Search Documents

Refractory gold concentrates often contain sub-microscopic gold that is encapsulated within the crystal matrix of iron sulphide minerals such as pyrite, pyrrhotite and arsenopyrite. To recover the gold, the host mineral must generally be broken down chemically, by oxidative processes such as roasting, pressure oxidation or bacterial leaching, which expose the gold for subsequent recovery by leaching in cyanide solution. The focus of attention in these pre-treatment processes is usually the oxidation of the sulphides to elemental sulphur, sulphur dioxide gas or sulphate ions. Less attention is paid to the deportment of iron and the changes in its oxidation state, although this can have a profound effect on gold and silver liberation, as well as down stream operating costs. Iron sulphide minerals break down completely during pressure oxidation, and dissolve in the sulphuric acid solution that is generated from oxidation of the sulphides. This liberates the tiny gold particles that were originally trapped in the sulphide crystals, and gold recovery during subsequent cyanidation is usually very high (>95%). Iron goes into solution in the oxidation process, initially as ferrous sulphate, but this is rapidly oxidized to ferric sulphate, which then hydrolyzes and re-precipitates. The form of the precipitate varies depending on the operating conditions in the autoclave and the presence of certain metal cations. When the acidity in the autoclave is quite low (<20 g/L H2SO4) and the temperature is high (>200OC) the formation of hematite is favoured. When the acidity is high (>20 g/L H2SO4) and the temperature is relatively low (160 to 200OC), the formation of basic iron sulphate is favoured. If the ore or the leach solution contain significant levels of certain cations (such as Na+, K+, NH4+, Ag+ or Pb2+) and the acidity is high (>20 g/L H2SO4), jarosite compounds are favoured. Hematite is the desired iron product in the autoclave discharge, for both metallurgical and environmental reasons, but it is difficult to operate an autoclave under the conditions required for effective liberation of gold without converting some of the iron to basic iron sulphate and/or jarosite. These compounds fall into a category of iron compounds known generically as iron hydroxy sulphates, all of which can cause significant processing and environmental problems in the downstream gold process. This paper deals specifically with basic iron sulphate; the conditions under which it is formed in an autoclave, the problems that are caused by its presence in the feed to a cyanidation plant, and possible remedial strategies that can be adopted, both in the autoclave and downstream.

Jan 1, 2010

By M. Ishaq, J. Rosami, J. Brune, E. Sidrow, C. Tsai, S. Slouka

Respirable rock dust poses serious long-term health effects to workers in mining and tunneling underground hard rock environments. When inhaled, respirable silica particles commonly found in quartz and other minerals will scar sensitive lung tissue and cause irreversible lung diseases. Characteristics such as concentration, type of mineral, particle size, and particle shape inhaled can harm workers to various extents. Therefore, this study characterizes rock dust particles less than 100µm in aerodynamic diameter that are released from cutting hard rock in the underground mining environment. In this study, laboratory full scale cutting tests on samples of potash rock were performed with radial picks to generate dust. Three stages of pick wear were tested: new, moderately worn, and severely worn. Comparisons between different stages of pick wear to dust concentration, size distribution, and particle shape characteristics are drawn from this study to start determining the scenarios when the released airborne dusts become potentially most hazardous for workers. Although further testing needs to be conducted to make viable conclusions, the moderately worn pick, or the pick with the most blunt tip, in these experiments are potentially the most dangerous. The blunt pick tip released the highest concentration of dust and generated particle shapes with the highest aspect ratio compared to the other two picks. The preliminary results of this study allow for the further development of optimum bit management and maintenance systems to control the exposure of respirable dust to mine workers.

Mar 2, 2022

By C. Flores

The most common experimental approach of studying one variable at a time while holding all others constant is extremely inefficient. Use of statistical methods enables engineers and scientists to obtain meaningful information with the fewest experiments, reducing cost and wasted effort. In particular, the Taguchi method can be more efficient than traditional full factorial experiment designs, as it can study more variables with fewer nuts, and it is more robust against process "noise." Taguchi designs are also simple to formulate and the results can be analyzed by simple PC spreadsheets. The role and benefits of using the Taguchi method in experiments to develop and optimize processes is discussed.

