Search Documents

By H. Dykstra

Calculated wellbore pressures were obtained for parameters of radilcs ratio and permeability. In all cases bur two, after-production was allowed to occur for one day. The calculated pressure build-up data were compared with actual pressure build-up data from a condensate well. The paper discusses the comparison, gives reasons for, inability to match calculated (2nd actual data, and presents conc1usions derived from the comparison. INTRODUCTION Considerable information has been published on the decline in wellbore pressure for oil and gas fields resulting from production of fluids. Considerable information also has been published on pressure build-up for oil fields, but relatively little has been published for gas and condensate fields. Perrine' summarized the equations derived for pressure build-up in oil wells and showed how the different methods could be applied. On the other hand, very little theoretical information has been published on pressure build-up in gas or gas-condensate wells.2-4 Tracy,' by pointing out the similarity between the equation describing oil wellbore pressure decline and the equation describing gas wellbore pressure decline, showed how methods of pressure build-up analysis could be applied to a gas well. In analyzing pressure build-up data for gas or gas-condensate wells, it would be very desirable to compare actual pressure build-up data with calculated pressure build-up data. Such a comparison would lead to a better feeling for the quantitative picture of gas-well build-up curves and would help to establish a degree of confidence in a given build-up curve. This paper discusses the comparison and presents conclusions made from it. Calculated wellbore pressures are given for parameters of radius ratio and permeability. In all cases but two, after-production was allowed to occur for one day. The work was done in an attempt to evaluate the reserves of a gas-condensate field. As will be discussed later, it was not possible to make an evaluation. METHOD OF CALCULATION The method used for solving the depletion and pressure build-up behavior for a gas-condensate well was that developed by West, Garvin and Sheldon.5 or the IBM 704 computer program used, it was assumed that liquid condensing out of solution would have only a minor effect on the flow behavior. Therefore, the field was treated as having single-phase flow, with the gas saturation S, remaining constant at unity minus the connate-water saturation Sw. As will be discussed later, this may not have been a good assumption. It also was assumed that oil production could be considered as equivalent gas production by using a conversion factor based on an analysis of the liquid produced. An outer boundary condition of no-flow was assumed. BASIC DATA The data required for the study were reservoir properties, fluid properties and production data. Reservoir properties included the following: thickness h, 179 ft; porosity, 0.194; connate-water saturation, 0.43; gas saturation, 0.57; permeabilities k, 1.0, 0.5, 0.25 and 0.15 md; radius ratios re/rw, 800, 1,000 and 2,000; wellbore radius rw, 5 in.; initial reservoir pressure P, 6,529 psia; and reservoir temperature, 272°F. The selection of permeabilities was based on core-analysis data showing an average air permeability of about 2 md. With a relatively high connate-water saturation, the average effective gas permeability would be about one-half, or less, of the air permeability. The selection of radius ratios was based partly on the observed rapid decline in wellbore pressure during production and partly on the fact that the well was believed to be located in a relatively small fault block. Reservoir fluid properties were obtained from a reservoir fluid study on a recombined sample of gas and condensate. Gas formation-volume factors were calculated from pressure-volume measurements made at reservoir temperature. Gas viscosities were calculated by the method of Carr, et al,G from an analysis of the re-combined sample. These data are shown as a function of pressure in Table 1. The production schedule from the gas-condensate

By G. A. Vissac

MoIstuRe in coal must be considered as an impurity, just the same as ash, from the standpoint of utilization of the coal. Being incombustible, it reduces directly the heating value of the coal, and in addition absorbs heat for its evaporation. Its presence means useless expenditures in handling and transportation. In coke plants, extra moisture reduces capacity and may cause damage to brick work and equipment. Accordingly, the removal of extra moisture can be considered just as important as the removal of other impurities, such as ashes, in the modern coal preparation plant. Moisture, which can be removed by heating the coal up to a temperature of 100°C, may be retained in various forms: 1. As a film, on the surface of each coal particle, and in the interstices between particles, retained by capillary forces. 2. Or "occluded" inside the coal particles. This occluded moisture may be either free moisture (as in a sponge), or hygroscopic moisture which varies with atmospheric conditions, (also called "regain"). These latter forms of moisture are particularly common in "young" coals (subbituminous and lignites); bloom coals (seam outcrops); fusain; and carbonized products. In our study of coal drying, we shall consider only the removal of free moisture, exclusive from hygroscopic moisture. Dewatering If we reserve the name of drying to the removal of water by evaporation, we must consider the initial phase of the mechanical removal of free moisture as a distinct operation covered by the term dewatering. In all cases the free water carried over the surface of the coal particles or in their interstices, or in their pores, is retained by capillary forces. Dewater-ing is accomplished by breaking or counteracting these capillary forces; removal of as much water as possible by dewatering methods is usually advisable, as the cost of these operations is generally much less than by evaporation. The most common methods of me-chanical dewatering are: 1. "Pressure piling," which reduces the interstitial spaces, accomplished in dewatering bins or over dewatering screens. 2. Or dynamic methods, such as used in centrifuges or over vibrating screens. We shall only mention the " preferential wetting" method, in which surface water can be displaced by hydrocarbons, as offering possibilities, but which, to our knowledge, has not reached yet a practical development. But we must point out that the capillary forces retaining water on the coal surfaces, decrease considerably with increased temperatures. This is the principle used in all modern dishwashing machines; by using very hot water, dishes are extracted almost dry. In line with this development, we favor the type of dryers including a dewatering section; as the coal enters the dryer and is gradually brought up to higher temperatures, its dewatering ability is increased and advantage can be taken of this conditioning, resulting in increased drying efficiencies and reductions in drying costs. Heat Drying In the final phase, the remaining moisture must be evaporated. Coal and water must be brought up to the chosen temperature of evaporation, and heat must be supplied to fill the requirements of the latent heat of evaporation of the water to be removed. Accordingly, drying becomes largely a problem of heat transfer, and drying methods can be classified accordingly, namely: 1. Radiant transfer. 2. Transfer by surface contact and conduction. 3. Transfer by hot gas contact. The first method is not applicable to coal drying; the second method is used in the old type rotary dryer. The third method, the most commonly used in modern coal dryers, will be the only one considered here; and, of course, we shall deal with continuous types of dryers only. The mechanism of complete drying is really very complex-—several phases are involved: 1. The constant rate period. 2. The uniform falling rate period. 3. The varying falling rate period. As most of our practical coal drying problems deal with wet coals (over 6 pct of moisture), and do not require complete drying (under 1.5 pct), we shall deal with the first condition only, namely the constant rate drying. Dryer Calculations Instead of presenting the algebraic formulas, we believe a concrete example will provide a clearer illustration. Assume a feed of wet coal at the rate

