Search Documents

By Wilson Acchar, Fernando Barcelos, Luis Carlos Pereira

"Porous ceramics have been extensively investigated as structural materials for flow of fluids in many applications, such as filters for molten metals, water purification and hot gases, thermal protection systems and heat exchangers. This class of material must have two special features: high permeability and mechanical strength. However, these parameters are influenced in different ways by the processing method and the consequent cellular structure. In this work two different types of commercial ceramic filter materials are investigated. Characterization included the evaluation of the strength values as well as the permeability behavior and microstructural analyzes of the surface fracture. The results indicate that the strength values are strong dependent on the filament defects.IntroductionCeramic materials with a cellular structure have been extensively investigated as structural materials for flow of fluids applications [1-3]. Microstructural aspects such as morphology, size of the cell and the degree of interconnectedness are mainly parameters that influence the properties of these porous materials [4-6]. The most used industrial process to produce cellular ceramics for filter application is the polymeric sponge replication method. This technique consists in dipping the polymer foam into slurry containing an appropriate binder and the necessary ceramic materials, followed by a heating treatment [2,5].Mechanical properties of cellular ceramics depend basically on cell size, degree of interconnectedness and density [1,2,5,8,9]. Materials used as filters required a good strength and also permeability values. These properties are inversely proportional to each other. Higher porosity increases permeability values but decreases the strength values [1,2,5]. The objective of this work is to study the strength resistance of a commercial porous ceramic material (10, 20 and 30 ppi) based on silicon carbide."

Jan 1, 2012

By Jian Li, S. Penttila, W. Zheng

"Materials selection for Gen IV supercritical water reactor in-core components faces major challenges due to severe operating condition. Beside high-temperature mechanical properties, SCC and general corrosion resistance of commercially available materials are also major focuses in recent research. Recent reports suggest that certain types of surface modifications are beneficial to SCW corrosion resistance. In this study, the effects of surface modifications are investigated, and possible mechanisms for improved corrosion performance are discussed.IntroductionThe current Canadian pressure-tube supercritical water reactor (SCW) design specifies a core outlet temperature of 625°C under 25 MPa of pressure, with peak cladding temperature as high as 850°C. Challenges in materials selection include high-temperature mechanical properties, corrosion resistance, SCC resistance and radiation damage. Most of the SCW corrosion test results available are below 730°C. Early work by Allen [1] summarized the corrosion resistance of alloy groups including Ni-based super alloys, stainless and ferritic/matensitic (F/M) steels that can potentially be used for SCW reactors. F/M steels can only be used at low temperature sites (e.g. down stream piping). At 500°C and 25 MPa, F/M steels develop a thick but mechanically stable oxide layer. However, the long term stability of the surface oxide layer is largely unknown. Ni-based alloys appear to form very thin surface oxide, however pitting was observed in the vicinity of some intermetallic precipitates [2-5], and dissolution of major alloying components could pose significant problems for down stream piping [6]. In addition, concerns of Helium formation due to Ni transmutation prevented this alloy group to be used as fuel cladding. The corrosion resistant austenitic stainless steels (e.g. 316L) are found to be susceptible to localized corrosion such as pitting, intergranular attack and stress corrosion cracking (SCC) [7]."

Jan 1, 2012

By Núbia Suely Silva Santos, Alexandre da Silva Crespo, Frederico Muylaert Margem, Sergio Neves Monteiro, Anderson de Paula Barbosa, Michel Picanço Oliveira

"Environmental considerations in addition to technical, economical and societal benefits are increasingly promoting the substitution of natural fibers for glass fiber in polymer matrix composites. However, natural fibers are heterogeneous in their dimensions, specially the cross section, which plays an important role in their mechanical strength. The fibers extracted from the petiole of the buriti palm tree is a relatively unknown but promising natural fiber for composite reinforcement. In this work, a statistical analysis of the density of buriti petiole fibers using the Weibull methodology was performed. An attempt to correlate the fiber density with the diameter, precisely measured by means of a profile projector, was carried out. The results revealed an inverse dependence between the buriti petiole fiber diameter and corresponding density. Fracture tip observation by SEM suggested a possible mechanism that could justify this inverse correlation.INTRODUTIONIn the past decade polymer composites reinforced with natural fibers obtained from cellulose-based plants, known as lignocellulosic fibers, have been applied in several engineering sectors, specially the automobile industry as both interior and outside component [1-4].Environmental benefits as well as economical, social, and technical advantages are actually promoting the substitution of these lignocellulosic for the traditional glass fiber in polymer matrix composites [5]. Today several lignocellulosic fiber are being extensively investigated [6-11] and considered for reinforcement of polymer composites. Some relatively unknown lignocellulosic fiber with reinforcement potential, however, still need to be characterized aiming at future application in composites. This is the case of the fibers stripped of from the petiole of the buriti palm tree, which is endemic in the central and northern regions of South America [12,13]. Preliminary works on the possibility of using the buriti petiole fibers as composite reinforcement, has shown favorable results [14,15]."

