Search Documents

By Timothy Flaherty

We observed the boiling in the water very close to the water adjacent to where we were drilling. That only happened at the very beginning before it was switched to water flushing. Yes, it was performed with water flush.

Feb 10, 2003

By Bill Paparis

The thirty year old wharf structures at the Port Authority of New York & New Jersey?s Port Elizabeth Marine Terminal are being modernized for the next generation of Post-Panamax container ships, which require deeper water and larger container cranes. The terminal operator is upgrading the wharf in order to remain competitive, now and into the future. The upgrade coincides with the Army Corps of Engineers? $733 million project to deepen the main shipping channel in New York Harbor. This paper focuses on the structural modifications to accommodate berth deepening and to support the heavier loads of the new cranes. An overview is provided of the design and actual construction, including typical problems encountered when combining new and existing structures. The wharf improvements included: ? Installation of a steel king pile/sheet pile cutoff wall along the face of the wharf to permit increasing the depth from ?12.2 m + 0.61 m to ?15.2 m + 0.61 m ( ?40 ft + 2 ft to ?50 ft + 2 ft) ? Removal of the existing crane rail support beams and installation of new piles and beams to support the increased crane loads ? Replacement of the existing timber fender system with a new system capable of resisting the berthing energy of a 152,000 MT displacement vessel, and having dedicated sections for berthing barges ? Replacing the existing overhead, landside crane electric feeder system with a waterside, cable reel trench system. The work included upgrading the transformer capacity at the terminal for increased crane power demands This paper provides a case history for port administrators, terminal operators, engineers, and shipping lines challenged with upgrading aging terminals.

Jan 1, 2013

By Raymond Henn

Yes we have also used some however, again because of the nature of the maintenance window where we have that two hour (at best) window every night and due to the numerous other crews that are wanting to get in to do the other types of maintenance activities, we don't know if we are going to be getting into that same area from one night to the next. So even with the dormancy additives that one can add to cementitious grouts (that are good up to 72 hours) we don't know if we are going to get back in to the same locations from one week to the next. That's why I use the term "the forgiving nature of the acrylamide". It allows us to ream out the hole allowing us to use the exact same hole without having to re-drill a new hole. The program started in 1997 and we have a budget between labor/materials and equipment of 4.5 million dollars on a year to year basis. For the next few years that is going to come down drastically because the program is going to be more of an ongoing maintenance program. The program started in 1997 and we have a budget between labor/materials and equipment of 4.5 million dollars on a year to year basis. For the next few years that is going to come down drastically because the program is going to be more of an ongoing maintenance program. Up to the end of 2001 we were just over 1.7 million liters of between AV100 and AV118 grout. Of that, approximately just under 200,000 was AV100 and the remaining balance was AV118.

Feb 10, 2003

By Dario Libano, Armando Caputo, Francisco Caputo

"UHE Peixe Angical is a 452 MW hydroelectric power plant located on the Tocantins River in Tocantins, Brazil. In 1999, geologists began feasibility studies to estimate the river’s hydroelectric potential, and the decision was made to proceed with the construction of a power plant. In 2002, after extensive investigation, the studies indicated geological homogeneity at the site for the dam, except for an anomaly detected on the left margin, and construction began on the $1.2 billion project.As the work began, the complex ground conditions presented several serious difficulties. The solution was unlike any undertaken before in Brazil— a 100-m-long secant cutoff wall, with 76 1.8-m-diameter piles of up to 78 m deep. All were placed in a six-month period.In the preparation for the detailed construction plans, further studies in the area of the anomaly better defined the geology so that a treatment program could be developed. The feasibility study had detected silicified rock with high permeability in one area, and an injection curtain was designed with five injection lines. In the other area with an anomaly, further investigation revealed a permeable marble formation that was 50 m thick. Here, a specific injection program with three injection lines was developed.The injections started in February 2005 in the marble formation area. By July of that year, only the primary and secondary holes were drilled from the three lines, resulting in a space between injections of 1.50 m. By the end of July, the drilling was halted. The contractor had identified a thick area of heterogeneous material below the transition zone that was characterized by a mixture of soil, fractured rock and hard fractured rock. The anomalies were detected while drilling, and both the general contractor and the designer concluded that the phenomenon of “piping” was taking place.Constructing a positive cutoff wall became a priority."

