the bearing strength of a bulk solid. The reasoning was that a very small reduction in refuse moisture, provided it could be accomplished with minimal effort and cost, would be sufficient for eliminating refuse disposal problems most of the time. At the same time, it was recognized that periods of rainy weather would offset moisture-reduction measures. Other techniques selected for evaluation because of their potential for improving refuse-bearing strength at reasonable cost were: addition of crushed coarse refuse, the addition of fly ash, and the addition of lime. A simple one-dimensional laboratory compaction test was designed for evaluating the effect of each of these techniques on refuse-bearing strength. Those techniques that gave best results in the laboratory would then be tested in the preparation plant in West Virginia. Laboratory Tests The laboratory test for evaluating each of the techniques involved the application of weight to a load module placed on a refuse sample in a container. The distance the load module sank with an increasing amount of applied weight was measured, and the relationship between module displacement and loading was obtained. The refuse container was large enough to minimize the influence of wall effects, and to decrease the effect of the container bottom, a test was terminated when the load module sank to about three fourths the depth of the container. Initially, an attempt was made to conduct compaction experiments with samples of total plant refuse. However, the presence of + 0.13 m (+ 5 in.) material in the refuse interfered with the mechanics of the test, and the large amount of material required for a representative sample made testing extremely tedious and time-consuming. To avoid this problem and because it was believed that only the fine components of the refuse were the major cause of the stability problem, tests were conducted with 13 mm X 0 (1/2 in. X 0) material from the total plant refuse. The equipment consisted of a 0.46 m (18 in.) cubic container, a loading module with 62 cm2 loading area, weights totaling 450 kg, and a portable concrete mixer for combining water and additives with the refuse. Refuse samples of about 110 kg dry weight were used for each test. Experimental compaction test data were evaluated by plotting the linear displacement of the load module vs. loading. During compaction tests, the vertical displacement of the load module was measured at each loading value. The plot of

Jan 1, 1980

By R. L. Skaggs, D. T. Peterson

The effect of carbon in solid solution on the plastic behavior of thorium was studied by measuring the flow stress of Th-C alloys from 4.2" to 573°K and at several strain rates. Carbon was found to strengthen thorium primarily by increasing the thermally activated component of the flow stress. The strengthening due to carbon was directly proportional to the carbon content and decreased rapidly with increasing temperature up to 423" K. The flow stress also increased with increasing strain rate. The strengthening appears to be due to a strong short-range interaction between carbon atoms and dislocations. A yield point was observed in the Th-C alloys which increased with increasing carbon content. JTREVIOUS study of the mechanical properties of thorium has been confined largely to the measurement of the engineering properties. Work prior to 1956 has been summarized by Milko et al.1 who reported that additions of carbon to thorium sharply increased the room-temperature strength. In addition, the yield strength was observed to decrease rapidly over the temperature range from 25" to 500°C. In 1960, Klieven-eit2 measured the flow stress of thorium containing 400 ppm C. He found that over the temperature range from 78" to 470°K the flow stress was strongly dependent on temperature and rate of deformation. A drop in the load-elongation curve, or a yield point, was observed over most of the above temperature range. Above 470°K, the flow stress was nearly independent of temperature and strain rate. This strong temperature and strain rate dependence of flow stress is not generally observed in fcc metals. It is, in fact, more typical of the behavior reported for bcc metals. Bechtold,3 Wessel,4 and conrad5 have pointed out the striking difference between the commonly studied bcc metals and fcc metals in regard to the effect of temperature and strain rate on the flow stress. Zerwekh and scott6 studied the plastic deformation of thorium reported to contain 12 ppm C. They found that this material did not obey the Cottrell-Stokes law as expected for fcc metals. In addition, they found values of the activation volume smaller by an order of magnitude than expected for an fcc metal. They concluded that thorium was strengthened by a randomly dispersed solute. Thorium differs from many other fcc metals that have been studied extensively in that it shows a relatively high carbon solubility at room temperature. Mickleson and peterson7 report the solubility limit at room temperature to be 3500 ppm C. The lowest value reported is that of Smith and Honeycombe8 who report the limit to be 2000 ppm C at 350°C. The pres- ent investigation was a systematic study of the flow stress and yield point phenomenon of thorium over a broad range of carbon content, temperature, and strain rate. EXPERIMENTAL PROCEDURE The thorium used in this investigation was produced by the reduction of thorium tetrachloride with magnesium as described by Peterson et a1.&apos; Chemical analysis of the original ingot after arc melting and electron beam melting is shown in Table I. Alloys were prepared by arc melting this thorium with high-purity spectrographic graphite. Threaded specimens with a gage length 0.252 in. diam by 1.6 in. long were used for the constant stress or creep measurements. These specimens were machined from rod which had been cold-rolled and swaged to % in. diam. Tensile specimens were prepared by swaging annealed 3/8 -in.-diam rod to 0.102 *0.001 in. The as-swaged wire was cut to lengths of 2 in., annealed, and the center 1-in. gage length elec-tropolished to 0.100 ±0.001 in. The specimens were gripped for a length of 3 in. at each end by a serrated four-jaw collet which was tightened by a tapered compression nut. No slipping occurred in the grips and negligible deformation was observed outside the 1-in. gage length. Both the creep and tensile specimens were annealed at 730°C under a vacuum of 1 x X Torr. The resulting structures consisted of equiaxed recrystallized grains with a grain size of 3200 grains per sq mm for the tensile specimens and 2200 grains per sq mm for the creep specimens. After the specimens were prepared, samples were analyzed for nitrogen, oxygen, and hydrogen. The results of these analyses are given in Table 11.

