Search Documents

By Paul Weir

PRODUCTION METHODS in the bituminous coal mines in the United States are undergoing many changes. Although the primary object of these changes is the production of a better product at a cheaper cost there are other considerations such as the improvement of conditions under which miners live and work. The almost complete unionization of the manual workers in the industry during the past four years has 'brought with it a stabilization of wages on a relatively high basis and of hours of work per day and per week on a relatively low basis. With differentials in wages between producing districts firmly established, and with a nation- wide and uniform application of in-

Jan 1, 1937

By Elmer R. Kaiser

COMBUSTION of coal and transfer of heat from flames and gases to boiler surfaces continue to be of great interest to engineers here and abroad. Numerous investigations have been in progress to improve furnace and boiler performance and economy. The importance of better understanding of the processes and opportunities for improvement is apparent when it is remembered that heat from at least 500 million tons of coal a year the world over is being transferred to boiler water at efficiencies ranging mostly between 50 and 90 pct. Even slight gains in efficiency, economy, and labor saving become very significant when multiplied by the enormous quantity of fuel consumed. Also the competitive position of the large coal, oil, and gas industries in satisfying the fuel consumers is greatly affected by the achievements made through technical progress with each fuel. This paper is part of a continuing activity of Bituminous Coal Research, Inc., to extend the knowledge of coal utilization for steam generation and to seek promising directions for future research and development in cooperation with others. Particularly in the latter regard, numerous interviews were held during the last three years to seek the experience and advice of boiler and combustion-equipment manufacturers, electric-utility executives, and fuel engineers. A wealth of published information was also reviewed, which together with the interviews pointed to the advisability of further work on ash and sulphur control. For the present purpose a number of factors important to efficient heat liberation and recovery have been grouped as follows: 1—combustion, temperatures, and rates of heat liberation; 2—radiation, convection, and furnace and boiler configuration; 3—sponge ash, slag, and hard-bonded deposits; 4— low-temperature deposits and corrosion (cooling flue gas below dew point and air-pollution control); 5—the limitations of coal cleaning and boiler size and cost as related to fuel characteristics; 6—future possibilities and conclusions. The development of combustion apparatus for power boilers is progressing at a lively pace. There has been no letup in improvements in design of pulverized-coal-fired boilers, and there is a strong trend at present toward improving dry-bottom units. Spreader stokers with overfire jets and dust collectors as standard equipment are gaining favor. Less than 10 years in commercial use, cyclone burners are going into numerous installations here' and abroad.' Underfeed and traveling-grate stokers have long since been developed for heavy-duty operation, yet new developments in overfire jets and humidification of air blast have improved their performance. A water-cooled vibrating-grate stoker of German origin is being introduced into the United States and Canada." The primary objectives of an ideal coal combustion device are: capacity to burn the variety and sizes of coals likely to be economically available during the life of the unit; capacity to burn the coals automatically for a wide load range and rapid load fluctuations and to burn the coals completely to CO2, H2O, and SO2, which means without smoke and cinders, or carbon in the refuse; capacity to control and discharge all the ash in final granular form without ash adhesion to walls or tubes, and without flue dust; minimum furnace volume; minimum labor and maintenance; low initial and operating cost. Regardless of the method of burning, the gaseous products of coal combustion are N2, CO2, O2, H20, and SO?. By way of illustration, the coal analyses in Table I is assumed from an installation described by E. McCarthy.' When coal is burned with 20 pct excess air (theoretical air, 9.23 lb per lb of coal), the quantities of combustion gas shown in Table II are produced. In addition, the gases carry particles of fly ash, unconsumed cinders, soot particles, and small but significant amounts of vaporized oxides and sulphates of sodium, potassium, lithium, phosghorous, iron, and other metals. In recent years, germanium, one of the rare metals found in coal, has been shown to oxidize and vaporize at combustion temperatures and to be concentrated by reconden-sation at lower temperatures." Pulverized coal and cyclone flames" have peak temperatures of 3000' to 3500°F. Temperatures in fuel beds of large underfeed stokers reach maxima of 3000°F, sufficient to fuse almost any ash and to volatilize some of it. These peak temperatures are above the optimum necessary for rapid combustion, but they hasten heat transfer for ignition as well as boiler heat absorption. Furnace and gas temperatures increase with combustion air preheat. Low excess air has the same effect. Fine coal pulverization and highly turbulent combustion shorten the distance for fuel burnout, increase flame temperature, and speed up heat transfer. Rates of combustion of pulverized coal exceeding 200,000 Btu per cu ft per hr have been demonstrated in atmospheric gas-turbine combusters,