Jan 1, 2012

By Gaifeng Xue, Jingxuan Zhou, Shangchao Liu

"Both COD and TOC can characterize organic pollution of coking wastewater. In theory, there is a linear correlation between these two indicators. After continuous monitoring TOC and COD of coking waste water, linear regression relationship between of these to indicators was studied with the use of mathematical statistics. And conversion equation between these two indicators was established, and using t-test method for significance testing. The results showed that the linear relationship of COD and TOC was significant. Also interval estimation of equation slope and intercept were given in the condition of 95% confidence level. A linear regression equation established can be used to indirectly convert TOC to COD with high precision and accuracy.IntroductionBoth chemical oxygen demand (COD) and total organic carbon (TOC) are measure of the degree of characterization for organic pollution of water bodies. The current COD standard analytical methods is Potassium dichromate titration method [1] . there are some disadvantages in this method, such as only part of organic matter in the water bodies being oxidated, the refluxed steps, a long time needed for each measurement, high cost. It is the most important that sulfuric acid silver and mercury sulfate reagents used in the measurement may easily lead to secondary pollution. In contrast, the measurement of TOC is by the method of combustion or Photocatalytic Oxidation. The result could be easily got from the instrument. There are some advantages in this way, such as easy operation, short time and little expenses for each measurement and no secondary pollution 121• In addition, the measurement of TOC has higher degree of precision and accuracy than the measurement of COD both in the determination of calibration standards and actual samples. The meaning and contrast of TOC and COD are listed in the table 1."

Jan 1, 2013

By Chenhui Liu, Ka-ma Huang, Hong-ying Xia, Bingguo Liu, Hua Chen, Jinhui Peng, Libo Zhang

"The rising popularity of microwave heating in mineral processing has fuelled the need for knowledge concerning dielectric properties of minerals. Dielectric property and microwave absorption property of anthracite were measured over a temperature range of 20-100°C at 2.45GHz by using an open-ended coaxial sensor measurement system. The results show that the dielectric constant, loss factor and loss tangent increase with temperature rising at 2.45GHz. Microwave absorption properties of anthracite are highly dependent on temperature and frequency. At frequency of 2.45GHz frequency used in microwave metallurgy, anthracite is suitable for reducing agent to achieve fast elevation of temperature then returning to original state. The research will be helpful in explaining the thermal running of microwave dielectric heating the anthracite.IntroductionThe application of microwave heating in minerals processing and treatment has recently attracted great interest from the metallurgical industry. Compared with conventional heating methods, the advantages of microwave heating include rapid and selective heating, uniform distribution, high efficiency, fast on and off switching as well as flexible and modular design[l-3]. As a result of these advantages, microwave heating has been applied in a variety of mineral processing and extractive metallurgy, such as microwave-assisted ore grinding, microwave heating for carbothermic reduction and acid leaching of ilmenite ore, microwave drying, microwave-assisted roasting and smelting of sulfide concentrate, microwave-assisted spent carbon regeneration and microwave-assisted waste management [ 4-6]. Though the application of microwave heating in the metallurgical industry is promising, further studies on the interaction between microwave radiation and minerals and its effects are highly desired to develop innovative techniques for minerals processing and ore treatment using microwave heating [7]."

Jan 1, 2013

By B. C. Curson

A comprehensive simulation of .the gas handling system in BHP Copper's San Manuel smelter was developed using AFT Fathom software, with the objective of minimizing SO2 emissions while maximizing smelter throughput. Once verified with plant data, the simulation quickly revealed' the complex interactions occurring between individual converters and the flash furnace. The increased understanding provided by the simulation allowed novel, counter-intuitive control strategies to be developed and tested successfully.

