Search Documents

By H. Lagendijk, I. J. Reinecke

Mintek was contracted by Oriel Resources plc in 2004 to conduct a preliminary assessment study on smelting ferronickel from the large but relatively low grade Shevchenko nickel ore deposit in Kazakhstan. A detailed feasibility study (?DFS?) was awarded to Bateman BV following promising results from the preliminary assessment study (?PAS?) and small-scale pilot plant test work. As part of the DFS, a total of 450metric tons of ore was collected from three different locations in the deposit and shipped to Mintek. After sampling, the bulk sample was prepared for smelting. This comprised crushing, screening and calcining with each step done separately for the three different lots. The chemical composition of the ore from the deposit is relatively high in silica and therefore falls out of the MgO to SiO2 range that is normally processed by pyrometallurgical means to produce ferronickel. The main objective of the testwork was to demonstrate that a method could be found and successfully applied to smelt these siliceous ores and produce an acceptable nickel-containing alloy. A 2-m ID DC arc furnace was installed with a twin-cathode (electrode) configuration to replicate the proposed commercial-scale furnace and also incorporated an advanced design of water-cooled copper panels in the lower furnace sidewalls to withstand the aggressive nature of the high SiO2-containing slags. The reductant used was a high-volatile coal from Karaganda in Kazakhstan. The reductant addition was adjusted to achieve a 90% recovery of nickel. In the assessment of the process metallurgy, some deviation from equilibrium conditions was observed. This deviation is ascribed to the intermittent existence of a smelting bath partially covered with feed during the testwork. Optimization of smelting conditions should result in the metallurgy (slag metal equilibrium) being closer to the theoretical predictions and make the production of a 20% nickel alloy possible at 90% nickel recovery. The solution for the successful processing of these siliceous ores was found in the attainment of the necessary operational stability through the control of arc length, operating temperature, open-bath smelting conditions and flux additions of up to 10% dolime for the most siliceous of the three ore types. The test work carried out by Mintek provided the basis for the process flow sheet and engineering design of the DC arc smelting furnaces for the Shevchenko Nickel project.

Jan 1, 2007

Prediction of fragmentation by blasting is most commonly based on theassumption that a single distribution of pre-existing discontinuities is present within a blasted rock volume and that the underlying mechanism of failure is tensile failure. It is assumed that the tensile stress field created by a blast initiates and extends radial cracks around the blastholes. Interaction between radial cracks from different blastholes and the free surface creates rock fragments. In reality, fragmentation of the rock occurs due to two mechanisms.One is related to the compressive-shear failure of the rock (mainly rock matrix) close to the blastholes, while the second mechanism is the previously mentioned tensile failure of the rock mass. The secondmechanism of failure occurs in the form of extension of the larger cracks in the region beyond the crushed rock, and this type of fragmentation occurs after the crushing phase. In the case of hard rock or blasting where the extent of crushing is minimal, the currently used prediction methods give a reasonably good result. However, there are many blasting conditions where the amount of rock crushing is significant. In the case where fragmentation of the given rock volume occurs dueto two different mechanisms, modeling of the rock fragmentation with a single distribution function is not appropriate. To model the fragment size distribution generated by two different mechanisms, it is necessary to use a two-component fragment size distribution function and a scaling parameter that will determine the proportion of the fragmented volume created by each mechanism. The purpose of this paper is to present results of blast fragmentation modeling based on two mechanisms of failure. The two-component model (TCM) utilises experimentally determined parameters from small scale blasting and parameters of the Kuz-Ram model, for more accurate prediction of the complete rock fragment size distribution curve. The methodology is such that it is possible to predict complete fragment size distribution, including fines, of ROM product for a future mine, at the feasibility phase of mine design.