Jan 1, 1955

By Robert M. Dreyer

AGGREGATE With an annual domestic production of over 1.6 billion tons at a value of over $2 billion (see Table 15.1.1), the production of aggregate (crushed rock, sand, and gravel) is a basic industry of utmost economic importance. Because of the role of aggregate materials as essential ingredients of concrete, asphalt surfacing, and plaster, their delivered prices are major factors in determining the cost of construction. The annual domestic production comes from nearly 10,000 plants. About 15% of these plants account for over one-half the production. In a rapidly inflating economy, the average mine sales price of aggregate has remained relatively stable. The actual mine sales prices, however, vary greatly depending on quarrying costs in various parts of the country. Of much more importance in construction costs, however, is the delivered price of aggregate. This varies for each job, depending on the distance from the quarry and resulting transportation costs, as well as the initial cost at the mine. Because of a proliferation of regulations limiting new quarries in the vicinity of the encroaching urban sprawl, the average distance which aggregate must be transported has been increasing rapidly. Although it is impossible to derive an average delivered cost for aggregate, it should be noted that even an increase of only $1 per ton in average delivered cost over the last decade (probably a minimal assumption) would mean an annual cost $1.5 billion higher than ten years ago. In recent years, structural engineering considerations, as well as an increasing use of lightweight concrete blocks, have resulted in a rapidly increasing demand for lightweight concrete and plaster, the essential ingredient of which is lightweight aggregate. Principal lightweight aggregates are: pumice, slag, perlite (thermally expanded hydrous volcanic glass), vermiculite, and expanded shale, formed by the thermal expansion of shale and slate. The United States now has the capacity to expand, annually, over 13 million tons of shale and slate and to expand over 600,000 tons of perlite. In locating a site for aggregate production. the following factors must be considered: (1) tonnage available; (2) quality of aggregate (including local variations); (3) distance from major use areas; (4) transportation costs, including those resulting from present and possible future haulage restrictions; (5) zoning regulations; (6) operating costs, including the cost effects of compliance with local regulations governing blasting, air pollution, water pollution and drainage, noise levels, and operating periods. At one time, locating a suitable site for the production of crushed rock, sand, or gravel, in most areas, was regarded as an extremely simple task. In the past few years, however, finding a site for profitable production of aggregate has assumed ever-increasing com-

Jan 1, 1976

By D. W. G. White

The surface tension of zinc has been determined by the sessile-drop method in a progvam emphaszzing detailed experimental care. The surface tension oj. the pure metal was measured over a range of ternperature from the melting point (419.6"C) to 540°C. At the melting point, the suvface tension of zinc was found to be: 1) 99.99+ pct Zn - 757.0 5 dynes per cm 2) 99.999+ pct Zn - 761.0 5 dynes per CI 3) 99.9999 pct Zn - 76'7.5 5 dynes pev cna From experiments carried out in a closed, isothermal cell, the temperatuve coejyicient of the surface tension (6y/6T)p, , of zinc xas found not to be negative but to be postiue. A positive tenzperatre coefficient indicates a greater depee of order in the surface than in the body of the lquid. Houlezer, by delibevately inducing continuous zaporization, a temperature coefficient of su)face tension with a negative slope can be produced. The work reported herein was undertaken as part of a larger program of fundamental research on the properties of molten zinc and zinc alloys. This program grew out of a continuing interest at the Mines Branch in the behavior of liquid metals in the foundry and of a desire on the part of the zinc industry for reliable basic data. The work was originally begun in cooperation with the Consolidated Mining and Smelting Co. Ltd., Trail, B.C., and was subsequently continued from 1960 to date in association with the Canadian Zinc and Lead Research Committee and the International Lead and Zinc Research Organization. Although the surface tension of liquid zinc has of course, been measured before, as Table I and Fig. 1 demonstrate, there is not good agreement among the existing values. Such disparities arise because sources of experimental error are insufficiently controlled. This situation places the reader in doubt. One result may be correct within narrow limits—even fortuitously—yet, because there is not agreement between several values, none can be accepted with conviction and all become suspect. It seemed, therefore, in the circumstances, that there was room for further work embodying considerable emphasis on experimental care in order that, within a small margin of error, an accurate value might be obtained. It was in this spirit that the work was undertaken. METHOD The sessile-drop method -as adopted for this work. In this method, when applied to liquid metals at elevated temperatures, the outline of the meridional section through a drop resting freely on a horizontal surface is recorded photographically. Certain parameters

