Search Documents

By K-O. Mickelsson, S. Töyrä, H. Esbensen

Accurate information of physical, chemical and metallurgical quality characteristics such as moisture content, iron grade and particle size are crucial for successful process control and for producing products within customer specifications. Correct moisture content of pellet feed is an important variable for successful balling of iron ore pellets and to minimize power consumption in the sintering process. Control of the filtering process in the pelletizing plant is therefore essential for both productivity and high product quality. The current measurement systems for moisture content at LKAB are based on two types of manual grab sampling, subsequently analyzed with rapid moisture determination methods. Previous studies of the measurement systems have indicated high sampling variability resulting in lowered possibilities for successful process control. The objective of the present study is to evaluate an alternative filter sampling approach and testing of on-line Infra-Red analysis (IR-analysis). On-line IR-analysis has the advantage of eliminating physical sample extraction and allowing for continuous monitoring of moisture content. However, this approach is sensitive to the surrounding environment, making careful calibration and control crucial for the quality of measurement results. Furthermore, as IR-sensors only target the surface of the conveyed pellet feed, several incorrect sampling errors need to be considered and counteracted to eliminate sampling bias and reduce the remaining measurement variability. Variographic characterization was applied to the two current grab sampling approaches of combined filtered material, to the alternative filter sampling method, and to the On-line IR-analysis. The results indicate that both the sampling of separate filters (using composite sampling and ISO-standardized moisture analysis), as well as a calibrated and well- maintained IR-sensor can improve the relative variability significantly, by lowering the total measurement system variance from 60% to 25%.

Jan 1, 2018

By E. Guerrini, M. Maccagni, J. Nielsen

"The solution for the treatment of the EAFD has not yet been fully achieved. Some of this dust has still not found an appropriate final destination. Large consortium treatment plants are quite expensive both in terms of investment and operating cost. Meanwhile, the tolling expenses for steel production companies are becoming very important, causing them to look for alternatives. Some steel plants are looking to close their production loop by internal treatment of their dust. Some years ago, Engitec began studying the coupling of the EZINEX® Process, an ammonium chloride electrolysis to recover the zinc contained in the EAFD, with the INDUTEC® Process, a pyro process based on an induction furnace that can convert EAFD into a C.Z.O. similar to the Waelz oxide. The combination of these two processes provides an alternative to the existing treatment options and is particularly interesting for relatively small capacities. In this paper, we would like to give the latest update about these two processes and their possible integration INTRODUCTION Zinc is contained in numerous wastes and secondary raw materials that can be thought of as high zinc concentrate mines. This is a very interesting source of Zn that is typically easily exploitable. Unfortunately, only a portion of these materials are currently processed to recover the metal value, while stabilized or unstabilized landfilling is often the final destination. Pyrometallurgical processes are mainly used to convert the zinc into crude zinc oxide (CZO). The various processes are very similar and characterized by the fact that the zinc bearing materials are usually submitted to a thermal treatment [1] in which the zinc is reduced, vaporized and re-oxidized producing CZO. This material not only contains zinc oxide, but also relatively high concentrations of heavy metals. Many potential CZO sources, such as electric arc furnace dust (EAF), galvanizing ashes, brass foundry and converters fumes also contain chlorides, fluorides and alkali metals that will transfer to the CZO. The classic example is the Waelz oxide [2]. This CZO is an intermediate product that must be transformed into zinc salts or zinc metal. Until now, the conversion to zinc metal is done through two main processes: the sulphate leaching and electrowinning system and the Imperial Smelting Process (ISP). ISP is facing a crisis for technical and economic reasons that has led to the closing of most of the existing plants. In any case, before being fed to one of these two processes, the CZO must be treated to eliminate or reduce some of the contained impurities. In particular, the halides are most harmful to these processes."