Jan 1, 1950

By Strathmore R. B. Cooke

On the basis of experiments conducted on quartz using a bubble pick-up method, it was shown in an earlier paper1 that this mineral will preferentially adsorb hydrogen, calcium, or sodium ions, depending on the relative concentrations of those ions in the solution in which the quartz is immersed. For quartz particles ranging in size from 0.2 to 1 mm, it was demonstrated that the concentration of calcium in solution (assumed present as ions) necessary to completely activate quartz for flotation is given by the expression: Ca++ = [H+] X 106 + [Na+] X 10-3 In this expression, ionic concentrations are in mols per liter. It was further shown that the pick-up method is apparently more sensitive to changes in reagent concentration than the standard captive-bubble method, and that induction times are apparently much reduced. Since completing these earlier tests, a new type of cell has been constructed; this is shown in Fig 1 and 2. In Fig 1, A is a ground joint, B is a central tube reaching to within a few millimeters of the bottom of the cell, and C is a stopper which may be removed for reagent addition, and serves the further purpose of excluding carbon dioxide from the air during the test. The entire cell is constructed of Pyrex glass, and does not give the trouble experienced with the earlier cell, in which activating ions were released from the glass at high pH values. The only critical factor in the construction of the cell is the clearance between the central tube and the bottom of the cell. This clearance should be sufficiently small that the bubble can be pressed directly on the mineral grains lying on the bottom of the cell. In the pick-up tests to be described in this paper, the reagents used were all of C. P. grade, except the sodium oleate, which was Merck's "neutral powder." The quartz employed was water-clear vein quartz, sized on screens, cleaned with both hydrochloric acid and sodium hydroxide, and given a thorough final washing with distilled water. Experimental procedures were the same as described in the earlier paper. EFFECT OF SIZE OF QUARTZ ON PICK-UP To ascertain the effect of particle size on the adsorption of calcium ions, the quartz was sized from minus 14 plus 20 mesh through the intervening screen sizes to minus 270 mesh plus 400 mesh. Each size was thoroughly cleaned, and then tested in the cell at different calcium chloride and sodium hydroxide concentrations, and at a constant sodium oleate concentration of 20 mg per liter. All particles, within the size range given, exhibited complete pick-up within the curve expressed by the equation above. This presumably means, when the conditions imposed by the equation are satisfied, that this maximum is independent of particle size. However, it was found that the range through which partial particle pick-up occurred progressively broadened as particle size decreased. This is shown in Fig 3, in which curves B, C, and D show the limits at which pick-up just commences (as the pH is increased) for particles of minus 14 plus 28 mesh, minus 65 plus 100 mesh, and minus 270 plus 400 mesh size, respectively. These results indicate that for satisfactory activation, at any given pH, a lower calcium ion concentration is required for fine particles than for coarse particles. EFFECT OF HIGH ALKALINITY ON PICK-UP At calcium concentrations of between 1 and 10 mg per liter, and at high alka-linities, it was noticed that pick-up ceased as soon as calcium hydroxide commenced to precipitate. This effect was investigated at other calcium concentrations, with the same results. Solutions of calcium chloride, containing 105, 104, l03, and l02 mg of calcium per liter were made alkaline with sodium hydroxide until calcium hydroxide just started to precipitate, according to the following equation: CaCl² + NaOH -+ Ca(OH)2 + 2NaCl The beginning of precipitation was taken as that point at which either a faint opalescence appeared in the solution, or a Tyndall cone became ap-

Jan 1, 1950

By Walter A. Backofen, Donald H. Avery

Intense primary and cross-slip traces were observed in easy glide on Cu: 6 pct-A1 single crystals deformed in tension. A mechanism of cooperative source operation is developed which recognizes that both the applied stress and that resolved from dislocation arrays contribute to the stress on a source. By considering the stress from arrays, the activation of secondary systems in easy glide and the difference in appearance of slip markings on pure and solid-solution crystals are explained. Furthermore the cross-slip system is predicted to be second favored during easy glide for a large range of orientations. FROM many studies of easy glide in fcc metal crystals, a pattern of observations has developed which still requires full explanation. In pure copper, aluminum, and silver, the easy-glide, slip traces are fine and uniform with steps 50 to 100A on the primary* system.1-4 Yet it has not been at all clear why slip in the pure materials should occur in this way. On the contrary, one might expect, with simple slip and a low hardening rate, that the weakest sources on the primary system would operate extensively to produce strong slip traces. In a brass, however, intense slip steps up to 0.5 are found on both primary and cross-slip system4,6-9 seeger10 has pointed out that in a material of low stacking-fault energy such as a brass, extensive easy-glide cross-slip could not be thermally activated, but rather must originate on the cross-slip plane. In further explanation, the wilsdorfs4 and seeger10 noted that only the cross-slip system would not harden differently than the primary, whatever the latent hardening tendencies of other systems; therefore, in brass, which exhibits high latent hardening, the cross-slip is the only secondary system which could be expected to operate extensively, once it became active. The explanation of how the cross-slip system, on which the applied stress is low, becomes activated has been related, in a nonspecific way, to pileups by Hirsch11 and Honeycombe.l2 In the work to be described, deformation traces on solid-solution Cu: 6 pct A1 single crvstals were studied with conventional light microscopy and a mechanism proposed to explain both the observed activation of secondary systems in easy glide and the difference in appearance of slip markings on pure and solid-solution crystals. EXPERIMENTAL In preparing the Cu-A1 single crystals, rectangular bars approximately 0.4 in. by 0.4 in. by 6 in. were first machined from ingots made by vacuum melting copper of 99.999 pct and aluminum of 99.99 pct purity. They were then packed in powdered graphite and the crystals grown in a modified Bridgman apparatus at a rate of 5 mm per hr under an atmosphere of purified nitrogen. Crystal perfection as indicated by Laue back-reflection spots was good except for the last inch to freeze, which was discarded. Orientations so determined are shown in Fig. 1. Tensile specimens with a reduced gage section were obtained by masking the ends with electrical tape and chemically polishing in a solution of 20 pct HNO3, 24 pct HAc, 52 pct H3PO4, 2 pct Hcl, and 2 pct H20 at room temperature.13 Finally, the specimens were electropolished in a 30 pct ortho-phosphoric acid bath at 12 v. Tensile deformation was performed in an Instron testing machine at a strain rate of approximately 1 pct per min. During easy glide, extensive cross-slip was observed with all crystals, in spite of the low Schmid factor on this system, and in no case was any other secondary trace encountered. A certain sequence of slip-line development was associated with the extension. At yielding, intense primary traces passing completely through the crystal developed at some point on the gage section, generally near the grips; weak cross-slip traces also appeared, extending from the primary traces into the adjacent undeformed crystal, Fig. 2. Further extension led to primary traces adjacent to the first-formed and connecting with those of the cross-