Jan 1, 2009

By Franz-Werner Gerressen, Manfred Schoepf

"Diaphragm walls are known as underground structural elements commonly used as retention systems for excavation pits and shafts and permanent foundation walls or elements. It can be anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm walling in even more complex conditions. Complex and/or challenging conditions in terms of ground conditions have a major impact in regards of choosing the right tools for excavation purpose. Complex conditions in terms of space limitations, especially for inner city job sites, require specifically adapted solutions for slurry, spoil, reinforcement and concrete handling and the related logistic to ensure smooth production. Furthermore, one focus will be given to the QA/QC topics of the production process. Real time installation control, data transfer and reporting systems become more and more important ensuring the five dimensions of a jobsite. Therefore, the paper will describe the construction method and the sequence of activities required for the construction of diaphragm wall systems with the focus on the cutter technology. It will describe also the main equipment which will be needed to execute these works under the various conditions INTRODUCTION Diaphragm walls are known as underground structural elements commonly used as retention systems for excavation pits and shafts and permanent foundation walls or elements. It can be anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm wall usage in even more difficult conditions. Of course diaphragm wall can also be used as deep groundwater barriers (Cut-Off-Walls). This market has shown that the demand for these types of walls is reaching more and more difficult soil conditions or required depths which are surpassing the current standard. The trench cutter is the most important tool for performing this work. The trench cutter itself is a reverse circulation excavation tool. It consists of a heavy steel frame with two drive gears attached to its bottom end, which rotates in opposite direction around horizontal axis. Cutter wheels are mounted onto the drive gears. As they rotate, the soil beneath the cutter is continuously being broken up, removed, mixed with the bentonite slurry in the trench and moved towards the opening of the pump suction box. The slurry loaded with soil and rock particles is pumped by a centrifugal pump which is located right above the cutter wheels, up through a hose system up to a desanding plant where the slurry is cleaned and returned into the trench."

Jan 1, 2015

"This model specification includes sample text shown in normal font with commentary in italics. The commentary is intended to highlight project-specific items the specification writer should consider during development of the specification. In some sections, typical values are presented to indicate common practice, and these values may be changed to reflect project-specific requirements. The commentary should be removed before using the specification for a project. 1. SCOPE The work consists of designing, furnishing, installing, and testing helical piles used to support foundation loads (compression, tension and lateral), and any ancillary materials (e.g., load transfer devices, etc.) according to the project plans provided and these specifications. Unless otherwise noted, the installing contractor shall provide all labor, tools, equipment and materials necessary to install the required piles. The parties referred to in this specification are as follows: • The Owner is the property owner. • The Owner’s representative is the individual or firm hired by the Owner to design and oversee the overall project. • The pile designer is the individual or firm generally hired by the installing contractor to design the helical piles. • Installing contractor installs and tests (if necessary) the helical piles, and possibly tasks associated with the project. It is important to clearly define the roles and responsibilities of every party on each project to promote good communication and reduce potential for contractual misunderstandings. Different types of contractual vehicles (design-build, value engineering, etc.) require different roles and responsibilities for the various parties, which should be considered in specification development. The Owner will provide suitable access to the construction site for the installing contractor’s personnel and equipment. Unless specifically noted otherwise in the contract documents, the Owner will remove and replace any structures, utilities, pavements, landscaping or other surficial improvements in the work area as necessary to facilitate the work. The Owner will be responsible for overall construction oversight to minimize potential for developing unsafe conditions. The work may include post-construction monitoring of pile performance if required by the Owner or the pile designer to confirm performance of the piles subsequent to their installation. The work may also include installation of additional piles if the initial installation does not meet specified capacity or performance requirements. Responsibility for providing subsurface investigation shall be addressed in the bid documents. The Owner is responsible for providing to the installing contractor all available subsurface soils, rock and groundwater information and geotechnical testing data."

