Search Documents

By D. G. Minnes

Many non-metallic minerals and structural materials are produced in Ontario to serve the needs of domestic manufacturers and export markets. In 1982 production was estimated to have a value of $765 million. Approximately 81 per cent of this was represented by structural materials, nearly 12.8 per cent by salt, and the remainder was other industrial minerals. Total mineral production in Ontario in 1982 was estimated at $3 .16 billion, down nearly $1.5 billion from 1980's high of $4.58 billion.

Jan 1, 1984

By Thomas C. Poulter

Abstract The Poulter seismic method of geophysical exploration is an attempt to obtain an increased efficiency in the conversion of the energy of an m~pl06ion into useful energy which has directive properties and which contains a minimum of random frequency and random phase relations. Very little effort has been made in the past to simplify OT even control the uniformity of the seismic energy being introduced into the ground. The Poulter seismic method is also an attempt to improve the signal-to-noise ratio not merely by trying to complete the impartial filtering done by the earth on ,the continuous spectrum of primarily high-frequency energy radiated from a shot point but by applying a frequency control at the point of origin of the seismic wave. The energy from a shot-hole charge is peaked in a frequency which is much higher than will be transmitted through the ground, and its absorption introduces background interference. Only 10 to 20 per cent of the seismic energy of a shot-hole charge .is directed downward in a 90-degree vertical cone, whereas, from a pattern of charges detonated above the surface of the ground, 85 per cent of the seismic energy is included in a 90-degree cone and in some cases it is even confined to as small as a 30-degree cone. This greatly reduces the horizontally distributed energy, thereby producing a marked improvement in the signal-to-noise ratio. The frequency of the signal energy may be peaked in a rather narrow range by the proper application of two or more impulses upon the surface of the ground controlled as to direction, magnitude, and timing. These impulses may be controlled by the reflection shock wave technique, the pressure pulse technique, and the sequence firing technique, using the primary controls as outlined. The information obtained from the study of directivity of seismic energy in a high velocity, uniform material such as the ice on Taku glacier, in the Juneau ice field in Alaska, has been of great assistance in the application of the method to oilfield and mining problems.

Jan 1, 1950

By W. de Klerk, M. B. Thorpe

Golden Star Resources Bogoso operates in Ghana’s Western Region. The gold recovery plant includes; a flotation circuit producing a concentrate for the BIOX® process that oxidizes sulphides before a CIL circuit; and a dedicated CIL circuit. BIOX® uses bacteria, therefore water from the BIOX® and CIL plants remained separated; CN water could not be introduced into the flotation / BIOX® circuit. The operation built a process water inventory with high TDS and installed a process water treatment plant (PWTP). Water was released in compliance the permits but containing some thiocyanate. The PWTP brine was returned to the TSF, further exacerbating the TDS. The operation experienced a drought removing the traditional water sources; the team evaluated the options to maintain production - various water streams were laboratory tested provided options for water use. The paper presents the story (treatment chemistry and process chemistry) of continued operations by treating stored water and PWTP discharge water with peroxide; brine usage within the CIL circuit, which increased gold recovery (laboratory testing) and reduced the TDS. Water flows were further modified to include hydraulic tailings re-mining to a CIL circuits. Details of the recovery, basic chemistry and costs savings are provided.

Jan 1, 2014

By G. Viramontes-Gamboa, A. Encinas-Oropesa, S. Velázquez-Roque, L. A. Ibarra-Bracamontes

Some industrially relevant applications for pyrite nano/micro-particles have been proposed in the literature, such as the catalysis of chalcopyrite leaching, the removal of As(III), As(V) and Cr(VI) from solution, as photovoltaic devices, and others. Even though pyrite can be recovered from solution by flotation, for some applications it may be beneficial to provide pyrite with magnetic properties. In this work, a methodology to synthesize magnetic shell/core composites made of pyrite as the shell and either natural or synthetic magnetite as the core is presented. The size of the magnetic composite may range from tenths to hundreds of microns. The synthesis is basically made by stoichiometrically mixing iron nano/micro-particles with sulfur microparticles with magnetite particles, and bringing the mixture in an oxygen free atmosphere from 200 to 300 °C for 4 h. The composites were characterized by optical microscopy, Scanning Electron Microscopy and X-Ray diffraction.