Jan 1, 1999

By Kent D. Peaslee, Lifeng Zhang, Edith Martinez, Yufeng Wang

The current study investigated the multiphase fluid flow, heat transfer, solidification of the steel, and the motion and entrapment of inclusions during the centrifugal casting process using FLUENT software. User-defined functions (UDFs) were developed to add velocity with a value related to the rotation speed and radial distance to the solidified steel, to exert a centrifugal force to the motion of inclusions, and to add the entrapment condition of inclusions at the solidifying shell and export the entrapment locations of the inclusion. The calculation shows that there are two peaks of inclusions along the thickness of the produced tube: one at close to outer surface and another one close to the inner surface of the tube. With a larger rotation speed, inclusions tend to be entrapped more towards the inner surface. The calculation agrees well with the industrial measurements.

Jan 1, 2012

By A. V. Tarasov

Technology has been developed for production of elemental sulphur from off-gas from autogenous smelting processes based on reduction of sulphur dioxide with natural gas with subsequent treatment of reduced gas containing hydrogen sulfide by the Klaus method. This technology has been applied on a commercial scale at the copper smelter of the Norilsk Mining and Metallurgical Complex for treatment of off-gas from the Vanyukov smelting process (PV). In the course of further improvement of the technology a catalytic version of the process has been developed based on the use of a catalyst at the reduction stage, which permits a decrease in the natural gas requirement by 25% to 30%.

Jan 1, 2006

By J. G. Peacey, P. Hancock, R. -Q. Li

A pyrometallurgical process for the direct recovery of zinc from zinc concentrates and zinc/iron residues has been proposed and tested extensively by Noranda. The process consists of smelting bone-dry zinc containing materials (sulfide concentrates and secondary zinc/iron materials) in a molten iron oxysulfide bath to volatilize metallic zinc into a SC^-free offgas. Sulfur contained in the feed materials is fixed as an iron oxysulfide matte for disposal. Thus, this process not only is capable of treating zinc sulfide concentrates and secondary zinc materials simultaneously, but also eliminates the need of sulfuric acid production. Detailed thermodynamic analysis and experimental test work are described in this paper.

Jan 1, 2000

By Levent Özmen

Colemanite is a mineral containing varying amount of boron that is found in abundance in Turkey. It has a good possibility to be used as a flux in iron and steel industry. In this study a review of the use of colemanite, as a flux agent in steel production has been carried out and various related aspects such as its influence in metal-slag reactions, solubility of lime and magnesia in the slag are discussed along its performance in several points of views including its technical and environmental usage characteristics. Positive and negative factors of using this material as a flux are also underlined.

Jan 1, 2006

By Ioannis Paspaliaris, Dimitrios I. Gerogiorgis, Dimitrios Panias

"Red mud fiberization is a process with remarkable potential, alleviating environmental pressure by transforming an aluminum by-product into mineral wool, thus to various marketable products. A promising mineral wool process is molten slag fiberization via an impinging air jet, which avoids mechanical wear and rotating parts. The molten slag which remains after pig iron casting flows out of a heated ladle orifice at a high temperature (1600 °C) and adjustable flowrate, and forms a free-falling vertical jet which visibly radiates its excessive heat: at a given distance, a high-velocity impinging air jet meets the vertical melt jet perpendicularly (or at an angle), inducing intensive droplet generation, subsequent fiber elongation, collection and processing.This paper focuses on high-fidelity CFD modeling of the molten jet flow under external cooling: the model encompasses all physicochemical phenomena (melt laminar flow, radiative cooling) and considers several temperature-dependent slag transport properties in order to understand which operational degrees of freedom (manipulated variables) are useful to process optimization."