Jan 1, 2015

4.5.1 General The provisions of the article shall apply to the design of axially and laterally loaded driven piles in soil or extending through soil to rock. 4.5.1.1 APPLICATION (Revised Article 4.3.1.1) Piling may be considered when footings cannot be founded on rock, or on granular or stiff cohesive soils within a reasonable depth. At loca-tions where soil conditions would normally permit the use of spread footings but the potential for scour exists, piles may be used as a protection against scour. Piles may also be used where an unacceptable amount of settlement of spread footings may occur. 4.5.1.2 MATERIALS Piles may be structural steel sections, steel pipe, precast concrete, cast-in-place concrete, prestressed concrete, timber, or a combination of materials. In every case, materials shall be supplied in accordance with the provisions of this Article.

Jan 1, 1989

By Ronald E. Walkington

The U.S. Department of Energy (DOE) is building the world's newest accelerator-based, pulsed-neutron system, called Spallation Neutron Source (SNS). The facility, located in Oak Ridge, Tennessee, is a partnership of six DOE national laboratories - Argonne, Brookhaven, Jefferson, Lawrence Berkeley, Los Alamos, and Oak Ridge. Oak Ridge has the responsibility for managing the partnership and ultimately operating SNS. SNS will provide opportunities for up to 2,000 researchers each year from universities, national laboratories and industry from around the world for basic and applied research and technology development in the fields of materials science, magnetic materials, polymers and complex fluids, chemistry and biology. When completed, this state-of-the-art research facility will provide neutron beams that are 12 times more intense than any other such source in the world. Most of the world's neutron sources were built decades ago. Therefore, it is easy to understand how SNS will provide new research opportunities unavailable elsewhere, and at the same time restore United States leadership in neutron sciences. Neutron scattering research provides valuable information about materials that cannot be obtained through microscopy, X-rays, spectroscopes, or other techniques. The information gained from neutron scattering research leads to improved materials that are used in high-temperature superconductors, powerful lightweight magnets, aluminum bridge decks, jet aircraft, compact and computer discs, magnetic recording tapes, shatter-proof windshields, and many other applications. SNS is like a flashing strobe light providing high-speed illumination of an object and will record the structure of physical and biological materials from plastics to proteins. Because neutrons have no charge, they can penetrate more deeply into materials than do X-rays, light, or electrons and thus reveal bulk structure and properties of materials. SNS will help to understand and "engineer" better materials and the manufacture of better products at the atomic level. Our high-technology society demands new materials that are stronger, lighter, and cheaper yet perform well under severe conditions. SNS, which is designed with the future in mind, will be the leading neutron research facility for many years to come.

Jan 1, 2001

By Olgun

Energy piles are a new innovative renewable energy technology to access and exploit the relative constant temperature of the ground for efficient heating and cooling of buildings. Examples of energy piles include drilled shafts, continuous flight auger (CFA) piles, driven piles, and micropiles. A field test setup was installed at the Virginia Tech Geotechnical Research Facility to study energy piles. The field test consists of a total of five micropiles 25 cm (10 inches) in diameter, four of which were equipped with circulation loops. The test piles extend to a depth of 30.5 meters (100 feet) and are heavily instrumented with strain gauges and temperature sensors. Several observation boreholes were formed around the test piles to monitor ground temperatures. Thermal conductivity tests and field load testing were performed to investigate the behavior of Energy Piles. This paper presents results of the thermal conductivity tests and thermo-mechanical field load test performed as part of this field investigation.