Jan 1, 2014

By M. S. Badollet

"The study of the physical properties of asbestos minerals requires a careful isolation of the fiber from the wall rock and, at a later stage, a comparison of these physical properties with those of fibers that have passed through the milling and beneficiation processes.The effects of mineral impurities, loss of fiber length and the formation of extreme fines (asbestic and/or associated minerals) often show up in the formation of special asbestos products as well as in the commercial production of asbestos papers, mill-boards, asbestos cement products, plastics and insulation materials, and in the filtration of blood plasma and wines.Numerous test methods have been developed in Canada and in England for use in the asbestos industry. Special treatments of asbestos fibers have been used to improve their physical and chemical properties and to eliminate impurities.Numerous problems connected with the use of asbestos fibers are discussed, such as the effects of asbestos on filtration, surface area, surface treatments using organic or inorganic materials, the surface charge on the fiber, the presence of magnetite and air pollution elimination. Biological studies on finely ground asbestos, when dispersed in 0.9 per cent sodium chloride solution and then sterilized and injected into hamsters, show that by reducing the dose, the tissue damage can be largely avoided. In these experiments, Arizona asbestos fibers were carefully extracted from the wall rock, finely ground, and examined chemically and micros-copically for any mineral impurities that might be present so that any effect on the hamsters would be directly due to the presence of the asbestos. The harsh Arizona fiber induced more extensive tissue response than the soft fiber when tested in hamsters."

Jan 1, 1969

By F. P. Hassani, Jacque Ouellet, M. Hossein

A laboratory investigation was undertaken to evaluate the effectiveness of different binding agents in a paste backfilling operation suitable to be used in a sulphide-rich environment. Different combinations of Portland cement and fly ash type C as well as ferrous slag were used as the binding agents. The unconfined compressive strength of the samples was measured for extended curing periods. The results indicate that the addition of 3% slag in the binding agent mix could produce strengths up to 0.5 MPa in the samples under investigation. For higher binding contents, the addition of Portland cement will lead to higher availability of calcium hydroxide and calcium aluminate, which are susceptible to deterioration from the phenomenon known as sulphate attack. Using slag, on the other hand, will reduce the permeability, availability of calcium hydroxide, and dilute the calcium aluminate ions reducing the susceptibility of the samples to sulphate attack. However, gypsum will form which could have the same detrimental effect on the strength of the treated matrix. Therefore, special attention must be given to the content and properties of agents used to activate the pozzolanic properties of the slag.

Jan 1, 2001

By B. R. Conard

Occupational epidemiology of the nickel-producing industry has found that inhalation exposures to certain nickel-containing substances are linked to respiratory cancers and to nonmalignant respiratory endpoints. Establishing such a linkage, however, is complicated by the fact that some diseases occur long after exposure to a causal agent (i.e., some diseases have long latencies). Furthermore, most chemical agents (especially nickel substances) vary significantly in their toxicological properties and their concentrations in workplace air have varied over processing history. Because of these complications, it is critical to understand historical exposures to specific nickel substances. To assist in this effort, the author focuses on the history of smelting and its related processes at Vale Canada’s (Inco’s) Ontario operations in the first half of the 20th century.

Jan 1, 2012

By P. O. Parfitt

The Critical Path Method has proved its usefulness at Mcintyre Porcupine Mines Ltd. This paper illustrates the techniques of network construction and analysis, and the application of the method at the Mcintyre copper mine to various projects in the gold mine. C.P.M.'s use in a mill maintenance project is also discussed.

Jan 1, 1966

By J. E. Rehder

IN A DISCUSSION of use of any material of ?construction in the mining industry, two points of view must 'be kept in mind - that of the producer or manufacturer of mining and metallurgical equipment, and that of the maintenance and operating staff of the mining plant. In the first case, the choice of material of construction is up to the manufacturer and the user of the equipment has little direct say in the matter. However, if materials are badly chosen and the equipment does not function properly, wears out rapidly, or costs too much, repeat orders ?will likely go to a different manufacturer, so that, in the end, the consumer or mine operator does have the final voice. In the case of materials for maintenance work and plant operations, however, .the mill personnel have direct control over purchases and it is then that a well-balanced knowledge of materials, their properties, and their costs, can be directly useful. With all materials of construction, the final criterion is unit cost versus service performance, so that the lowest possible total operational cost will be obtained. Sometimes this means using the cheapest material available, sometimes the most expensive, but in any case careful analysis of service performance, replacement cost, and material cost is essential to determining the material that produces lowest total cost.

