Search Documents

By E. Ilgar

"Deposition studies were conducted in acid copper electrolyte to determine the influence of chloride ions on cathode morphology. A statistically designed screening test was carried out in the absence and presence of 20 ppm CI- using a three factor, two level factorial design, in an electrolyte containing 36 gl'! Cu2+ and 150 gl-! H2S04, The independent variables evaluated were agitation; current density and temperature and their influence on surface roughness was determined. The copper deposited at current densities where activation was the primary control mechanism appeared similar in morphology whether stirring was used or not. The addition of 20 ppm CI- to the electrolyte gave rougher deposits under the same conditions. In the mixed control regions, considerably rougher, dendritic deposits were obtained when CI- was present. Agitation was effective in reducing the copper surface roughness both in the apparent activation and mixed control regions in the presence ofCI-. The results of this study showed that 20 ppm Cl- polarized the copper deposition at low overpotentials but caused depolarization at higher overpotentials.IntroductionChloride ion is inherently present in copper electrolyte, either as an additive or from other sources such as make up water. The behavior of the chloride ion is well documented in electrorefining operations, but its role in copper winning is less obvious. However in both cases there is evidence that cathode growth and solution chemistry are strongly influenced by its presence. The mechanism and electrochemical action of the Cl"" have been shown to be very complex, therefore a better understanding of its influence on electrocrystallization is essential for improved cathode deposit growth control. It was proposed that Cl"" polarizes the copper deposition reaction at low concentrations due to CuCI formation but depolarization occurs at higher concentrations due to the formation of a soluble CuCI2"" complex [1,2]. Franklin [3] reviewed the mechanism of additives in the electrodeposition process and proposed that the Cl"" complexed with copper, adsorbed on the cathode as an induced anion leading to an increase in the reduction rate. At cathodic overpotentials less than 100 mY, lppm NaCl had a polarizing effect, i.e. an increase in impedance of the charge transfer step. At higher Cl"" concentrations up to 100 ppm, depolarization occurred as evidenced by a decrease in impedance, which was attributed to soluble cuprous complexes [4]."

Jan 1, 1997

By T. Mason, R. Macko

Electroless nickel (EN) coatings are widely used in the manufacture of automotive parts, providing uniform coating, corrosion protection, wear resistance and lubrication. In contrast to EN plating benefits, the disposal and treatment of waste solutions can cause many difficulties. The use of electrochemical treatment technology greatly improves _the operation of the main wastewater treatment process and reduces operation costs. A new, state-of-the-art job shop in the Chicago area, which provides EN plating for the automotive industry, has installed a large separated electrolytic cell for the treatment of spent EN solution (from dumps and wastewater). The waste/wastewater is handled by the separated electrolytic cell, batch treatment system, filter press and neutralization station. The implementation of modem electrolytic technology and auxilliary equipment provides an effective waste treatment process that meets environmental compliance criteria.

Jan 1, 2000

The present work is mainly focused on developing intermetallic inert anodes for aluminum electrolysis. The anode alloy based on Al-Ti-Cu system was prepared by casting, followed by the application of a protective coating. Behaviour of corrosion and the passivation under anodic condition was characterized using the electrochemical and microscopic techniques. The results obtained clearly demonstrate that the oxide coating can provide good corrosion resistance via surface passivation of alloy anodes, rendering them inert in cryolite melt.

Jan 1, 2006

By C. M. F. Viera

In this work the properties of a clayey ceramic incorporated, up to 10 wt.%, with three types of wastes from a water treatment plant was evaluated. To determine the physical and mechanical properties such as linear shrinkage, water absorption and diametrical compression, specimens were prepared by 18 MPa uniaxial pressure and then fired in laboratory furnace at 700oC. The results indicated that the wastes incorporation changed the properties of the clayey ceramic. From the results it was found it possible to recycle these wastes into clayey ceramic in low amounts to avoid deleterious effect on the quality of the fired product.