Jan 1, 2018

By Ronel du Plessis, John C. Davidtz, Jan D. Miller

Recent results from electrochemical measurements demonstrate that trithiocarbonate (TTC) collectors are more readily oxidized to their corresponding dithiolates than the dithiocarbonate/xanthate (DTC) collectors. Based on the traditional analysis of collector adsorption, trithiocarbonates might then be expected to be effective for bulk sulfide mineral flotation. Previous bench-scale flotation research had shown that TTC collectors are very effective for the flotation of copper sulfide minerals and PGM (platinum group metal) sulfide minerals. More recently, the TTC collectors were evaluated for auriferous pyrite recovery in benchscale plant scale flotation testing in the United States and in plant tests at Anglogold in South Africa. TTC collectors were also applied in bench-scale testing of a PGM ore. In each case an improved separation efficiency was realized. Fundamental studies at the University of Utah examining the effect of collector structure (functional group, -O-CS2 versus .S-CS2), specifically with respect to auriferous pyrite flotation, are in progress. The effect of collector structure was evaluated with air as well as nitrogen as the flotation gas medium. Experimental techniques utilized included electrochemically controlled contact angle measurements to evaluate mineral hydrophobicity and infrared spectroscopy to explain collector adsorption phenomena at the mineral surface.

Jan 1, 2003

By A. N. Zagorodnyaya, T. N. Bukurov, Z. S. Abisheva, A. S. Sharipova

"The paper describes the results of stripping of copper production dusts by leaching with aqueous soda, nitric acid solutions and recovery from solutions resulting in the production of lead sulphate, tribasic lead sulfate (TBLS), ammonium perrhenate, zinc, copper-cadmium cake.The combination of two stripping operations under chosen optimal conditions allows the recovery of 98% rhenium, 82% lead, 92 % copper, and 96% zinc and cadmium each. The major amount of rhenium (~ 80%) is recovered at the carbonization stage, and other metals - at the nitric acid leaching stage.Lead sulfate was precipitated by mixing solutions resulting from carbonization and leaching. Tribasic lead sulfate was produced by dissolving lead sulfate in sodium hydroxide solutions. Rhenium was recovered from mother liquor resulting from lead sulfate precipitation by liquid-liquid extraction and zinc was recovered from raffinates. Trialkylamine (TAA) was used as an extractant for rhenium recovery and di-2- ethylhexylphosphoric acid was used for zinc recovery. Optimal liquid-liquid extraction parameters have been defined allowing the recovery of 96% rhenium in crude ammonium perrhenate and 94% zinc in sulfuric acid solution. Based on the experimental data, the flowchart for dust processing to produce salable products - lead, rhenium, zinc salts has been suggested."

Jan 1, 2003

By Kozlov Andrey, Matveeva Tamara

"The results of mineralogical and technological studies of platiniferous dunites from Svetloborsky zonal massif (Urals platinum belt) are presented and the basic typomorphic signs of productive mineral assemblages are substantiated. The characteristic features of platinum ore mineralization are revealed: a wide range of iron-platinum alloys, enrichment of ore-formed system by the elements Os, Ir, Rh and activity of the S and As in it, intrusion of Fe-Ni sulfides in platinum and its fusion with magnetite. More than 80% of PGM mineral grains has size less than 100 microns, that determines the possibility of significant losses of platinum in the process of gravity separation and the need for additional recovery processes for small and fine fractions of platinum tailings and sludge products. Summarized results of laboratory tests of small-volume sample processing of platiniferous dunites are presented and the processing flow sheet is developed and tested. The flow sheet incorporates several stages, including stage-wise grinding and gravity separation of ore using the centrifugal concentrator Knelson KS-MD for differently sized material and flotation treatment of tailing products using new classes of reagents for additional recovery of PGM fines."