By M. Hesham El Naggar, Maged A. Abdlrahem

"Hollow bar micropiles have constructional advantages such as: fast and low-noise and low vibration installation process and small installation equipment, which allow access to tight places. In addition, they have efficient load transfer mechanism, which facilitates carrying considerable load in compression and tension. The common practice is to use diameter ratio of drill bit/ hollow bar (Db/Dh) around 2 in their construction, and they are typically designed assuming type B as classified by the Federal Highway Administration (FHWA). In this paper, the performance and capacity of Hollow bar micropile with different (Db/Dh) ratios are investigated. Full-scale micropiles were installed at a site in Ontario, Canada, and were tested in order to evaluate the uplift performance of Hollow bar micropile with different(Db/Dh) ratios. Two micropiles with two different ratios 2.25 and 3 were constructed and tested. The total length of the micropiles was 6m with embedded length of 5.75m. The soil at the site was primarily medium dense to dense sand. The results of the load tests are presented and discussed. It was found that the uplift capacity of the micropile increased by about 19.5% as Db/Dh increased from 2.25 to 3.INTRODUCTIONMicropile is a small diameter, less than 300 mm, drilled and grouted pile and is typically reinforced according to Federal Highway Administration (FHWA, 2005). The technology of micropile was introduced in North America in 1970’s, but the growth in the east coast of United State was intense compared to all other cities around the globe (Bruce and Nicholson, 1989). Nowadays, micropile construction is used extensively worldwide as a viable solution that offers several advantages such as fast installation in low headroom, minimal disturbance to the adjacent structure efficient load transfer due to high grout to ground bond strength. As the method of grouting has major influence on the grout – ground bond strength, FHWA has classified the micropiles into four categories. Type A: the grout is placed under gravity and no pressure is required. Type B: The grout is typically pressurized under a pressure range from 0.5 to 1 MPa as the temporary casing is withdrawn. Type C: the grout is placed in two-step process. First, the grout is poured under gravity only as in Type A. Before the hardening of the grout, similar grout is pressured of at least 1MPa without the use of packer. Type D: Like Type C, it is a two – step process, the grout is placed under gravity as in Type A and sometimes pressurized as in Type B. After hardening of the initial grout, additional grout is pressurized between 2 to 9 MPa through sleeved pipe by using packers, as many times as needed. According to this classification, hollow bar micropile is usually designated as Type B. However, the construction technique is completely different from Type B. Recently; there is a trend to supplement the four types of micropiles by Type E as represent to hollow bar micropile (Timothy et al, 2012). The construction method of hollow bar micropile involves two main stages which can be performed in one–step process: advancing the drilling bit attached to a threaded hollow bar to the required depth; and pressurizing the grout through nozzles of the drill bit."

Jan 1, 2016

By Silas C. Nichols

FHWA Interest is due to: ? An increase in successful projects in the U.S. private sector and in other countries ? Cost effective and more efficient in many circumstances ? Agency Priorities - FHWA "Vital Few" AASHTO TIG

Jan 1, 2005

By George Filz, Peter R. Cali

"Unnecessarily restrictive specifications could be limiting the cost effectiveness of deep mixing (DM) applications and therefore limiting use of DM on projects where there are other options. Excessively restrictive standards demanded for strength and permeability certainly increase contractors’ bid prices, and costing the owners and, in the case of Government projects, the taxpayers more than necessary. Yet, lax or ineffective specifications often exist for some vital components of the quality assurance and quality control. In this paper, specifications for key elements of DM design and construction are examined. Recommendations are made to improve and streamline DM specifications to better serve the common objective of constructing a safe and cost effective ground improvement project.INTRODUCTIONSpecifications should, at their best, convey the project design requirements and provide clear direction to the contractor regarding requirements for submittals, materials, execution, measurement, schedule, and other aspects as necessary. The specifications should not be overly conservative, restrictive or ambiguous, and they absolutely should not be deficient in measurement of quality. Guide specifications or recycled sections from previous projects often form the template for new project specifications. But standards that appear in guide specifications or from former successful construction should be critically scrutinized by the designer for relevance before using the copy/paste functions of the specifications writer’s keyboard. Because work does not always go as smoothly as planned, specifications for remediation of non-compliant construction should be clearly stated and enforced. Often, non-compliancy is reviewed after-the-fact and deemed to have met the design intent, indicating that either the specifications were too restrictive or the enforcement too weak.The Federal Highway Administration Design Manual: Deep Mixing for Embankment and Foundation Support, October 2013, was written by a panel of DM expert design practitioners and contractors. Guide specifications are included as Appendix C of the FHWA manual. Those guide specifications have been updated in the deep mixing section of the www.GeoTechTools.org website, and the updated specifications represent the most complete and authoritative compilation published to date. Although the specifications for DM at www.GeoTechTools.org are current and complete, and they portray the state-ofthe- practice, they too must be modified to fit specific DM applications, project needs, and site conditions. The keys to a good set of specifications are to prescribe construction only to the level that is required to meet the design intent, to require appropriate quality control and quality assurance (QC/ QA) activities, and to clearly address remedial measures required for non-compliant work."

