Search Documents

By White L. R, Boger D. V

The paper describes the surface chemistry and particle physics that control the fundamental flow properties (Theology) of mineral particle slurries. We further address, through a series of case studies, the design data that emerges from experimental studies of the flow properties of complex, high volume fraction mineral slurries. The case studies are drawn from mineral oxide concentrate processes, tailings dewatering operations and from filter cake production and management. The paper emphasises the essential links between design of process slurry handling systems and the control of the flow of such slurries by control of the pulp chemistry.

Jan 1, 1992

By Aguirre E, Chitombo G

The magnitude of stress variations associated with a blast wave near production pillars is analysed by modelling blast vibrations measured in the surrounding rockmass. The results indicate a wide variation in stress which is thought to contribute to the observed damage in pillars adjacent to the draw points.

Jan 1, 1995

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal.

Jan 1, 1989

Mount Isa Mines Limited has been mining copper ore for 50 years. In recent years, this production has been entirely by open stoping methods with cemented backfill, mostly in the large 1100 orebody.This has been the major ore source for 20 years, with smaller amounts coming from the 400, 500, 650 and 1900 orebodies. At present, the 1100 orebody is the only source, and this situation will continue until the deep 3000 and 3500 orebodies begin producing in late 1992/93. Production rates have increased to almost 6 Mt/yr, and are planned to rise to 7 Mt/yr by 1995/96. In the future, there will be a move towards variations of the open stoping system as production moves to more lensy zones of the southern 1100 orebody and to the deeper 3000 and 3500 orebodies. This paper describes current operations in the 1100 Orebody, with some indications of future directions.

Jan 1, 1993

By J Hadjigeorgiou, T R. Stacey

A ground support system is a combination of individual reinforcement and surface support elements that work together to retain and contain the rock mass. The various elements are subjected to external loads and to interactive loading between individual ground support system components. This paper focuses on the challenges in determining the capacity and behaviour of mesh, recognizing that installed mesh can be subjected to several loading mechanisms. Field observations from underground hard rock mines demonstrate that there are multiple types of damage and modes of failure of mesh. However, these are difficult to reproduce in a laboratory environment. A critical review has shown that existing mesh laboratory testing rigs reproduce very limited loading conditions that may not be representative of underground conditions. This has significant implications in quantifying and extrapolating the performance of mesh to ground conditions. CITATION:Hadjigeorgiou, J and Stacey, T R, 2018. Challenges in determining the capacity of mesh, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 280–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Smith P

The past 20 years have seen the replacement of hydraulic control of longwall mining systems by the neater. smaller and better controlled electronic units.Early problems of moisture and other effects on reliability were overcome to see electronically controlled supports chosen for Corrimal Colliery ten years ago. Lessons from Corrimal and elsewhere, with following improvements and sophistication led to wider use as exemplified by Meco and other electronically controlled supports used in more recent installations in New South Wales, Queensland, USA and Czechoslovakia of the total of over 80 electronically controlled support installations worldwide in the past decade. Present work is toward a fully "integrated face" of British Coal by 1993, incorporating the Meco automatic face straightening system already due for practical use in the UK later this year. However the manless face still appears to be some way off although the present minimum crews and close monitoring, including early warning, are promising stages.