Jan 1, 1998

By David A. Campbell

There has been a long history of ironmaking on the North East coast of England centered around the River Tees. The industry developed here because of the availability of good coking coals to the North in Co. Durham, and the discovery in 1851 of ironstone in the nearby Cleveland Hills, South of the .River. Cleveland ironstone is relatively poor in quality, with an iron content not exceeding h% and high proportion of sulphur and phosphorous. The iron exists in chemical association with alumina and silica, and physical beneficiation processes involve a serious loss in iron unless the upgrading is limited, when the economics of the process become doubtful. Over the years, richer foreign ores have replaced the local ironstone, and the last operating mine was closed in 1964.

Jan 1, 1982

By James D. Cooper

Technologic advances in materials utilization during the past two decades have brought is a long way toward the point where we can make the products we need from the materials we have readily available. Notable examples are the synthesis of diamond, zeolites, quartz crystal, mullite, and mica, and the development of phosphate bonded tale. Two of these--zeolites and mullite--involve the use of clays. There is little reason to doubt that equally important advances will be realized in the next decade, and that clays will play an important role in the developing materials technology. Indeed, the stage is already set for many of them. This discussion is concerned primarily with the high quality, relatively high priced clays, kaolin, bentonite, fuller&apos;s earth and ball clay. The first three have enjoyed demand growth rates over the past two decades which on the average exceeded the growth rate for the economy as a whole. There are indications that demand for ball clay will be growing at a faster rate in the future.

Jan 1, 1970

By G. P. Hand

The purpose of this paper is to bring to your attention the various kinds of high performance graphites available today, their characteristics and possible applications. These materials are products of a proprietary high temperature technology developed by Superior Graphite Company. We feel we have only begun to tap the potential of this technology and the utilization of the resulting products. During the course of the paper, we shall investigate high purity, high performance graphites made from raw materials such as mined natural graphites, synthetic graphites and petroleum derivatives. We shall define their characteristics and resulting benefits to current applications, along with applications currently under development. It is our desire to stimulate speculation and development of current high performance graphites and their applications as well as ideas for new high performance products and applications. First, a little background about the process. The technology was developed through a concentrated R&D effort which culminated in 1976 in the construction of a unique furnace capable of continuously processing tonnage quantities of granular carbons at temperatures in excess of 2,500 degrees C. This process is capable of refining various carbonaceous raw materials, including natural graphites, to levels of purity and consistency that were previously unattainable in commercial quantities. Carbon contents in excess of 99.9% are currently being produced on a continuous flow-through basis. Since beginning operation in 1977, this plant, located in Hopkinsville, KY, has been expanded in stages to its present capacity of producing over 45,000 tons of purified graphites and graphitic carbons per year. In addition to the purification process, the technology used allows the introduction of selected elements into the carbon/graphite structure to provide additional benefits. Elements of interest include boron, silicon, copper, iron and rare earths. The characteristics of and applications for some of these products will be discussed later.

Jan 1, 1990

By Jr. Raleigh

In a cooperative agreement between the U.S. Bureau of Mines and the U.S. Department of Energy, laboratory column-flotation tests were conducted to evaluate fluorosurfactants as selective fine coal flotation collectors. A Middle Kittaning seam coal responded to flotation with both anionic and nonionic fluorosurfactants. These fluorosurfactants were no more selective than MIBC alone. However, for increasing coal yields, nonionic fluorosurfactant systems did not increase total sulfur and ash contents as sharply as MIBC systems. Flotation selectivity also improved slightly when a combined anionic fluorosurfactant-MIBC system was used in acidic pulps (pH < 3.6). While the fluorosurfactants examined will not likely have direct application in current coal flotation practice, other fluorosurfactant systems could eventually prove beneficial for floating fine coals.