Jan 1, 1956

By M. Dadvand, G. Kipuros, A. Dadvand

"The ability to codeposit fillers within a nickel matrix has led to the production of a new generation of cermet coatings with properties useful for various applications. Hexagonal boron nitride (hBN) is a ceramic-type particulate matter with thermal conductivity, thermal stability, inertness, and lubricity properties that allow it to be codeposited. In this paper, a method was developed for modifying hBN surfaces to allow them to be uniformly dispersed in water-based solutions such as an electroless nickel plating bath. hBN surface modification improved wear performance of the electroless plated cermet due to enhanced interaction between the particulate and nickel matrix. RÉSUMÉ La capacité à effectuer un dépôt simultané de charges dans une matrice nickel a abouti à la production d’une nouvelle génération de revêtements cermet (une combinaison de céramique et de métal) dotés de propriétés très utiles pour diverses applications. Le nitrure de bore hexagonal (h-BN) est une matière particulaire de type céramique utilisée pour ses excellentes conductivité et stabilité thermiques, son inertie ainsi que son caractère lubrifiant, qui permettent son dépôt simultané. Cet article explore une méthode mise au point pour modifier les surfaces du h-BN de manière à ce qu’elles se répandent uniformément dans des solutions aqueuses telles qu’un bain de dépôt autocatalytique de nickel. La modification des surfaces du h-BN a amélioré la résistance à l’usure du placage autocatalytique du cermet en raison d’une interaction accrue entre la matière particulaire et la matrice nickel.INTRODUCTION Electroless nickel alloy coatings can be used for many applications; however, the need for improved tribological properties such as higher wear resistance and better lubricity has increased interest in incorporating particulates (fillers) into the nickel matrix by codepositing the particulates with nickel during the plating process. The selection of the particulate type depends on the desired properties (Sahoo & Das, 2011; Sudagar, Lian, & Sha, 2013). In terms of tribological applications, electroless nickel-based composites are categorized mainly into lubricating and wear-resistant composite coatings depending on the type of particles incorporated. The electroless nickel-phosphorus (Ni-P) composite coatings are composed of codeposited solid lubricants such as polytetrafluoroethylene (PTFE), graphite, WS2, MoS2, and hexagonal boron nitride (hBN) and, compared to nanocomposite electroless Ni-P coatings, they demonstrate a lower coefficient of friction. On the other hand, the nickel-phosphorus wear-resistant composite coatings are composed of hard particles such as silicon carbide (SiC), aluminum oxide (Al2O3), boron carbide (B4C), silicon nitride (Si3N4), diamond, tungsten carbide (WC), and zirconium oxide (ZrO2) and, compared to nanocomposite electroless Ni-P coatings, they have higher hardness and better wear resistance (Sahoo & Das, 2011; Sudagar et al., 2013; Parucker, Klein, Binder, Ristow, & Binder, 2014; Chakarova, Georgieva, Petrova, Dobreva, & Stoychev, 2016)."

Jan 1, 2018

By P. E. Fox, R. S. Cameron

"The QR gold deposit lies in the Cariboo plateau region of central British Columbia. The deposit was discovered in 1977 and since then a mineable reserve of 1.3 million tonnes grading 4.7 g/t Au has' been outlined in three separate zones. Soil sampling of glacial tills followed by diamond drilling of favourable host rocks proved to be key exploration techniques.The deposit is situated in the southern Quesnel terrane along the eastern fringe of the Intermontane Belt which here comprises a sequence of basic and intermediate volcanics and a series of stocks of alkaline affinity; generally diorite, monzonite and syenite. Hornfels and epidote-rich ferromagnesian exoskarn and sulphide-rich mantos have developed in a metamorphic aureole formed around a central diorite stock. Gold-rich zones lie along the outer periphery of the aureole where bodies of gold-bearing epidote-rich skarn and auriferous mantos rich in epidote and pyrite have formed in beds of calcareous tuffite lying at the top of a thick basaltic sequence. The deposit is regarded as' a subclass of gold skarn deposits. Diagnostic features are its association with alkalic intrusive rocks in a subvolcanic setting and the presence of oxidized, epidote-rich mineral assemblages.IntroductionThe QR gold deposit lies within the Cariboo plateau region of central British Columbia, 58 km southeast of Quesnel. The deposit, owned by Kinross Gold, was discovered during a regional reconnaissance program by Dome Exploration (Canada) Limited and Newconex Canadian Exploration in 1977. Considerable exploration and development has been done since that time. Mineable reserves of 1.3 million tonnes grading 4.7 g/t Au have been outlined to date in three zones."