Jan 1, 2014

By S. L. Gubin, T. V. Ignatova, A. V. Levshin, D. O. Sharkovsky

"Flotation process applied for concentration of unoxidized ferruginous quartzites by PJSC Mikhailovsky GOK (MGOK) is based on wet magnetic separation of strong magnetic minerals. However quality of the resulting concentrate (Fe65-66%) is insufficient for production of metallics. Quality upgrade of magnetite concentrate via flotation has been implemented by MGOK to produce premium quality magnetite concentrate.Flotation is a challenging process due to sensitivity to varied amounts of reagents, fine and coarse mineral ratio, particle contact (retention) time and temperature of feed. Tomah’s PA-14 reagent (USA) has proven efficient for application in flotation of MGOK’s magnetite concentrate.Objective of this work is to select and prove applicability of selective agents for flotation upgrade of magnetite iron ore concentrate.Series of flotation tests has been carried out with application of new highly selective collecting agents produced by Akzo Nobel (Sweden), Clariant (Germany) as well as Akzo Nobel’s and Tomah’s cationic collector mix to improve performance efficiency of flotation process. Tomah’s flotation agents and Akzo Nobel’s Lilaflotproved to be the most effective for purposes of concentrate quality upgrade to Fe69.0% via flotation.Testing Method: Following scientific research methods were applied for testwork: system analysis, mathematical statistics, observation, comparison, trial (experiment).To determine key process factors a series of pilot tests was carried out. Most of the testwork was performed by PJSC Mikhailovsky GOK’s Central Process Laboratory.Work Results:-optimized flotation performance modes were defined to ensure production of three types of low-silica concentrate, i.e. containing SiO25%, SiO24% and below SiO23% by weight. Most efficient selective agents applicable for flotation have been defined. Mixture of higher aliphatic amines has proven to intensify selective flotation of quartz. It enables higher yield of chamber product maintaining desired quality of concentrate.Achieved process operation and performance factors have been revaluated.Value for Advancement and Expansion of Mineral Processing:Flotation of concentrate has enabled expansion of PJSC Mikhailovsky GOK’s production capacity, improved production quality, helped to maintain sustainability and competitive advantage of the company."

Jan 1, 2018

By J. B. Yianatos

A practical an interactive model to describe the operation of a flotation bank of mechanical cells was developed based on the hydrodynamic and metallurgical characterization of large industrial flotation cells. Thus, the mineral grade and recovery, as well as the stream properties along the flotation bank can be described in terms of the operating variables. The model was built considering the flotation bank as a distributed system, so the solution for the water and solids mass balances, per size classes, for each single cell, are sequentially solved. Also, each cell was described by two distinct zones, the collection zone characterized by the flotation rate constant and the froth zone characterized by the froth recovery. The mineral feed was described in terms of the mineral species and particle size classes, using a rectangular flotation rate constant distribution. Also, the effect of changing the actual operating variables (air flowrate, pulp level, pulp density, pulp flowrate, etc.) on the mineral collection process, in the collection (pulp) zone, was considered downstream along the bank. The froth recovery of floatable mineral has been estimated by measuring the mass flowrate of particles entering the froth by true flotation together with the concentrate mass flowrate (ton/h). The mass flowrate of collected particles at the pulp/froth interface level was calculated from direct measurement of bubble load (ton/m3) and gas flowrate (m3/h). Flotation recovery is mainly related to the froth depth and air flowrate. All parameters considered in the model have been adjusted from direct measurements in plant site. Also, the effects of other operating variables such as reagents dosage, top of froth grade, or froth discharge velocity are presently under study. This procedure has been tested using data from industrial rougher operations consisting of flotation banks with 5 cells to 9 cells in series, and different cell sizes, such as 45m3, 130m3, 160m3 and 250m3. Thus, it has been shown that the model approach is a powerful tool for flotation cells diagnosis, operation and development of new control strategies, as well as, to evaluate the effect that de-sign and operating variables have upon the collection and froth zones performance in large flotation cells.