Jan 1, 1969

By Kim C. Harden

INTRODUCTION The purpose of the following discussion is to present the state of the art of solution mining. Since the economics of a mining method ultimately determines its applicability and viability this presentation shall revolve around the costs of in- situ solution mining. First the assumed physical characteristics of the hypothetical ore body are described, followed by the appropriate operating assumptions. Then after a brief discussion on the type of surface plant to be used, the assumed project time tables and costs for Texas and Wyoming are presented. Finally, the economics of in-situ uranium leaching are analyzed through the use of discounted cash flow rate of return analysis. ORE BODY CHARACTERISTICS The assumption of the ore body characteristics is probably the most variable portion of this discussion. The characteristics that have been used are based mainly on state of the art technology, however, consideration of the most common depths of ore, ore thicknesses, and permeabilities also influenced these assumptions. In addition, it is assumed that these assumptions are equally applicable to Texas and Wyoming. The average grade of the ore is assumed to be .09% U308 with no apparent disequilibrium. The average thickness of ore is 2.29 m (7.5 ft) which results in an average grade-thickness (GT) of .675. The assumed depth to the top of the ore is 121.92 m (400 ft), the ore density is placed at 1.78 gm/cc (18 cu ft/ton), the porosity is estimated to be 28% and the permeability 1 darcy. These assumed ore body characteristics are shown in Table I. In addition, it is specified that the costs to be later discussed are based on a minimum GT cut-off of 0.15. It is more common to use GT cut-offs of 0.30 to 0.50 but GT cut-offs as low as 0.15 in conjunction with a minimum grade of 0.05% U308 have been used in the past with success and is considered state of the art. The ultimate percentage of uranium recovered from the ore is left to the discretion of the reader since the costs and economics are based on pounds recovered by the surface plant. OPERATING AS.SUMPTIONS An annual production rate of 200,000 lbs U308!yr was chosen for this example. In order to maintain this production rate, based on the ore body characterized above, a flow of 4731 liter/min (1250 GPM) with a recovery solution grade averaging .039 gm U308/liter is assumed. A regular 5 spot well field pattern is used with a well spacing of 21.5 m (70.7 ft) between like wells and 15.24 m (50 ft) between unlike wells. This well spacing gives each well an area of influence equal to 232.25 sq m (2500 sq ftl. An excess wells factor of 1.17 is used to estimate additional monitor wells and well field boundary wells. Each production well is expected to yield an average flow rate of 37.85 liter/min (10 GPM). In addition it is assumed that the ore body has a good shape in that it is not tenuous and narrow but has at least an average width of 200 ft. The process chemistry required for this ore body is assumed to be based on the sodium carbonate System- Oxygen is the chosen oxidant. Sodium chloride elution followed by precipitation with hydrogen peroxide makes up the remaining portion of the process. A fluidized up-flow ion exchange system is specified. The operating assumptions are listed in Table II. Restoration of the ore body shall be assumed to be accomplished through the use of ground water flush. Other methods may be considered as having to fall within the costs estimated for a ground water flush in order to be economic. In Texas it is assumed that a high capacity disposal well (200 GPM +I is required and in Wyoming evaporation ponds covering approximately 35 acres are to be used. No specific cost has been given to restoration. Instead only the additional capital investment for restoration equipment is given. Then, one year of restoration operating expense is estimated and included as the operating expense for one year beyond the last pound of U308 produced. It is also assumed that restoration will be pursued in the mined out areas of the ore body contiguous with ongoing production.

