Search Documents

In this paper we present the results of preliminary investigations into the applicability of new laboratory scale tests for the prediction of operating gap and specific throughput in high pressure grinding rolls (HPGR). The work is a part of the CAMIRO HPGR research program being conducted at the University of British Columbia, which aims to develop a suite of small-scale tests and procedures for the selection and sizing of HPGRs. A focus of the presented study is to test sample types in terms of their terra-mechanics based characteristics and relate them to specific throughput and gap results from pilot HPGR testing on the same samples.

Jan 1, 2012

By Francis W. Gray

Introduction Extensive undersea coal-mining has developed on both the east and west coasts of Canada, and at this time some four million tons, or 25 per cent of the total output of Canadian coal, representing a pit-mouth value of $14,000,000 per annum, is coming from coal seams lying under the sea. Of the coal now being mined in Nova Scotia, 55 per cent comes from under the sea, and this proportion is likely to increase. The Province of Nova Scotia is at this date receiving in royalties paid upon coal ?removed from undersea areas a sum exceeding $400,000 per annum. The subject is, therefore, one of special interest to the Mining Society of Nova Scotia and the Canadian Institute of Mining & Metallurgy, and while this paper will deal chiefly with undersea coal-mining in Nova Scotia, an attempt has been made to summarize the development of mining practice in the winning of undersea coal in other parts of the world, with the hope that such a recital may assist in the assessment of local problems. The connection between the mining of coal under the sea and an insular or maritime geography is obvious in regard to Great Britain, Japan, Vancouver Island, Australia, and Cape Breton Island, and also in regard to the curious conformation of Chile; the tendency towards growth of a mercantile marine and naval eminence is equally obvious where coal is mined at tidewater. But, there is the further and less favourable significance that the mining of coal under the sea is associated with poverty rather than with abundance of coal reserves.

Jan 1, 1927

By S. Kwon, J. W. Wilson

"In salt and potash mines, the time-dependent deformation mechanism should be clearly understood based on in situ measurements to predict the performance of a mining design. In this study, in situ deformation measurements from the Waste Isolation Pilot Plant (WIPP) and other salt and potash mines were used to determine the transition time from the primary to the secondary creep stage and to investigate the influence of adjacent excavations such as a nearby tunnel excavation, panel excavation and/or pillar extraction on rock deformation. IntroductionThe deformational behaviour of underground excavations in salt and potash mines is complex due to the time-dependency of the rocks. When the material properties are determined from laboratory tests, they should be carefully applied to in situ conditions, because in situ conditions are completely different from laboratory conditions. For instance, in situ deformation measurements show that the deformation rate decreases with time similar to those observed in the laboratory during the early stages. However, the rapid decrease of deformation rate does not come from the microscopic strain hardening effect observed in laboratory tests, but mainly from stress relief around the opening after its excavation (Baar, 1977). It is, therefore, recommended to undertake in situ measurements and use them to understand the deformation mechanism.Even though in situ measurements are widely accepted as important information for understanding the deformation mechanism of salt and potash (Barr, 1971; Kovari and Amstad, 1993), not many publications have focused on the fundamentals of data measurement, the application of the measured data, and the development of data analysis techniques. Recently, several new techniques for better understanding the deformation mechanism of rock salt have been developed that are based on in situ measurements. Kwon and Miller (1995) developed a new technique for describing the actual deformational behaviour of an underground excavation in rock salt. The migration of “zero strain boundary,” which represents a no movement boundary around an underground excavation, could be calculated by the technique developed by Kwon and Miller (1996). Kwon and Wilson (1997, 1998) applied neural network techniques to in situ deformation measurements to predict the deformational behaviour of the underground excavations at the Waste Isolation Pilot Plant (WIPP) located in the United States.In this study, in situ deformation measurementsfrom the WIPP site and other salt and potash mines in the United States were extensively analyzed to understand the deformation mechanism of the underground excavations in the rock mass."

Jan 1, 2002

By G. Marchand, R. H. Hay, E. C. Pearson

"AbstractA polishing .technique is described together with two anodic etching methods for aluminum and its alloys. Some of the optical and structural characteristics of the film formed by •these etching methods are discussed and it is shown to what degree these properties of the film are related to the crystallographic orientation of the metallic substrate. Applications to the study of recrystallization and twinning phenomena and to the study of plastic deformation, banding, and texture estimation are discussed. Micrographs are shown .to illustrate the manner in which the technique is particularly well suited to the study of such phenomena.IntroductionThe physical metallurgist is constantly faced with the problem of polishing and etching of metallic sections. Mechanical polishing is tedious, time consuming, and not applicable whenever a surface entirely free from plastic deformation is required. Etchants are generally required to reveal the grain structure in order to determine its size, shape, and regularity, or to bring up constituents. In the case of aluminum, the .most common etchant to reveal grains is a mixture of three acids: HC1, HN03, and HF. This etchant is fairly satisfactory on certain alloys and for certain metallurgical conditions but in general fails to give a good definition of the grain on castings, on highly alloyed products, and whenever the grain is smaller than 100 microns in diameter. Besides size and shape, a grain, or crystal, has an orientation and may be endowed with several types of imperfections."