Jan 1, 1995

By J. M. Whatley

"IntroductionIN UNDERGROUND mining operations, the mine hoist has become one of the most important and one of the most expensive single pieces of equipment. As the means of transporting men and materials to the face, broken ore to the mill, and waste to the dump, it is often the very lifeline of a mine and must operate with dependability and efficiency or the whole operation will suffer. The mine hoist has become synonymous with safety. In few other types of mechanical equipment do so many men so frequently and completely place their lives. In Canada, more has probably been done to assure safe hoisting than in most other countries, but, unfortunately, this has resulted, in many cases, in the mines having to pay a high price for equipment. Hoist manufacturers have carried out much research in recent years in the endeavour to keep down these costs and at the same time maintain or improve the efficiency and safety of their products. Broadly classified, the bases for design research are dependability, efficiency, safety, and first cost.Probably the greatest single factor influencing the design of mine hoists was the introduction of electric motor drives. It was not until about 1905 that an effective start was made in the development of electric mine hoists, and then only with machines of small size. From that time on, however, progress was rapid, as may be gauged from the fact that by 1910 one large group of mines in Johannesburg had in use, or on order, fifty-four three-phase hoists and four Ward-Leonard. type hoists."

Jan 1, 1953

By Megan Becker, Aubrey Mainza, Indigo Research Laboratories, Jenny Wiese, Gaynor Yorath, Lucy Little

Particle shape characterisation has an important role to play in mineral processing, to clarify effects of shape on rheology, equipment wear rates, comminution, classification, sizing and flotation. However in industry, shape characterisation is not routine, and the most commonly used shape descriptor in the field (circularity/ angularity/ sphericity) is not invariant. This study aims to investigate shape measurements for a fine particulate ore sample measured with different analytical devices. Two Automated Scanning Electron Microscopy devices with Energy Dispersive X-ray Spectrometry (FEI QEMSCAN® and Zeiss Mineralogic®), and a camera based image-sizer using dynamic image analysis (Retsch CAMSIZER® XT) were compared. Each device was used to analyse the shape characteristics of specific particles in both a coarse sample (–212/+150 µm) and a fine sample (-53 µm) of UG2 platinum ore. Circularity and Roundness frequency distributions obtained from the three devices were then compared. For selected individual particles, circularity showed higher variability than roundness, and the sample circularity distributions obtained by the three devices were completely different. It is clear that circularity data from different studies relying on different devices should not be compared on an absolute scale. The shape parameter roundness was found to be a more robust descriptor than circularity, and it can give a stronger indication of a particulate sample’s shape characteristics on an absolute scale. However, there were still significant differences in the roundness measurements obtained by the CAMSIZER XT and the two Auto-SEM devices, which was attributed to the dissimilar mechanisms of image capture.