Jan 1, 2014

The concept of the Unified Comminution Model (UCM) was presented at the 23rdIMPC. The model utilises computational techniques to calculate the mechanical environment in any comminution device, and then incorporates the outcomes from rock breakage tests to predict the product from a device. The model is fully mechanistic, and incorporates the capability to simulate novel equipment. This paper presents the progress on the first application of this concept to applied comminution equipment. This novel comminution model aims to integrate all comminution models within a single struc-ture. This will provide a step change in the predictive power of comminution models, and include a wide range of particle properties that will enable it to be linked to the upstream and downstream process of mining and recovery. Major advances over current models will be the capability to predict liberation, preferential grinding, performance of new and novel devices, and to have power as an integral driver of the comminution simulation process. The methodology and model structure have been developed. An equation within a population balance framework has been derived as the basis for the UCM. A set of SAG mill pilot has been used as the first test case. The breakage characteristics of the ore have been extensively tested utilising a new range of breakage tests required by the rigorous UCM structure. The mill was simulated with the EDEM - DEM software. A partial test simulation of the pilot SAG mill has been conducted. This serves to demonstrate the feasibility of this modelling technique, but still lacks important ore characterisation components that are under development. The study has raised a number of significant challenges to the accepted understanding of the comminution process. Through addressing these challenges considerable insight has been gained into the energy environment in mills and the requirements of breakage testing. The ore characterisation methods and energy transmission derived from DEM simulations remain as major research items.

Jan 1, 2014

By L. Bbosa

Positron Emission Particle Tracking (PEPT) and the Discrete Element Method (DEM) are used to investigate Power Draw in a laboratory scale tumbling mill. The mill is run dry in batch mode at different speeds using mono-size charge of glass beads, and is mounted along with a torque transducer to measure power. Particle tracking information from PEPT is used to reconstruct the motion of glass beads and infer the overall charge behavior, while DEM is employed to simulate particle motion and interaction, with collision mechanics calculated using the Hertz-Mindlin contact model. For PEPT and DEM data, the product of torque and average angular velocities in discrete cells are accumulated to obtain mill power. This method is found to be within statistical agreement with measured power for all tests. Spatial distributions plotted from this approach highlight the regions of the mill that draw the greatest power. A second technique to obtain Power Draw from DEM data which sums particle forces against the mill geometry is similarly found to accurately predict mill power with lower statistical error. Keywords: Power Draw, PEPT, DEM

Sep 1, 2012

By Ljudmil S. Grigorov, Eric Forssberg, Hanumantha Rao Kota, Robert J. Pugh, Lidia B. Alexandrova

"We have used the microscopic thin balance developed by Scheludko at al. (1970) technique to study the stability and interactions within the thin film between the silica surface and air bubble with (i) a long chain C10 amine and (ii) a cationic/anionic surfactant systems consisting of mixtures of a long straight C10 chain amine with long straight chain C8, C10 and C12 sulfonates. It was found that the mixed surfactants caused lower contact angles, lower rates of the thin aqueous film rupture and longer film lifetime, compared to the pure amine system.This behavior was explained by the initial strong adsorption of positively charged interfacial complexes from the mixed surfactant system at the air/solution interface followed by adsorption at the silica interface. It was also shown that the chain length compatibility between the anionic and cationic surfactants controls the strength of the interfacial complex, determining an inhibition in the thin film rupture and dewetting of the film. The rupture mechanism was explained by an earlier established heterocoagulation mechanism between the positively charged air/solution interface and the solution/silica interface which remained negatively charged. The formation of the interfacial complex at the air/solution interface was confirmed by using surface tension data."

Jan 1, 2003

By Smuts. E. M.

This paper describes a methodology used to develop a numerical model for the study of particulate suspension rheology. Initially, Computational Fluid Dynamics (CFD) models of different rheometer geometries were tested with both a Newtonian fluid (water), and a non-Newtonian Herschel-Bulkley slurry. Rheograms were reproduced from these models and compared to experimental values. Once a single-phase model had been validated, a coupled model combining CFD and the Discrete Element Method (DEM) was created. Two open source software packages were chosen. CFD is implemented using Open FOAM®, and DEM using LIGGGHTS. These two different codes were coupled via another program called CFDEM. This coupled model is currently capable of modeling spherical particles in a suspending liquid. DLVO forces have been included in some models to account for inter-particle forces due to the surface charge on the particles. The coupled model is currently being validated. Preliminary results show good qualitative behavior of the model. Keywords: rheology, cfd, dem, suspensions, modeling