Jan 1, 1991

By C J. Larder, S E. Turner

The concept of underground grinding is not new, but to a metallurgist and a mining engineer this could be considered unconventional. The idea of pumping a ground slurry several hundred metres from underground in a single lift could also be considered to present a daunting engineering challenge. Using a practical example of a mine in Australia where the owners have requested not to be identified, this paper challenges the conventional thoughts on these concepts and shows that with basic sound engineering practices the production of a ground slurry from underground could potentially provide significant operating cost savings. The supply of ore from the underground mine is currently drawn from depths approaching 800 m below the surface. The cost of hauling the ore to the existing underground crushing station located 500 m below surface has been steadily increasing. A number of alternatives to reduce the mining and processing unit operating costs were examined by Sinclair Knight Merz (SKM) and the mining company. The most radical of these is the use of hydraulic hoisting of ore at an increased production rate. Numerous questions were asked, such as: How does one get a SAG mill or an HPGR crusher underground? Where does one locate a grinding mill underground? Does the technology exist to pump the slurry to surface in a single lift? What will be the cost benefits? What are the risks involved? The study covered the two main technical issues underlying the potential benefits. Firstly, technical evaluations were undertaken on the pumping technology currently available for single and multiple lifts to surface. Secondly, the issues relating to the feasibility of delivering and locating a SAG mill underground were reviewed. Although the capital costs for this project are significant, the operating cost savings showed a potential payback period of less than two years, and furthermore provide the basis for an increased mine life, especially at lower metal prices.

Jan 1, 2005

The importance of the minerals industry to Australia is briefly reviewed and the professional specialists essential for the industry identified. The average first degree graduation numbers in geoscience, mining engineering, metallurgy/materials and chemical engineering are shown and compared with the postgraduate numbers. Demographic trends in population are reviewed and the implications for the required numbers of trained specialists indicated. Short/medium and long-term possible solutions to potential shortages of trained personnel are canvassed.

Jan 1, 1997

By Hunefeld R

In the field of mining engineering, design and planning are complex tasks, which require the knowledge of various engineering disciplines. GRUBE (Graphisch-RechnerUnterstiitzter BergwerksEntwurf) is a modular databased program system, which offers computer aid for all mining departments using a 3D CAD software as the user interface. Despite the data quantity and complexity, specific and uniform working conditions have to be applied to the planning of technical equipment of a pit. With the application of 3D graphics, complex data stores and their interrelations become 'palpable' for the user by suitable visualisation. GRUBE-M forms the mechanical operations module of GRUBE, in which underground locations displayed as three-dimensional graphic models are `equipped' interactively. Planning alternatives can be created and compared quickly in terms of technical calculations and economical analysis.

Jan 1, 1995

By Baohm C, Barker T

There have been significant changes in the Australian mineral sands industry in recent years due to changing supply and demand conditions, new product opportunities and opportunities for rationalisation of operations. Earnings within the industry have typically been volatile and this has been reflected in the share prices of listed mineral sands companies. Apart from the effects of variations in the state of the economy on the industry, share prices have also reflected the extent to which a company's earnings volatility is due to capital structure, the relative proportion of fixed costs to total costs and the nature of th'- sales mechanism. At the time of writing, the high prevailing share prices for industry participants and the current outlook for the industry would suggest that the time is opportune for raising equity capital. The immediate outlook for the industry and its various product segments appears favourable but beyond this the usual uncertainties remain. The new tax environment will cause most companies in the industry to have to rethink their dividend and capital structure policies. Most shareholders will now be concerned to maximize dividend receipts and minimise exposure to capital gains tax. Companies in the industry that have relied fairly strongly on earnings retention to help finance growth in the past will- need to look to increased equity raisings in the Future.

Jan 1, 1986

It is very rare in the underground hard rock environment to find a deposit that is ideally suited to a specific mining method. Usually the irregular shape of the orebody will allow the deposit to be extracted by more than one mining method. During the prefeasibility stage, a number of conceptual mine designs are generally evaluated to see which offers the best method of extraction for the deposit. The selected method is usually based on key decision criteria such as the overall extraction of the orebody, the amount of metal produced annually and the unit cost of production. Often the prefeasibility study document will state that the project has an NPV of æxÆ million dollars. This statement can be made without any quantitative consideration of the likely risks of the mining methods reviewed or the level of confidence in the estimation of the NPV. By assigning a probability of failure to each component of the mining cycle a measure of the risk for each method can be determined. One mining method may provide the highest NPV when it is performing well, however, there may be a higher risk of a major failure impacting on the performance of that method, eg the failure of a mass blast of a crown or rib pillar. This paper will present a flowsheet approach to the use of risk analysis for determining the likely production rates of different mining methods. This framework allows the annual metal output to be estimated and from this the NPV for each method. A level of confidence can be applied to the estimated NPV for each option. An example will be presented on how this technique has been used within the Normandy Group.