Jan 1, 2015

By Karen Dawson

Pressure-grouted helical piles support a new seven-story homeless housing center in the Coney Island neighborhood of Brooklyn, New York. The project team instrumented and statically load tested piles to as much as 1,000 kips (4.4 MN) in advance of construction to obtain the approval of the New York City Building Code officials and to verify the design. Use of pressure-grouted helical piles required additional design effort and time risk because of New York City's Construction Code Determination (CCD1) process, which is required for non- standard deep foundation types. Despite

May 1, 2022

By C. Guney Olgun, Charles Elks, Sherif L. Abdelaziz, James R. Martin, Christopher Fox, Pier Luigi Iovino, Fatih Catalbas, Pierre Gouvin

"Energy piles are a new innovative renewable energy technology to access and exploit the relative constant temperature of the ground for efficient heating and cooling of buildings. Examples of energy piles include drilled shafts, continuous flight auger (CFA) piles, driven piles, and micropiles. A field test setup was installed at the Virginia Tech Geotechnical Research Facility to study energy piles. The field test consists of a total of five micropiles 25 cm (10 inches) in diameter, four of which were equipped with circulation loops. The test piles extend to a depth of 30.5 meters (100 feet) and are heavily instrumented with strain gauges and temperature sensors. Several observation boreholes were formed around the test piles to monitor ground temperatures. Thermal conductivity tests and field load testing were performed to investigate the behavior of Energy Piles. This paper presents results of the thermal conductivity tests and thermo-mechanical field load test performed as part of this field investigation.IntroductionThere is a developing trend around the world to explore alternative energy sources. The main driving forces are growing global energy demand, depleting natural resources and the adverse effects of greenhouse gas emissions from fossil fuel consumption. Geothermal energy is one of the promising renewable sources that can be utilized to offset such trends. However the use of geothermal energy has been limited mainly to certain hot spot areas where it is used either for district heating and/or electricity generation. Ground temperatures below a depth of about 6 meters (20 feet) remain stable compared to outside air temperatures, typically lying between 8-23°C (46-73°F) at most U.S. regions. The constant temperature and heat storage capacity of near surface soils in any region represent a tremendous potential of stored energy that can be used for heating and cooling of structures."

Jan 1, 2017

By P. K. Ray, Sudip Kumar Koley, Sainath M. Reddy, Devulapalli L. S Rasagna

Bangalore Metro Rail Project- phase II is one of the technological challenging project, particularly construction of underground metro rail system. The Bengaluru city is very congested area and connecting metro rail system with existing transportation networks is equally challenging. In this phase-II, the Underground metro is being constructed by blasting hard rock formation and supporting the shear zone. Most of the subsurface rock formations comprise of granitic Gneissic formations are of Precambrian age and shear zones that includes friable a thin weathered rock formation. With such subsurface geological conditions, , the anticipated construction challenges include : A) deep excavation of hard rock mass under old and sensitive structures and buildings, by controlled blasting; B) variation in the rock grade from grade I to grade V; C) weak rock mass at shear zone resulted in planar failure beneath the retaining wall; D) water seepage along shear planes; E) selection of a suitable method to conducted blasting near high voltage electrical machinery or power cables. This paper describes the methods adopted to mitigate these technological challenges and to meet stringent environmental compliances. These includes study and application of various geological, geotechnical parameters to develop a proper line drilling and controlled blasting techniques to minimize the ground vibrations and controlling the rock fragmentation and to optimize the equipment performance in terms of productivity and time schedules. The “Phase 2” software of “Rocscience” has been used and Regression analysis has been carried out by using MCD (Maximum Charge per Delay) and PPV (Peak Particle Velocity) to estimate with FOS (Factor of safety) for sensitive places such as nearby high rise buildings and electrical transformers.re.