Jan 1, 2012

By Xin Wang, Hongmin Zhu, Shuqiang Jiao

"The behavior of electrochemically depositing silicon in a molten high-melting-point fluoride electrolyte was studied at 1300 °C. The cathodic product was characterized by XRD, SEM and EDS. Though the analysis of structure and composition of deposition, it could certify that silicon deposited on the Mo rod and alloyed with molybdenum. A series of tests had been performed on the cathodic behavior of Si4+ ions in BaF 2-CaF 2-Na2S iF 6 molten salt. The influence of electrochemical parameters on the cathodic deposition of silicon was also investigated. The electrochemical behavior of Si4+ ions in applied fluoride melts was observed to proceed according to one-step reaction.IntroductionGreenhouse warming has been a serious global issue. lt is increasingly urgent for clean and renewable energy. Effective utilization of clean and inexhaustible solar energy has become very important. Solar cell (especially poly-Si solar cell) production has significantly increased this decade, as there is a growing demand for clean energy. Since the early 1980s, the annual growth of the photovoltaic (PY) solar cell industry is more than 30%. More than 90% of the annual solar cell production is based on crystalline silicon wafers. This rapid growth leads to a shortage of silicon of the adequate quality and price for the continued growth of this industry [I , 2J. The most conunonly used technology to produce silicon is the so-called Siemens process. This technology, involves the forming of gaseous Si compounds such as trichlorosilane (SiHCli) or silane (SiH4) with subsequent thermal decomposition of these back to Si. This technology is associated with transformations from solid to gas, and then back to solid phase, which lead to high irreversible thermodynamic losses and subsequent high energy consumption, the energy cost being around 200kWh/kg Si [3l_ The purity of the material from this process is very high (9 to 11 N). In general, what is needed for solar cell purposes are reported to require 4 to 6 N quality. To promote continued growth of the silicon-based PY industry, there is need for a low-energy silicon production process which can produce large amounts of silicon with an acceptable quality and a lower price particularly."

Jan 1, 2012

By Jari Aromaa, Antti Kekki, Olof Forsén

"The deposition of copper on inert substrate depends on the number of active sites that will react at certain overpotential. The critical overpotential depends on surface morphology, surface film resistance and additives on cathode surface. The effects of surface properties on copper nucleation and growth rates were studied for used stainless steel blanks from several tankhouses. The surfaces of the blanks were characterized with electrochemical and mechanical methods. Electrochemical deposition tests were done at current density of 300 A/m2 for 10, 30 and 60 seconds. The nucleation density and copper coverage were estimated using image analysis. The surface film resistance did not correlate with copper growth. Increasing surface roughness correlated with lower copper growth.IntroductionStainless steel cathode blanks in copper electrorefming are usually made of AISI 3 I6L type steel. They have a typical lifetime over 10 years. During use the surface will collect deposits and become rough due to wear and corrosion. These factors can affect the nucleation and growth of copper. The nucleation and deposition of copper on inert substrate depends on the number of active sites that will react at certain overpotential. The critical overpotential can depend on surface film resistance, surface morphology, and additives adsorbed on cathode surface.The deposition potential of metallic ions on a foreign substrate is usually higher than the deposition potential on the electrode made of the same metal due to crystallographic substrate/metal misfit [I]. If the substrate has traces of the depositing metal they will be preferential growth sites. For a smooth deposit a large number of simultaneous nuclei is necessary. However, excessive nucleation density can lead to porous deposits [2]. Surface films of good conductivity are needed for dense nucleation and small nuclei. On cathode blanks the number of active sites increases with increasing surface film conductivity [3-5] and/or surface film porosity [6]. On AISI 3 I6 L stainless steel a more resistive oxide has been found to limit favourable sites for copper nucleation and more conductive film promoted high-density copper nucleation [7]. Also Urda-Kiel et al. have concluded that thicker oxide layers on AISI 304 stainless steel resulted in lower nucleation [8]. Increase in overpotential or current density activates more and more of the potential nucleation sites and this can be seen as higher number of nuclei [9] or smaller average distance between nuclei [10]."

Jan 1, 2012

By S. S. Babu, T. Hong, T. DebRoy, S. A. David

"Oxide inclusions form in welds because of deoxidation reactions in the weld pool. These inclusions control the weld microstructure development. Thermodynamic and kinetic calculation of oxidation reaction can describe inclusion characteristics such as number density, size, and composition. Experimental work has shown that fluid-flow velocity gradients in the weld pool can accelerate inclusion growth by collision and coalescence. Moreover, fluid flow in welds can transport inclusions to different temperature regions that may lead to repeated dissolution and growth of inclusions. These phenomena are being studied with the help of computational coupled heat transfer, fluid-flow, thermodynamic, and kinetic models. The results show that the inclusion formation in steel welds can be described as a function of the welding processes, process parameters, and steel composition.IntroductionThe relationship between inclusions and formation of a high-toughness phase, namely acicular ferrite in low-alloy steel welds, is well known (1-4). Past research has focused on maximizing acicular ferrite amount in welds by controlling welding processes, process variables, and welding consumable parameters. Research has shown that there is a complex interaction between inclusion characteristics, prior austenite grain size, and weld metal hardenability. In a low-alloy steel weld, the small addition of titanium lead to a change in the inclusion composition and resulted in a transition in the microstructure from bainitic to acicular ferrite [see Fig. I]. This in turn lead to the best combination of strength and toughness. This paper describes the inclusion formation in low-alloy steel welds."