Jan 1, 1980

By M. J. Marcinkowski, A. S. Sastri

A detailed compressive stress-strain analysis and transmission electron microscopy investigation has been made of the deformation behavior occurring in a 50 at. pct Ni-Ti (hypoeutectoid) alloy and a 54.5 at. pct Ni-Ti (hypereutectoid) alloy. In the case of the hypoeutectoid alloy, three stages of work hardening are observed. Stage I occurs at a very low stress and is associated with plastic deformation via martensite formation. Stage 11 is characterized by very rapid work hardening and is due to difficulties in causing further deformation in the fine martensite aggregate produced in Stage I. Stage III which occurs at very high stress levels is characterized by smaller work hardening rates and is due to the plastic deformation arising from alternate reconversions of the original martensites to martensites of varying orientation. Rapid quenching of the hypereutectoid alloy leads to very high yield strengths and is related to a fine precipitate dispersion that such treatment brings about. The present investigation represents the final phase of a three-part study directed toward an understanding of the solid-state transformations in near equi-atomic Ni-Ti alloys as well as the deformation mechanisms associated with these alloys. In the first part,"2 to be henceforth referred to as I, it was found that alternate simple shears on {112} planes and in (111) directions convert the parent B2 structure in the equiatomic NiTi alloy into two distinct close-packed monoclinic martensites. All of the marten-sites were of this type, whether they were formed by cooling or by plastic deformation, whether induced to form in bulk samples or in thin foils, or whether examined in the electron microscope at room temperature or below. On the other hand, in the second part of this investigation,3 to be reffered to as 11, it was shown that upon slow cooling to about 640°C. alloys in the neighborhood of NiTi which possess the B2 structure transform eutectoidally into their equilibrium phases Ti2Ni and TiNi3. However, preceding the formation of these equilibrium phases a series of metastable intermediate phases are formed. This paper will set as its goal the elucidation of the remarkable deformation behavior exhibited by NiTi. In particular, Buehler and Wiley4 have found equiatomic NiTi to be surprisingly soft, while Buehler et al.5 have shown this alloy to possess a memory effect: i.e., upon bending at room temperature it will revert to its original shape when heated to above about 50°C. In I it was shown that NiTi was soft in the sense that the yield stress was low; nevertheless, the alloy work-hardened at an extremely rapid rate to very high stress levels. On the other hand, the hypereutectoid alloys with somewhat higher nickel, say 54.5 at. pct (60 wt pct) have enormously increased yield strengths compared to those of the equiatomic alloys. In order to determine the atomistic processes giving rise to the above behavior, it was decided to examine samples that were wafered from bulk specimens deformed in compression to various strains using the techniques of transmission electron microscopy. EXPERIMENTAL TECHNIQUE All of the alloys used in the present investigation contained either 50 at. pct Ni (55.06 wt pct) or 54.5 at. pct Ni (60 wt pct) and were arc-melted in the form of a finger using the same techniques described in I and II. The finger was capsulated in a stainless-steel jacket and swaged at 850°C into rods. Compression specimens 0.300 in, long and 0.200 in. in diam were machined from these rods. In order to completely re-crystallize the samples and remove residual stresses, all of them were capsulated in evacuated quartz, annealed for 1/2 at 1050°C. and then furnace-cooled. Compression tests were carried out in an Instron tensile testing machine covering a range of temperatures from —196° to 200°C using procedures described previously.6&apos;7 In all cases crosshead speed was 0.02 in. per min. Wafers 0.015 in. thick were spark-cut from the cylindrical samples at 45 deg to the compression axes after they had been deformed to the desired strain. These specimens were then spark-planed to about 0.005 in. and then electrochemically thinned for examination by transmission electron microscopy as described in I.