Jan 1, 2008

By V. Ramachandran

In view of the increasing environmental regulations that have been promulgated in the last 30 years, non-ferrous smelters and refineries have learnt to handle effectively the process waste streams that need to be bled from the system for impurities' control The cations of concern are copper, lead, zinc, cadmium, mercury, thallium, nickel, silver, sodium and potassium. Anionic species of arsenic and selenium also need to be addressed, Sulfates and chlorides-not a major concern at present-have come under scrutiny in the recent past. The current paper reviews several treatment options with reference to a) types of waste streams processed b )process chemistry c)discharge options and recovery of treated water and d) sludge disposal The long term goal of any smelter and/lor refinery should be to achieve zero liquid discharge from the plant. Methods to obtain zero discharge are discussed.

Jan 1, 2003

By Dave Tahija

"Many investigations are being performed with the goal of removing carbon dioxide from the atmosphere and permanently storing it in geologically stable settings. At the same time, carbon dioxide in the form of dissolved carbonate is steadily accumulating in the world's oceans. Both carbon dioxide sequestration and oceanic accumulation are constrained by the aqueous thermodynamics of the carbonate system. These constraints are illustrated using the STABCAL computer model to generate potential-pH and aqueous distribution diagrams of seawater in contact with various pressures of carbon dioxide gas. STABCAL diagrams and titration simulations are also used to model some potentially useful cation-carbonate sequestrationsystems.IntroductionAtmospheric carbon dioxide concentrations have risen dramatically in the past couple of centuries and are rising still, primarily as a result of human activities, especially the burning of fossil fuels. Increased atmospheric carbon dioxide concentrations have been implicated as a main cause of global warming but have other effects as well.Rising levels of atmospheric carbon dioxide result in increased concentrations of dissolved carbonate complexes in water, including the oceans. These dissolved carbonates interact with other dissolved substances, altering overall seawater chemistry, most noticeably causing lowered pH levels.Some of these chemical changes are observed directly, for instance the general drop in oceanic pH, [1], while others can be inferred and predicted using thermodynamic modeling. The chemistry of dissolved carbonate in seawater is not especially intricate, as such chemical systems go, but neither is it simple enough to be worked out on the back of an envelope. Interactions between the several simple carbonate species and all the major dissolved cations in seawater should be considered, as well as the effects of competing anions, especially chloride and sulphate, since they are much more abundant than carbonate in seawater."

Jan 1, 2011

By C. A. Silva

The kinetics of chlorination of titanium-bearing raw materials has been investigated. For comparison purposes pellets of controlled macro-porosity, made of analytical grade TiO2 and anatase concentrate (Brazil) , have been exposed to different combinations of gas composition - CO, CO2, C12 -, gas flowrate and temperature. A thermogravimetric technique and an adapted grain model have been used in order to assess the influence of the several experimental parameters upon the chlorination behavior.