Jan 1, 1952

By J. van Deventer

Volatile gold prices in the face of rising costs for mining and refining is causing the mines to look for new ways to reduce costs and increase recoveries. This task is complicated by the fact that the gold in hereto unexploited reserves is associated with increasingly complex ores - either preg-robbing, refractory, associated with high concentrations of copper, or all of the above. Ion exchange resins can play a significant role in this quest for improvement. Although ion exchange resins have been used in Former Soviet Union (FSU) countries for the recovery of gold for many decades, it is still not widely used in the Western World. Synthetically manufactured ion exchange resins can be tailor-made to suit the chemical and mechanical characteristics of a specific application. As such, ion exchange resins can be used in a variety of solution matrices (e.g. cyanide, thiosulphate and acid), and process designs (recovery from clear liquor after solid-liquid separation or directly from the leached pulp). In this paper, a number of applications are discussed along with a review of recent developments in ion exchange technology.

Jan 1, 2014

By M. E. Coleman, G. Money

Pneumatic Conveying and Process Injection Technologies have been implemented in the metals markets for the last 40 years and have considerably improved the productivity and the performance of many processes. There have been many steps forward in handling technology and this paper seeks to consider those now offered by Clyde Materials Handling who as an established customer-driven solutions provider has turned its attention to supporting the Metals Market. Clyde seeks to utilise its knowledge, expertise and technologies to transform the production processes of its customers, who operate in the ferrous and non-ferrous metals industries.

Jan 1, 2008

By Maureen E. Lipkewich

Education builds long term awareness, acceptance and support for responsible mineral resource development. The MABC Education Program is an award winning education partnership with British Columbia classroom teachers that has helped over 5400 teachers with resources and other learning opportunities. Each year, thousands of students begin, and continue, to learn about our modern mineral industry as a result of this teacher-written program. The CIM network has an integral role in the future of mineral education in today?s classrooms in Canada and programs of this caliber are vital to our future. The industry needs help in raising awareness of the benefits of modern mining and teachers need help in acquiring that information.

May 1, 2002

By K. S. Raja, F. Battick, B. Pesic

"CeO2 doped with lower valence cations, such as Y3+, Sm3+, Gd3+ etc. is considered as electrolyte material for low temperature SOFC. Doping introduces additional oxygen vacancies and improves ionic conductivity. This work describes the preparation of yttria-calcia doped-ceria precursor material, its sintering in DC and AC field methods, and characterization of sintered electrolytes with respect to the ionic conductivity. Doped precursor materials were prepared by a controlled co-precipitation process. Sintering of prepared, pelletized particulates was carried out using three different methods such as: 1) conventional; 2) spark plasma sintering; and 3) an alternating current field at 1125°C (AC assisted sintering). The mechanism involved in the conductivity improvement as a function of defect density, grain boundary area and phase stability will be discussed. INTRODUCTIONThe performance of SOFCs depends highly on the properties of materials. Subtle variations in the composition, microstructure, or density of SOFC components can considerably alter the power output capabilities of fuel cells. Early SOFCs utilized zirconia based electrolytes but efforts in lowering the operating temperatures of SOFCs have prompted investigations into several other oxygen ion conductors – often modified with dopants to either promote the formation of oxygen vacancies or to stabilize a vacancy rich high temperature phase – such as bismuth oxide, lanthanum gallate, and ceria.The transport of oxygen ions through the electrolyte first begins with diffusion into the material. While this is generally a surface kinetics phenomenon, it is safe to say that it is highly dependent on oxygen pressure and vacancy gradients. The role of the cathode in SOFCs is to reduce oxygen at the electrolyte surface creating an O2– ion gradient which induces permeation into the material. Once inside and under the influence of a potential field, O2– ions migrate by a vacancy hopping mechanism, Catlow, C.R.A. (1990), effectively exchanging positions throughout the matrix until they reach the anode and react, thus leaving the matrix."