Jan 1, 1963

By W. F. Mullen, C. W. Stickler

WITH few exceptions, unit operations in the Pennsylvania slate industry in 1950 did not differ appreciably from production methods described by Behrel and Bowles2-4 several decades ago. Many traditionally picturesque but relatively inefficient hand operations continued to contribute to high operating costs in an industry in which the margin of profit, for various reasons, was admittedly low. As part of a general program in which the Pennsylvania State College has been assisting the slate industry to solve some of its problems, time and method studies were used in an effort to determine the bottlenecks of production flow. The results are as applicable to other stone industries as they are to slate. A study of the basic elements in the production of roofing slate, structural slate, and slate blackboards among selected slate producers revealed comparatively few refinements. Any marked difference in operating method was characterized largely by the available equipment, a noticeable difference in the working properties of the rock quarried by a particular company, and by either the habit thinking or ingenuity of the individual operators. With the hope that significant economies in manufacture might result, all the unit operations were broken down into elements for study and analysis. The greater part of the study encompassed those operations from the quarry rim to the finished product; however, to obtain a reasonable synthesis of time allotments per operation, several analyses of quarrying from the finish of the wire saw cut are included for reference. The complete study of quarrying made by Bowles several years ago resulted in the introduction of the wire saw into the operation; there appears to be a need for as fundamental a change in the processing of finished slate as the wire saw was in the quarrying process. Fig. 1 illustrates the flowsheet of quarried rock from the parent bed to the quarry rim with the basic elements which contribute to the difficulty of removing slate from the ground. In Pennsylvania roofing slate is produced by one of three procedures, many operations of which are quite similar. In the traditional or classical method the quarried rock is reduced by sculping and auxiliary manual treatment to workable size and then is split and dressed (trimmed to size) in the conventional shanty. Archaic as this method might appear, there are several elements that result in substantial savings over more mechanized operations. In a modified version of this method, the block is reduced by sawing and gouging preparatory to splitting and dressing in indoor stations. This method is particularly adaptable to rock which fractures unevenly by conventional sculping methods. In the third and more modern method, reduced block received from the block maker is diamond-sawed to length and finished on a production line. Fig. 2 illustrates the flow pattern in each case. In the modified and more modern plans, dressing is done on mechanically-operated trimming machines, which appreciably reduce the fatigue factor of the operator. However, it should be noted that it is advantageous for the operator to be able to control the speed of the knife to prevent breakage of certain classes of stock. In the classical plan the splitter and dresser normally act as blockmakers also and carry their eighter slabs (equivalent in thickness to eight shingles) into the shanties themselves, all of which adds to fatigue and reduced efficiency. The extremely low investment and operating expense of the classical method has undoubtedly been of paramount importance in its continuation. Production of Mill Stock The production of mill stock is accomplished by less picturesque methods than enter into the production of roofing slate but it is, in the main, relatively more efficient because of the increased use of machinery for handling and for finishing. Mill stock can be classified into two categories as far as difference in production method is concerned: structural slate and blackboards. The significant difference in operation is caused largely by the nature of the rock used for each product with the best and easiest cleaved rock being reserved for blackboards to permit the splitting of large slabs to as little as 1/2 in. in thickness. Structural stock, on the other hand, is split into panels no thinner than 11/2 in. and

Jan 1, 1952

By R. P. Aikman, F. G. Miller, J. M. Podgursky

As part of a larger study of the mechanism of froth flotation of coal, the rates at which coal particles of various size and specific gravity react to froth flotation were investigated. Results of this study show that in flotation: I) recovery rate increases, but selectivity decreases with a decrease in particle size down to 100 mesh, and 2) recovery rate is constant for all sizes between 100M and 325M. n response to the growing demand for low-sulfur coking coal for iron making, the coal industry is continually striving to perfect methods for cleaning coal to acceptable ash and sulfur levels while maintaining maximum product yield. By present standards the industry has adequate processes for cleaning coarse coal, i.e., + 28 mesh, at almost any desired specific gravity. However, in the case of fine coal, i.e., —28 mesh, neither of the two existing processes - froth flotation or hydrocycloning — in its present state of development yields products that are comparable in ash and/or sulfur content to products normally obtained from coarse coal processes. The work outlined in this paper is part of a larger study directed toward maximum exploitation of froth flotation for fine coal processing. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of froth flotation with other fine-coal processing methods. The paper includes: 1) A discussion of the value of a detailed wash-ability study as a method of assessing the problems associated with fine coal processing, 2) A general discussion of hydrocyclone principles, included to serve as a basis for understanding the mechanism of coal flotation, and 3) A detailed discussion of the mechanism of coal flotation, as well as the research leading to the optimum use of froth flotation in combination with other fine-coal cleaning methods to provide efficient fine-coal processing. Our study of the rates at which coal particles of various size and specific gravity react to flotation shows that in flotation: 1) recovery rate increases but selectivity decreases with a decrease in particle size down to 100 mesh, 2) recovery rate is constant for all sizes between 100 mesh and 325 mesh, and 3) the flotation process effectively rejects only those extremely fine particles which do not contain surface carbon. (Because of this feature, froth flotation is an excellent method for rejecting clays - the only extreme fines in - 325-mesh coal that are always carbon free.) Washability studies of flotation products are used to assess flotation efficiency. These studies show that: 1) the increase in percent sulfur in flotation products above the theoretical sulfur content as defined by the washability study is due almost entirely to flotation of fine high-specific-gravity particles that are part coal and part pyrite, and 2) in a given size range particle floatability decreases with an increase in particle specific gravity. Error curves are explained and are used to compare the mechanisms of coal flotation and hydrocycloning. These comparisons show that hydrocyclone performance is affected primarily by particle mass, i.e., particle specific gravity and size, whereas coal flotation performance is dependent on both the particle mass and the coal surface available for bubble attachment. Since the error curve is a basic tool for rating the efficiency of any coal processing system, it will be useful to quickly review the principles of error curve construction. RATING COAL-PROCESSING EFFICIENCY BY THE ERROR CURVE The organic component of coal is of lower specific gravity than its impurities, and the most effective principle for coal concentration is therefore separation on the basis of specific gravity. However, since there is no sharp dividing line between pure coal and pure ash components, specific gravity must be closely controlled if the product is to have acceptable quality at maximum yields. In turn, the basis for close control in any coal processing system is the reference standard provided by precise laboratory washability studies. In these studies, coal is carefully separated into a series of progressively higher specific gravity fractions to establish a relationship

Jan 1, 1968

By P. G. Carpenter, R. G. Nisle, F. W. Bubb

It is the purpose of this paper to describe an electrical computer which has been constructed to solve the equations for vapor-liquid equilibrium in multi-component systems. The instrument consists of seven component-computing units each with proper indicating means and power supplies. Each unit is a resistance network with a voltage matching servomechanism, and each provides an output voltage proportional to the mol-fractions for vapor and liquid phases. These voltages are summed and matched with a reference voltage to provide the solutions. Any reasonable number of such units may be put together to make a computer. The theory and operation of the computer is discussed. A number of applications and examples of computer results are given. The computer yields the over-all vapor or liquid fraction to a probable error of 0.002. An interpolation method is described which reduces the probable error to 0.0002. INTRODUCTION The process known as Flash Vaporization may be described as follows: A mixture of known composition of relatively volatile components is allowed to come to thermodynamic equilibrium at some given temperature and pressure by any path whatsoever. In general, a vapor and a liquid phase will be present at equilbrium. The problem is to determine the fractions of the mixture in the vapor and liquid phases, and to determine the mol fractions of the various components in each phase. The relations that exist between these various quantities at equilibrium are well known and will be given later. These equations are difficult to solve, yielding only to trial-and-error methods. The virtues of the analog computer are its speed and the automatic character of its calculations. The device is operated by turning a crank which varies the value of v, the total vapor fraction. This actuates a number of servomechanisms which perform automatically all computations. This computer facilitates the solution of such problems as (to mention a few] : Analysis of separator operation, studies of changes in composition of reservoir fluids with pressure decline, and analysis of natural gasoline plant operation. Examples of some of these problems are given in detail later. STATEMENT OF THE PROBLEM The essential equations are xm = 1+(km-l)v . . (1) Kmzm ym =------------------------. . (2) 1 + (Km-l)v ; n n S S xm= --------------------=1 1 + (Km-l)v m = 1 m=1 ......(3) n n S = S Km Zm =1 S ym 1 + (Km-1)v m=1 m = l ......(4) where ym = Vm/V = Mol fraction of m-th component in vapor phase. xm = Lm/L = Mol fraction of m-th component in liquid phase. Zm = Fm/F = Mol fraction of m-th component in mixture. KM = ym/xm = Equilibrium constant for m-th component at the given temperature and pressure. v = V/F = Mol fraction of vapor in the mixture. F = Total mols of a mixture of n components. V - Total mols of vapor in the mixture. L = Total mols of liquid in the mixture. Fm = Total mols of m-th component. Lm = Mols of m-th component in liquid phase. Vm = Mols of m-th component in vapor phase. Assuming the total mols of the mixture F and its composition (all the Fm) to be known — either from a quantitative analysis or from the amounts put together to make the mixture — the zm = Fm/F may be regarded as known quantities. From the given temperature and pressure of the mixture the K., are known (principally from experimental data). The primary problem is then: having given all the zm and Km to calculate v and all the fractions xm and ym. Having calculated these ratios, it is a simple matter to calculate V. L. Vm, Lm from their defining equations. SOLUTION OF THE PROBLEM Basic Computer Unit The computer consists of n units, each of which provides voltages xEo and YE, proportional to x and y as in

