Search Documents

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute for Occupational Safety and Health experimentally investigated various factor effects on cab air filtration system performance. The factors investi­gated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind effects on cab particulate penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that intake filter efficiency and recirculation filter use were the two most influential factors on cab penetration performance. Use of the recirculation filter reduced cab penetration by usually an order of magnitude over the intake air filter alone because of the multi­plicative filtration of the cab interior air. Intake air leakage and filter loading affected the cab penetration to a lesser extent, while wind had the least impact on cab penetration between the calm and 10-mph wind velocities tested. Adding an intake pressurizer fan notably increased intake airflow and cab pressure with only minor changes to cab penetration. A mathematical model was developed that describes cab penetration in terms of intake filter efficiency, intake air quantity, intake air leakage, recirculation filter efficiency, recirculation filter quantity, and wind penetration.

Jan 1, 2008

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute for Occupational Safety and Health experimentally investigated various factor effects on cab air filtration system performance. The factors investi­gated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind effects on cab particulate penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that intake filter efficiency and recirculation filter use were the two most influential factors on cab penetration performance. Use of the recirculation filter reduced cab penetration by usually an order of magnitude over the intake air filter alone because of the multi­plicative filtration of the cab interior air. Intake air leakage and filter loading affected the cab penetration to a lesser extent, while wind had the least impact on cab penetration between the calm and 10-mph wind velocities tested. Adding an intake pressurizer fan notably increased intake airflow and cab pressure with only minor changes to cab penetration. A mathematical model was developed that describes cab penetration in terms of intake filter efficiency, intake air quantity, intake air leakage, recirculation filter efficiency, recirculation filter quantity, and wind penetration.

Nov 1, 2008

By W. W. Agey

An inexpensive technique that laboratory studies indicated would significantly reduce seepage in irrigation canals was devised and tested through research sponsored by the Bureau of Reclamation and the Missouri River Basin Field Committee. Laboratory tests simulating optimum field conditions determined that easily applied sodium carbonate solutions made test beds of canal lining materials virtually impermeable for long periods. The study comprised alternative laboratory treatments of 3-inch-deep test beds of canal earths with 74 water-soluble chemicals in search of one 01' more that would effectively improve the water barrier characteristics of the component clays. Sodium carbonate, one of the least expensive, was among the most effective. The addition of 0,4 lb of reagent per sq yd greatly reduced the seepage from typical, highly permeable test beds. The reagent penetrated and sealed surface for about a 1.5-inch depth.

Jan 1, 1965

By E. C. Lane

This paper is a preliminary report of the results of the Bureau of Mines' twenty-second semiannual survey of motor gasoline marketed in the United States. A more detailed discussion of the whole survey is in preparation and will be published as a companion, report. The second paper, in addition to giving a more complete summary of the data included in this report, will present results of the determination of copper-strip corrosion (method 530.22),5 color (method 10.11),6 sulphur content (method 520.11) copper-dish evaporation residue (method 520.11),7 and gum content as given by the Bureau of Mines steam oven method.9 The retail price at the time the sample was taken and try will also be stated for each sample. The present paper deals specifically with data relating to gravity, vapor pressure, and distillation.

Jan 1, 1930

By Gerald T. Homce

Accidental contact of overhead electrical power lines by mobile equipment is a leading cause of occupational fatalities in the United States, accounting for 20% of on-the-job electrocutions. Overhead electrical power line proximity warning devices (PWDs) are intended to warn personnel if mobile equipment moves within some preselected minimum distance of an energized overhead electrical power line. Two commercially available PWDs were tested at the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). The objective of the tests was to document performance capabilities and limitations for these PWDs by identifying factors that can influence their operation. The two PWDs evaluated in this research are the SIGALARM Model 210 marketed by Allied Safety Systems, LLC, and the ASE Model 2100 from Allied Safety Engineering. Both of these devices operate by measuring the electric field present around energized power lines. The PWDs were installed on a government-owned 22-st (20-mt) rough terrain crane. A purpose-built test site used for this research at PRL allowed operation of the crane near a variety of power line configurations operating at up to 25 kV. Most of the tests involved positioning the crane adjacent to one or more overhead power lines, adjusting sensitivities of the PWDs to alarm when the crane boom was approximately 20 ft (6.1 m) from the power lines, swinging the crane boom toward the lines under a wide variety of test conditions, and finally, for each unique set of test conditions, documenting the deviation from 20 ft (6.1 m) for actual alarm activation. Test results show that several factors can adversely affect PWD performance. PWD alarm accuracy generally deteriorated when operating with a boom position significantly different than that used for the device?s last sensitivity adjustment. Another factor that can affect PWD performance is configuration of the overhead power line(s) involved. Accuracy of alarm activa­tion distances was best for simple single-circuit installations, but degraded for multiple circuits on the same poles. This degradation was slightly greater for installations with different voltage levels and/or a combination of vertical and horizontal conductor arrangements. Performance also degraded for crane operation between two intersecting power line installations, especially for intersecting lines at different voltages. An additional aspect of power line configuration shown to influence PWD accuracy was phase sequence on the power line circuit(s). Specific phase con­ductor arrangements and combinations, particularly in multiple circuit installations, resulted in either improved or degraded accuracy.