Sep 1, 2012

By V. K. Gupta

Selection of mill size for reducing a feed material of a given size to the desired product size is generally based on the specific energy estimate obtained from Bond test. Over the last thirty years or so, an attempt has been made to develop a more accurate and powerful alternative approach based on the characterization of the particle breakage kinetics and material transport through the mill over a range of operating conditions of interest and correlating the degree of size reduction achieved with the net specific energy input to the mill. Particle breakage kinetics are described in terms of the specific grinding rate and breakage distribution parameters for the individual size fractions. Precise estimates of these parameters and the net energy input to the test ball mill (a laboratory or pilot scale mill) are important for development of desired energy-size correlations. In this context, three tasks are important: (a) preparation of the feed charge, (b) design of batch grinding experiments and (c) computational technique used for estimation of the breakage rate and breakage distribution parameters. This paper highlights several aspects of these three tasks that have been overlooked by researchers working in this field, and describes a more appropriate approach for estimation of model parameters and specific energy input. Several examples are included based on the data available in the literature and those generated in our laboratories to illustrate important points.

Sep 1, 2012

By Alex Joseph

A tertiary amine containing polyamine in its back bone was grafted to exfoliated graphite oxide by means of a series of chemical reactions.The synthesized amine functionalized polyaniline grafted to exfoliated graphite oxide (EGAMPANI) was characterized using various techniques such as, FTIR, TGA, Raman, and X-Ray diffraction.The synthesized EGAMPANI was blended with carbon paste electrode, and used to study the response of Hg2+ in acetate buffer solution.Preliminary analysis showed that the anodic current intensity using the EGAMPANI modified electrode was higher during a potential sweep and 10-4 M concentration of mercury could be detected which could be improved to 10-6 M using anodic stripping voltammetric technique. Keywords: metal sensor, exfoliated graphite oxide, functionalization, polyaniline

Sep 1, 2012

By Roberto Galéry, Braz J. C. Filho, Marcelo M. Stopa, Douglas B. Mazzinghy, Priscila M. Esteves

"The purpose of the research is to monitor ball mill filling by means of signals usually measured in its electrical drive. The method is based on the mill torque estimated from rotor speed and induction motor stator voltage and currents. New signal processing is presented in both time and frequency domain for measurements in a dry laboratory ball mill. Statistical analysis is applied to time series resulting in good correlation to mill filling. Fast Fourier Transform (FFT) and power spectral density (PSD) also resulted in an accurate filling indicator. The proposed method does not need any sensor to be installed directly on the mill and requires only sensors usually available for motor control purposes. The experimental results showed that the method have potential to be used to construct an automatic system for monitoring operational variables in ball mills. The aim of this monitoring is to improve energy efficiency, reliability and productivity.INTRODUCTION Recently, a great number of papers have pointed the importance of ball mill filling monitoring and also of grinding control (Lu, et al., 2014) (Ramasamy, et al., 2005) (Tsamatsoulis, 2014) (Zhou, et al., 2009). Additionally, great amount of control techniques have also been presented with several complexity degrees (Tsamatsoulis, 2014). According to Eremenko (2015) the lack of effective and accurate methods for fill level measurement is the main reason that makes mill optimal control so complicated. It happens because nonlinearity, long time delay and time varying features of the ball mill turns difficult to develop a truly efficient method for monitoring filling. At the same time, fill level has a determining role in charge motion and consequently on particle breakage. For low levels of filling many energy is expended in impacts with very low breakage efficiency. Those impacts can also damage mill liner. In contrast, high levels of filling causes damping effects that reduces breakage and can also affect energy consumption. Based on this it is conclusive that fill level measurement of ball mills is an important issue for grinding efficiency. This fill level information can be used for operators to control ball mills and also for engineers to run simulations and improve confidence levels of circuit designs (Shi, 2016)."