Jan 1, 1950

By David E. Jones, Dean K. Hunt, C. Y. Chen

INTRODUCTION Of all the numerous geological hazards that threaten the well-being of urban areas in the United States, probably none is so widespread, persistent, and diversified as surface subsidence (HRB-Singer, Inc., 1977). Simply defined, subsidence is the vertical displacement or sinking of the ground surface caused by either natural phenomena or man's activities. The downward movement, however, can be accompanied by horizontal movement, strain, tilt and even by a locally upward movement. Damage to structures and the environment can result from any of these movements. Extracting subsurface materials, fluids and solids, accounts for most man-induced subsidence in the United States. Among all the mining-related subsidences, the collapse of voids created by underground coal mining has been the major cause in inflicting surface damage (Comptroller General of the United States, 1979). Subsidence from coal mining may occur within a few weeks or be delayed for years, depending upon the mineral layer's depth below the surface, the overlying rock strata's characteristics, the extent and methods of mining that were employed, and the time deterioration of pillar and mine structure. Unless underground resources are not mined or control measures are implemented to prevent or minimize damage, some degree of surface subsidence and its accompanied deleterious effects are often inevitable. The ways to control the subsidence and minimize surface damage may include: 1. Precautionary measures built into new structures or surface features. 2. Preventive works applied to existing structures or surface features. 3. Mine design incorporating special underground layouts. 4. Any combination of the above measures. Upon the enactment of Public Law 95-87, the Secretary of the Interior, through the recently created Office of Surface Mining (OSM), was authorized to promulgate rules to regulate mining reclamation including subsidence control. Proposed on September 18, 1978, these rules were finalized, following public comment and hearings, on March 13, 1979, as part of the permanent regulatory program for the regulation of surface mining and reclamation operations which include the surface effects of underground mining. On January 28, 1981, Secretary Watt of the Department of the Interior issued an order to re- quire all agencies to identify with recommendations all regulations which are believed to be excessive, burdensome or counterproductive. Also on February 17, 1981. President Reagan issued Executive Order No. 12291 requiring all Federal agencies to conduct a regulatory review to make a determination that each promulgation of a regulation is clearly within the authority delegated by law and consistent with Congressional intent (Federal Register, 1981). As a result, OSM initiated the regulatory reform to revise the permanent regulatory program. Following a brief discussion of the technical aspects and the effects of subsidence on man and his environment, this paper presents a historical overview of how rules and regulations are used to govern the subsidence related problems. The development of the regulation of subsidence under Public Law 95-87, the Surface Mining Control and Reclamation Act of 1977 (SMCRA or the Act) are also discussed, including the new regulations being developed under the regulatory reform program. SOME TECHNICAL ASPECTS Am EFFECTS OF FINE SUBSIDENCE An extensive historical review of mining subsidence is given by Zwartendyk (1971) and Shadbolt (1978). Comprehensive technical presentations have been given by Henry (1956), King and Whetton (1957), Hall and Orchard (1963). Muller, et al. (1968). Grard (1969), Voight and Pariseau (1970). Kapp and Williams (1972), Cummins and Given (1973), Brauner (1973) , and NCB (1975). A theory of surface subsidence due to underground mining was perhaps first fundamentally stated by a French engineer, Toillez, in 1838, and formulated by a Belgian engineer, Gonot, in 1839 (Goldreich, 1913, cited by Zwartendyk, 1971). Since that time,

Jan 1, 1982

By R. A. Vandermeer, J. C. Ogle

The preferred crystallographic orientations (texture) developed in randomly oriented, poly crystalline niobium during rolling were studied by means of X-ray diflraction techniques. The evolution of texture at both the surface and center regions of the rolled strip was carefully examined as a function of increasing defamation throughout the range 43 to 99.5 pct reduction in thickness. Certain aspects of the center texture development in niobium are in agreement with the predictions of a theory by Dillamore and Roberts, but others cannot be explained by the theory in its present form. Above 87 pct reduction by rolling, a distinctly different texture appeared in the surface layers which was unlike the center texture. The present results are compared with previous results obtained from other bcc metals and alloys. RANDOMLY oriented, poly crystalline metal aggregates when plastically deformed to a sufficiently large extent develop preferred orientations or textures. In a recent review article, Dillamore and Roberts1 pointed out that the nature of the developed texture may be influenced by a large number of variables. These include both material variables such as crystal structure and composition and treatment variables such as stress system, amount of deformation, deformation temperature, strain rate, prior thermal-mechanical history, and so forth. From a practical point of view, the control of preferred orientation may often be important for the successful fabrication of metals into usable components. During the past few decades many experiments have been devoted to the study of deformation textures. This work, however, has been confined in large part to metals and alloys that have an fcc crystal lattice. By comparison, bcc metals and alloys have received much less attention, and consequently our understanding of preferred orientations in these materials is only shallow. This state of affairs worsens when it is realized that almost all of our present howledge about this class of materials derives from studies on irons and steels.' The bcc refractory metals, which are relative newcomers to the industrial world, have, on the other hand, been given at best only passing glances in the area of texture development. Our understanding of the evolution of preferred orientations in bcc metals can only remain fairly limited until systematic studies of metals and alloys other than the irons and steels have been carried out and the influence of the many variables has been determined. To that end a program was initiated to investigate in detail texture development in niobium. The present paper reports some of the results of this study. Textures were determined at both the center and surface of strips rolled variously to as much as 99.5 pct reduction in thickness at subzero temperatures. Emphasis in this paper is on texture description and on texture evolution during rolling to progressively heavier deformation. EXPERIMENTAL PROCEDURE The niobium was purchased from the Wah Chang Corp. as a 3-in.-diam electron-beam-melted billet. Chemical analysis indicated the impurities to be less than 300 ppm Ta, 40 ppm C, 10 ppm H, 170 ppm 0, and 110 ppm N. All other impurities were below the limits of detection by spectrochemical analysis. This large-grained billet was fabricated into specimen stock so that a fine-grained randomly oriented grain structure resulted. This was accomplished in three deformation steps alternated with recrystalli-zation anneals of 1 hr at 1200°C in a vacuum of low 10"6 Torr range after each deformation step. The first step was to alternately compress the billet 10 to 20 pct in each of three orthogonal directions. The second step was to compress in only two directions 90 deg apart to produce a 2-in.-sq bar. The final step was to roll this bar 50 pct to give a 1-in. by 2-in. cross section. After the final anneal, metallo-graphic examination showed the material to have an average grain size equivalent to ASTM No. 5 at 100 times (i.e., 0.065 in. diam). Specimens cut from the center and edges of this bar gave no indication of detectable preferred orientation when examined by X-ray diffraction. Samples 1.5 in. long, either 0.625 or 0.750 in. wide, and approximately 0.400 in. thick were machined from this fabricated ingot. The surfaces corresponding to the rolling planes were ground so as to be parallel. The samples were chemically polished in a solution of 60 pct nitric acid and 40 pct hydrofluoric acid (48 pct solution) prior to rolling to remove any cold work introduced in the machining operations. Rolling was accomplished with a 2-high hand-operated laboratory rolling mill that had 2.72-in.-diam rolls. Prior to operation, the rolls were polished with 600 grit paper, cleaned with acetone, and then soaked in a container of liquid nitrogen for several hours. The samples were also soaked in liquid nitrogen prior to rolling and were recooled between each pass. While some slight heating of the samples occurred during rolling, this procedure maintained the sample temperature well below 0°C at all times. The samples were rolled unidirectionally, and the rolling plane surfaces were not inverted during any phase of the operation. The draft per pass averaged between 0.010 to 0.012 in. After 96 or 97 pct reduction the draft was reduced to 0.001 to 0.002 in. per pass. Samples were rolled to various reductions in thickness between 43 and 99.5 pct.