Jan 1, 1967

By A. N. Chirico

This paper reviews the three major distillation processes: multiple effect (LTV) evaporation, multi-stage flash distillation and vapor-compression forced circulation evaporation. Scale preventative measures are discussed for all saline water applications. Operational data is presented on the Freeport, Texas, demonstration plant, which is the first government facility to produce one million gallons per day of fresh water for a municipality. There has been much publicity concerning the water crisis that confronts many peoples today. There is little doubt that the arid regions - which include the Middle East, parts of Africa and the Caribbean — have suffered to no slight extent for the lack of this most precious commodity. But what about our own country? Government experts have extrapolated demands and flatly predict that by 1980 we will be faced with a shortage of 80 billion gal per day. The validity of this prediction has been disputed by others; however, it appears certain that there will always be a natural abundance in some areas, a shortage of supply in other areas. Distributing our total natural water resource equitably would be impossible. Transmission of water by means of aqueducts can be an expensive undertaking. The controversial Feather River Project in Calif. is an example. The estimated cost for this venture is a staggering three billion dollars. As our population continues to increase and our standard of living rises, agricultural and industrial requirements will be proportionate. What can be done to avoid a crisis? We can conserve and use our water for industrial and irrigation purposes more judiciously: we can attempt to eliminate pollution of our natural resources from sewage and industrial wastes; we can develop, while there is time, saline water conversion processes for the massive production of low cost fresh water. The scope of this paper will be limited to only the distillation type processes that are commercially feasible. The first step in making potable water is to find a source of raw material. An inexhaustible supply is provided by oceans in coastal regions, but the supply of water is more critical in the inland communities of our country. The source of raw material in these. regions is brackish well water and this must be utilized. There is a significant process difference when handling brackish water compared to seawater and this brings out an important fact: No single conversion method can be universally applied to solve all the water problems. Composition of the raw water and degree of distillate purity are factors which must be considered before a particular process is selected. Local conditions at the plant site, fuel costs, labor costs, disposal facilities, etc. are other equally important factors which must be evaluated. WATER CONVERSION PROCESSES Conversion processes commercially feasible today are: 1) multiple effect evaporation, 2) multiple flash distillation, 3) vapor compression distillation and 4) electrodialysis. The first three are distillation processes which take potable water out of the raw water, while the fourth is a membrane process which takes out the salt. In addition to the above there are a good number of other promising methods for production of potable water, many of them in the basic research stage. Freezing is another promising process with commercial potential. This process hinges upon the formation of ice crystals which are free of salt occulsions. Separation and washing of the crystals are problems that must be solved before this process can be considered commercially feasible. Freezing processes have several advantages mostly attributable to the low temperature of operation. This low temperature reduces the scaling and corrosion problems encountered in higher temperature operations. Several different freezing processes are being considered and will be tested in the pilot plant at Wrightsville Beach. One process is a flash freeze process, a second uses a secondary refrigerant such as butane for freezing, and a third process employs a secondary refrigerant particularly controlled to produce large ice crystals. Of the above processes, only the distillation processes are reliable when water of high purity is re-