Jan 1, 1999

By A. Deneys

An experimental technique has been devised for studying the reaction kinetics of the reaction: ZnO + 2Fe0 = Zn(g) + Fe203, by which zinc evolution can occur from a molten slag bath in the absence of a carbonaceous reductant. When studying the reaction kinetics by heating from room temperature, solid state reactions and poorly defined melting points may obscure the starting point of the reaction. In order to eliminate this problem, an experimental technique was devised whereby two molten slags could be melted independently, and then mixed, to provide a well defined starting point from which to begin taking measurements. Two crucibles were mounted in a vertical reaction cylinder. The upper, mild steel, crucible had a bottom pouring plug which was sealed by a steel stopper rod. A fayalite mixture was contained in this crucible. The lower crucible contained an A12O3-CaO-SiO2-ZnO solution. Once the two slags had been melted, the steel stopper rod was removed from the upper crucible. The upper, reduced slag (fayalite in equilibrium with the upper steel crucible), drained into the lower crucible where the two slags were mixed by submerged argon stirring. Dip samples were taken to measure the zinc content of the final mixture as a function of time. The experimental procedure will be described, as well as results of experiments which were conducted on synthetic slags. The system investigated was similar to the lead blast furnace slag which is produced by the primary lead smelters of Missouri, USA.

Jan 1, 1997

By Emilie S. Williams

The Doyon Mine?s Zone 1 (Altered Zone), found along the southern boundary of the mine, encompasses approximately 20% of the mining reserves. The mineralisation is found in a series of steeply dipping narrow veinlets, which are contained in an extremely weak host rock: a sericitic schist with RQD values ranging from 0 to 20. Longhole mining methods are used, with either longitudinal or transverse approaches, depending on the width of the ore zone. Dilution is of critical importance in the mining of this zone, particularly in longitudinal stopes, where dilution levels have averaged 55% since 2000. Major factors influencing dilution in this zone include the stope geometry and standup time. A two-phase approach has been developed to mine and backfill longitudinal stopes: the top of the stope is pastefilled after approximately half of the broken ore has been extracted; the remainder of the ore is extracted once the plug has cured; and the remaining void is filled. This method has been used in six stopes to date, resulting in an average dilution of 17%. This paper details the application of this technique and its effect on dilution.

Oct 1, 2004

By W. Song, C. Richards, B. Q. Li

"This paper presents a two-phase flow numerical model for spouting gas-particle flow reactors used in chemical vapor deposition processes for manufacturing heart valves and other biomedical implants. The model is developed based on the Eulerian-Eulerian formulation of gas-particle flows, with the k-e engineering model modified with the presence of particles for the description of turbulent gas flows. In parallel with the numerical model development, physical models are set up, where the particle image velocimetry is used for visualizing the particle flows and spout shapes and heights and optical probes are used to measure the particle velocities. The numerical model predictions are compared reasonably well with the experimental measurements.IntroductionVarious biomedical implant components, such as bone joints, dental components and heart valves, are coated with bio-compatible thin films by chemical vapor deposition in particle-laden chemical reactors [l-5]. In these reactors fine particles are used as packing and supporting media. During the coating operation, these packed particles are fluidized by an upward gas jet from the nozzle, reach a certain height and fall back on the top of an annulus region. These recirculating particles are mainly for levitating the implant components (usually one or two in a reactor at one time) so that every portion of them is equally exposed to the gaseous atmosphere. An equal exposure is critical for forming a uniform, mechanically strong and corrosion-resistant coating on implants. Plant experience shows that the quality of the coating is directly related to a stream of operating parameters such as temperature, particle size and loading, and gas flow rates [6]. Optimization of these operating parameters for improved reactor performance depends crucially upon our fundamental understanding of the physics governing the gas-particle flow, heat, and mass transfer phenomena taking place in these reactors."

Jan 1, 2004

By R. H. Nafziger

A novel process has been developed for preparing directly workable steel ingots from prereduced iron ore pellets by a two-stage process. The pellets are continuously charged into an electric arc furnace, where molten metal is separated from the gangue. The molten metal flows out of this furnace through a hollow nonconsumable graphite electrode immersed in a molten flux in an electroslag furnace. The molten metal solidifies on a continuously withdrawing base plate to form the ingot. A variety of standard carbon and alloy steel ingots . free of porosity , were produced using suitable decarburizers and ferroalloy additions. Some advantages of the two-stage process include: (a) consumable electrode fabrication is eliminated; (b ) no expensive deoxidizers are required; (c ) the uncontaminated electros lap flux can be reused; (d) energy consumption averages 25% less than in a conventional electric arc - electroslag operation ; and (e) the operation is continuous.