Jan 1, 2018

By Saeed Farrokhpay

It is known that the grinding condition has a major effect on the beneficiation characteristics of the minerals in subsequent processing, in particular, flotation. In the flotation process, particles surface and their condition can significantly influence collector adsorption and flotation performance. For example, particle shape and its surface roughness occurred during grinding may influence flotation characteristics of a specific ore. In fact, adsorption of different cationic and anionic species on mineral surfaces can be varied depending on the selected comminution procedure. The flotation performance of sulphide minerals can be detrimentally affected by the surface oxidation. The amount of surface oxidation may reduce the hydrophobicity of the mineral and makes adsorption of collectors less selective. Improved liberation may generally result in improved flotation recovery. However, this may result in finer grinding and slimes, and consequently, reduce the overall flotation recovery. This paper discusses the effect of wet and dry grinding on copper flotation of a complex Cu-Pb-Zn ore. Industrially, wet grinding is preferred due to its higher energy efficiency and owing to downstream processing requirements. In this study, series of flotation tests were conducted,and surface analysis (XPS and ToFSIMS) were performed after wet or dry grinding at two different P80 values. Mineralogical study was also conducted to investigate the liberation of valuable minerals after grinding. A higher copper flotation recovery was found for wet grinding. However, the copper recovery was increased by further grinding in both conditions (wet and dry). The results showed a higher collector adsorption on copper mineral surfaces after wet grinding. The surface analysis also revealed that the ore is slightly more oxidized after dry grinding probably due to higher temperature during dry grinding.

Sep 1, 2012

By T. C. Rao

This presentation identifies how mineral (coal included) processing profession should look at the challenges (threats) being faced by mineral industry. Presently, the focus is more on supply and demand on minerals. In addition, the R&D activities in the chain of mine-to-metal are paying more attention (if not only on) the processes being adopted, development of new equipments and modeling and simulation. But the profession is grossly ignoring aspects such as impact of the processes on other resources, of the ways we extract, use and dispose them socio-economically and efficiently. A business model which may encompass all these dimensions are essential for the sustainable development of mineral industry and a possible approach in this direction is presented. To start with, for the sustainable growth and existence, the profession must be aware of the prospective impacts of their activities on critical factors such as ? political (changing government policies), geographical (environment, land, water and habitat), which have major bearing on the survival and growth of the industry. Mineral Processing professionals have to join hands with mining engineers to answer some relevant questions related to the impact of mineral industry on society. Mining can become economically viable only if mineral processing engineers come out with innovative solutions to reduce capital and operating costs. The solutions have to be adoptable and practically feasible so that industry looks at us for directions. In fact, we have to move towards beneficiation of nano particles striving towards zero waste. Some of the gaps in the knowledge of procedures being followed in the design and operation of processing plants are highlighted. Enhancing the knowledge base for solving unexplored possibilities, solutions to evolve sustainable development measures which demands innovation both at academic and practicing levels is the need of the future. Well-structured academic programmes are to be formulated so that the graduates of these programmes can make an effort to look at processes/concepts with a new insight and approach; the profession should excite the young brains with challenges. R&D funding agencies have to have a long-term perspective on mineral processing so that closer interactions between academic institutes, industry and R&D organizations are sustainable and that innovations are at least a few years ahead of needs of future challenges. Keywords: sustainable growth