Jan 1, 1969

By George W. Riter

OUR mineral-land laws need revising so as to provide definite title at the outset to the mineral deposits within any definite piece of land. The laws as they now stand, especially those applicable to lodes, breed uncertainty as to rights of possession prior to patent; and to my mind this is the worst feature of all, worse even than the apex bugbear. It is now almost impossible for anybody to tell-with certainty what mineral rights exist within any area that is not covered by patent, or whether any valid rights exist at all. Our system is unique in permitting individuals to appropriate and exploit mineral lands of the public domain without notice of any kind to the Federal government, and to relinquish them without any ceremony at all. The result is a clouded record that cannot be cleared up until each claimant is put to some sort of final proof. In order to accomplish this, new Federal legislation will be required. The requirements for a mineral survey and the proceedings for patent have always been cumbersome and expensive; and perhaps out of regard for the poor claim owner, who can ill afford the outlay for that sort of thing, the law does not require him to go. through it unless he chooses to do so. Consequently, every active mining district has become encumbered with tangled groups of doubtful or conflicting locations, whose rights and boundaries, when any valuable ore is found, must usually be determined by lawsuits that are as expensive and as distressing as the stakes are high. So deeply has litigation entered into our mining system that a claim whose rights have never been disputed would probably be set down offhand, by $miner of the old school, as of no value. Think of the litigation over rights of possession on the Com-stock lode—12 leading companies involved &apos;in an aggregate of 245 suits within a period of less than eight years! Ambiguous local records; the chance of erroneously placed or obliterated monuments; doubt as to the sufficient performance of the statutory annual labor; uncertainty as to prior conflicting or overlapping locations; anxiety as to the changing attitude of the Department of the Interior and the Forest Service—such considerations as these make an unpatented mining claim an unclean thing in the eyes of possible investors. Is it any wonder that they keep themselvesand their money at a safe distance,

Jan 1, 1915

By Robert F. Brindisi

There are approximately thirty to forty operating mills in the United States which are currently producing uranium yellow cake. This figure includes a significant number of in situ and by-product operations however the conventional acid leach flowsheet depicted in Figure 1 is the most common process used by domes- tic yellow cake producers. Ground ore is leached with sulphuric acid and the solids are separated from the pregnant liquor and washed in a series of counter- current decantation thickeners. After clarification of the pregnant liquor, uranium is recovered from the solvent extraction/stripping circuit by the addition of ammonia with precipitation of ammonium diuranate, or simply yellow cake. The yellow cake precipitate is then thickened in a conventional thickener before re- porting to the dewatering/washing unit operation. De- watered solids subsequently report to thermal drying, and clarified liquor from the dewatering/washing step is recycled to the yellow cake thickener. The yellow cake dewatering/washing unit operation is generally accomplished using either a solid bowl centrifuge or a rotary vacuum drum filter. In most cases the underflow from the yellow cake thickener is pumped to the dewatering/washing unit operation at approximately fifteen to twenty percent solids. For the purpose of this discussion ammonium diuranate, the product of ammonia precipitation from a conventional acid-leach uranium mill flow sheet, as discussed earlier, will be considered. With only slight adjustment this discussion will be equally applicable to sodium diuranate or uranium perioxide precipitates and to either in situ or by-product operations where such precipitates are generated. Some of the domestic uranium mills which have selected solid bowl centrifuges instead of vacuum drum filters for the dewatering/washing unit operations are listed in Figure 2. Why have these uranium mills, as well as others not listed, chosen to use the solid bowl centrifuge for this particular application? It is simply a matter of performance, reliability and economics. In the remainder of this paper the performance, initial cost, installation cost, maintenance and power consumption of both the solid bowl centrifuge and the rotary vacuum drum filter will be com- pared. In order to provide a consistent basis for comparison the appropriate sized (centrifuge or filter) unit for the dewatering/washing of 400 to 500 pounds per hour of yellow cake solids will be considered. Such a flow will usually be generated by a typical 3,000 ton per day (acid-leach) uranium mill.