Jan 1, 2016

By T. H. Chuang, Y. Y. Shiue

"Rapid whisker growth was significantly alleviated in a Sn-58Bi alloy doped with 0.5 wt.% La. Experimental results showed that many thin, plate-form intermetallic phases appeared in the solder matrix. The absence of tin whiskers was correlated to the shape effect of RE-containing intermetallic plates. After reflowing, Cu6Sn5 intermetallic compounds appeared at the solder/pad interfaces of Sn-58Bi and Sn-58Bi- 0.5La packages with OSP pads, which grow linearly during the aging at 75 and 100? for various times ranging from 100 to 1000 h. In addition, the interfacial intermetallics layers in Sn-58Bi-0.5La solder joints were also observed thinner than those in undoped Sn-58Bi joints. However, RE-containing interfacial intermetallic compounds in Sn-58Bi-0.5La solder joints led to lower bonding strengths in both ball shear tests (0.4 mm/s) and high speed ball shear tests (2000 mm/s). All the reflowed and aged solder joints of both packages were ruptured through the solder balls indicating brittle characteristic INTRODUCTIONIt has been widely reported that solder alloys doped with rare earth (RE) elements reveal many beneficial effects, such as higher strength, lower melting point, improved wettability, and longer creep life (Wu et al., 2004; Ma et al., 2002; Chen et al., 2002). In addition, Dudek et al. reported that the alloying with 0.5 wt.% La in Sn-3.8Ag-0.7Cu solders resulted in an increase of rupture strain, up to 150% over undoped solders (Dudek et al., 2006). However, Chuang and Yen observed that a large amount of long, fiber-shaped tin whiskers were extruded out of the oxidized CeSn3 intermetallic clusters in the matrix of a Sn-3Ag-0.5Cu-0.5Ce solder air-stored at room temperature for several days (Chuang & Yen, 2006). Furthermore, many coarse hillocks appeared around the CeSn3 clusters in the RE-doped alloy after storage in an air furnace at 150? for several minutes. Chuang proposed a mechanism for the phenomenon of rapid whisker growth, which the predominate oxidation of CeSn3 intermetallics in Sn-3Ag-0.5Cu-0.5Ce solders induced compressive stress and extruded the tin atoms out of the specimen in the form of tin whiskers (Chuang, 2007). However, further investigation showed that Sn-9Zn-0.5Ce solders, after long term exposure at room temperature and 150?, were immune to the whisker growth; the immunity was attributed to the refining of the CeSn3 intermetallic phase in the alloy (Chuang & Lin, 2008). The inhibition of tin whiskers through the refining of rare earth containing intermetallics was further observed in Sn-3Ag- 0.5Cu-0.5Ce solders doped with 0.5 wt. Zn (Chuang & Lin, 2009). In addition to the size effect, the thin plate shape of intermetallic compounds was also shown in this study to inhibit the whisker growth on the surface of Sn-58Bi-0.5La solders."

Jan 1, 2012

By R. Yost

"This paper describes a case study that illustrates how detailed geological engineering results were communicated to address a range of stability challenges in a producing mining environment. Instead of using standard geological engineering terminology, findings and recommendations were communicated as mine design options and mining responses to accommodate possible slope instabilities and associated risk. The resulting medium- to long-range mine plan integrated the potential slope instabilities and associated mining responses to provide a higher probability of planned resource extraction. It also reduced the potential for long-lasting production and processing delays.RÉSUMÉ Cet article décrit une étude de cas illustrant l’intérêt de la communication de résultats détaillés de géologie appliquée pour résoudre un éventail de difficultés relatives à la stabilité dans un environnement minier en production. Plutôt que d’utiliser une terminologie classique de géologie appliquée, les résultats et les recommandations ont été communiqués sous forme d’options pour la conception d’une mine et de réponses dans le contexte minier permettant de surmonter les éventuelles instabilités des pentes et les risques associés. Le plan de mine sur le moyen à long terme qui a résulté intégrait les instabilités potentielles des pentes ainsi que les réponses connexes dans le contexte minier afin de renforcer la probabilité de l’extraction des ressources prévue. Il réduisait également la possibilité de retards durables dans la production et le traitement.INTRODUCTIONSlope failures in an active mining operation are unscheduled but expected events, in the sense that the geotechnical design often assumes the potential for slope failure but cannot predict exactly when a failure will occur. Unfortunately, the geotechnical engineering cycle—characterization, slope design, displacement monitoring, instability management, and failure remediation—that is necessary to manage slope-failure risk is not always well known or understood outside the geotechnical engineering profession. The first introduction many personnel have to geotechnical engineering is when a slope failure starts to develop and appears to threaten the safety and livelihood of their workplace.At that point, the task of communicating the risk management of slope failure falls to the geotechnical engineer, who must summarize analytical methodology, design concepts, monitoring trends, and analysis results, frequently to an audience with limited exposure to the geotechnical field. All too often, the response has been to present a risk-management plan in the vernacular of geological engineering— using terms such as factor of safety (FOS), pore-pressure reduction, and slope unloading—instead of expressing the problem and solution in more readily understood mine production terms."