Jan 1, 2012

By CH. Liu, H. X. Jiang, X. Xiao

"A study has been conducted to characterize the fatigue life in 7050-T7451 thick plate by the comparison between an experimental alloy and commercial alloy. The fracture origins were specified and their sizes were measured by scanning electron microscope (SEM). Additionally, the size, number density and spatial distribution of porosity in the experimental material and commercial material were characterized and compared, using X-ray Computed Tomography(XCT). The results showed that microporosity was the predominant site for crack nucleation and subsequent failure of the experimental alloy. However, as for the commercial alloy, fatigue cracks were found to originate from constituent particles. The presence of microporosity in 7050-T7451 thick plate reduced fatigue life of an order of magnitude or more compared to the commercial alloy. The relationships between size of origin and fatigue life were proposed. It was showed that the fatigue endurance was reduced when the size of porosity increased.INTRODUCTION 7xxx series aluminum alloys, due to their combination of high strength, high resistance to stress corrosion cracking, and good fracture toughness, are widely used in structural engineering applications where high-strength and low-density characteristics are fundamental design requirements (Williams& Starke, 2003). Every designer is striving to find an optimal combination of properties including strength, corrosion resistance and fatigue resistance (Wanget al., 2016). Based on the design principles of aircraft, a higher fatigue resistance of aluminum alloys are required. Thus, many investigations have been carried out on the microstructures and its effect on fatigue properties of the 7xxx series aluminum alloy (Robson, 2004; Schubbe, 2009).Microporosity, which is a common defect in casting materials, can lead to a significant deterioration of mechanical performance and fatigue resistance, especially in the high alloyed 7xxx aluminum alloys. The actual valid loading area decreases due to microporosity, which results in detrimental effect on the mechanical properties. Many experimental studies have been conducted in this research field. Mayer et al.(2003) investigated the fatigue properties of magnesium alloys produced by high-pressure die-casting. The results show that porosity in magnesium alloys greater than0.18mm diameter may be considered as the most important material defect for high cycle fatigue and fully reversed loading conditions. Nadot et al.(2004) found that the near surface defects are much more dangerous than the internal defects. Wang et al.(2001a) used the Weibull statistics method to analysis the influence of the microporosity, oxides and particles on the A356-T6 alloy fatigue life. The results show that, the porosity is more detrimental to fatigue life than oxide films and particles. With regard to fatigue resistance, although the deleterious effect of microporosity has been generally acknowledged, a quantitative understanding between casting microporosity and fatigue life in 7050-T7451 plate is not well established."

Jan 1, 2018

By P. Mottahed, E. De Souza

One of the major unsolved problems of safe, economical roof support in the evaporite industry has been that of obtaining and maintaining anchorages in relatively soft rock. This is due to the viscoelastic and viscoplastic behaviour of salt rock and associated deposits. This paper introduces a low-cost, yieldable support mechanism, consisting of a system of buckling disks, which provides viable solutions to dynamic support. The yieldable support system offers a number of advantages in comparison with existing dynamic support systems. It is characterized by its simplicity in design and installation, repeatability in behaviour and cost effectiveness. It also has the added advantage of providing the operator with a means of assessing support behaviour and ground performance by direct visual observation of changes in disk shape. Thus, the system can be utilized as a warning mechanism of ground stress and support load conditions. Such system not only provides a feasible and more effective rock mass stabilization strategy but improves mine safety.

Jan 1, 1999

By E. Swartzman

This paper presents a general re-view of the various methods of briquetting coals, with and without the aid of a binder, with special reference to the production of a suitable briquette from Nova Scotia 'fines' for re-blending with industrial coal. From the economic and technical viewpoints, either small stoker-sized briquettes made with about 4 per cent asphalt in standard low-pressure double-roll presses, or briquettes made without binder in high-pressure double-roll presses, appear to be the most reasonable solution at present.

Jan 1, 1959

By Charlie Graham, Helen Shang, Ashley Scott, Andrew Hall

"Approaches to Energy Recovery• Upgrading for electricity generation - steam turbines• Direct extraction- process improvement or space heating- support medium for animal or plant growth– fish or microalgae• Heat pumps- space heating/coolingWater Energy Grades• High (150+ °C) - electricity Generation• Medium (26 to 121 °C) - direct extraction• Low (5 to 18 °Celsius)- use of heat pump is required• Temperatures between zones will depend on circumstances for best use."