Jan 1, 2008

By Ralph H. Whaite

To assist the anthracite industry obtain technical data on pneumatic packing, the Federal Bureau of Mines imported a pneumatic packing machine from Germany and installed it in a mine of a cooperating company in the Northern anthracite field of Pennsylvania. This report covers the second in a series of experiments in applying pneumatic packing for controlling strata movement (subsidence) above mine workings in the Pennsylvania anthracite region. The first experiment2/ was begun in January 1950, in a section of the mine where about 50 percent of the original coal remained in the form of pillars; since the company did not plan to mine the pillars in this particular area, pneumatic packing of the chamber voids was done for test purposes only. During this initial test the machine was operated on 204 shifts, and 652,400 cubic feet of breaker refuse material (22,834 tons) was packed into the voids of 16 chambers. The work was completed in December 1951.

Jan 1, 1956

By Welby G. Courtney

This publication reviews recent U.S. Bureau of Mines studies of frictional ignition of a methane-air environment by coal mining bits cutting into sandstone and the effectiveness of remedial techniques to reduce the likelihood of frictional ignition. Frictional ignition with a mining bit always involves a worn bit having a wear flat on the tip of the bit. The worn bit forms hot spots on the surface of the sandstone because of frictional abrasion. The hot spots then can ignite the methane-air environment. A small wear flat forms a small hot spot, which does not give ignition, while a large wear flat forms a large hot spot, which gives ignition. The likelihood of frictional ignition can be somewhat reduced by using a mushroom-shaped tungsten-carbide bit tip on the mining bit and by increasing the bit clearance angle; it can be significantly reduced by using a water spray nozzle in back of each bit, which is carefully oriented to direct the water spray onto the sandstone surface directly behind the bit and thereby cool the hot spots formed by the worn bit. A bit replacement schedule must be used to avoid the formation of a dangerously worn bit.

Jan 1, 1990

By Henry Kreisinger, WALTER T. RAY

This bulletin contains a statement of certain results that will be embodied in a report describing investigations of the combustion of fuel made by the United States Geological Survey and the Bureau of Mines in a specially constructed long furnace. The furnace forms part of the fuel-testing plant at Pittsburg, Pa., which was established and equipped by t.he Geological Survey, but passed under the control of the Bureau of Mines on July 1, 1910, when a t.ransfer of fuel-test.ing investjgations, authorized by act of Congress, became effective. The work discussed in this bulletin was done under the direction of the Geological Survey. The furnace was designed and built for an experimental study of the processes of combustiop, this study being part of a comprehensive plan for testing fuels to determine their heat value and the manner in which they can be used to best advantage. Although the main object of the researches made with the furnace by the Geological Survey was to examine critically the production of sensible heat by combustion along the path of the gases rising from the fuel, an interesting as well as important side problem developed in the study of the simultaneous dissipation of the heat through the walls and roof . of the furnace. Thus incidental data were collected on the temperature gradient through the walls at several places. These temperature data. (together with the heat conductivity of the material of the walls) formed the basis for calculating the heat dissipated through the walls. The object of this report is to present and discuss these temperature data. The discussion particularly concerns the air-space type of wall construction as compared with the solid brick wall or walls type, in which the air space is filled with some solid material of low heat conductivity. The conclusion of the authors, which perhaps will surprise some readers, is that, so far as loss of heat is concerned, a solid wall of brick or any ordinary material is preferable to a hollow wall of the same total thickness, especially if the air space in the hollow wall is near the furnace side. There is a general belief that l?ince air is a poor conductor of heat, air spaces built into the walls of a furnace will prevent or reduce heat dissipation through the wa.lls. Although there may be instances of furnace walls in which such construction reduces the rate of heat flow through them, yet as a rule the effect of the air space is just the opposite. While the heat does travel very slowly through the air by conduction, it leaps over the air space readily by radiation. Although this latter mode of heat propagation is common in nature, the laws governing it are not generall;y known and are seldom taken into consideration when furnace walls are being designed. It may be stated here that the quantity of heat passing through a. portion of a solid wall by conduction depends on the difference between the temperatures of the two planes limiting the portion of the wall. The quantity of heat that passes across the air space in the waH depends on the difference of the fourth powers of the absolute temperatUI: es of the surfaces inclosing Hie air space. It follows that, in case the heat. passes by conduction through the solid'portion of the wall, the loss remains approximately the same so long as the temperature of the two limiting planes remains constant, no matter what may be the temperature of the two planes. On the other hand, the heat passing across the air space by radiation increases rapidly with the temperatures of the inclosing surfaces, although the difference between these temperatures may remain constant. This feature will be shown by curves in the latter part of this paper and thoroughly discussed. The important point is that the air space, which is advantageous in the walls of a refrigerator because the temperatures are low, is objectionable in a furnace wall because the temperatures are high. It is customary to put air spaces in furnace walls between the firebrick linings and the common brick. Usually the fire-brick lining is only half a brick thick, which construction brings the air space too close to the furnace. The result is that the temperatures of the surfaces inclosing the air spaces are too high, and in consequence too much heat is radiated across the spaces. The heat passing through such walls would be much reduced if the air spaces were filled with brick, or, better, with some cheap nonconducting materials, such as ash, sand, mineral wool, etc. Even where the fire-brick lining is one brick thick (9 inches), the temperature in the furnace may be high enough to raise the temperatures of the air-space surfaces so much that the heat radiated across the space will amount to more than would the heat conducted through a filling, were the filling only common brick. This last statement is amply justified by the data here presented.