Jan 1, 1990

By Keith G. Wallace, K. M. (Chris) Chmura, Kirk H. McDaniel

The Waste Isolation Pilot Plant (WIPP) performed a feasibility analysis for the purpose of either modifying, supplementing, or replacing its two main mine fans. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) fa¬cility designed to demonstrate the permanent, safe disposal of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Since the centrifugal fans were installed in 1988, multiple op¬erational and performance concerns have been identified. A com¬prehensive engineering study was conducted in 1995 to: 1) Qualify and quantify operational concerns, 2) Evaluate possible alternatives, and 3) Recommend an optimum solution. Multiple system modification and/or replacement scenarios were evaluated with associated cost estimates developed. The study considered replacement with either centrifugal or axial fans. Multiple fan duties are required at the WIPP. Therefore, Variable Frequency Drives and Inlet Vane Controls (IVC) were investigated for centrifugal fans. In-flight adjustable blades were investigated for axial fans. The study indicated that replacing the existing system with two double-width, double-inlet centrifugal fans equipped with IVCs was the best choice. This alternative provided the most desirable combination of: 1) ensuring the required operational readiness, and 2) improving system performance. The WIPP is currently planning to replace the first fan in 1997.

Jan 1, 1997

By Utku Gumus, Ertan Bostanci, Hanifi Copur, Ahmet Rüfai Bilgin, Ugur Altay

"Field observations on replacements of 12-inch constant cross-section double disc cutters in Tuzla Wastewater Tunnel excavated by an EPB TBM with 3.151 mm excavation diameter excavating hard rock are summarized. Cutter life is correlated to rock’s uniaxial compressive strength and Cerchar abrasivity index, and TBM operational parameters. Number of cutter replacements, average cutter replacement rates and types of cutter damages are summarized. The relationships between cutter life and rock properties and TBM operational parameters are analyzed by single variable regression method. Detailed analysis between chainages 1+200 and 1+982 km indicates that average cutter consumption rate is 35.7 m3/replacement (4.6 m/replacement). Cerchar abrasivity index and uniaxial compressive strength does not indicate any meaningful relationship with cutter life. Penetration per revolution and field specific energy might be used for predicting lives of constant cross-section double disc cutters. However, additional data is required to generalize the findings of this study. INTRODUCTION Cutter life / replacement and/or consumption rates in terms of cutter cost and replacement time loses is one of the most important parameters affecting excavation performance of mechanical excavators, especially of TBMs used very widely and equipped with usually disc cutters. Predicting cutter cost is a very important task in especially feasibility stage of tunneling projects. Basic parameters affecting cutter life can be classified into 3 general groups as geological and geotechnical, excavation machine (TBM) related, and operational parameters (Bilgin et al., 2013). The geological and geotechnical parameters are the most dominant ones among them. The machine related parameters should be arranged in accordance with the expected geological and geotechnical conditions for the best TBM excavation performance and minimum cost."

Jan 1, 2016

By Jr. Hawk

The power generation industry may be required to reduce CO2 emissions if regulations related to global climate change are enacted. Coal-fired generation, which emits 82% of the power sector CO2, would be a likely target for CO2 reduction. Compliance with the Kyoto protocol will require a 30% reduction from the projected year 2012 emission level even with moderate load growth. This paper describes an analysis of power industry CO2 reduction options and their costs to assess how a generator would make compliance decisions under a mandatory CO2 emissions reduction program. Carbon sequestration, fuel switching and new plant construction are considered.