Jan 1, 2017

By Derrick Hunter, Pat Feighan, Keith Chrystall, David Wells

"Equipment which may be remotely operated, has some degree of on-board intelligence, and which for periods of time may operate autonomously, is referred to as telerobotic. Recent advances in electronics, computers and hydraulic equipment have dramatically reduced the cost and simplified the process of converting standard industrial equipment to telerobotic control. The benefits of telerobotic equipment include improved safety by removing the operator from dangerous situations, reduced maintenance costs and increased productivity. This technology has been proven in various military, nuclear, and police applications.The surface mining industry has expressed an interest in automation and is characterized by a willingness to use remotely operated equipment, however, the majority of telerobotic equipment currently in use is experimental or prototypical. Potential applications of telerobotic equipment for surface mining include remote operation of equipment near dangerous high walls and other unsafe areas, utilization of robotic trucks for routine hauling operations, and control of jointed equipment. In addition, component technologies of telerobotic systems are relevant to various forms of condition monitoring, operator feedback systems, and vehicle positioning.Attention must now be directed toward resolving more complex problems associated with enhancing feedback to the operator, improving the man/machine interface, and ultimately, improving efficiency. Removal of the human operator from the work site introduces significant complications in replacing the sensory inputs that an operator normally uses to efficiently run his machinery. These can be difficult to define and even more difficult to replicate remotely and may include restrictions pertaining to vision, hearing, and touch.In cooperation with Defence Research Establishment Suffield and the Alberta Research Council, Robotech Industries Ltd. is pursuing the development of additional technologies to further enhance an operator’s ability to control remote telerobotic equipment. These developments include a head-mounted display, additional control station displays and improvements to coordinated motion control software. Prototypes of these developments are expected to be completed and tested by the fourth quarter of 1997."

Jan 1, 1996

By David S. Robertson, Richard F. Douglas

"Uranium is a lithophile element of relatively low natural abundance. Concentrations of uranium form through processes of erosion and sedimentation, and over 90 per cent of the western world's uranium ore reserves are in sedimentary rocks.Proterozoic quartz-pebble conglomerates contain about 60 per cent of the known uranium reserves. These are all similar in appearance, in mode of distribution and in manner of origin. They carry uranium minerals and/or gold and abundant pyrite. Their unique distribution in Huronian time required a pre-existing crust well enough evolved to have plentiful quartz and abundant gold, uranium and pyrite. The materials of value were deposited as detrital heavy minerals prior to the appearance of an oxidizing atmosphere in late Proterozoic time.Epigenetic uranium deposits occur in arkosic sedimentary rocks through the entire geological column. About 30 per cent of the western world's known ore reserves are in _these rocks. This type of deposit is particularly prominent in semi-arid parts of the United States, having yielded most of the uranium ore produced and containing nearly all of the known reserves.The Western States type"" of deposits occur in lenticular, permeable stream-laid sedimentary rocks. The de-posits are believed to have been precipitated from moving ground water at locations where plant debris or other organic matter had accumulated. The uranium may be derived from volcanic sediments, which are commonly associated with the units containing the ore, or it may be leached from exposed granite surfaces or from granitic debris which forms the sediments.A significant part of the world's uranium resources are in black shales and lignitic rocks. The lignites that contain uranium are virtually valueless as potential sources of heat. Uranium concentrations at levels such as to be potential sources of by-product uranium occur in many phosphorites.Reworked sediments may provide uranium in pegmatites and vein-like deposits."