Jan 1, 2012

By T. Skinner, M. Sahebkar

"In recent years, the mining industry has been inundated with new technologies and software systems to aid in productivity improvement. Accompanying this increased level of technology and computer systems has been the exponential growth in data sources and sinks for all aspects of a mining operation. This rapid growth in data and technology has evolved through vendor “push” approaches and user “pull” scenarios, the result of which has been that currently, no standards exist defining how data from new technology should be accessed and transferred from surface mining equipment and systems. Consequently, many incremental benefits of the systems have not been realized. This paper will present a discussion of this important issue and introduce a new committee formed to address standards to assist the industry in making effective use of current and future technology. Potential benefits accruing from the development of these standards will be illustrated through the use of a case study at Fording Coal Limited. IntroductionThe mining industry is currently faced with a rapid evolution in the computing-based systems capabilities of mobile production equipment. At the same time, there is a trend toward the introduction of even larger machines, with novel designs or incorporation of new technologies within existing designs. Computing and control technology will be required to operate and acquire knowledge about equipment operation, utilization, and performance. Such knowledge has the potential to lead to enhanced equipment design, more appropriate equipment selection, and optimized equipment performance. The equipment systems will be required to be integrated with mine production monitoring systems, maintenance management software, and a wealth of other information systems to provide a complete understanding of the effects of various factors such as maintenance, equipment design and production on economics (Roman and Daneshmend, 2001). This will lead to a better understanding and implementation of the opportunities to enhance the performance of the mine through interaction of the mine operations."

Jan 1, 2003

By Th. Hassel

The application of magnesium as an absorbable biomaterial demanded the consideration of the alloy composition, the mechanical properties and the corrosion a special adapted material development in terms of the human biological system. Magnesium for technical applications mostly comprised alloying elements up to 10 wt%. Thereby often metals (e.g. rare earth and aluminum) with high toxic potentials are used to optimize the mechanical properties. To minimize toxic reactions during the degradation of a absorbable magnesium alloy, the Mg-Ca system is being selected and investigated because both elements belong to the mineral nutrients. Rods and small tubes are produced by extrusion of gravity die casting billets (Ca-content 0.4 to 4.0wt%). The positive grain fining influence of calcium and its improvement of the corrosion behavior are additional advantages. The microstructure, the mechanical properties and the corrosion attitude are investigated. The results show that an optimal composition of micro alloyed Mg-Ca and ideally processing parameters lead to 16% strain and a tensile strength up to 185MPa. Electrochemical investigations and measurements of the hydrogen production demonstrate the influence of the Ca-content to the corrosion behavior of the investigated alloys.

Jan 1, 2006

By M. Leahy

"Very little is known about the large scale fluid dynamics and associated distribution of copper in an operating electrowinning cell, yet they will have a major influence on mass transfer and plating quality. The CFD model in this work is used to simulate an entire EW cell with 60 cathodes and 61 anodes, or 121 anode–cathode pairs, elucidating for the first time the three-dimensional (3D) flow and copper distribution in an industrial cell. Two methods for the distribution of electrolyte are modelled:1. Downcomer method: electrolyte is fed by a downcomer at one end of the cell, overflowing at the opposite end.2. Manifold method: a horizontal manifold pipe runs the whole length of the cell and feeds electrolyte via small holes in the top of the manifold pipe.The recirculation that develops within each anode-cathode pair, driven by oxygen bubble generation on the anode, is similar to that seen previously in two-dimensional models of single anode–cathode gaps. However a more complex 3D flow recirculation is established, which involves flow of electrolyte down the side gaps (being a path of low resistance for return flow) as well as the usual return flow down the cathode side of each pair gap. The bubble-driven flow is not influenced by the mode of electrolyte distribution.The electrolyte flow due to the manifold and downcomer is somewhat secondary to the bubble driven flow. In the case of the downcomer distribution mode, the high injection velocity causes a very turbulent flow in the first 1–2 m down the cell from the downcomer, with several large vortices developing. This may lead to some sludge particles being entrained into the bulk of the cell.In the manifold pipe case, the jet from each hole is dissipated very quickly, within the first 10–20 cm. The jets are directed into the downward flowing zone of the bubble-driven recirculation, which leads to unstable and periodic behaviour on a large spatial scale.In both the manifold and downcomer cases, there is a marked two-zone vertical stratification in copper concentration."