Jan 1, 1963

By Hans-Jürgen Schaller, Horst A. Brodowsky

Activity coefficients of boron in palladium were determined at concentrations up to PdB0.23 by reducing B2O3 between 870" and 1050°C in a controlled H2-H2stream and measuring the resulting weight gain. The deviations from ideal behavior closely resemble those of the system Pd-H and are interpreted in terms of three principles: 1) The solute atoms occupy octahedral interstitial positions. 2) They donate their valence electrons to the 4 d and 5s bands of palladium, raising its Fermi energy. 3) The lattice strain energy is lower for two nearesl -neighbor interstitial particles than for two farther separate ones. SOLID solutions of hydrogen in palladium are a useful subject for studying thermodynamic aspects of the formation of alloys and of nonstoichiometric systems.1-3 The activity of hydrogen is readily measurable to a high degree of accuracy,4'5 even at low temperatures where the deviations from ideal behavior are more pronounced, and its simple structure facilitates an interpretation of these deviations in terms of a detailed model. Two effects are discussed to account for the non-ideal properties:3 An "electronic" effect, connected with the rise of the Fermi energy, as electrons of the interstitial hydrogen atoms enter the electron gas of the metal, and an "elastic" effect, due to an interaction of the regions of strain around each interstitial atom. The electronic effect is based on the idea that the lowest energy levels of the dissolved hydrogen atoms are higher than the Fermi energy, so that the electron will not occupy a localized state but enter into the electron band of the metal.6 The elastic effect is based on the observation that dissolved hydrogen distorts and expands the palladium lattice. The hypothesis is put forward that the elastic strain energy is lower for two adjacent dilatational centers than for two separate ones; i.e., they attract each other. The resulting pair interaction can be used to calculate an elastic contribution to the thermodynamic excess functions by means of one of the statistical methods. This model permitted a detailed description of the solution properties of hydrogen in palladium3 and in palladium alloys.798 An extension of the approach to describe the excess functions of substitutional palladium alloys is possible.9 In order to further test and refine the model, an investigation of other interstitial alloys was started. Palladium dissolves considerable amounts of boron in homogeneous solid solution.10 The palladium lattice expands linearly up to nB = 0.23 (nB = B/Pd atomic ratio), the highest concentration studied." The expan- sion, extrapolated for 1 mole of interstitial per mole of palladium, is 17 pct of the lattice constant of pure palladium vs 5.7 pct in the case of hydrogen.12 The fact that the lattice expands rather than contracts is a strong indication that interstitial positions are occupied. According to neutron diffraction experiments, hydrogen occupies the octahedral sites of the fcc lattice.13 Unfortunately, this direct evidence is not available for the Pb-B system, mainly because of the high-reaction cross section of boron with thermal neutrons. However, by way of analogy and on the grounds of the rather close similarities between the two systems to be reported here, it seems safe to attribute octahedral positions to the dissolved boron, too. At higher boron contents, compounds of stoichiomet-ric compositions are reported such as Pd3B, which has the structure of cementite,14 so that a close structural relationship seems to exist with the system r Fe-C. In their study of hydrogen absorption in Pb-B alloys, Sieverts and Briining noted that alloys with an atomic ratio of about nB = 0.16 are no longer homogeneous15 This observation was confirmed in an extensive X-ray investigation.11,16 The phase boundaries of two miscibility gaps were established. One two-phase region was stable below a transition temperature of about 315°C and extended from nB = 0.015 to 0.178. The other one extended from nB = 0.021 to 0.114 slightly above the transition temperature and had an apex at nB = 0.065 and 410°C. All phases involved have the fcc structure of pure palladium with lattice expansions proportional to their boron contents. The occurrence of miscibility gaps, i.e., the coexistence of dilute and concentrated phases, points to an energy of attraction between the dissolved particles, in the Pb-B system as well as in the Pd-H system. The filling up of the electron bands seems to be analogous, too, in the two systems, as indicated by the hydrogen absorption capacit15,17,18 and by the suscepti bility of Pd-B alloys.l8 In both types of experiments, boron acts as an electron donor. A chemical method was used to measure the activity of boron in palladium. Boron trioxide was reduced in a moist hydrogen stream: B2O3 + 3H2 = 2B + 3H3O [l] At known activities or partial pressures of boron trioxide, hydrogen, and water, the activity of boron could be calculated from the law of mass action. The equilibrium concentration of boron corresponding to this activity was determined as the weight gain of the sample. EXPERIMENTAL The samples consisted of small pieces of foil of 0.1 mm thickness and about 100 mg weight. The palladium was supplied by DEGUSSA, Germany, and stated to be

Jan 1, 1970

By J. H. Jensen

Bromine is the intermediate member of the halogen family of elements between iodine, a solid: and chlorine, a gas. The name is derived from the Greek "bromos," meaning stench. Bromine is the only nonmetallic element that is liquid at room temperatures with a melting point of -7.2" C and a boiling point of 58.78" C. Reddish brown in color, it dissolves easily in water to yield a red solution. Bromine volatilizes at ordinary temperatures to a red vapor that is very irritating to the eyes, nose, and throat. Density of the liquid is 3.12 and gas weighs 7.59 gpl at standard conditions. As the element is highly active, it exists in nature only as bromide compounds. Bromine was discovered by Antoine Jerome Balard in seawater bitterns in 1826 and first prepared in quantity in 1860. Distribution Bromine is widely distributed in nature and compounds occur in solution in natural brines, in seawater, saline lakes, oil and gas well brines, and in evaporite chloride minerals. The concentration of bromine salts ranges from 60- 65 ppm in seawater to several thousand ppm in oil well brines and saline lakes. The distribution of bromine in marine evaporite minerals and in the solutions from which they crystallized was determined many years ago by H. E. Boeke (1 908). Theoretical aspects regarding the geochemistry of bromine have been published in numerous papers (Raup and Mite, 1969). Bromine occurs in solid solution in carnallite and sylvite associated in potash de- posits; in halite in salt beds; salt in oil shales; and in trona deposits. Its presence is useful as a guide in geochemical exploration. The analysis of small amounts of bromides in the presence of large amounts of chlorides is discussed by W. Schwerdtner (1963). Manganese, iron, and iodine may interfere with the determination. Other analytical methods are discussed at length in the literature (Stenger and Atchison, 1964). Sources and Reserves The sources and reserves of bromine, given in [Table 1], appear ample to meet present and foreseeable requirements in all producing countries. With the occurrence of bromine salts in sea-water and other brines, the potential for bromine production is worldwide. It has been estimated that 99% of all commercially recoverable bromine is in the ocean. However, actual subterranean brines having a higher bromine content than seawater will continue to be the preferred sources of bromine for the foreseeable future. Markets and Prices About 17% (1968) of bromine produced is used in its elemental form, with the balance consumed as bromides and bromates. The largest use for bromine is ethylene dibromide which, together with tetraethyl lead, are used as an antiknock additive in gasoline. Tetra-ethyl lead is the antiknock agent. Ethylene dibromide combines with the lead after combustion in the engine to form a volatile com- pound that escapes from the engine with the exhaust gases.