Jan 1, 1999

By Katsuyasu Sugawara, Takuo Sugawara, Shin-ji Abe, Tadakazu Kagami

"In order to clarify the mechanism and to obtain the fundamental data for heavy metal recovery from an incinerator ash by chlorination, pure chemical reagents, zinc oxide and lead oxide or the fly ash blended with calcium chloride and silicon dioxide were heated up to 1000°C in a nitrogen stream. Thermogravimetric curves of the samples with the chlorinating reagents indicated that solid-liquid reactions accelerated the chlorination and release of metals from the solid phase. The formation of liquid phase of calcium chloride played an important role on effective recovery of zinc and lead at lower temperatures below 800 °C. Although zinc and lead could be decreased in the incinerator ash without chlorinating reagents, addition of chlorinating· reagents enables the removal of metals in high extent· at lower temperature.IntroductionFly ash is discharged about 3,000 tons/day (about 110 million tons/year) from incinerators of municipal solid waste in Japan and mostly fly ash is disposed in landfills. Fly ash includes heavy metals e.g. zinc and lead. Since untreated fly ash caused hazardous leaching problems, Waste Disposal and Public Cleaning Law was revised in 1992, fly ash being designated 'specially controlled' general waste. Fly ash must be disposed by the following suitable, intermediate four methods: [I] Cement- Solidified Method, [2] Immobilized Chemicals Method, [3] Melting Solidified Method, [4] Acid Leaching Method, permitted by the Ministry of Health and Welfare, Japan."

Jan 1, 2000

By Bowen Li, Jiann-Yang Hwang, Mingsheng He, Huaguang Wang

Kyanite is one of the major high-alumina minerals for producing refractory ceramics. At high temperature, kyanite can be decomposed into mullite and amorphous silica. This change is an irreversible decomposition and provides potentials for fiber reinforcement of ceramic matrix. In this study, kyanite powder was compressed into a cylinder green body of ceramic and heated at 1150–1450 °C.The phase transformation of kyanite and sinterability were investigated by X-ray diffraction and scanning electron microscopy. The results showed that the phase transformation of kyanite started at 1150 °C when rising the temperature. At 1350 °C, kyanite is completely converted into mullite and silica. The compressive strength of the ceramics reached 73.3–134.8 MPa, while the bulk density was 1.95–2.47 g/cm3. The microstructure indicated the correspondence of the compressive strength to mullitization degree of kyanite.

Mar 1, 2017

By I. Moscoso, R. Padilla, M. C. Ruiz

Antimony and arsenic are impurities in copper concentrates found normally as stibnite (Sb2S3), tetrahedrite (Cu12Sb4S13) and enargite (Cu3AsS4). When copper concentrates contain appreciable amounts of As and Sb, they must be removed before smelting to avoid environmental pollution. Oxidizing volatilization roasting at 500–700 °C has been used to eliminate these impurities. However, only a fraction of Sb volatilizes in those conditions; thus, a more effective process to eliminate antimony from concentrates is needed. In this study, the chloridizing roasting of Sb2S3 using CaCl2–O2 was investigated to remove the antimony from concentrates. XRD analysis of calcines indicated that the overall reaction could be written as: Sb2S3 þ3CaCl2 þ6O2 ¼ 2SbCl3 þ3CaSO4 Temperature and oxygen partial pressure have a significant effect on the rate of reaction. An estimated conversion of about 90% was obtained at 750 °C, 5.4% oxygen in 20 min. High oxygen concentrations arrest the advance of the reaction forming various antimony oxides including Sb6O13, Ca5Sb5O17 and Sb2O4.