Sep 1, 2022

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Numerical lateral load analysis based on the beam on Winkler foundation (BNWF) model (i.e., the p-y method) is a simple, and widely used tool to predict lateral responses of drilled shafts from field load tests. The lack of a site-specific p-y model for cemented soil layers such as caliche is one of the major limitations of simulating lateral load tests conducted in Las Vegas Valley. In this study, some of the existing p-y models for rock materials, such as Florida Limestone and Vuggy Limestone have been evaluated to simulate the lateral resistance of caliche. This has been done in the context of four lateral load tests in caliche-dominant sites from the recently constructed Raiders Stadium project in Las Vegas (NV). The uncertainty in characterizing the material properties of caliche has been addressed. The p-y analyses were performed using NVShaft, a MATLAB-based, comprehensive load analysis program. The applicability of the considered p-y models for caliche material was evaluated by quantifying the normalized error margins between measured and predicted lateral responses from the simulations of the mentioned load tests. Correlations between such errors and the depth and thickness of caliche in soil layers affecting numerical predictions were established, for both up to and beyond design load levels.

Oct 1, 2022

By Lawrence F. Johnsen

Six case histories are presented in which tall, slender high rises are supported on high capacity minicaissons. The recent development of a high strength rebar cage has resulted in compressive loads of up to 3400 kips on 24 inch diameter minicaissons. Provisions in the pending NYC building code will allow borehole video inspection in lieu of load testing. The ?new? technology results from the marriage of several well established methods: rotary duplex well drilling, high capacity micropiles and high capacity reinforced concrete building columns.

Jan 1, 2007

By Ryan P. Sullivan, G. Alan Klevens, Jian Huang

"BACKGROUNDLake Hamilton in Hot Springs, AR was created in 1932 when the Arkansas Power and Light Co. completed Carpenter Dam on the Ouachita River to generate electricity. Today, the 7,200-acre (2,914 hectares) impoundment is one of Arkansas’s most popular recreational and residential lakes.U.S. 70 crosses Lake Hamilton by means of a seven-span bridge featuring nine steel girders per span. Constructed between 1982 and 1984, the 1,410-foot long (430m) bridge carries four lanes of traffi c across the lake. The bridge is supported by six intermediate reinforced concrete piers composed of hammer heads, stems, footings and seals, which sit on the underlying rock. (See Figure 1). The bridge rises to a maximum of 33 feet (10m) above the surface of the lake and the footings and seals extend a maximum of 29.5 feet (9m) below the surface of the lake. The seals are situated on hard, fractured sandstone and shale.Routine underwater inspections in 1993 revealed large cracks in the lean seal concrete and refl ective cracks in the reinforced concrete footings. Infrastructure Engineers, Inc., The Arkansas State Highway and Transportation Department’s (AHTD) design consultant, then conducted an in-depth underwater inspection of the pier foundations. The investigation included cross-hole sonic logging, singlehole sonic logging, visual examination and strength testing of core samples, and petrographic analysis.The investigation revealed extensive cracking and low-strength concrete within the seals of all intermediate pier foundations. Many voids within the seal concrete had become fi lled with silt. There was evidence of continued seal deterioration between underwater inspections.AHTD and its engineers considered three rehabilitation solutions in the preliminary engineering stage: micropiles, a cofferdam supported concrete jacket, or a pile supported concrete jacket. The three alternatives were estimated to cost $1,250,000; $4,320,000; and $3,030,000 respectively. All three options would transfer the loads from the pier footing directly to the rock below, bypassing the seal concrete."