Jan 1, 1999

By C. E. Capes

The spherical agglomeration process provides an attractive method for the cleaning and recovery of fine coals in the form of compact oil-bonded pellets. In treating a washery effluent containing 50% minus 20 micron material by this technique, the slurry was first mixed under vigorous agitation with oil to deash and dewater the fine coal. The flocculated coal pulp was then formed into larger agglomerates on a modified balling disc. The operation of a semi-pilot scale process is described and an analysis of some of the operating and system variables is given. A semi-theoretical expression to predict the final agglomerate size under various conditions is derived and compared with the experimental data. Coal producers are faced with a growing requirement to clean and recover fine mesh coals. Greater mechanization of the extractive and preparation processes has resulted in finer-sized products containing larger quantities of associated foreign matter and preparation plant effluents contain quantities of fine coals which are potentially valuable. These losses will probably increase with the expansion of production and will require the development of effective disposal and utilization processes under pressure of the lack of adequate disposal areas, the enforcement of air and stream pollution laws, and the economic need to obtain the maximum yield of salable product(1)

Jan 1, 1970

By L. L. Oriard

The author describes three case histories of fracture-control blasting demonstrations. This is a technique in which the walls of blast holes are scribed or notched in order to enhance the development of blast_induced fractures, and to control their direction. One demonstration was that of a tunneling application in a rock that was generally competent but strongly foliated, hence strongly anisotropic. P second test was conducted for perimeter blasting of a structural excavation in a massively jointed limestone. A third field test was conducted for tunneling through an old concrete structure. Increased applications are envisioned with new tool modifications being developed at the University of Maryland.

Jan 1, 1981

By L. S. Gertsch, M. Z. Abu Bakar

Linear cutting tests of a porous sandstone with a radial drag pick show that saturation of rock with water can increase the specific energy of fragmentation. This appears to be due, in this case, to a saturation-induced increase in the forces acting on the cutting tool without a concomitant increase of the fragmented volume. The mechanisms of this reaction are explored by examining various responses of the parameters controlled and induced during the linear cutting tests, such as cut spacing, cutter penetration, three-dimensional forces and muck production. A program of load-indentation testing is underway to evaluate the permeability threshold of this behavior. These findings are opposite from those made when the same rock is cut with a constant cross-section disc cutter reported elsewhere (Abu Bakar and Gertsch, 2011). Such results highlight the effects of different cutting tool designs, and indicate the need for a well-coordinated program of research to support effective excavator design and selection.

Jan 1, 2012

By S. Veeramasuneni

The sign of the surface charge for alkali halides in their saturated brines has been established from non equilibrium electrophoresis measurements and on this basis the flotation response of alkali halides was explained based on the adsorption of oppositely charged collector colloids by heterocoagulation. These surface charge results for alkali halides are generally as expected from simplified lattice ion hydration theory with some exceptions, specifically LiF, KCI, NaCl, KBr, RbBr, KI, and Rbl .The presence of natural oxygen defect states in the crystal lattice and the inaccuracies involved in the gaseous ion hydration free energy values used appear, in past, to be responsible for these deviations. The presence of natural oxygen defect states in KCI, KBr, RbBr, and Rbl as characterized by UV Nis absorption, was found to account for their anomalous surface charge. Further, other positively charged alkali halides, LiF, NaCl and KI, were found to be free of oxygen defect states. Nevertheless, oxygen defects can be created in these alkali halides to make them negatively charged and has been demonstrated for NaCl. Such negatively charged NaCl can be readily floated with positively charged amine collector colloids thus confirming the surface charge/collector colloid adsorption theory.

Jan 1, 1996

By J. M. D. Wilson

The literature relating to binders in iron ore pelletizing is reviewed from the point of view of their established or proposed bonding mechanisms in green and dry pellets.

Jan 1, 1981

By L. A. Khan

This paper first discusses the physicochemical cleaning methods used to process fines followed by an analysis of the subprocesses of froth flotation and the adverse effects of slimes and particle oxidation. These subprocesses include the phenomena of interception, contact, adhesion and levitation. Preventive and corrective measures to combat the generation of fines and their effects are suggested. Preventive measures include controlled grinding, limited liberation, flotation at coarser sizes. Means of preventing oxidation and/or removing oxidation products are a1 so discussed. Corrective measure to increase recovery include intensive aeration, aggregation of particles, intensive mixing, increased retention time, and reduction of detachment. Measures leading to improves selectivity involve means to reduce slime coating, achieve selective mineralization of bubbles and minimize entrapment.