Mar 1, 2017

By Ali Kucuk, Bekir Karasu, Keriman Karaveli Pekkan

"Zircon (zirconium silicate) is the main opacifier of glossy, opaque, white colored, frit-based wall tile glazes. However, zirconia containing frits employed in the preparation of these glazes increase the production cost and therefore, limit zircon usage as a raw material at industrial scale. With the present study, it was searched whether borax solid wastes could be evaluated as a component in the starting relevant frit recipes. The wastes were obtained from Eti Maden Kirka Boron Company of Turkiye. Frit production, glaze preparation, application, and fast single-firing of glazed wall tiles were conducted under laboratory working conditions in Anadolu University, Department of Materials Science and Engineering laboratories. Beside standard tests applied to the final glazed wall tiles, color and gloss analyses of the fired glazes were conducted with a spectrophoto-meter and a gloss-meter. Characterization of these newly produced glass-ceramic glazes was made by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) techniques. IntroductionFrits are the indispensable constituents of most industrial glazes which mature at temperatures below 1150 °C [1]. In the traditional opaque glazes used in wall tile industry, opacity usually originates through hardening of glass matrix by adding high amounts of zirconia containing frits into the glaze batch [2]. Nowadays, researches point out that certain type of glass-ceramic layers can be alternatively employed as tile coatings lowering the use of zirconia containing expensive opaque frits. A rather high crystallization capacity of glass- ceramic glazes due to zirconia presence in glass network makes them suitable candidate as a glaze coating with a desirable micro-structure. One of the best methods to obtain an opaque glaze surface is to induce a crystal phase in the coating, whose refractive index differs significantly from that of the glassy matrix. The opacity of such coating is determined by the diffusion, refraction and reflection of light through the layer containing emerging crystals, and the degree of opacity mainly depends on the size and quantity of crystals. The development of glazes not consisting of expensive or toxic components is of special interest [3]."

Jan 1, 2008

By Khoo Khyou Pin, Yoshiyuki Funaki, Hirotsugu Takeuchi, Ryoichi Urao, Naotatsu Asahi

"Steel is used to be ion carburized with mixing gas of methane and hydrogen. In carburizing, carbon in the methane decomposes and deposits on the steel by plasma, so methane gas flow may influence on ion carburizing of the steel. An apparatus in which works can transfer preheating, ion-carburizing and diffusion treating zones continuously was made for effective carburizing of steel. The gases were flown into above three zones with three different gas inlets. The hardness and microstructure of the works were investigated after ion carburizing and quenching. The steel is carburized deeper near the carburizing gas flow nozzle of the inlet than far from the nozzle. Hard surface layer fom1ed by quenching of ion-carburized steel.IntroductionGas carburizing is used for a surface hardening treatment which decreases fatigue and wear of the industrial parts used in automobile, machines etc. Ion and vacuum carburizing have been developed recently and applied to some industrial parts of restrictive purposes. The ion carburizing treatment which uses hollow cathode discharge (HCD ion-carburizing) is superior in energy saving, resource saving, environmental cleanness to the other carburizing treatment. Specially, carburizing energy can be saved in HCD ion-carburizing, because highly heated zone can be restricted in the range between work and subsidiary cathode where hollow cathode discharge arises, and the work is carburized in shorter tin1e in HCD ion carburizing method than other carburizing methods. Three treatments of preheating, carburizing methods and carbon potential controlling by hollow cathode discharge tried to be carried out in one continuous transferring series to carburize works more effectively, so the HCD ion-carburizing apparatus with continuous transferring system was made and gears of works were HCD ion-carburized in continuous transferring. The works were rotated themselves to get homogeneous carburizing by continuous transferring in glow of hollow cathode discharge."

Jan 1, 2000

By Shigem Kuramoto

Pure copper is known to exhibit intermediate temperature embrittlement when it is deformed at a slow strain rate, and a small addition of zinc suppresses this embrittlement. In the present study, the relation between zinc addition and hydrogen behavior was taken into account since the impurity hydrogen is believed to deteriorate the ductility at intermediate temperatures. Pure copper and Cu-l mass % Zn alloy specimens are prepared by melting in argon and in vacuum, so that a comparison can be made between the specimens with normal hydrogen content and those with' less hydrogen content. Tensile tests are performed at temperatures ranging from room temperature to 600 "C, and hydrogen behavior is analyzed using a newly developed testing machine that can detect gas evolution from the specimens during deformation and fracture in ultra high vacuum. The small addition of zinc to pure copper decreases hydrogen content, leading to the improved ductility at intermediate temperatures. In addition, the samples of both pure copper and Cu-1%Zn melted in vacuum exhibited higher ductility at intermediate temperatures than those melted in argon atmosphere, which is attributed to reduced hydrogen content.

Jan 1, 1998