Jan 1, 1980

By F. E. Werner, B. L. Averbach, Morris Cohen

THAT bainite formed near the M, temperature bears a striking r esemblance to martensite tempered at the same temperature has been shown by the electron microscope.&apos; By means of electron diffraction,&apos; it has been established that carbide and cementite are present in bainite formed at 500°F (260°C); these carbides are also found in martensite tempered at 500°F (260°C).&apos; The investigation reported here is concerned with an X-ray study of the matrix phases in lower bainite and tempered martensite. These phases have turned out to be dissimilar in structure; the matrix of bainite is body-centered-cubic while that of tempered martensite is body-centered-tetragonal. A vacuum-melted Fe-C alloy containing 1.43 pct C was studied. Specimens of 16 in. diam were sealed in evacuated silica tubing and austenitized at 2300°F (1260°C) for 24 hr. One specimen was quenched into a salt bath at 410°+7 °F (210°+4°C), held for 16 hr, and cooled to room temperature. The structure consisted of about 90 to 95 pct bainite, the re: mainder being martensite and retained austenite. A second specimen was quenched from the austen-itizing temperature into iced brine and then into liquid nitrogen. It consisted of about 90 pct martensite and 10 pct retained austenite. The latter specimen was tempered for 10 hr at 410°+2°F (210°+1°C). The specimens were then fractured along prior austenite grain boundaries (grain size about 2 mm diam) by light tapping with a hammer. Single aus-tenite grains, mostly transformed, were etched to about 0.5 mm diam and mounted in a Unicam single crystal goniometer, which allowed both rotation and oscillation of the sample. Lattice parameters were measured by the technique of Kurdjumov and Lyssak. This method takes advantage of the fact that martensite and lower bainite are related to austenite by the Kurdjumov-sachs orientation relationships Thus, the (002) and the (200) (020) reflections can be recorded separately, permitting the c and a parameters to be determined without interference from overlapping reflections. According to these findings, the matrix phase in bainite is body-centered-cubic and, within experimental error, has the same lattice parameter as ferrite (2.866A). On the other hand, martensite, tempered as above, retains some tetragonality, with a c/a ratio of 1.005t0.002. Most workers in the past have assumed that bainite is generated from austenite as a supersaturated phase, but the nature of this product has not been established. The question arises as to whether bainite initially has a tetragonal structure and then tempers to cubic, or if it forms directly as a cubic structure. If it forms with a tetragonal lattice, it might well be expected to temper to the cubic phase at about the same rate as tetragonal martensite. The martensitic specimen used here was given approximately the same tempering exposure, 10 hr at 410°F, as suffered by the greater part of the bainite during the isothermal transformation. About 50 pct bainite was formed in 6 hr at 410°F. On tempering at this temperature, martensite reduces its tetragonality within a few minutes to a value corresponding to 0.30 pct C.&apos; Further decomposition proceeds slowly, and after 10 hr the c/a ratio is still appreciable, i.e., 1.005. Thus, even if the bainite were to form as a tetragonal phase with a tetragonality corresponding to only 0.30 pct C, which might be assumed to coexist with e carbide, it would not be expected to become cubic in this time. It seems very likely, therefore, that bainite forms irom austenite as a body-centered-cubic phase and does not pass through a tetragonal transition. The carbon content of the cubic phase has not been determined, but it could easily be as high as 0.1 pct, within the experimental uncertainty of the lattice-parameter measurements. It has been postulated that retained austenite decomposes on tempering into the same product as martensite tempered at the same temperature. There is now considerable doubt on this point. The isothermal transformation product of both primary and retained austenite at the temperature in question here is bainite," and the present findings show that bainite and tempered martensite do not have the same matrix. Acknowledgments The authors would like to acknowledge the financial support of the Instrumentation Laboratory, Massachusetts Institute of Technology, and the United States Air Force.

Jan 1, 1957

By Albert Hoskinson

PROGRESS on the earth depends to a large extent upon the rapid inter-change of ideas and commodities between the various nations of the world. The smooth flow of commerce, by which these ideas and com-modities move, is accelerated by accurate and complete maps of the various land and water areas of the earth, The production of accurate maps depends upon a complete knowledge of the figure and dimensions of the object to be charted, therefore a knowledge of the shape of the earth is a prime necessity for accurate charting purposes. Gravity observa-tions were first undertaken to aid in determining the shape of the earth so that the geodetic surveys of its land and water areas might be more accurately connected to form an undistorted map. A large part of the earth&apos;s surface is water and it is therefore necessary to get gravity values at sea as well as on land before a complete and accurate figure of the earth can be determined. Dr. F. A. Vening Meinesz, of Holland, was the first scientist to perfect a pendulum instrument that would accurately measure gravity at sea. He had previously developed a multiple pendulum apparatus for measur-ing gravity upon swampy and unstable land areas in Holland and it was therefore quite natural that he should adapt the instrument to give accurate results upon a still more unstable support, the surface of the sea. His instrument as perfected gives satisfactory results when mounted in gimbals on any vessel where the roll and pitch are not more than about 5° and where the vibrations from rotating machinery and wave action are not large enough to cause the pendulums to shift on the knife-edges. This degree of stability can be obtained on surface craft only in protected waters or on very calm days. Therefore, Dr. Meinesz mounted his instrument in a. submarine so that he could submerge below the disturbed surface waters and get the desired stability in nearly any kind of weather by simply diving to greater depths. Most of the gravity-at-sea work has been done with a Meinesz instrument and a very large number of the observations have been made by Dr. Meinesz himself. He has occupied nearly 1000 sea stations and probably has traveled as many miles by