Jan 1, 1997

By Yiling Zhang, Paul A. Salvador, Gregory S. Rohrer

"Photocatalysis utilizes solar energy to produce hydrogen by splitting H2O. When a thin film of photocatalyst TiO2 is supported on a ferroelectric BiFeO3 substrate (band gap ~2.5 eV), the TiO2/BiFeO3 heterostructure is capable of photochemically reducing Ag+ to Ag0 in aqueous solutions under blue light with enhanced efficiency. The observation of spatially selective silver patterns on surface of the heterostructure after reaction suggests that photogenerated electrons and holes in ferroelectric BiFeO3 are driven in opposite directions to reduce their chance of recombination. Comparisons of the amounts of reduced silver on TiO2 film grains with distinct phases/orientations show that the reactivity is mildly preferential on anatase TiO2 phase and does not strongly depend on crystallographic orientation of BiFeO3.IntroductionTitania (TiO2) is capable of photocatalytically converting H2O to hydrogen and oxygen under the irradiation of ultraviolet light. [1, 2] One of the limiting factors for titania to be used as an effective photocatalyst is its band gap. Because the absorption edges of rutile and anatase titania are at 3.0 eV and 3.2 eV, respectively, they can only absorb light in the UV portion of the spectrum, which is about 3% of the available solar energy. [3-5] This limitation has motivated attempts to modify the absorption edge of titania so that it can absorb visible light.One strategy is to substitute a portion of the titanium and/or the oxygen with other atoms. There are numerous reports on visible light absorption of titania by doping and co-doping of Cr, V, Mo, Sb, Fe, N, S, C, and F. [6-34] Another strategy is to add an adsorbed molecular species that absorb visible light and donate an electron or hole to the titania, such as organic dyes [33, 35, 36] and Ce3+/Ce4+. [37, 38]The strategy in the present work takes the approach of depositing a pure titania thin film on a visible light absorbing substrate BiFeO3 to induce visible light activity of the heterostructure. BiFeO3 is a semiconductor with a band gap of about 2.5 eV [39-41] and is photocatalytically active in visible light. [42, 43] It is also ferroelectric with spontaneous polarization along pseudo-cubic <111> directions of 6.1 µC cm-2. [44] The spontaneous polarization gives rise to internal electric fields that drive photogenerated charge carriers, namely electrons and holes, in opposite directions to reduce their chance of recombination. [45-47] Additionally, the separation of electrons and holes leads to the spatial separation of reduction and oxidation half reactions so that the back reaction of intermediates is also suppressed. Such charge carrier separation has been reported in TiO2/BaTiO3 heterostructures with UV light illumination. [48-51] The TiO2/BiFeO3 heterostructures in this work combine both advantages of the relatively narrow band gap and the internal fields in BiFeO3 to enhance the overall photocatalytic activity."

Jan 1, 2014

By Jing Zhong, Yugang Li, Chen Yan, Shaoda Zhang, Qian Wang

Online surface quenching technology has been developed for the hot charging process to prevent the surface cracks in high strength low-alloy steel slabs. In this paper, a two-dimensional heat transfer model of surface quenching process was presented. This finite element model includes nonlinear thermodynamic properties, by which the slab temperature distributions were computed. The model predicted temperatures show reasonable agreement with the measurements. The effects of the water flow rate and slab movement velocity on temperature variation during the quenching and subsequent tempering process were investigated. The result shows that the temperature drop increases but the tempering temperature changes slightly with increasing water flow rate and decreasing slab velocity. Keeping the slab movement velocity at 1.2-2.1m/min and the water flow rate at 55-70m3/h, the slab surface experiences a temperature drop of 400-600 firstly, then recovers above 650, the quenching and energy-saving effect are remarkable.

Jan 1, 2015

By Esa J. Peuraniemi

Copper smelting to form blister in one single step has been possible for a long time even from low grade concentrates. In spite of obvious benefits, it has been economically viable only with few special raw materials having high enough Cu/Fe and Cu/S ratio. Outokumpu Blister Flash Smelting is currently applied at three operations, and three others will be commissioned in the near future. With typical chalcopyrite concentrates two main obstacles have prevented wider adaptation of direct blister processing: slag formation and heat generation. Oxygen potential in the reaction shaft must be high in order to produce blister with targeted sulfur content below 1%. When large amount of iron is oxidized, as well as sulfur, copper is inevitably also oxidized into slag. High copper amount in substantial tonnages of slag lead on to costly down stream recovery operations to obtain discardable slag. Almost complete oxidation of sulfur and iron releases a high amount of heat which traditionally has been solved by lowering oxygen enrichment of the blast leading on to oversized off-gas line and acid plant. One challenge in direct blister smelting relates to the attack of aggressive high-copper containing slag against furnace refractory lining. In continuously operated Outokumpu Direct Blister Flash Smelting this is taken care of by preventing vigorous melt movement in the settler. Stable bath conditions and stationary slag against refractory lining enable the formation of a protective autogenous layer between aggressive slag and vulnerable refractory. These direct blister smelting challenges are addressed from equipment and process development point of view. New solutions to overcome the obstacles are presented and discussed.