Jan 1, 2016

By F. J. Tozer

Canal communication between Lake Erie and Lake Ontario has been one of almost constant enlargement and reconstruction to meet the rapid growth of trade and commerce, and the consequent steady increase in the size of vessels plying the Great Lakes. The original canal was built by the Welland Canal Company. The first sod was turned in 1824 and the first vessel passed through in. 1829. There were 36 lift-locks, built of oak timber, 110 feet long and 22 feet wide, with a depth of water over the sills of 8 feet. The second canal, now known as the 'Old Welland Canal' was built by the Dominion of Canada (1842 to 1850). There were 26 masonry locks, 150 feet long, 26.5 feet wide and with a depth of water over the sills of 9 feet. The walls and banks were raised in 1853 to give a 10-foot draught. The third canal, known as the 'New Welland Canal, built by the Dominion of Canada, was started in June 1874 and the first boat passed through in the spring of 1882. There are 25 masonry lift-locks, 270 feet long, 45 feet wide and with a depth of water over the sills of 12 feet. The walls and banks were raised in 1891 to give a 14-foot draught. This is the canal in use at present.

Jan 1, 1926

By L. Bloomquist

This paper describes how Automated Mining Systems (AMS) is evolving the state-of-the-art in guidance systems for autonomous underground vehicles. The techniques, trade-offs, and lessons learned from these systems are described, including the safety regime that has been implemented. First generation autonomous guidance systems for underground vehicles relied on infrastructure for the vehicle to follow. However, there are additional costs associated with that approach. The current generation uses a pair of laser range finders as its only guidance sensors. This system uses a minimum of infrastructure, in the form of a redundant system of location referencing. Advanced steering and drive control algorithms are incorporated into this generation of system. The next generation of infrastructureless guidance systems will be based on a 3D vision sensor, which was originally developed for autonomous Mars rovers and is being adapted for underground mining use. Results of early underground field trials are presented, along with a description of this emerging technology.

Jan 1, 2004

By L. Bloomquist, C. Arnoldi

"This paper describes how Automated Mining Systems (AMS) is evolving the state-of the- art in guidance systems for autonomous underground vehicles. The techniques, tradeoffs, and lessons learned from these systems are described, including the safety regime that has been implemented.First generation autonomous guidance systems for underground vehicles relied on infrastructure for the vehicle to follow. However, there are additional costs associated with that approach.The current generation uses a pair of laser range finders as its only guidance sensors. This system uses a minimum of infrastructure, in the form of a redundant system of location referencing. Advanced steering and drive control algorithms are incorporated into this generation of system.The next generation of infrastructureless guidance systems will be based on a 3D vision sensor, which was originally developed for autonomous Mars rovers and is being adapted for underground mining use. Results of early underground field trials are presented, along with a description of this emerging technology."

Jan 1, 2004

By J. A. Meech, R. J. Tucker

"Since the establishment of froth flotation as an effective method of mineral beneficiation there has been both academic and industrial interest in the levels of the various reagents required to perform the desired separations. Academic interest was spurred by a desire to understand the mechanisms involved - industrial interest by a need to improve the efficiency of the process. These efficiency improvements can take two forms: cost reductions due to reduced reagent consumption and/or improved separation efficiencies. The latter are indicated by either improved grade-recovery relationships for removal of a valuable mineral from gangue, or improved separation of two similar valuable minerals.The processing of lower grade ore bodies at higher tonnage rates has necessitated increased interest in both reagent consumption and metal recovery. Furthermore, the development of accurate and functional on-stream analysis equipment in the 1960's and 1970's has allowed for a better understanding of the dynamic processes involved in a flotation circuit and has required a more concrete statement of the relationships and reactions between the minerals and chemicals in the flotation pulp. Development of these relationships is necessary in order to make use of on-stream analysis to control the process at, or near its more efficient level."

Jan 1, 1984

By Michael L. Wayman

Archaeological and ethnographic work during the last century has shown clearly that metals have played a small but important role in prehistoric Arctic cultures. For at least the past several millenia both iron and copper have been used in the North, primarily for blades, projectile points, knives, awls, engraving tools, fishhooks, scrapers and axes. In addition they were used for joining purposes as staples and rivets. It is of great interest to enquire into the origins of these metals. In this connection one begins with the observation that to date there has been no clear evidence for the smelting or melting of metals in the Arctic prior to the arrival of Europeans. This can be explained partly by the absence of traditional pyrotechnologies such as the high-temperature firing of ceramics and the heat treatment of bone and wood. Another factor which surely inhibited the development of smelting/ melting operations is the relative absence of wood in the region. The production of charcoal for smelting requires large quantities of wood, to the extent that the desertification of a number of areas in the Old World is believed by some to have been at least partly caused by charcoal production. In the North this was obviously not possible. Thus the Arctic peoples were restricted to using native (naturally occurring) metals and metals obtained by various direct and indirect forms of contact with areas of the world where smelting was practiced. Both of these sources were important in the case of iron; we know that meteoritic iron, telluric (native) iron and smelted wrought iron were all used in the Arctic. These three types of iron will be considered in tum.

Jan 1, 1999