Jan 1, 1938

By Robin O. Williams

Robin 0. Williams (Oak Ridge National Laboratory)— The authors have questioned the degree to which the coherency strains between the iron-rich and chromium-rich phases are isotropic as proposed in Ref. 5 on the basis of the difference between the elastic properties of the two phases. The relative magnitude of the stresses is determined by the moduli as shown by Eqs. [2], [3], and [4] of Ref. 34. However, the moduli of the two phases have no direct bearing on the uniformity of either the stress or strain within either phase. The idea that the strains are isotropic within each phase (but normally of different magnitude and always of different sign) is based entirely upon the experimental observation that X-ray line broadening has not been detected even when the particles become rather large. It has not proven possible to grow the particles sufficiently large that they lose coherency. Based upon this lack of line broadening one can estimate an upper limit for the nonuniformity of the strains within each phase as follows. It is considered possible to detect line broadening if it is as great as 10 pct of the separation of the K, doublet for the (211) line using chromium radiation. The doublet separation would correspond to a total strain of 0.0017 such that the total variation of lattice parameter relative to the average lattice is now k0.05x0.0017 or something less than ± * For the present case the strain in each phase is roughly 0.002 such that the variation of strain within a phase will not exceed 5 pct. It is stated that the expression derived for strengthening for the hydrostatic straining as observed in this system would substantially overestimate the magnitude due to dislocation flexure. This is contrary to the conclusion reached in the original paper34 for the present range of particle sizes. What is the lowest temperature at which a has been observed to form in this alloy? M. J. Marcinkowski, R. M. Fisher, and A. Szirmae (nutlzors&apos; reply)— -Williams&apos; arguments based on X-ray findings for a chromium-rich precipitate and an iron-rich matrix strained to a common lattice parameter are certainly convincing. This being the case, there are no shear components of strain associated with the precipitate-matrix aggregate to interact with the shear components of the dislocation stress fields, contrary to the opinion expressed by the present authors. On the other hand, the present authors, in spite of this error, did not expect the shear interactions to be significant. The chief objection to Williams&apos; model in the present case is that the various segments of the dislocation line are assumed to pass from one potential valley to the next independently of neighboring segments. This is only true for a highly flexible dislocation line, i.e., one whose radius of curvature is something less than the center to center distance between precipitate particles which amounts to about 90A in the present alloy. In order to maintain this curvature, an externally applied shear stress of at least 230,000 lb per sq in. would be required or about four times the observed stress. It is therefore concluded that the dislocation lines move rather rigidly through the lattice. This being the case, the forces on the dislocation resulting from the hydrostatic interaction between the stress fields of the edge-dislocation components and the precipitate particles should average out to zero; that is particles above the below the slip plane produce forces on the dislocation of opposite sign and therefore will cancel when averaged over the entire length of the dislocation. On the other hand, since the dislocation is not perfectly rigid, Williams&apos; model may lead to some strengthening, but far less than that predicted. A second and equally serious objective to using Williams&apos; strengthening model for the present alloys is that profuse wavy slip due to the motion of screw dislocations played a predominant role not only in the unaged alloys but in the fully aged ones as well. Since the screw dislocation has associated with it only shear components of stress the hydrostatic strengthening model no longer applies. In view of these arguments the present authors must reject Williams&apos; model of strengthening as being pertinent to the present alloy system. The present authors have made no detailed study of the lowest temperature at which a forms in the quenched ferritic alloys. None was ever observed n the alloys aged at 500°C so that forma-tion must occur at temperatures higher than this and was therefore not a factor in the present study.

Jan 1, 1965

By Charles E. Wait

HAVING had some experience in the use of gasoline-gas in a laboratory, I have been induced by frequent inquiry to present a few hints concerning it, which I hope may be of some value to those who are out of the reach of coal-gas, and who contemplate using this gas. While I will not delay to describe the method by which this gas is made, it may not be out of place to note that, unless frequent charges are put into the carburetter, the gas is variable in richness. This may be partially avoided, it is said, by repeatedly pumping from one cell in the carburetter to another. If a machine is in constant use for many months without re charging, the gas becomes rather poor for illuminating purposes ; but in this condition it may be burned in a Bunsen burner with advan tage. Could the gas be used always in this condition, no difficulty would be experienced, and it would be quite satisfactory for general laboratory purposes. Considerable annoyance, however, is experi enced whenever the machine is filled with gasoline. The Bunsen and other burners then produce a flame too smoky to be used with com fort, and, in fact, with most of them, a full supply of air; turned on at the base of the burner, will not suffice to completely burn off all the carbon. Finding it necessary to adopt some method by which I could get a flame free from unconsumed carbon, I adopted a plan which has in every way proved satisfactory. In addition to the pipe conveying the gas to the table, and ar ranged with a stopcock, there is brought to the table, within a fern inches of the gas-pipe, another pipe, conveying air direct from the pump. This pipe is also arranged with a stop-cock. The air- and gas-pipes are now connected with one pipe by a T joint; and to this last pipe is attached, by rubber tubing, the Bunsen or other burner. I have successfully used this simple system in connection with both small and large Bunsen burners, a burner with three tubes, arid a Fletcher burner; and recently I have added a new still to our equipment, and have been tising with it a Fletcher special high power burner No. 6, to which this system has been applied. With