Jan 1, 2006

By Brandon R. Ball

An investigation of the effects of ozone and ozone-induced hydroxyl radical on reducing whole effluent toxicity is described and discussed relative to the application of ozone for industrial water treatment. Results from operation of an ozone system treating industrial effluent from a lead and zinc mine in Colorado are presented. The mine discharges 1,000 gpm of wastewater into a tributary of the Arkansas River and has historically exceeded Whole Effluent Toxicity (WET) limits and on occasion has exceeded numeric limits for copper, ammonia, and cyanide. Based on results of a Toxicity Identification Evaluation (TIE) conducted on the effluent and individual process waste streams, the source of effluent toxicity is believed to be primarily associated with organic reagents used in the milling process. Based on test results, an applied ozone to COD ratio of 3: 1 by weight and a contact time of 30 minutes was found to be effective for reducing whole effluent toxicity at pH 11 but not at pH 7, indicating oxidation by hydroxyl radical to be the dominant mechanism responsible for toxic-ity reduction. At an applied ozone to COD ratio of 3:1 and a pH of 11, toxicity was improved from 0 percent survival to 100 percent survival for Ceriodaphnia dubia and fathead minnow (Pimephales promelas) based

Jan 1, 1996

By D. S. Barr

The Freeport McMoRan chlorination circuit is comprised of four related processes: ore chlorination, gas scrubbing, chlorine supply and excess hypochlorite removal ("hypo kill"). Each of these processes are described, and related to the pertinent mineralogic components in the carbonaceous ore feed to the plant. The chlorination system in use at Jerritt Canyon to passivate forms of preg-robbing organic carbon has proven to be a cost effective and efficient means to recover gold from low sulfide carbonaceous refractory ores, where gold may not be specifically associated with either the sulfides or the carbon.

Jan 1, 1987

By Tracy Lucas, Ian Hamill

"Issues of importance in the area of continuous casting centre around product quality. This can be affected by particle inclusions transported into the mould from upstream processes and by draw-down of particles from the meniscus. Turbulence of the meniscus can increase the latter and is also detrimental to product surface quality.Suitably validated Computational Fluid Dynamics (CFD) modelling can provide the operator with an efficient tool with which to investigate the effects of changes to the design and operation of the caster and associated plant.In this paper, examples are presented of the use of the CFD software, CFX, to simulate:•,free-surface shape and turbulence in the mould using deforming meshes•,solidification in the mould using a fixed-grid, source-based method•,argon gas injection through a submerged entry nozzle using a full multiphase model•,inclusion motion and removal in tundishes using an algebraic slip model.The CFD simulations of the free surface shape are complemented by detailed Particle Image Velocimetry measurements performed on a full-size water model of a thin-slab mould and upper strand. Close agreement is demonstrated between the predictions and experiments."

Jan 1, 1999

By K. D. Peaslee, V. L. Richards, C. H. Rawlins, S. N. Lekakh

"Steel-making processes generate carbon dioxide air emissions and a slag co-product. The aim of this project was to develop a functional sequestration system using steelmaking slag to permanently capture carbon dioxide emitted in steelmaking offgas. A possible parallel benefit of this process would be rapid chemical stabilization of the slag minerals with reducing swelling or leaching.This paper summarizes the original results of the project, including mineralogical and structural features of carbon sequestration with steel making slag, mathematical modeling of reaction phenomena using a modified shrinking core model, METSIM modeling of several possible industrial applications, a thermo-gravimetrical study of the reaction between slags and different gases, and design and testing for a lab scale apparatus consisted of two reactors.1. IntroductionThe U.S. produces 9-14 Mt of steelmaking slag annually, which represents approximately 10-15 wt. % of crude steel output.1,2 Primary uses for steelmaking slag include high quality mineral aggregate, Portland cement, unconfined fill, soil conditioning, and pH neutralization of abandoned mine drainage.3,4 The key factor prescribing slag use is the alkaline-earth metal (e.g. Ca and Mg) oxides content, which contribute to overall basicity and cementitious strength. However, as-produced steelmaking slag is chemically unstable. Calcium and magnesium oxides readily form hydroxides and carbonates through reaction with atmospheric gases. Both hydroxide and carbonate formation produce substantial mechanical swelling leading to heave failure in confined construction applications, thus many states dictate stockpile aging for 3-6 months prior to commercial use.5,6 Sequestration of carbon dioxide is a natural corollary to forced carbonation. The conversion of CaO/MgO to carbonates serves both to stabilize the slag, and permanently capture and store the CO2."