Sep 1, 2012

By N. Tsoni

The separation and recovery of fine and ultra-fine particles during the processing of mineral commodities by conventional separation methods is difficult and inefficient. This is due to the problems posed by the very small size of the mineral particles. The fine and ultra-fine mineral particles are either generated during size reduction processes or are necessitated by liberation size. This problem is expected to deteriorate, as deposits of even lower grade are processed. The inefficiency of the conventional separation methods with regards to the processing of very fine particles leads to the loss of considerable quantities of mineral commodities to the tailings. Novel methods and techniques as well combinations of known methods have been tested over the years. Among them, selective aggregation, along or in combination with flotation, has been given much attention. This study deals with the application of hydrophobic agglomeration as a separation method for very fine particles. The selected mineral system is magnesite/quartz, due to its sensitivity to physi-cochemical separation methods. The aim was the selective agglomeration of magnesite using sodium oleate. Tests on single minerals revealed that separation seems feasible and efficient. The parameters examined were: pH, quantity of sodium oleate, conditioning time, and, finally, settling time. Tests carried out on artificial mixtures of the two minerals, under various proportions, confirmed the results obtained from single mineral tests but they were slightly inferior. Finally, hydrophobic ag-glomeration tests were carried out on single and artificial mixtures of minerals using sodium oleate and petroleum as reagents. The results show that the addition of petroleum improves the results. In conclusion, hydrophobic agglomeration can be applied successfully even for fine particles of difficult-to-be-separated systems such as magnesite and quartz.

Jan 1, 2014

By Andrzej Wieniewski, Cezary Regula, Bozena Skorupska, Krystian Cichy

"In this paper, experiences from Polish non-ferrous metals ores enrichment plants in the copper and blende concentrates quality improvement are discussed. The blende concentrate being produced in ZGH Boleslaw S.A., with Zn content of about 54,5% is characterized by the relatively high magnesium content reaching a level of 1% resulting from the dolomite presence, while for the zinc production by electrowinning a concentrate in which magnesium content should not exceed 0,3% is required. The implemented new technology for the quality improvement of blende concentrate is based on the leaching of zinc concentrate with sulfuric acid aimed at dissolving of the contained dolomite, and then flotation of the leached concentrate. It allows to obtain a concentrate with magnesium content below 0,1% at the simultaneously increased zinc content to about 57,5%. In the paper, laboratory tests results on the development of optimal flotation flowsheet for the gypsum removal and the industrial tests results concerning the process optimization of this flotation are discussed. In turn, the copper concentrate being produced in Polish copper ore enrichment plants KGHM PM S.A., is characterized by the increased organic carbon content - above 8%. It creates problems with the smelting of this concentrate because of difficulties with the heat removal derived from the combustion of organic carbon in the flash smelting process. The implementation of segregating flotation to the industrial practice allows the effective production of two concentrates with the differentiated chemical compositions - a concentrate with increased copper content and reduced organic carbon content for the flash smelting process, and a concentrate with lower copper content and increased organic carbon content for the shaft smelting process. In the paper, conditions of the segregating flotation and the achieved results are described."

Jan 1, 2014

By P. Khattri

At Tata Steel, Coal is washed in gravity and froth flotation circuit at 13-15 mm size and below. Being coal is high in ash (~35%) and difficult washability characteristics (having high (~40 %) NGM at desired ash levels) needs more and timely quality data of ROM for effective optimization and process control. Conventional approach of supplying quality data takes 4-5 hours time. This means during this period, it is assumed that coal is having similar characteristics as of previous set and it is not possible to fine tune during this time which resulted in yield loss. Hence producing clean coal on agreed ash value consistently is a challenging task because of high NGM and variation in input quality. To overcome the problem of collection of representative sample and timely result a new technology was adopted Prompt Gamma Neutron Activation Analysis (PGNAA) technology which is basically an online analyser using Gamma rays as the source to measure the ash content in coal running on a conveyor which gives real time ash analysis. The details of this technological intervention are discussed in details in this paper. Keywords: near gravity material, PGNAA

Sep 1, 2012

By E. Gock

Based on the scientific investigations on mechanochemical synthesis of metal sulphides from metals or metal compounds and sulphur or sulphur compounds, the article describes the industrial production of nanoscale metal sulphides. Special operational conditions such as inert atmosphere, size and type of the grinding balls, grinding time and specific energy input are taken into consideration. A system configuration for the manufacturing of sulphides at a capacity of 100 kg/h is presented.

Jan 1, 2014