Jan 1, 1975

The University of North Dakota, State Geological Survey, Grand Forks, N. D A G. Leonard, State Geologist. Two publications of the State Geological Survey are of interest Fourth Biennial Report, The clays and clay industries of North Dakota, and Bulletin 4, Lignite deposits and lignite industries of North Dakota. Bulletin 11 of the University is of interest: Geology and natural resources of North Dakota For further information, address the above

Jan 1, 1933

By Grimes, J. A.

EXTENSIVE discovery 'and rapid exploitation of orebodies within the past half century have attracted many able geologists to the mining industry and furnished them a wealth of data from which to develop theories concerning ore genesis. By tosting and elimillating theories which are not sufficiently sup- ported by fact, or which are based on inaccurate observation of field data, the trend of geological opinion has . moved strongly in certain directions until, at the present time, large numbers of geologists subscribe to a broad concept of .ore genesis that I would summarize as below:

Jan 1, 1928

By W. H. Andrews

THE constantly increasing consumption of Portland cement in the State makes the above subject of partlcular interest at this time. The increasing demand is due to the rapid settling of the country and the fact that new uses are being found frequently for the above named commercial article. The industry is one that is bound to grow as the population increases, and this being the case, it may be well ,it this time to consider briefly- the matter of the chemical and physical com-position of proper raw materials. A cement mixture is one that contains approximately 75 per cent. carbonate of lime, 15 per cent. Silica, and 5 to 7 per cent. alumina, and iron oxides; the other elements being magnesium carbonate and small quantities of the rarer elements general associated with limestone deposits. It call be readily seen from the above composition that it is possible to build up this mixture from a number of different materials. First.-A rock high in carbonate of lime can be mixed with clay or shale in such proportions as to bring about the desired composition ; the chief difficulty in the building up of such a mixture is that it is hard to find a clay or shale in which the silica-alumina, ratio lies .between 4 to 1 and 3 to 1 and at the same time shows physical characteristics which will make certain its adaptability to the practical manufacture of Portland cement. Very often clays or shales are found which are right chemically but contain large quantities of grit or free silica. Such clays or shale must be ground to extreme fineness in the mixture in order to make the silica and alumina combine with the lime when the mixture is burned. On the other hand, clays or shales are often found that have the proper physical characteristics but in which the amount of alumina, is too great.

Jan 9, 1913

By G. H. Kesler, C. E. Dryden, J. H. Oxley

Rates of heat- and mass-transfer from rods to recirculating air were determined within a one-quarter-scale model of a metals deposition bulb. The dependence of local and averaged rates of transfer upon outlet geometry, number of rods, position upon a rod, and airflow rate was established for flow patterns created by radial and tangential air inlets. The results are given a qualitative interpretation in terms of rates and distribution of metal deposition in a prototype deposition bulb. IT is well known that a number of metals can be prepared from volatile compounds containing them by causing dissociation of their compounds to occur at heated surfaces. Examples of such metals include silicon, titanium, zirconium, and aluminum, which can be prepared from their halides. While the ability to prepare high-purity metals by this technique is of importance in itself, the rate of deposition of metal also is important in considering the commercial potential of such a process. If the over-all process of deposition is broken down into separate steps of transport of materials to and from the heated deposition surface and establishment of chemical equilibrium at the surface, as was described in a recent paper,1 then since surface temperatures are usually high and surface equilibrium is attained very rapidly, the rate-controlling step can be considered as either that of transport of reactants to the surface or of transport of products other than deposited metal away from the surface. These two transport steps are related through the reaction stoichiometry. It can be shown1 that the rate and distribution of metal in such a transport-controlled process are determined by the over-all and local mass-transfer coefficients in conjunction with the equilibrium conversions at the hot surfaces. The rate relationship is: w = [KA(y a-y s)] B.E where the bracketed group is the rate of arrival of the reactant at the surface of area A as determined by the mole fraction driving force (y a - y s) and the convective transport constant K. The factor B is the weight fraction of metal in the reactant, and E is the equilibrium fractional conversion to metal. Numerical values of y, and y, are fixed by the vapor composition and the equilibrium compositim of reactant at the surface; and E can be determined by thermodynamic calculations or by experiment. However, values for the convective coefficient K are available generally only for systems of simple geometry, such as cross-flow past a rod or sphere or parallel flow past a flat plate or through a tube. Often it is necessary to work with systems of more complex geometry and in which the vapor flow may not be uniform or exactly parallel or perpendicular to the surface. It is possible, of course, to establish working correlations for these more complex systems by direct experiment; but the experiments usually are costly in both time and money. To circumvent this objection and to aid in arriving at an understanding of the relationships and interactions of the process variables, it is helpful to construct a model of the flow system in which air, water, or other convenient fluids can be substituted for the process vapors and with which mass-transfer measurements or analogous he at-transfer measurements can be made upon a simulated deposition surface. By this means, a large number of measurements can be made in a reasonable time, and the correlation of these results can be applied to the prototype system. Examples of the application of these techniques are to be found in the literature (e.g., Ref. 2). It is the purpose of this paper to illustrate these techniques by description of a model study which was done at Battelle Memorial Institute. The work to be described was of a preliminary nature; the investigation subsequently was extended to develop quantitative relationships among the significant dimensionless transport, geometric, and flow parameters. This more detailed study will be the subject of a future paper.