Jan 1, 1977

By Alireza Kamrani, Yashar Pourrahimian, Hooman Askari-Nasab

In-pit crushing and conveying (IPCC) is an option to decrease the enormous operating costs that a truck shovel can introduce in an open-pit mine. Finding the best locations for the IPCC over the mine life will impose a new set of requirements for the mine planning. Through a two-step mathematical programming model alongside the road network, this method finds the optimal in-pit crusher locations and relocation times first and then optimizes the long-term mine schedule. The model is verified by a real mine. The results show that the truck travel time could be reduced by 500% and the discounted cash flow increased by 8% with an optimized schedule considering the crusher placement.

Jun 25, 2023

By HaiWen Luo, Bin Hu

A ultra-high strength medium Mn steel with good ductility was designed and manufactured via the combination of warm rolling and V alloying, which produced not only the extensive precipitation of fine VC particles in both ferrite and austenite but also the bimodal size distribution of retained austenite (RA) grains. A substantial increase of yield strength up to 650 MPa was achieved due to the addition of V without deteriorating ductility. The coarse RA grains firstly transformed to martensite during yielding at the much higher stress threshold, followed by a significant work hardening due to dislocations multiplication, twinning-induced-plasticity (TWIP) and transformation-induced-plasticity (TRIP) in the ultrafine RA grains. The best combination of strength and ductility included 1.5 GPa ultimate tensile strength and 28% total elongation. This was achieved due to the sustainable TRIP and TWIP effects in the later straining stage resulting from the ultrafine austenite grains, the latter were reversely transformed from the recrystallized ferrite grains.

Oct 1, 2019

By P. T. Nguyen

The analysis of particle capture by an air bubble by two separate phenomena of collision and attachment has been difficult due to the uncertainty in determining when and where the two phenomena begin and terminate at the bubble surface, respectively. Therefore, a unified analysis was developed by solving the motion equation for the particle capture as one process. No distinction be-tween collision and attachment was made. Both the liquid film described by the micro-hydrodynamic resistance functions and the surface forces were included in the new model. The model predictions with the DLVO (Derjaguin-Landau-Verwey-Overbeek) surface forces did not agree with the experimental trajectories of latex and silica spheres. The model predictions with the inclusion of the non-DLVO attractive surface force agreed with the experimental data. The non-DLVO force reduced the repulsion between the non-attaching particle and the bubble, and significantly increased the attraction between the attaching particle and the bubble. The unified analysis is capable of predicting particle capture without the use of the induction time. The unified analysis also shows significant influence of the short-range hydrodynamic interactions on the collision which has been previously ignored.

Jan 1, 2014

By G. V. Krishnan, L. Adler

A rock classification for drilling and boring is presented covering most equipment types and providing an estimation of the key parameters for operation, such as thrust and speed, and of performance such as penetration rate and bit life. Drilling and boring are significant and integral aspects of both the mining and heavy construction industries. Together these constitute over 20% of the G.N.P. Drilling and boring represent the most arduous mechanical processes performed in industry. Their misapplication quickly leads to equipment destruction, hazards, and to major delays. The classification is unified in two ways: 1) for a particular rock class several parameters can be estimated, 2) the classification integrates most excavating activities (i.e. digging, ripping and even blasting), and is derived from ground control. The rock classification provides a job property, based on fundamental and index properties, which yields quick and rough estimates of vital information. However it does not obviate the need for a more thorough analysis, and maintaining field records. BACKGROUND In order to adequately describe a drilling operation the conditions, activity, and equipment must be characterized. Of these the major independent variables are the conditions. Conditions focus on the geologic mass and also consider whether the site is surface or underground. The primary component of the geologic mass is the rock type, detailed below in Rock Characteristics. The other components

Jan 1, 1983

By Heather Wright

Shovel operators are one step closer to having a better tool to operate and monitor their equipment. The development of a unified shovel interface is proceeding into phase three, focused on producing a standard application programming interface (API) for connecting onboard devices. This solution will positively impact safety, performance and productivity, and is the result of collaborative work driven by the Global Mining Standards and Guidelines Group (GMSG). Proof of concept revealed During the spring of 2013, Peck Tech Consulting was engaged to develop the working proof of concept (POC) software implementation, which integrates multiple vendors? systems into a single interface using one-to-two displays. As a result, the GMSG developed a functioning, manipulatable, unified shovel interface proof of concept and unveiled it at the World Mining Conference in August in Montreal. The proof of concept effectively provides a unified operator interface that pulls together the many divergent systems onboard large shovels.