Jan 1, 1886

By R. T. Hukki, A. M. Gaudin

Previous work on the principles of comminution has shown: (I) that the surface produced is proportional to work input (Rittinger law,1a-3); (2) that there is regularity to the weight distribution of the fragments according to size.4-10 In this paper it is brought out that the surface on the fragments is distributed in definite and simple relation to size. The experimental work has involved: I. Construction of an apparatus capable of measuring the surface of mineral fragments independently of the chemical composition of the fragments and independently of the site of the surface; 2. Refining the methods available for measurement of particle size; 3. Designing and building a crusher capable of operating on very small quantities of mineral, if necessary on single crystals, and in such fashion as to minimize handling losses of material. Complete experiments have been carried out with massive quartz and individual quartz crystals. partial experiments, lacking surface measurements, have been made with glass spheres, galena, sphalerite, fluo-rite, salt and coal. Introduction The existence of regularity in weight distribution with size was noted many years ago, especially by A. 0. Gates;&apos; the subject was also studied in detail by one of us.6 In the latter paper it was shown that rocks can be divided into two classes: homogeneous rocks, which show no preferential breaking, and heterogeneous rocks, which show preferential breaking at the grain size of the rock. It was shown, furthermore, that the fragments obtained by rupturing a homogeneous rock occur (in the fine range) in such abundance as to permit the writing of a relatively simple equation to relate the weight retained on a screen to the screen opening. With screens of which the openings are in constant ratio, the weight retained, w, is related to the screen size x by the equation w = Cxm [I] In this equation C and m are experimental constants. A plot of weight retained against particle size is a straight line of slope m if the scales for x and w are both logarithmic. In the fine range, the slopes of the size-distribution graphs plotted according to the method described above vary within a limited range. An inspection of a number of size-distribution data by various experimenters indicates that the slope very seldom exceeds 1.0, but is usually greater than 0.7. More recently, schuhmann8 proposed a method of charting that has so many advantages of its own that it has been used primarily in this work. For fine particles Schuhmann has found that the data are represented by the equation (x)m k [2]

Jan 1, 1947

By A. M. Gaudin, R. T. Hukki

Previous work on the principles of comminution has shown: (I) that the surface produced is proportional to work input (Rittinger law,1a-3); (2) that there is regularity to the weight distribution of the fragments according to size.4-10 In this paper it is brought out that the surface on the fragments is distributed in definite and simple relation to size. The experimental work has involved: I. Construction of an apparatus capable of measuring the surface of mineral fragments independently of the chemical composition of the fragments and independently of the site of the surface; 2. Refining the methods available for measurement of particle size; 3. Designing and building a crusher capable of operating on very small quantities of mineral, if necessary on single crystals, and in such fashion as to minimize handling losses of material. Complete experiments have been carried out with massive quartz and individual quartz crystals. partial experiments, lacking surface measurements, have been made with glass spheres, galena, sphalerite, fluo-rite, salt and coal. Introduction The existence of regularity in weight distribution with size was noted many years ago, especially by A. 0. Gates;&apos; the subject was also studied in detail by one of us.6 In the latter paper it was shown that rocks can be divided into two classes: homogeneous rocks, which show no preferential breaking, and heterogeneous rocks, which show preferential breaking at the grain size of the rock. It was shown, furthermore, that the fragments obtained by rupturing a homogeneous rock occur (in the fine range) in such abundance as to permit the writing of a relatively simple equation to relate the weight retained on a screen to the screen opening. With screens of which the openings are in constant ratio, the weight retained, w, is related to the screen size x by the equation w = Cxm [I] In this equation C and m are experimental constants. A plot of weight retained against particle size is a straight line of slope m if the scales for x and w are both logarithmic. In the fine range, the slopes of the size-distribution graphs plotted according to the method described above vary within a limited range. An inspection of a number of size-distribution data by various experimenters indicates that the slope very seldom exceeds 1.0, but is usually greater than 0.7. More recently, schuhmann8 proposed a method of charting that has so many advantages of its own that it has been used primarily in this work. For fine particles Schuhmann has found that the data are represented by the equation (x)m k [2]