Jan 1, 1969

By H. H. Hasler

THE mining and removal of coal from two or more beds, either simultaneously or consecutively, in vertically adjacent areas have always been matters of concern to mine operators from both operating and recovery points of view. However, with the progressive introduction and use of electrical and mechanical facilities, such problems assume even greater proportions. In this paper typical cases occuring in Cambia County, Pa., are given and procedures whereby such problems may be .greatly reduced, if not entirely eliminated, are suggested. Throughout a considerable portion of the Central Pennsylvania bituminous coal region, particularly in Cambria County (Fig. I), the portion of the region to which references in this paper are made, large areas are encountered where two or more beds of coal occur and have been mined extensively since the earliest days of mining in the county. Generally, operations were commenced in one bed of coal on a property, following which, as conditions appeared to warrant, operations were commenced in another bed or beds on the same property, in some instances by the same operator. Operating results by no means have been uniformly successful, as the following review of some typical cases indicates, partly because of lack of experience in earlier cases and in certain later cases to disregard for the experiences of earlier operators. It is suggested that repetitions of such failures may be reduced largely, if not eliminated entirely, by adherence to a few basic principles founded upon past experiences. Geology and Stratigraphy The geology, stratigraphy, and relief of almost all of Cambria County have been studied and reported at length by the U. S. Geological Survey in its Johnstown, Ebensburg and Barnesboro-Patton Folios and other publications, by the Pennsylvania Geological Survey and by various individuals. All exposed rocks occurring within the boundaries of the county are of sedimentary origin, consisting of alternate beds of sandstone, slate, shale, fireclay, coal, limestone, etc., and all have been classified by the U. S. Geological Survey as extending from the upper strata of the Catskill formation, Devonian system, to and including, in a few hilltop areas, the lower strata of the Monongahela formation, Carboniferous system. Included within that range is the Allegheny formation, Pennsylvania series, which embraces all of the commercially important beds of coal that occur in the county, viz., the A, or Brookville, to the E, or Upper Freeport, both inclusive, shown in Fig. 2. The measures are traversed by a series of anticlines and synclines, extending in a northeasterly and southwesterly direction, which form broad, gently sloping basins (flat to 15 pct pitch, exceptionally to 25 pct). However, the topography of the surface is such that long lines of outcrops of all beds of coal overlying bed B, and to a limited extent bed B also, occur over large areas, a factor which contributed to the early and extensive development of mining activities in the county. Earliest mining developments of commercial importance were made in B, C', D, and E beds of coal, and it is in these beds that the principal mining operations are being conducted. To a limited extent, mining operations also have been conducted in local areas in the A, B rider and C beds. Coal beds being mined today range in thickness from approximately 28 to 60 in. Intervals between the respective beds of coal are variable but conform somewhat to the following general averages: A to B, 60 to 100 ft.; B to C, 50 ft.; C to C', 70 ft.; C' to D, 45 ft.; and D to E, 45 ft. The following are typical mining cases obserced over a period of years in various parts of the county.

Jan 1, 1952

By D. W. Loucks

There is plenty of evidence to indi-cate that at least one of man's chief interests in life is to make himself as comfortable as possible. If you doubt this, just watch the fellow next to you for the next half hour trying to find the most comfortable position that a hard chair has to offer. Comfort, however, does not always mean an easy chair. To some, it may mean a wealth of money; to another, freedom from worry. But to most of us, it means first of all a comfortable atmosphere in which to live, and to a great many of us it probably also means freedom from that annoying task of firing the furnace. Today more than ever before. automatic heat is one improvement that is placed high on everyone's list. Perhaps this is because automatic heating is becoming relatively cheaper. Perhaps it is because of a good publicity campaign on the part of the oil and gas men or maybe it is just that we are getting lazier day by day. At any rate, almost every issue of Better Homes and Gardens, House Beautiful, or your other favorite home magazine carries an article extolling the virtues of this or that automatic heating system. If I were to ask you to name the first thing that came to your mind when I said automatic heat, you would prob-ably say either gas furnace or oil burner. Or if you had just been studying heating systems, you might possibly say heat pump. But chances are you would not mention anything about coal, and yet coal is the most common source of the greatest automatic heat of them all. I say this because coal is the fuel used almost universally by the district heating industry in producing and delivering to certain heavily populated areas heat ready to use at the touch of a valve or the click of a thermostat. Although the industry is over a half century old, it has not experienced the widespread development of other utility industries because of certain limitations which I believe you will realize from the next few minutes discussion. District Heating Operations We may define district heating as any operation where two or more buildings are heated from a central heating plant. The method of heat transfer may be hot water or in some cases warm air, but generally the medium of heat transfer is steam. So universally is steam used that the industry is frequently referred to as the district steam industry. The Allegheny County Steam Heating Co. which operates the district heating system in downtown Pittsburgh is a subsidiary of the Du-quesne Light Co. Although organized in 1912 primarily as a means of securing the electric load of downtown buildings, the service has now become so valuable and so popular that it is no longer considered a necessary adjunct to the electric business but rather a separate business standing on its own feet. Fig 1 shows the layout of the plants and distribution system of downtown Pittsburgh. Two generating plants, one known as the Stanwix and the other as Twelfth Street, supply the area. Each has two boilers with capacity totaling 1,350,000 lb per hour. The Stanwix Plant is supplied coal by truck. The coal is pulverized at the plant and burned as powdered fuel. Coal is supplied to the Twelfth Street Plant also by truck but the boilers arc stoker fired. Over 1 1/2 miles of tunnel house a portion of our main lines, but it requires over twelve miles of pipeline, ranging in size from 32 down to 1 in. in diameter, to supply all our customers. The distribution system consists of two systems in a sense, one high and one low pressure with certain interconnections between the two. Our high pressure system supplies steam up to 125 Ib to some but not all customers, while the low pressure system operates in the range of 10 to 20 psi. Note that the two plants are tied together through large steam mains and that the system to some extent is a loop system, making it possible to have a portion of the line shut, down without interrupting service to any customer. Fig 2 conveys a picture of the extent to which steam service is used in the downtown triangle. The black area indicates the buildings which now use district steam. The dotted area indi-