Mar 1, 2014

By George F. Swindle

This paper discusses a composite of two coal reserve studies, each of which made use of a computer-based modeling system to assist in an evaluation of multi-seam deposits. The model permitted simultaneous consideration of seam thickness, seam structure, overburden thickness, over-burden ratio, and quality parameters for sulphur content, ash content, BTU values and the EPA Compliance index. The model is designed for use by a non-programmer, geologist or mining engineer. It enables the user, from a computer terminal in his office, to specify constraints (for example maximum um sulphur and maximum- ash content, minimum seam thickness and minimum BTU rating), and produces a report showing the volume, quality and location of that part of the total in place deposit satisfying all the constraints.

Jan 1, 1983

By Paul J. Cascone

This paper will discuss the science behind the development of a unique gold alloy for dental prosthetic applications. The alloy (GOLDTECH BIO2000) contains 99.7% gold providing unquestioned biocompatibility and unsurpassed esthetics. The topics discussed are: (1) How the alloy meets the functional requirements of a porcelain-fused-to-metal dental alloy. (2) How the alloy color affects the esthetics of the restoration and why the color of gold is best. (3) Overcoming the intrinsic malleability of gold when grinding the alloy surface. (4) Preventing the oxide color from interfering with the alloy esthetics. (5) Attaining excellent porcelain adhesion. (6) How the design of the restoration allows for the production of single and multiple unit restorations. Gold 2003

Oct 1, 2003

By Jesús E. Gómez

In the Summer of 2011, emergency repairs to the Jefferson Memorial North Plaza and Seawall were completed. These repairs were necessitated by settlement and lateral movement of the seawall and North Plaza which prompted the National Park Service (NPS) to initiate an investigation as to the possible causes of the movement, and commission a design for its mitigation. Information gathered from extensive instrumentation on site led to the design of a movement mitigation scheme that included demolition of the Ashlar Seawall and reconstruction of a new seawall. The new seawall foundation is an A-Wall consisting of vertical caissons and battered pipe piles connected to the seawall itself. The scheme provides resistance to future vertical and lateral movement of the North Plaza and the new seawall. Repair to the seawall and plaza began in December 2009, and was completed in August 2011. This paper discusses the mechanisms believed to be responsible for settlement and lateral movement, summarizes the procedure followed for design of the mitigation, and describes the construction methods and some challenges faced during the repair.

Jan 1, 2011

By Dawson CF

About 17% of the world's present day oil supplies comes from wells drilled in the continental shelf of some 28 countries. The demand for oil is increasing each year and is expected to quintuple in the next decade. In the same period, the demand for gas will climb to at least 20 times its present rate. In the next decade, the percentage of oil and gas obtained from offshore is expected to rise to nearly half the world's consumption. The offshore oil industry is currently striving to achieve new technological advances in the field of deep ocean operations, especially in face of adverse seas. While the emphasis was put on drilling vessels for exploration, the industry was slow in developing effective offshore construction vessels. Until a year ago, construction vessels were but large barges with construction equipment mounted on their decks. These vessels all shared the same severe limitation: When the sea exceeds a five-foot wave height (and in some cases as little as three feet) the conventional construction barge is forced to suspend operations. In face of an oncoming storm they must run for shelter. Their utilization, therefore, is limited and in rough weather areas, such as the North Sea or the Bass Strait is lower than 50%.

Jan 1, 1970

By Geo. H. Ashley

THE present critical state of the supply, distribution, and utilization. of coal and the necessity for pooling and zoning coals calls renewed attention to the lack of any fully adequate classification of coal. In the past coals have been classified as anthracite, semianthracite, semibituminous, bituminous, subbituminous coals, and lignite, and a few special types, such as splint coal and cannel coal. But under the term bitumi¬nous coal are included a great variety of coals differing markedly both physically and chemically. The term subbituminous coal covers as great a range of chemical differences. In order to distinguish these varieties of bituminous coals it has been customary to designate coals by names derived from the place where mined, or by the name of the bed from which it is mined. Thus, in the market reports, coals are quoted as Pocahontas coal, New River or Sewell coal, Moshannon coal, Ohio coal, Williamson County coal, Jellico coal, and so on indefinitely, no limit being set as to the boundaries of the area to which a given name is applied. Nor is there any scale by, which the coal from one place may be compared with the coal from some other district or some other bed. On the one hand, coals from the same district may be quite distinct and sell at very different prices or coal from the same bed may differ greatly in different districts; on the other hand, coals from different states may be so similar physically and chemically that one could replace the other in practical use without any appreciable difference in service.