Jan 1, 1998

By Warner R. E

Present capacity for molten iron production at Port Kembla is an average of 13 000 t/day from five blast furnaces. The most recently installed blast furnace, No.5, was commissioned in March 1972 with a design capacity of 4 500 t/day. For the first reline currently scheduled for 1977, plans are being finalized.for significant modifications and uprating of capacity. Achievement of the initial design capacity from No.5 blast furnace on a sustained basis was not realised until the third year of operation. Although the furnace is only 42% larger than No.4 blast furnace on an inner volume basis, the more stringent raw materials, operation and maintenance requirements of the larger furnace and more complex equipment have been found to be much more critical than anticipated in the planning stages. These problems have also been experienced by many other companies who have recently installed large new blast furnaces. Some of the principal problem areas are described together with measures taken to over- come the difficulties. The problem areas include the failure of'the shower cooled bosh, failure of the upper shaft brickwork, sludge

Jan 1, 1976

By Nilmani M, Fountain CR

Injection of gases into slag-melt mixtures produces various zones as a result of bubble formation and disintegration within the melt. The extent of these zones depends on the type of reactor used. When compared with ferrous processes, non ferrous processes are character- ised by large bubbles formed adjacent to the tuyeres, low flowrates and shallow tuyere sub- mergence. These features can result in a greater proportion of reaction occurring above the bath, more refractory wear and tuyere blockage with more splashing. The large bubble zone adjacent to the tuyeres has been investigated using the tech- niques of physical modelling, mathematical modelling and plant trials. Large bubble form- ation in physical models was recorded using a high speed camera and a rapid response pressure transducer coupled to an oscilloscope and data recorder. It was found that the bubble volume (Vb) could be correlated at low flowrates using the single bubble model Vb = 1.378 Q6/5 g-3/5 Deviations from this correlation occurred with increasing gas jet momentum. Plant trials were carried out on a copper converter at Mount Isa Mines during five different charges. Pressure measurements were made through the tuyeres during the slag blow and commencement of the copper blow. The power spectrum density showed that the dominant pulse amplitude occurred at a frequency of approximately 3 pulses/sec. Plant data from this and other converters were correlated using the same relationship as for physical modelling. De- viations occurred due to the state of the re- fractory, bath composition or bath circulation effects.

Jan 1, 1984

By A Whaanga

The use of photogrammetry has greatly increased the accuracy of 3D mapping underground. However, this has not reduced the need or desire for geologists to produce plans and sections showing an interpretation of the mapped geology. At the Waihi Underground Gold Mine, a hybrid solution has been developed that utilises the accuracy of photogrammetry and mapping onto face photos with the CAD-based Deswik.MappingTM functions to create plan and section maps. These have the benefit of looking like traditional paper maps but are more spatially accurate and richly attributed with metadata that can be filtered and exported to downstream processes. Deswik.MappingTM is a tablet-based solution that allows the geologist to map digitally with a stylus. Automation is utilised for the updating of survey as-builts, approved designs, drill holes, geological mapping, vein interpretations and mine work areas, reducing the requirement to print out maps at various locations and scales. Having 3D mine software on a tablet device provides a wealth of features not available when using paper: scaling is a problem of the past; information can be turned on and off; features can be viewed in 3D; and measurements between points of interest can be calculated in 3D space, for example, between vein wireframes and drill hole sample information. A suite of custom scripts has been developed that take the spatially accurate, registered and attributed polyline data from photogrammetry scans and converts them to a geological mapping legend with vein textures, structural information, and lithological boundaries. These 3D maps can be plotted in plan or section view and satisfy the requirements of the most ardent paper map supporter.