Jan 1, 1962

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 27 Montreal, Canada Sept, ?79 8 28 New York, N.Y. Feb, ?80 9 29 Lake Superior, Mich Aug, ?80 9 30 Philadelphia, Pa. Feb, 81 9 31 Staunton, Va May, 81 10

Jan 1, 1923

By D. F. Hewett

ALTHOUGH most persons will agree that an individual or a nation can profit from the experience of other individuals or nations, there is always room for debate over the degree of similarity of their past and present conditions and of their future problems. Noting the increasing interest that Americans are showing in our mineral problems, I have felt that we could profit from reviews of the experiences in mineral exploitation acquired by the industrial nations of Europe. Whether we can learn much from Europe's experience in exploiting such minerals as petroleum may be debatable, but certainly, with a record of metal production extending back nearly 3000 years, Europe should hold much of value for America. A trip to Europe in 1926 permitted me to visit 28 mining districts, of which about half are now or have been in times past outstanding sources of several metals. The districts range from England to Greece and from Spain to Poland. To summarize briefly my impressions of these mining districts, as well as such reactions to the thought and life of Europe as so short a visit permits, I shall only venture the opinion that Americans can review with great profit the ideas and actions of Europeans, with regard not only to the production of metals but to many expressions of life. I believe that America has made and is making new contributions to the art of living, as well as to the arts of mining and metallurgy, but in so far as Europe is and has been a laboratory of economic, social and political experiments, the results she has attained deserve the thoughtful attention of America. I have come to believe that many of the problems that harass Europe lie in our path not far ahead. I have therefore hoped that a review of metal production in Europe in the light of its geologic, economic and political background may serve to clear our vision with regard to our own metal production. One can not examine the literature of national metal production without being impressed that the countries of continental Europe, especially Germany and Austria, have shown greater interest and devoted more time to research into the record of metal production than Great

Jan 1, 1929

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 27 Montreal, Canada Sept, ?79 8 28 New York, N.Y. Feb, ?80 9 29 Lake Superior, Mich Aug, ?80 9 30 Philadelphia, Pa. Feb, 81 9

Jan 1, 1923

By Henry D. Hibbard

THIS article aims to clarify the use of some terms often occurring in writings on iron and -steel, and also to suggest several new short abbreviated names for some of the things related to the subject which now are indicated by phrases. Crude or Crude Iron The name crude or crude iron is recommended for the iron produced from ore by the blast furnace. When necessary it can be specified as pig iron when in the form of pigs (usually cold), or as molten iron, commonly called hot metal to distinguish it from cold iron in pigs. The product of a direct process of making wrought or malleable iron from ore is not included.