Jan 1, 1950

By C. Gatlin, F. Armstrong, K. E. Gray

This paper presents some preliminary results of two-dimensional cutting tests of dry limestone samples at utmospheric pressure. Cutting tips having rake angles of + 30°, + 15", 0°, - 15" and - 30" were used to make cuts on Leuders limestone samples at six depths of cut ranging from .005 to ,060 in. at cutting speeds of 15, 50, 109 and 150 ft/min. The vertical and horizontal force components on the cutting tips were recorded with an oscilloscope equipped with a polaroid camera. Motion pictures of the cutting process at camera speeds of 5,000 to 8,000 frames/sec were taken at strategic points in the variable ranges. The movies provide considerable insight into the brittle failure mechanism in rocks. It appears that chip-generating cracks usually have an initial orientation which is related to the resultant of the externally applied forces. The latter part of the crack curves upward toward the free surface being cut, this part being governed by some type of cantilever bending or prying. The linear and angular motion of the loosened chips also indicate the tensile nature of brittle failure. Analyses of the forces on the cutting tips indicate that: (I) relatively small increases in vertical loading result in large cut-depth increases for sharp tips (rake angles 2 0"); (2) tool forces increase at an increasing rate as the rake angle decreases, particularly for rake angles < 0"; and (3), for the range of this study, rate of loading had little effect on the maximum forces. Both the movies and visual inspection of the cuttings indicated that the volume of rock removed by chipping was much larger than that by any grinding mechanism, even for tips having negative rake angles. Cutting size increases with increased cut depth and rake angles, and decreases slightly at high cutting speeds, the depth of cut having by far the most influence. The amount of contact between the rock and the cutting tip was always less than the depth of cut and rarely exceeded 0.010 in. even for cuts of 0.060 in. INTRODUCTION The planing (or slicing) of various materials with a fixed blade has long been practiced by workers in many industries. For example, the farmer&apos;s plow, the carpenter&apos;s plane and the housewife&apos;s paring knife all employ this basic action. The casual observer might suspect that something so common must be quite simple; however, as in all problems involving the failure of materials, such is not the case. Industries concerned with the machining of metals have long studied these problems, and their literature on the subject is voluminous. Despite these efforts, basic knowledge is not very advanced, as may be noted from recent and comprehensive analyses of their literature.12 Metals are more subject to analysis by classical theories of elasticity and/or plasticity than are rocks, since their elastic constants and strengths are reasonably well established in many cases. In spite of this relative "simplicity", Hill9 refaces his discussion with an admission that the mathematical solution to the machining problem is not known. Photoelastic studies of both machining and milling have been performed and are discussed thoroughly by Coker and Filon.4 Rotary drilling of rocks with fixed blade or drag bits has long been practiced by the mining and petroleum industries, and considerable study has been given to defining their cutting action in terms of the pertinent variables. Essentially all the published mechanistic research on drag-bit drilling has been performed by mining engineers and has been concerned only with rocks in the brittle state. Fairhurst5-7 has worked extensively in this area and employed photographic techniques quite similar to those reported here, except at much lower speeds. His studies showed the periodic or cyclical nature of the brittle failure mechanism, in which instantaneous loads on the bit varied from some maximum value to near zero. Goodrichs has presented further data on the subject as well as a qualitative description of the process. Again the postulated mechanism is cyclical, with alternate chipping and grinding periods. The ploughing of coal is a practiced method and has been studied in some detail by English mining engineers."" Their findings have considerable general application to drag-bit drilling. Evans," in particular, has extended Merchant&apos;s metal-cutting theory" to brittle materials with some success, although certain aspects of his theory are open to question. Fish13 has recently summarized nearly all the published works concern-

By Jean Howard

RECENT attempts to produce secondary recrystalli-zation in high-purity iron have given conflicting results. Coulomb and Lacombe1&apos;2 did not find it but Dunn and Walter3,4 did. The latter workers have stated that (100) [001] and/or (110) [001] orientations develop depending on the oxygen content of the annealing atmosphere. This Technical Note records results which are in agreement with Dunn and Walter in so far as it shows that secondary recrystallization can be produced in high-purity iron, but does not confirm that both types of orientation are obtainable. Similar observations have been made on chromium-iron and molybdenum-iron, although when this technique is used on 3 1/4 pct Si-Fe, both types are obtained as in the work of Dunn and alter.&apos; Pure iron strip was cold-rolled from sintered compacts prepared from Carbonyl Iron Powder-Grade MCP of the International Nickel Co. (Mond) Ltd. The powder contains about 0.5 pct 0, 0.01 pct C, 0.004 pct N, (0.002 pct S, $0.005 pct Mg and Si, and 0.4 pct Ni—that is, it is substantially free from metallic impurities other than nickel, which is thought to be unimportant in the present work. The iron powder was (a) pressed at 25 tons per sq in. into blocks measuring 3 by 1 by 0.3 in., (b) deoxidized in hydrogen (dewpoint -60°C) by heating first at 350°C and then at 600° C until the dewpoint returned to -60°C at each temperature and (c) sintered in hydrogen (dewpoint -40°C) at 1350°C for 24 hr. (when dewpoint is referred to in this Note, it is the value as measured on the exit side of the furnace). The sintered compacts were cold-rolled to 1/8 in., annealed in hydrogen (dewpoint -60°C) at 1050°C for 12 hr and cold-rolled to 0.004, 0.002, and 0.001 in. with inter-anneals at 900°C for 5 hr and a final reduction of 50 pct. Final annealing of strip between alumina or silica plates at 875" to 900°C in hydrogen with dewpoints of -20°, -55" and -80°C produced secondary grains with the (100) in the rolling plane; the extent of secondary recrystallization was greatest when the dewpoint was -55°C. Annealing in a vacuum of 2 x 10"5 mm Hg at the same temperature produced no secondary recrystallization at all. With strip thicker than 0.002 in. very few secondary crystals developed whatever the conditions of annealing. Using a processing schedule somewhat similar to that described above, secondary recrystallization was produced in two bcc alloys of iron, viz. 80 pct Fe + 20 pct Cr and 96 pct Fe + 4 pct Mo. The former was reduced to final thicknesses of 0.001 to 0.004 in. and the latter to final thicknesses of 0.001 to 0.016 in. With the chromium-iron, a final anneal at 1250°C (found to be the most effective temperature for developing secondary crystals in the 0.004-in material) with a dewpoint of -25°C produced a greater degree of secondary recrystallization than with dewpoints of -50°C or -20°C. Secondary crystals developed in strips of all thicknesses from 0.001 to 0.004 in. Final annealing in vacuum produced no secondary crystals at all. For the molybdenum-iron a temperature of 1200°C was most effective. It was found that a dewpoint of -50°C during the final anneal gave better results than a dewpoint of -25 "C on the 0.008 in. material. Final annealing in vacuum gave slightly worse results than annealing in hydrogen with a dew-point of -50°C. Secondary crystals were developed in strips of all thicknesses up to 0.008 in. The experiments show that the extent of secondary recrystallization is a maximum for certain critical values of oxygen content of furnace atmosphere and annealing temperature, and that these values are different for different alloys. The thinner the material, the less critical these values are. The general conclusions are that secondary recrystallization can be obtained in high-purity iron, chromium-iron, and molybdenum-iron, using a processing schedule similar to that which will cause the phenomenon to take place in high purity 3 1/4 pct Si-Fe. Unlike the silicon-iron, however, only the (100) (0011-- orientation has been produced in these alloys, irrespective of the temperature of final annealing and the oxygen content of the furnace atmosphere. The information used in this Note is published by permission of the Engineer-in-Chief of the British Post Office.