Mar 22, 2022

The mIning operations of Bougainville Copper Pty. Limited are located at Panguna on the Island of Bougainville which is part of the Territory of Papua and New Guinea.C.R.A. Exploration Pty. Limited first established mineralization in the Panguna area in 1964. Exploration work since then has established ore reserves estimated to be 900,000,000 long tons of ore assaying 0·48 per cent copper and 0·36 dwt/ton gold. An economic feasibility study completed in July, 1969 enabled a decision to be made to proceed with a major mining operation. The ore will be mined by open cut methods and will be treated in a conventional concentrator with a nominal capacity of 90,000 short tons/day. The concentrate will be pnmped as a slurry through a 16 mile long pipeline to a port established on the east coast where it will be filtered and dried ready for export. Other supporting facilities for the mine include two towns, a 135 MW steam power station, and access roads.

Jan 1, 1971

By N Strong

Cracow is a high-grade; low-tonnage underground gold mine located approximately 500 km north-west of Brisbane in Central Queensland. It is a steeply dipping, narrow vein, epithermal gold and silver deposit that is accessed via a decline from surface. Cracow is owned by joint venture between Newcrest Mining (70 per cent) and Sedimentary Holdings (30 per cent). The orebodies are 5 m wide on average and the ore is extracted via sublevel open bench stoping. Stopes are extracted to a strike of approximately 25 m before being backfilled with waste. Prior to the introduction of electronics, the mine would remove a small amount of the previous backfill out to create a void, and then begin blasting two to three rings at a time, with the ore being extracted between each blast. This method caused the ore to be blasted onto the waste backfill resulting in dilution of the high-grade ore. It also meant that the extraction of each stope took a number of weeks and numerous blasting events. In the fourth quarter of 2005, the mine struck a geotechnically sensitive stope, where all 20 rings had to be extracted in a single shot or risk possible geotechnical problems that could sterilise the ore. Due to the limitations of NONEL« delay detonators the mine could not fire all the rings in a single shot and needed to use an electronic detonator system to extract the stope. Some unexpected benefits to the mine were increased fragmentation, reduced vibrations, reduced dilution, improved efficiency and improved hanging wall and footwall conditions. After the success of this first electronic shot, the mine has since moved to firing all their stopes with electronic detonators. With electronics the mine has been able to fire much larger blasts, and has in fact moved to firing their blasts in the opposite direction, firing towards the draw point instead of into the waste backfill, thus reducing ore dilution.

Jan 1, 2008

In order to meet the increasing demand for coal for their Newcastle Steel Works, the Broken Hill Pty. Co. Ltd., on June 5, 1937, approved of a scheme to sink a tunnel to the Victoria Seam at their Burwood Colliery. This seam was virgin at this locality and lay nominally horizontal at a depth of 320ft. vertical from the surface.For the purpose of despatch of the coal produced it was decided that the tunnel be equipped with a rubber belt conveyor system.This was a comparatively new departure in Australia, and, indeed, was one of the first installations of its kind in the world, designed to raise coal from considerable depth by this means. Later the tunnel was extended to the Borehole Seam, which lay nominally horizontal at a vertical depth of 600ft. from the surface. The whole installation is the subject of this paper.In planning a project of this kind, consideration had to be given to the following:-1. Location of tunnel with regard to existing surface railway sidings and shafts.2. Ultimate tonnage required.3. Width and construction of belt.4. Speed of belt.5. Inclination of belts.6. Number of belts and design of equipment.7. Cross-sectional area of tunnel.8. Inclination of tunnel.9. Surface drainage.10. Type of equipment for drifting the tunnel.11. Method of ventilating the tunnel during sinking.After the general layout and design of the scheme had been prepared it was decided that tunnel drifting would begin immediately and that the belt installation, together with the feeder plant, would be detailed and manufactured by the time the drift...