Jan 1, 1947

By J. M. McKenzie

p-n junctions to detect and measure the energy of single quanta of electromagnetic radiation are described. Useful energy range is from 1 kev to several Meu. Achieved energy resolution varies from 30 pct at 6 keu to 0.12 pct at 2 Mev. Parameters affecting the perfornzance of the present detectors and desired of a new material are discussed. DURING the last 6 years semiconductor detectors have been used extensively to detect and to measure the energy of charged particles. These detectors are made from reverse-biased p-n junctions. Electron-hole pairs are created in the depletion region of the junction, Fig. 1. The carriers are separated by the electric field and give rise to a pulse of current in the external circuit. This current pulse is proportional to the number of carriers and hence to the energy deposited in the depletion region by the ionizing event. More recently the discovery of the lithium drift process, first in silicon&apos; and then in germanium,2 has extended the use of semiconductor detectors to the detection and the energy measurement of single quanta of electromagnetic radiation. These detectors now have a useful measurement range extending from the soft X-ray region, about 6 kev, to the hard y ray region of several Mev. Surface-contoured avalanche diodes can be used to extend this range down to 1 kev. There is however a desire for other materials suited to higher operating temperatures, and particularly for those materials with high y ray stopping power. The most important advantage of the semiconductor detector over gaseous and scintillation detectors is the average energy, E, required to form an electron-hole pair. Fig. 2 shows the quantum efficiency for germanium as a function of photon energy.3 At the band-gap energy, 0.7 ev, an electron-hole pair is generated by the absorption of the photon and the quantum efficiency is unity. The quantum efficiency remains constant at unity between 0.7 and 3 ev. It then increases as additional electron-hole pairs are formed by secondary ionization of the initial photoelectron. The rate of increase is about 1 electron-hole pair per 3 ev (actually 2.9 ev for germanium and 3.6 ev for silicon). This figure is constant irrespective of the particle type (electron, proton, a particle, heavy ion) and energy. In an ionizing event an incident particle of energy E will create N = E/e ion pairs. The statistical fluctuation in this number is proportional to &. The fractional energy resolution is therefore proportional

Jan 1, 1968

By T. R. Graham, J. R. Long

This report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau&apos;s War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. Preliminary Work In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, o to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944

By J. R. Long, T. R. Graham

This report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau&apos;s War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. Preliminary Work In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, o to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944

By J. D. Livingston

THE hardening of alloys by the precipitation of a second phase has long been an important technological process. One approach towards improving our understanding of this phenomenon has been a correlation of mechanical properties with such parameters as particle size and inter par ticle spacing.&apos; Several reviews of such data have appeared.2-4 A major limitation to this approach has been that for most alloys the particles are submicroscopic in size in the range of optimum hardness. Precipitation-hardening copper-cobalt alloys, therefore, are of interest, because the ferromagnetic properties of the precipitate make it possible to measure particle size, number of particles, and so forth, from magnetic measurements alone.5, 6 Livingston and Becker7 have applied these techniques to a study of precipitation hardening in an alloy of 2 pct Co in copper. It was found from magnetic measurements that nearly all the cobalt to be precipitated was out of solution within a few minutes at 600°C, whereas the peak in tensile yield stress was not attained until a much longer aging time. Thus during the first 1000 min of aging time at 600°C the Yield stress was increasing while a constant volume of precipitate was coarsening, i.e., while particle size and interparticle spacing were increasing. Peak yield stress was reached at an average particle radius of about 70A. The earlier study was confined to one alloy at one aging temperature, so that the volume fraction of precipitate was fixed and, therefore, particle size and interparticle spacing could not be independently varied. The work has now been extended to several alloys of varying percentage cobalt in copper, and to aging at various temperatures. It was hoped that such a study might clarify the relative importance to precipitation hardening of particle size, interparticle spacing, and volume fraction of precipitate. EXPERIMENT The alloys studied contained 0.7, 1.3, 2.0, and 3.2 wt pct Co in copper. They were prepared from electrolytic copper and electrolytic cobalt in a vacuum -induction furnace, worked to 3/8-in.-diam rod, and machined into tensile specimens with a gage section 1 1/2 in. long and 3/16 in. in diam. All specimens were given a solution treatment consisting of a 30-min anneal in nitrogen at 1000° C followed by a quench into iced brine. Subsequent aging was done in nitrogen and followed by a water quench. Average grain diameter was approximately 0.01 in.

Jan 1, 1960