Jan 1, 1986

By K. N. Han

Coal is becoming increasingly important as a major energy source in the face of the world&apos;s depleting energy mainly based on oil reserves. Coal is by far the most abundant fossil fuel both in the United States and abroad. Currently, because of increased mine mechanization, the fineness of preparation plant feed is increasing. Further, in the future as the grade of coal diminishes and the sulfur content increases, upgrading preparation of coal is very important. Because the density of coal is less than that of rock materials that occur as impurities, coal is separated from such waste largely by gravity-controlled processes for particle size between 5 inches and 28 mesh. If the size of coal particles is below 28 mesh, froth flotation is a good method for upgrading fine coal. Previously, numerous investigators have tried to upgrade coal values by froth flotation(1-16) and have achieved moderate success. However, the recovery and grade of coals in the concentrates are not always satisfactory, especially when the particle size is small. In general, when the size of coal is below 100 mesh, the above methods suffer from poor grade and low recovery. The reason for this is that as size decreases, the effects of gravity diminish, and other forces take effect.

Jan 1, 1985

By S. R. Titley

Results of regional analyses of precious metal habits in Arizona ores lead to interpretations of a fundamental ore control related to geographic location that corresponds with crustal contrasts. Measurements of isotopic and trace element characteristics of Laramide ore-related intrusions lead to interpretations of crustal derivation of apparent ore-related magmas. Interpreted regionally, the numerous kinds of Laramide ores, which include porphyry copper deposits of this southern cordilleran region appear to be phenomena of a specific crustal lithology characterized by a basement of Proterozoic turbidites and (an interpreted) lower crust of amphibolite. This association with a specific basement terrane may be extended in principle from the United states into Mexico where faulted offsets of this basement are similarly favorable to formation of Laramide porphyry ores -to the exclusion of adjacent terranes. Whereas plate tectonic mechanisms may have triggered evolution of these ores, it is hypothesized here that crustal setting and crustal composition are more profound influences of metallogenesis.

Jan 1, 1992

By R. S. Kinasevich

As part of other work related to the studies of kinetic factors that influence the flotation of specific sulphide minerals, specially designed kinetic flotation experiments at Cominco included work done on -65 + 100 mesh and -100 + 150 mesh, high purity galena. The flotation collector used was sodium isopropyl xanthate containing radioactive sulphur-35. Radiation monitoring of the galena fractions from stage flotation tests indicated that the adsorbed radioactive xanthate was uniformly distributed among the floated fractions and the non-floated, or residual portion of the galena. This anomalous behaviour could not be correlated to changes in Seebeck coefficients, to lattice distortions, or to the nature of the mineral surface as revealed by infrared spectroscopy and by microscopic measurements.

Jan 1, 1970

By Eduardo Rojas, Pedro Landeros

El Teniente Mine expansion plans are currently under development and construction stages through an integrated project strategy that will allow the continuity of future mining. The deepest sector corresponds to Andes Norte Project that faced rockburst risks during tunneling in a completely different manner, implementing different actions for the mitigation of seismic hazard and seismic risk management, based on the following main aspects: rock mass preconditioning techniques such as destress blasting and hydraulic fracturing, improvement of rock support design with the inclusion of elements with higher energy dissipation capacities, use of mechanized equipment for the most critical activities in addition to re-entry protocols and improvements in geological, geomechanical and seismic data collection procedures to reduce the uncertainty of rock mass behavior. The current seismic risk management strategy integrates all of these elements and is the basis of construction methodologies in use, supporting the technical feasibility of tunneling in high-stress environments.

Apr 26, 2022