Jan 1, 2007

By Ryan P. Sullivan, G. Alan Klevens, Jian Huang

"BACKGROUNDLake Hamilton in Hot Springs, AR was created in 1932 when the Arkansas Power and Light Co. completed Carpenter Dam on the Ouachita River to generate electricity. Today, the 7,200-acre (2,914 hectares) impoundment is one of Arkansas’s most popular recreational and residential lakes.U.S. 70 crosses Lake Hamilton by means of a seven-span bridge featuring nine steel girders per span. Constructed between 1982 and 1984, the 1,410-foot long (430m) bridge carries four lanes of traffi c across the lake. The bridge is supported by six intermediate reinforced concrete piers composed of hammer heads, stems, footings and seals, which sit on the underlying rock. (See Figure 1). The bridge rises to a maximum of 33 feet (10m) above the surface of the lake and the footings and seals extend a maximum of 29.5 feet (9m) below the surface of the lake. The seals are situated on hard, fractured sandstone and shale. Routine underwater inspections in 1993 revealed large cracks in the lean seal concrete and reflective cracks in the reinforced concrete footings. Infrastructure Engineers, Inc., The Arkansas State Highway and Transportation Department’s (AHTD) design consultant, then conducted an in-depth underwater inspection of the pier foundations. The investigation included cross-hole sonic logging, singlehole sonic logging, visual examination and strength testing of core samples, and petrographic analysis.The investigation revealed extensive cracking and low-strength concrete within the seals of all intermediate pier foundations. Many voids within the seal concrete had become filled with silt. There was evidence of continued seal deterioration between underwater inspections.AHTD and its engineers considered three rehabilitation solutions in the preliminary engineering stage: micropiles, a cofferdam supported concrete jacket, or a pile supported concrete jacket. The three alternatives were estimated to cost $1,250,000; $4,320,000; and $3,030,000 respectively. All three options would transfer the loads from the pier footing directly to the rock below, bypassing the seal concrete."

Jan 1, 2007

By T. Wulleman, M. Ansriou

Integrity testing is a primary quality control check on a product that is for the most part not accessible to visual examination. Their cost can be expensive when using direct methods of inspection (like coring a pile) or more economical when using indirect methods (e.g. acoustic testing). All indirect methods operate by “inference” which means that they do not directly measure the defect of integrity. Indirect methods measure the variation of physical values (temperature, impedance, speed, ect.) correlated to the integrity of the pile allowing the detection of integrity defects, although these methods do not allow for the characterization of the defect. 1. INTRODUCTION Cast-in-place piles are particularly prone to integrity defects. The reasons for this are multiple, including lack of high quality of contractor workmanship, experience and supervision necessary in construction, variable soil and groundwater conditions on site, etc. Furthermore, visual inspection of the finalized pile is usually impossible. Therefore, special care has to be taken both during the execution process and during the subsequent quality control campaign to detect any defects of executed piles. Today, a lot of methods do exist to assess pile integrity. It is thus essential to understand the mechanism governing those devices to both make an engineering choice of the pile integrity testing method and to interpret correctly the provided results. 2. QUALITY IN PILE FOUNDATIONS 2.1 Pile anomalies A pile having an anomaly is a pile which has a different behavior from what is normally expected. The presence of a pile anomaly does not necessarily imply that a pile cannot be used for its intended purpose (Gordon & Chapman 2004). An anomaly can be considered as a defect, or a “performance” depending on the ability of the pile to fulfil the following three criteria (3C): C1 - Meet the Service Limit State (SLS) requirement and support the proposed working load without settling more than admissible by the superstructure ; C2 - Meet the Ultimate Limit State (ULS) requirement and carry a specified load with an adequate factor of safety against failure ; C3 - Remain durable throughout the design life of the structure such that the pile is not affected by time dependent activities (chemical attack, corrosion of steel reinforcement, ect.), which would jeopardize its ability to maintain its compliance with the first two criteria.

Jan 1, 2019