Jan 8, 1919

By Gerry Roblesky

"IntroductionWestar Mining Ltd. is Canada's largest producer of metallurgical coal for the export market. It currently operates two mines, the Balmer Mine at Sparwood, British Columbia producing 6 000 000 tonnes per year and the Greenhills operation at Elkford, producing 2 100000 tonnes per year. Approximately 1600 people are employed between the two mines which operate independently but share common administrative services.Like most mining companies in Canada over the past three or four years, Westar has faced rising production costs along with flat or declining prices and demand for its products. In order to survive under these conditions it has become necessary to strive for decreased costs in any way possible. Over the past two years there has been a widespread introduction of microcomputers across the company. In order to satisfy increasing demand for accurate and pertinent information while at the same time increasing productivity, the microcomputer has become an invaluable tool.This paper describes some of the problems faced by a mine maintenance department in this operating climate and how they were solved with the help of a microcomputer. It also describes some of the problems that may be encountered both with equipment and people and recommends some ways that these might be minimized or avoided. Finally, an assessment of whether or not the move to microcomputers was a current and economical one, and a brief description of future plans and projects is given.The Maintenance OrganizationIn order to appreciate fully the role that microcomputers are playing within the Maintenance Department at Westar Mining, a little background on the organization and operating philosophies is in order. Most of the comments apply directly to the Balmer operations, however, the Greenhills operation is similar in concept.The mine maintenance organization operates on a fleet based concept with these departments reporting to the maintenance superintendent: haulage trucks, shovels and drills, loaders and Caterpillar equipment, maintenance services, and rebuild services.Each of these departments is headed by an assistant superintendent and is responsible for all maintenance on the equipment on the respective fleet. Shift foreman, planners, specialists and clerical staff are assigned to each fleet. A central engineering and administrative group consisting of one engineer and three clerical positions is responsible for maintenance engineering and centralized administrative services"

Jan 1, 1988

By Van Hoorn PD

For the development of BHP's Gregory open cut coal mine in Central Queensland a mini computer was successfully used to assist staff in the evaluation of the deposit and the planning of the mine. The Gregory deposit is essentially a single mineable seam deposit, however the systems developed may be applied to other coal deposits including multi seam occurences. The first phase of the Gregory computer evaluation and planning project involved the establishment of a borehole data base for the storage, retrieval and analysis of both strata and quality data. During the second phase a numeric block model of the coal deposit was created. Using this model reserve calculations were carried out by specifying the area with the aid of a digitizing tablet. The third phase involved the develop- ment of systems to simulate the dragline stripping operations including the rehandle percentage calculation, a dragline production schedule showing coal quantity and quality exposed, and a combined multi dragline operation schedule that can produce figures and graphs for up to 20 variables. A derivative of the operating plan was a programme that gave productioh cost estimates

Jan 1, 1978

By Saulo Brinco Diniz

O presente trabalho buscou explorar a aplicação da nanoindentação instrumentada na caracterização microestrutural e mecânica de materiais metálicos. Para isso foi utilizado um ultramicrodurômetro (Shimadzu, modelo DUH–211S) e um microscópio (Olympus, modelo BX51M) a fim de analisar uma chapa laminada a quente de uma liga de alumínio 7475-T7351. De acordo com algumas das possibilidades apresentadas, pode-se concluir que a nanoindentação instrumentada é uma ferramenta poderosa para a caracterização de materiais metálicos.

Aug 16, 2017

By Lucas Breder Teixeira

O uso de ferramentas de simulação numérica para análise estrutural vem se expandindo nos últimos anos, sobretudo utilizando o método dos elementos finitos. Nesse trabalho são apresentados dois exemplos de otimização de projetos envolvendo componentes de mecanismos de válvula gaveta, realizados pela Magnesita Refratários S.A. Partindo da geometria inicial até o produto final, é analisado como o campo de tensões é adequado a valores admissíveis, conforme modificações de projeto são realizadas. Por fim, é demonstrada a importância desse tipo de estudo para alcançar maior confiabilidade e segurança em projetos mecânicos.

Aug 16, 2017