Jan 1, 1962

By B. M. Larsen

Attempting to review the fundamental aspects of segregation in steel ingots of all types in a paper of reasonable length, we encounter two difficulties: (I) the fact that a large number of different physical and chemical effects are involved, and (2) rather incomplete and confusing evidence on certain aspects of detail and mechanism in the freezing process in which the segregation effect is involved. The best solution seemed to be to link together most of the underlying factors into a simplified theoretical picture that appears to the writer to explain most of the observed data, in the hope that this will serve as a reasonably good target for discussion and criticism. Segregation effects, especially in steel ingots or castings, are often divided into " microscopic" and "macroscopic," depending on whether the variations in concentration of solutes or dissolved elements in the iron occur as: (I) a periodic variation over the small distances between the nuclei and the surfaces of the primary grains, or (2) as a larger scale effect involving concentration gradients over distances of the order of several inches, more or less. The reason for this somewhat artificial division is, of course, that it is only the macroscopic scale effect that has much practical importance. About the only effect of practical importance that results from microscopic segregation is the banded structure often left in rolled sections, and even this is relatively harmless in most cases. However, the causes of microscopic segregation also untlerly the larger scale effect, so we must first consider matters such as the formation and growth of crystal nuclei, selective freezing and diffusion, and others that are fundamental to all sepregation effects. Undercooling and Nuclei Formation It is probable that although the degree of undercooling is small in iron, as in metals in general, a certain amount of it takes place, and also that the number of crystal nuclei increases very rapidly with increased undercooling below the liquidus temperature. In practical terms this means that the nuclei number illcreases very rapidly with increased cooling or freezing rate, thus being dependent on the rate of heat flow out from the zone of crystallization. Temperature Gradients and Heat Dissipation during Freezing Each pound of steel evolves about 100 B.t.u. when freezing. In addition to this, the temperature gradient in the solidified portion (required to dissipate the heat as freezing progresses into the axis) necessitates a loss of heat required to cool the solid metal below its freezing range, which is equivalent to an amount of not so much less in magnitude. In a 5-ton ingot, the total would include about one million B.t.u. for freezing alone and about 0.4 to 0.5 million B.t.u. for the gradient, up to the end of the freezing period. Thus the rate of freezing depends primarily on the rate of heat dissipation. In the ordinary ingot shapes, the axial rate of growth of the solid

Jan 1, 1945

By B. M. Larsen

ATTEMPTING to review the fundamental aspects of segregation in steel ingots of all types in a paper of reasonable length, we encounter two difficulties: (I) the fact that a large number of different physical and chemical effects are involved, and (2) rather incomplete and confusing evidence on certain aspects of detail and mechanism in the freezing process in which the segregation effect is involved. The best solution seemed to be to link together most of the underlying factors into a simplified theoretical picture that appears to the writer to explain most of the observed data, in the hope that this will serve as a reasonably good target for discussion and criticism. Segregation effects, especially in steel ingots or castings, are often divided into " microscopic " and " macroscopic," depending on whether the variations in concentration of solutes? or dissolved elements in the iron occur as: (I) a periodic variation over the small distances between the nuclei and the surfaces of the primary grains, or (2) as a larger scale effect involving concentration gradients over distances of the order of several inches, more or less. The reason for this somewhat artificial division is, of course, that it is only the macroscopic scale effect that has much practical importance. About the only effect of practical importance that results from microscopic segregation is the banded structure often left in rolled sections, and even this is relatively harmless in most cases. However, the causes of microscopic segregation also underly the larger scale effect, so we must first consider matters such as the formation and growth of crystal nuclei, selective freezing and diffusion, and others that are fundamental to all segregation effects. UNDERCOOLING AND NUCLEI FORMATION It is probable that although the degree of undercooling is small in iron, as in metals in general, a certain amount of it takes place, and also that the number of crystal nuclei increases very rapidly with increased undercooling below the liquidus tempera¬ture. In practical terms this means that the nuclei number increases very rapidly with increased cooling or freezing rate, thus being dependent on the rate of heat flow out from the zone of crystallization. TEMPERATURE GRADIENTS AND HEAT DISSIPATION DURING FREEZING Each pound of steel evolves about 100 B.t.u. when freezing. In addition to this, the temperature gradient in the solidified portion (required to dissipate the heat as freezing progresses into the axis) necessitates a loss of heat required to cool the solid metal below its freezing range, which is equivalent to an amount of not so much less in magnitude. In a 5-ton ingot, the total would include about one million B.t.u. for freezing alone and about 0.4 to 0.5 million B.t.u. for the gradient, up to the end of the freezing period: Thus the rate of freezing depends primarily on the rate of heat dissipation. In the ordinary ingot shapes, the axial rate of growth of the solid

Jan 1, 1944

By J. S. Marsh

Joseph Priestley prepared oxygen on Aug. I, 1774, and noted with great surprise "that a candle burned in this air with a remarkable brilliant flame." On Aug. 2, 1774, some ironmaker possibly began to wonder if this substance could be used to increase his rate of production; at any rate, there is no disputing the fact that the notion of using oxygen for steelmaking in concentrations greater than that available in great abundance—as air—has been in existence for years. Action was delayed by the lack of enough oxygen at a cost within reach of the steelmaker. Within the last several years enough has been available to permit large-scale tests of its use for both combustion, with which this paper is concerned, and for decarburization. The literature is now enormous and easily available; it is sufficient here to cite three items of historic importance in that all are about 25 years old and in that all are remarkably consistent as far as they go, with what is known today.1,2,3 Significance of High-temperature Heat The principal function of the open-hearth furnace is to supply sufficient high-temperature heat to melt the charge and then to increase its temperature to a range suitable for tapping, ordinarily in the neighborhood of 2900°F. That heat is required to make steel is understood by everybody; however, there seems to be some confusion now and then about the significance of high-temperature heat. Transfer of energy—and heat is energy— is always from a point of higher potential to a point of lower potential and, other things being equal, the greater the potential difference, the greater is the rate of transfer of energy. In the open hearth the flame, of course, is the high-potential source. Perhaps the most satisfactory approach is through the notion of theoretical flame temperature, which is the ratio of heat input to the heat content of the combustion products,* the former is composed mainly of heat of combustion of the fuel plus sensible heat of the fuel plus sensible heat of the combustion air. Thus, flame temperature can be increased by increasing the value of the numerator, by decreasing the value of the denominator, or both. The first method is as old as the open-hearth process and, of course, makes use of preheated air; its possibilities have been by no means exhausted. The second method can be put into effect only by changing the composition of the combustion air, since the combustion of a given quantity of fuel produces a definite quantity of product, and since the denominator includes the non-reactive fraction of the air, principally nitrogen. In other words, the denominator consists of the volume of exit gas multiplied by its heat capacity and that volume consists of carbon dioxide and water vapor as reaction

Jan 1, 1949

By J. S. Marsh

Joseph Priestley prepared oxygen on Aug. I, 1774, and noted with great surprise "that a candle burned in this air with a remarkable brilliant flame." On Aug. 2, 1774, some ironmaker possibly began to wonder if this substance could be used to increase his rate of production; at any rate, there is no disputing the fact that the notion of using oxygen for steelmaking in concentrations greater than that available in great abundance—as air—has been in existence for years. Action was delayed by the lack of enough oxygen at a cost within reach of the steelmaker. Within the last several years enough has been available to permit large-scale tests of its use for both combustion, with which this paper is concerned, and for decarburization. The literature is now enormous and easily available; it is sufficient here to cite three items of historic importance in that all are about 25 years old and in that all are remarkably consistent as far as they go, with what is known today.1,2,3 Significance of High-temperature Heat The principal function of the open-hearth furnace is to supply sufficient high-temperature heat to melt the charge and then to increase its temperature to a range suitable for tapping, ordinarily in the neighborhood of 2900°F. That heat is required to make steel is understood by everybody; however, there seems to be some confusion now and then about the significance of high-temperature heat. Transfer of energy—and heat is energy— is always from a point of higher potential to a point of lower potential and, other things being equal, the greater the potential difference, the greater is the rate of transfer of energy. In the open hearth the flame, of course, is the high-potential source. Perhaps the most satisfactory approach is through the notion of theoretical flame temperature, which is the ratio of heat input to the heat content of the combustion products,* the former is composed mainly of heat of combustion of the fuel plus sensible heat of the fuel plus sensible heat of the combustion air. Thus, flame temperature can be increased by increasing the value of the numerator, by decreasing the value of the denominator, or both. The first method is as old as the open-hearth process and, of course, makes use of preheated air; its possibilities have been by no means exhausted. The second method can be put into effect only by changing the composition of the combustion air, since the combustion of a given quantity of fuel produces a definite quantity of product, and since the denominator includes the non-reactive fraction of the air, principally nitrogen. In other words, the denominator consists of the volume of exit gas multiplied by its heat capacity and that volume consists of carbon dioxide and water vapor as reaction