Jan 1, 1970

By D. A. Sloan

"THE FIRST COMMENTATOR that I will call on is Mr. W. G. (Bill) Brissenden, Vice-President, Mines, Noranda Mines Ltd. Bill, would you care to comment.W. G. BRISSENDEN ...Mr. Chairman, Ladies and Gentlemen, I spent some time reading the four papers that were presented here, yesterday evening, and decided that the four to six minutes that I had been allotted for this afternoon were going to be pretty tough to meet. It's a very big subject and I just hope that I will be able to stay within my time limit. As has been so aptly demonstrated by the members of our panel here this afternoon young men in growing numbers continue to be attracted to careers in the mineral industry, especially to careers in mining engineering. Now from 80 the point of view that the profession may have regained its status this is indeed welcome news. However, perhaps all of the members seem to have the suspicion that the number of mining engineers that the industry can absorb is a much lower figure than previously forecast. It is said that technical school graduates are now occupying some of the jobs once considered the private preserve of the mining engineer and also that mining engineering undergraduates are having trouble locating summer employment. If these interpretations of mine are correct then we are now confronted not only with our old dilemma - whither the mining engineer - but also with an urgent need to solve it. We cannot allow our profession to become once again an undesirable one in the eyes of our youth because if we permit such a thing to happen a second time the profession may never recover."

Jan 1, 1972

By R. J. Chase, C. Davies

"Abstract- The Merelani graphite-tanzanite deposit is located in northeast Tanzania, 14 kilometers south of Kilirnajaro International Airport and in close proximity to the towns of Moshi and Arusha . The graphite mineralization is hosted by relatively undeformed linear Proterowic metasedimentary gneisses, several of which have been subjected to hydrothermal alteration resulting in tanzanite mineralization. Exploration work comprised detailed geological mapping coupled with pit and trench channel sampling and a subsequent 1500 meters of diamond drilling. In addition, metallurgical tests have shown the graphite to be of unusually coarse flake size, crystallinity and high purity.Feasibility studies have shown the economic viability of a major coarse flake graphite deposit with the measured resource to 50 meters in excess of 9 million tonnes assaying over 8o/o graphitic carbon . Production is due to start by the end of the first quarter of 1994 with the processing plant design capacity initially set at 15 000 tonnes per annum.ln addition to graphite production, tanzanite will be produced through selective mining within the graphite open pit in the upper horizon and from underground workings within the lower horizon.The Merelani graphite-tanzanite deposit will be the first major orebody to be exploited through means of private funding since Tanzania gained independence."

Jan 1, 1994

By D. Moronkeji, R. Maharidge, D. A. Curry, B. J. Davis, U. Prasad, J. Franquet

"Proper shale characterization is crucial in shale gas drilling, exploration, completion and production. Unlike porous sandstone and carbonate reservoirs, the challenge with shales comes from their micro- to nano-darcy permeability ranges and the anisotropy of their mechanical and hydraulic properties. Most porosity-dependent logs are not sensitive enough to capture the true behavior of shales. Consequently, mineralogy and other strength and stiffness-related properties must be determined to characterize magnitudes and variances in shale mechanical and flow properties. In addition, these properties must pass quality assurance/quality control (QA/QC) practices to give confidence in their use in subsequent log calibrations, during geomechanical modeling, or in fracture design models. This paper presents a technique to integrate shale properties that are measured by various methods, and a methodology to perform QA/QC on the data before application.Shale properties originate from various sources, including downhole and laboratory measurements. Physical samples for laboratory testing are usually limited to a few depths. Lab tests are often costly, and replicating in-situ conditions can be difficult or impossible. In addition, results frequently show wide scatter, reflecting inherent depth variability and lateral heterogeneity. Wireline logs provide nearcontinuous data, but rarely yield direct measurements of rock strength properties. Although geomechanical and fracture models use log data, calibrating it with reliable and previously verified lab-measured properties is important. This paper presents a process to perform QA/QC on lab-measured data using various crossplots.Ten mechanical, microstructural and physical properties are graphically displayed to visually characterize shale strength behavior in ambient and in-situ conditions, whether measured or modeled statically or dynamically. These properties are often sourced from different departments. The properties are integrated but are individually subject to the previously mentioned uncertainties. Pairs of property values are crossplotted and compared with correlations from the literature or previously established with qualified data from related formations. Conformance with these correlations gives confidence in the data, whereas outliers are flagged as questionable. Repeating the process with questionable data crossplotted against other parameters for the same depth highlights the property with the greatest uncertainty. The determination of its value is investigated to locate the source of the inconsistency and establish a more reliable value. Where this is not possible, the user has a rational basis for rejecting that property value."

Jan 1, 2015