Jan 1, 1924

By J. F. Evers, S. Sadiq, F. W. Preston, G. W. Swift

Proper scaling of unsteady-state flow in laboratory gas reservoir models can be achieved if the permeability/fractional porosity ratio is less than 0.5 md. Porous media meeting this specification can be obtained from mixtures of sand and Portland cement provided (1) the water/cement ratio is in the range of 0.35 to 0.40, (2) the sand/cement ratio is in the range of 1/1 to 2/1, (3) the sand grain size is in the range of 48-100 to 18-28 mesh, (4) the mortar curing time is 7 days or more and (5) the cured mortar is dried under vacuum to reduce the temperature level employed during the drying process. The areal homogeneity of the mortars tested is reasonably good, although significant trends in vertical permeability were noted. The Klinkenberg and non-Darcy coefficients of mortar are such that proper scaling of these effects in the laboratory model could be expected. INTRODUCTION A long term deliverability prediction for a gas well is generally based on data determined from flow tests that are of short duration relative to the producing life of the well. These data, together with an estimate of gas reserves in place, form the basis for establishing the parameters of the mathematical model used to predict performance at future times. Results obtained from a mathematical model represent only an interpretation of the physical process being modeled. Experimental verification of the production process from discovery to abandonment is needed where production occurs under carefully controlled conditions. Ideally, one might consider such an experiment to be conducted in the field. Even if the cost of such an experiment could be justified, the time required would make it impractical to consider. However, if the time scaling problem could be handled properly, an experimental model of the gas reservoir production process could provide the necessary data to study the mechanisms of the production process in a reasonable time period. An experimental model has been designed and constructed using the data of this study as a basis. The model reservoir system consists of one producing well located at the center of a right-circular cylinder of porous material. Ten to 15 observation wells are located at strategic offset positions from the producing well. These wells, and the producing well, are fitted with pressure transducers so that the pressure-time history can be recorded at various radial and azimuthal positions in the drainage area during the entire production life of the system. Time is scaled in the model so that the time required to produce gas from discovery pressure to abandonment pressure is about 2 hours. This compares with a 20-year producing life in the model's field counterpart and gives a time scale factor of approximately 1:100,000. DESIGN CRITERIA To establish design criteria for the experimental model, the reservoir is considered to be a finite right-circular cylinder of radius rr, and height h with a producing well of radius rw located at the center and completed through the producing formation. This reservoir consists of a porous medium which has a uniform permeability k and gas porosity and the gas contained in the reservoir has density p, viscosity µ and molecular weight M. Initially, the pressure at all points within the reservoir is uniform at po. and the reservoir temperature is T. Since the reservoir production process has been demonstrated to occur in two distinct transient modes for either Darcy or non-Darcy flow,l it is

By W. F., Netzeband

SEVERAL criteria have been used more or less successfully in finding and developing orebodies in this district. Among them is the relation of the fracture to the orebodies. It has been known for some time that there was some relation, but it has been but recently. that careful study has been given to this subject. Like all the criteria used in this district, this relationship must be used with caution, for what-is true in one part of the district is not necessarily true in another.

Jan 1, 1928

By Robert McKay

THE practical study of corrosion requires consideration off its economic aspects. It must be based on sound scientific principles, but it should be borne in mind that probably the most important object of a corrosion test is to determine what metal in corrosion-resisting construction will produce the greatest operating profit. Thus the corrosion test must be directly connected with money values or it is not a practical corrosion test. This, perhaps unusual, connection between corrosion and economics is partially due to the fact that corrosion deals only with the time factor or duration of equipment, and it is almost the only test which deals with this feature. In these statements a departure is made from the academic definition of the word corrosion and it is done deliberately. The use of the term corrosion is unusual. It is as though we spoke of a tensile test as. a "breaking" test. We are not interested primarily in the break but in the strength of the metal. There is no English word which expresses our main interest in corrosion-testing, but let us have clearly in mind that we make corrosion tests to prevent corrosion. Our real interest is in this corrosion-prevention, not in the corrosion. Previous to 1922, it was common comment that "it is impossible to determine the course of corrosion by laboratory testing." This statement was true at that time in that the technique of laboratory testing for corrosion resistance was so vague that tests in the laboratory gave untrue results almost as often as true ones. This was so, even in the simple case of determining which one of two metals better resists a given solution. While this is no longer true the number of misleading "corrosion tests" still being ground out by laboratories is too large in the light of our present knowledge. There are two important features of corrosion testing whose neglect is a large contributing factor to misleading results: (1) The economic relations of the corrosion tests to other tests; (2) testing technique.