Jan 1, 1949

By T. S. West

Completion and production data presented for three wells in the Oakville area of Live Oak County, Texas, which were completed near the gas-oil or water-oil contact, indicate that coning may not be as prevalent a cause of failure in such cases as is commonly assumed. Failure in the cases discussed is indicated to be due instead to: (I) erosion of the formation, (2) flowing out of mud filter cake, or (3) failure of the cement. An open-hole gravel-pack type of completion procedure is proposed for preventing failures of this kind by preventing movement of all solid material in the space in which completion is made. Various combinations of layers of gravel, sand, and cement are utilized for this purpose. Experimental results and theoretical discussion as to the applicability of gravel pack completion are included. Introduction This paper is primarily a study of the reasons for failure of oil-well completions near the gas-oil or oil-water contact, and suggests a procedure for increasing the efficiency of this type of completion. The value of improvement in completion effectiveness near the gas or water zone is not confined, however, to wells of relatively thin oil columns. Thick oil columns become thin as depletion progresses. It would seem to follow that the minimum distance from the gas or water zone at which completion can be made in a new well indicates the limit to which depletion may be carried in a well having an oil column of any initial magnitude. Only four ways can be postulated in which high gas-oil or water-oil ratio can initially occur if the zone exposed for production is within the oil column: 1. Failure of the cementing material. 2. Vertical coning. 3. Failure along the boundary between the cement and the wall of the well. 4. Failure of the formation comprising the wall of the well. Cementing materials such as portland cement and plastics have reached a high stage of development. Failures of this type are probably due almost always to extraneous causes such as mud contamination rather than to faulty cementing material. Vertical coning can and obviously does occur. However, the usual occurrence of thin impermeable streaks in sand sections and the success with which open-hole drill-stem tests can be made near the gas-oil contact suggest that over-all effective vertical permeability, and in turn vertical coning, is less prevalent than frequently is assumed. Much has been written on failure by flowing out of the mud filter cake between cementing material and the formation. A filter cake is always present if, prior to cementing, mud has come in contact with a permeable formation at pressures exceeding the pressure head of the fluid it contains. Mechanical methods are in use for removing filter cake during the cementing operation? which undoubtedly are of

Jan 1, 1947

By T. S. West

Completion and production data presented for three wells in the Oakville area of Live Oak County, Texas, which were completed near the gas-oil or water-oil contact, indicate that coning may not be as prevalent a cause of failure in such cases as is commonly assumed. Failure in the cases discussed is indicated to be due instead to: (I) erosion of the formation, (2) flowing out of mud filter cake, or (3) failure of the cement. An open-hole gravel-pack type of completion procedure is proposed for preventing failures of this kind by preventing movement of all solid material in the space in which completion is made. Various combinations of layers of gravel, sand, and cement are utilized for this purpose. Experimental results and theoretical discussion as to the applicability of gravel pack completion are included. Introduction This paper is primarily a study of the reasons for failure of oil-well completions near the gas-oil or oil-water contact, and suggests a procedure for increasing the efficiency of this type of completion. The value of improvement in completion effectiveness near the gas or water zone is not confined, however, to wells of relatively thin oil columns. Thick oil columns become thin as depletion progresses. It would seem to follow that the minimum distance from the gas or water zone at which completion can be made in a new well indicates the limit to which depletion may be carried in a well having an oil column of any initial magnitude. Only four ways can be postulated in which high gas-oil or water-oil ratio can initially occur if the zone exposed for production is within the oil column: 1. Failure of the cementing material. 2. Vertical coning. 3. Failure along the boundary between the cement and the wall of the well. 4. Failure of the formation comprising the wall of the well. Cementing materials such as portland cement and plastics have reached a high stage of development. Failures of this type are probably due almost always to extraneous causes such as mud contamination rather than to faulty cementing material. Vertical coning can and obviously does occur. However, the usual occurrence of thin impermeable streaks in sand sections and the success with which open-hole drill-stem tests can be made near the gas-oil contact suggest that over-all effective vertical permeability, and in turn vertical coning, is less prevalent than frequently is assumed. Much has been written on failure by flowing out of the mud filter cake between cementing material and the formation. A filter cake is always present if, prior to cementing, mud has come in contact with a permeable formation at pressures exceeding the pressure head of the fluid it contains. Mechanical methods are in use for removing filter cake during the cementing operation? which undoubtedly are of

Jan 1, 1947

By J. S. Marsh

JOSEPH PRIESTLEY prepared oxygen on Aug. 1, 1774, and noted with great surprise "that a candle burned in this air with a remarkable brilliant flame." On Aug. 2, 1774, some ironmaker possibly began to wonder if this substance could be used to increase his rate of production; at any rate, there is no disputing the fact that the notion of using oxygen for steelmaking in concentrations greater than that available in great abundance-as air-has been in existence for years. Action was delayed by the lack of enough oxygen at a cost within reach of the steelmaker. Within the last several years enough has been available to permit large-scale tests of its use for both combustion, with which this paper is concerned, and for decarburization. The literature is now enormous and easily available; it is sufficient here to cite three items of historic- importance in that all are about 25 years old and in that all are remarkably consistent as far as they go, with what is known today.1,2,3 SIGNIFICANCE OF HIGH-TEMPERATURE HEAT The principal &apos;function of the open-hearth furnace is to supply sufficient, high-temperature heat to melt the charge and then to increase its temperature to a range suitable for tapping, ordinarily in the neighborhood of 2900°F. That heat is required to make steel everybody; however, there seems to be some confusion now and then about the significance of high-temperature heat. Transfer of energy-and heat is energy is always from a point of higher potential to a point of lower potential and, other things being equal, the greater the potential difference, the greater is the rate of transfer of energy. In the open hearth the flame, of course, is the high-potential source. Perhaps the most satisfactory approach is through the notion of theoretical flame temperature; which is the ratio of heat input to the heat content of the combustion products,* the former is composed mainly of heat of combustion of the fuel plus sensible heat of the fuel plus sensible heat of the combustion air. Thus, flame temperature can be increased by increasing the value of the numerator, by decreasing the value of the denominator, or both. The first method is as old as the open-hearth process and, of course, makes use of preheated air; its possibilities have been by no means exhausted. The second method can be put into effect only by changing the composition of the combustion air, since the combustion of a given quantity of fuel produces a definite quantity of product, and since the denominator includes the non-reactive fraction of the air, principally nitrogen. In other words, the denominator consists of the volume of exit gas multiplied by its heat capacity and that volume consists of carbon l is understood by dioxide and water vapor as reaction

Jan 1, 1948