Jan 1, 2008

By Jincheng Hu, Honggang Zhong, Qijie Zhai, Congsen Wu, Cheng Zhang, Jingzheng Ye

"The influence of cooling intensity on the solidification structure and ferrite phase content of a new duplex stainless steel (DSS) was investigated by using a thermal simulation setup for continuous casting. The results showed that the characteristics of the solidification structure were similar to their industrial scale manufactured slabs, including chill zone, colunmar zone and equiaxed zone. And austenite morphologies were mainly primary and secondary Widmanstatten sideplates as well as intragranular Widmanstatten plates. In addition, it revealed that the ferrite content increased with an increasing distance from the chill surface and decreased at colunmar to equiaxed transition (CET) position, then the value remained relatively stable at equiaxed zone. Furthermore, the ferrite content presented the same trend with the cooling intensity ranging from 100 mL/min to 2000 mL/min with the values just varying in a slight range.IntroductionThe duplex stainless steel (DSS) is the kind of steel that ferrite phase and austenite phase occupy about 50% respectively, or the content of the fewer phase has to be more than 30% [l]. The success of modem duplex stainless steels is to a large degree due to their higher strength than austenitic stainless steels, higher toughness than ferritic stainless steels, good weldability and high resistance to stress corrosion cracking as well [2,3]. The cost of stainless steel production continues to soar in recent years due to the increasingly higher price of Cr. In order to decrease the production cost, a new type of duplex stainless steel was developed by Bao steel [4]. This newly developed duplex stainless steel had low Cr content compared with 2205 DSS, and was expected to be applied into automobile industry. However, this type of steel was still in the initial stage of development, and the influence of continuous casting process on its solidification process and structure was still unclear, which needed to be studied further. Several works published in literature presented the effect of continuous casting conditions on duplex stainless steel (DSS) 2205, 2304 [5,6]. It was discussed that the cooling intensity in the chill-side had little efficient influence on the phase transformation. In this paper, the effect of cooling intensity on the solidification structure and ferrite volume fraction of this DSS at a given cooling rate was investigated."

Jan 1, 2014

By I. D. Reznik

Regularities of cobalt and nickel distribution between slag and matte, slag and metallic alloy on the base of concepts on exchange reaction equilibrium are considered. It is shown that the distribution of cobalt and nickel in industrial processes approaches to equilibrium one. Oxysulphiae influence on the bahaviour of cobalt, nickel and sulphur is shown. The recommendations on conduction of the processes of smelting, converting and slag cleaning based on the analysis of the methods or" non : ferrous metal separation from iron are given.

Jan 1, 1993

By Kenneth N. Pike

The need to comply with environmental regulations and increase production has resulted in modifications to the East Penn blast furnace operation. Changes made include furnace design modifications, closed loop water cooling with heat recovery, automated weighing and charging, automated tuyere punching, ammonia scrubbing of tail gases and improved metal and slag handling to minimize environmental impact. These changes have resulted in a marked increase in yearly production and compliance with many of the air, water and solid waste regulations.