Jan 1, 1929

By Paul Hunt

UP to June, 1923, the Park-Utah mine had shipped about 94,000 tons of a direet-smelting ore of a gross value of $4,200,000, or about $45. a ton. These values were in gold and silver only, although the ore carried small amounts of lead, copper and zinc. Freight, treatment and deductions had averaged $15.40 a ton. At the expiration of the Pittman Silver Act there was in sight about 30,000 tons of a similar ore with a gross value of about $15 a ton in gold and silver, and a large body of partly developed lead-zinc ore of a gross value of about $20 a ton, 40 per cent. of which was represented by the lead-zinc content and the balance by the silver and gold. Mine costs had been high during the life of the Pittman Act, but as a large part of the profits had gone into equipment of the mine and the orebodies were large and had good walls, we knew that mine costs could be greatly reduced. We were therefore faced by the necessity of getting lower freight and smelter rates or of concentrating the ore. We did obtain better freight rates on lower grade ore, and a favorable smelting rate on the small tonnage of siliccous silver-gold ore, but this smelter rate could not be applied to the lead-zinc ore with any profit to ourselves. The Judge mill of the Park City Mining & Smelting Co., with which we were affiliated, was running to capacity; if we built our own mill it ineant a 5-mile freight haul to a satisfactory millsite and a year's delay. Fortunately, the International Sillelting Co. had just inherited a mill at Tooele which, with some changes, was about double the catpscity required for its own ores. Flotation tests were run on Park-Utah ore and a contract entered into with a low base treatment charge per ton, the tariff being largely fixed by the metallurgical deductions. This contract has been admirably calculated so that the miner can follow a lean orenbody to its limit. Such a procedure has no doubt made it difficult for the smelting company at times, but it has resulted in finding ore extensions that otherwise might have been missed, so In the long run it has profited too. A flat rate per ton would have been like mining up to the claim endlines in a great many of the stopes. In order to offer such a contract it can be inferred that the smelting company must have been able to make high reeoveries and high-grade products on a very lean ore.

Jan 1, 1928

By J. B. Cheatham, R. B. Paslay

Rock stresses and steady-state flow rates induced by the pressure gradient associated with the flow of formation fluid into a borehole have been analytically determined for a permeable, elastic material saturated with an incompressible fluid. In this analysis, the material properties and loading are considered to be symmetric about the axis of the borehole and independent of axial position. For Case I the material is assumed to have uniform permeability in the radial direction, whereas for Case 11 the permeability is assumed to have been reduced in a localized region adjacent to the hole by either normal well completion and production operations or deliberate plugging during air drilling. Results of a numerical example indicate that, in the absence of plugging, the rock shear strength must be approximately two-thirds the formation fluid pressure in order to prevent rock failure. The required rock strength is high for small radial zones of plugging and decreases as the region of reduced permeability becomes larger; however, a depth of plugging can be reached beyond which there is no real gain in strength, although the flow rate can be further reduced. INTRODUCTION During normal production of oil from a well, it is often desirable to increase the production rate of the formation fluid by increasing the pressure gradient through the formation adjacent to the borehole. Depending upon the magnitude of this pressure gradient and strength of the rock material, this production-rate increase can cause sloughing of the hole wall. In many cases, the production - rate increase can result in excessive sand production, increased wear of production equipment, lost production time and expensive workover jobs. In addition, the phenomenon of increased rock bit penetration rate with the use of a gaseous instead of a liquid drilling fluid has been observed in oilfield drilling operations and experimentally demonstrated by various investigators for several years. The improvement obtained by employing this technique can be quite significant and offers apromising method for reducing drilling costs. However, air drilling is currently limited to geographical locations where high-capacity water-bearing formations are not encountered. This limitation has prevented widespread adoption of air-drilling techniques, because the water influx into the borehole interferes with efficient removal of the drilling cuttings and usually results in a condition such that the bit becomes "balled-up" or stuck in the hole. In an attempt to remove the water - intrusion limitation from air drilling, various chemical and mechanical water shut-off methods have been proposed. Goodwin and Teplitzl suggested one such proposal whereby the permeability of the water-bearing rock structure was reduced in the vicinity of the borehole. Although the development of a shut-off method based upon this approach would certainly be welcomed by the oil industry, it is conceivable that, under certain conditions of the pressure gradient, strength of the rock material and depth of the modified permeability zone, a stress field can be created that will result in an unstable hole. As part of their study, an analytical solution is given for stresses in an idealized model of a hole and the surrounding rock material. The purpose of the present study is to extend the analysis of Goodwin and Teplitz to gain more insight into the details and consequences of excessive production rates and formation water shut-off. In particular, simplified models of these problems have been analytically examined, which makes possible the evaluation of the type of stress fields that can be anticipated as a result of these production and drilling practices. Both problems solved concern the determination of the steady-state volume flow rate of the formation fluid and the resulting steady-state stress and displacement distribution in a hollow, cylindrical configuration. The cylinder of Case I, corresponding to the production-rate problem, consists of a material with a constant permeability from the inside surface to the outside surface; the cylinder of Case 11, corresponding to the water shut-off problem, consists of a material with a constant permeability from the inside surface to an intermediate concentric cylindrical surface and a second constant permeability from the intermediate surface to the outside surface-