Jan 1, 1947

By M A. Noppé

"Investors and other stakeholders assessing the risk, opportunity and relative value associated with a resource project need to appreciate the project in its correct context. Errors, omissions, biased reporting or conflicting information in project reporting may lead to a misinterpretation of technical and financial results, resulting in biased estimates or assumptions on project value.This paper provides a simple ‘Resource Project Framework’ for presenting a project’s status that may be readily benchmarked against other similar projects and to illustrate the stages required to advance the project outcomes to higher levels of certainty. The framework draws on definitions and guidelines readily available in various resource industry reporting codes and public company reporting requirements.The framework assesses three key areas for placing a resource project in its correct relative context, namely:the project development stagethe confidence in the Exploration Results, Mineral Resources and/or Ore Reservesthe level of accuracy, precision and confidence in the technical and economic studies supporting the reported results or options for the project.The application of the Resource Project Framework is illustrated using two project examples, one from publicly reported company project releases and the other for two development projects.CITATION:Noppé, M A, 2016. A framework for presenting and benchmarking resource projects, in Proceedings Project Evaluation 2016, pp 260–274 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By C E. Loo

The cohesive zone has a significant influence on blast furnace operation and performance. The high-temperature behaviour of the reducing ferrous burden determines the properties of the cohesive zone and is studied in a laboratory using a softening and melting test. This paper summarises recent work aimed at better understanding the physico-chemical changes in a ferrous bed during softening and melting. Using a combination of standard, non-standard and quenched tests supported by optical image analysis, this work has highlighted some important differences in behaviour between lump, pellets and sinter as well as between the two lump ores and two acid pellets. As with the two lump ores, one pellet is denser than the other and the denser ore/pellet is also higher in silica.Within the cohesive zone, densification of the ferrous layer leads to reduced permeability and greater pressure drop. From the work presented in this paper, two key mechanisms of ferrous layer densification were identified. Firstly, the formation of fayalite, which melts at low temperatures, can act as a lubricant between particles and lead to densification of the ferrous layer under load. Secondly, reduction to metallic iron is topochemical and fayalite in the outer shell of the particle restricts gas flow to the centre and results in the formation of a wustite core. As temperatures rise, the wustite melts and eventually exudes out of the shell, occupying void spaces between particles and further reducing layer voidage and permeability.This work has shown that density and silica content are two key factors that result in increased densification of the ferrous layer. For porous Australian lump ore, the higher porosity and lower silica reduces the formation of fayalite and limits the formation of the wustite core, ultimately leading to a more permeable bed. The difference between the porous and dense ores was more pronounced with the introduction of prereduction to better simulate blast furnace conditions. This suggests that a porous ore gives significantly better cohesive zone permeability and blast furnace operations than a dense ore.The behaviour of fluxed sinter particles is different in that the silica reacts with lime to form dicalcium silicate. Minimal wustite core forms because relict hematite particles in sinter are only small and reduction occurs uniformly throughout the particle. Even with significant loss of material through prereduction, beds formed from sinter remained comparatively rigid. Studies using a typical blast furnace burden mix of 80 per cent fluxed sinter and 20 per cent porous ore showed that the structures of these beds at softening and melting temperatures are very similar to the sinter-only test. Measurements of bed contraction and pressure drop also confirmed that the introduction of 20 per cent porous ore into a sinter bed did not alter its properties. This is an indication that 20 per cent ore can be easily accommodated by blast furnace burdens.CITATION:Loo, C E, 2015. Important acid ferrous burden properties in the cohesive zone of a blast furnace, in Proceedings Iron Ore 2015, pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

The beneficiation of heavy metal oxides, such as iron ore, is usually performed with heavy medium separation in cyclones, static baths and lately with Larcodems. Atomized ferrosilicon is most suitable as a heavy medium at densities above 3600 kg/m3 whereas a mixture of milled and atomized ferrosilicon is suitable at densities below 3600 kg/m3. When operating a beneficiation plant at densities higher than 3600 kg/m3 the quality of the ferrosilicon particles is an important factor that influences the control of the beneficiation process. Therefore, it is important to know how the rheology would be affected by the ferrosilicon quality as it also influences the control of the process at these elevated densities.

Jan 1, 2002