Jan 1, 1990

By Kuo En Chang

Many rare earth - transition metal (RE-TM) compounds absorb/desorb hydrogen reversibly at room temperature and atmospheric pressure. For LaNi5 which is used as a battery material, the electrochemical nature of this process is well known. In the case of Nd-Fe-B which has found wide application as a powerful permanent magnet, the absorption of hydrogen has both significant advantages and disadvantages. However, a fundamental understanding of the hydrogenation process at ambient temperatures and its effect on subsequent corrosion behavior is currently lacking. This paper reports the results of the hydrogenation of NdFeB two alloys, (NdDy)15Fe78.3A10.7B6 and (NdDy)15Fe67Co5V4A12B7, which are compared with that of LaNi5. Results show that hydrogenation can be accomplished by either electrochemical methods or immersion in dilute sulfuric acid. For the latter method, the change in lattice parameter indicates that the level of hydrogen absorbed by the NdFeB particles corresponds fairly closely to an overall composition of Nd2Fe14BH2.7. Cyclic electrochemical charge/discharge experiments show that the maximum hydrogen discharge capacities of the NdFeB, NdFeB-Co-V, and LaNi5 are 40, 60, and 210 mA?h?g-1, respectively. Anodic potentiodynamic polarization measurements and calculated values of icon reveal that absorbed hydrogen in NdFeB-Co-V and the NdFeB may lead to significant increases in corrosion rates.

Jan 1, 1995

By H. L. Fraser

A review of the possibilities of performing microchemical analysis in thin sections using a combination of scanning transmission electron microscopy and energy dispersive spectroscopy of x-rays is given. Particular attention is paid to the factors that limit accurate analysis at the highest spatial resolution. As an example of the use of these techniques applied to a potential problem in minerals processing, the identification of iron pyrite and pyrrhotite particles in Illinois, Herrin #6 coal is presented.

Jan 1, 1981

By Metehan Erdogan, Ishak Karakaya, Fuat Erden, Emre Ergül

"The FFC Cambridge process was suggested as a promising Si production technique for the expanding solar energy industry. Direct electrochemical reduction of bulk SiO2 plates and porous SiO2 pellets in molten CaCl2-NaCl salt mixture were investigated at 750°C by applying 2.8 V potential difference. The produced Si powder was brown and found to be contaminated by the Ni and stainless steel plates used as the cathode contacting materials. The reduction rates of the bulk SiO2 plates and porous SiO2 pellets were compared from variations of current and accumulative electrical charge that passed through the cell during the electrochemical reduction. The amorphous bulk SiO2 plates were reduced slightly faster than porous pellets of crystalline SiO2. The overall reduction potential of SiO2 pellets against the graphite anode at 750°C in molten CaCl2-NaCl salt mixture was determined as 2.3 V by cyclic voltammetry. This potential was supported by calculations.IntroductionMetallurgical grade Si cannot be directly used in electronic industry and some intermediate steps are required to produce industrial solar grade silicon (SOG-Si). A promising alternative solar grade silicon production technique is the FFC Cambridge Process [1]. Production of Si by electrochemical reduction of SiO2 at 850oC in molten CaCl2 electrolyte was first studied by Nohira et.al. [2]. In their study; Si formation was observed on bulk SiO2 cathodes after 1 hour of electrolysis. Complete electrochemical reduction of porous SiO2 pellets was first reported by Jin and his coworkers [3]. The mechanism of electrochemical reduction of SiO2 to Si in molten CaCl2 was explained in another study [4]. Reduction rates of bulk SiO2 and porous SiO2 pellets were also compared previously and it was found that reduction rates for bulk plates were higher [5]. Furthermore, it was reported that mixing Si into porous SiO2 pellet increased the reduction rate [5]. Mo [2, 4-7], Ni [3, 8, 9] or Si [6] were used as cathode contacting materials in various studies. Yasuda et. al. [6] produced Si with 99.80 % purity using Si plates as cathode contacting material to reduce metal contamination."

Jan 1, 2012