Jan 1, 1911

By P. D. Laverty

This report describes a processing method developed by the U.S. Bureau of Mines to produce high-quality flake graphite from the steelmaking waste known as kish. The kish produced by current steelmaking practices is a mixture of graphite, desulfurization slag, and iron that is skimmed from the molten iron feed to the basic oxygen furnace. It is estimated that the graphite content of kish discarded by U.S. steel plants is more than sufficient to meet the total U.S. demand for flake graphite. That need is now filled by natural graphite from foreign sources. Kish was treated by a combination of screening and hydraulic classification to produce a concentrate containing greater than 70 pct graphite. Leaching of the concentrate with hydrochloric acid solution gave a graphite product with 95-pct purity. An optional secondary leaching operation with hydrofluoric acid produced graphite with a purity of 98 pet or greater. The flake size of graphite from kish ranged from 10 mesh down. Evaluation of test samples by industrial graphite users indicated that kish graphite is a suitable substitute for the natural material for most uses. A process flowsheet and material balance for pilot plant design are presented.

Jan 1, 2010

By P. C. McWilliams

Researchers at the U.S. Bureau of Mines investigated the use of close-range photogrammetry and subsequent stereo digitizing to obtain data from rock fracture roughness profiles. The photogrammetric process yielded results that were acceptable but somewhat inferior to those obtained by a mechanical profilometer. On the basis of this study, further pursuit of photogrammetry as a data collection method in mining is proposed. Fractal geometry was investigated as a means of measuring the roughness of rock fracture profiles. Four fractal algorithms were used: divider method, modified divider method, box method, and spectral method. A comparison of the methods gave ambiguous results. Brown's modified divider method provided the best means of obtaining the fractal dimension. Shear strength estimates were obtained using the parameters of the modified divider method and Myers' Z2 measure. Because of differences in results when comparing the different ways of obtaining the fractal dimension, future users of fractals in studies of rock fractures are advised to cross-check their results carefully.

Jan 1, 2010

By E. C. Lane

This paper is a preliminary report of the results of the Bureau of Mines' twenty-second semiannual survey of motor gasoline marketed in the United States. A more detailed discussion of the whole survey is in preparation and will be published as a companion, report. The second paper, in addition to giving a more complete summary of the data included in this report, will present results of the determination of copper-strip core lion (method 530.22), color (method 10.11), sulphur content (method 520.11) evaporation residue (method 530.1), and gum content as given by the Bureau of Mines steam oven method.9 The retail price at the time the sample was taken and tax will also be stated for each sample. The present paper deals specifically with data relating to gravity, vapor pressure, and distillation. It has been the feeling of some investigators that the practice, followed in previous semiannual surveys, of grouping all types of motor fuel together without discriminating between "competitive price gasoline," benzol blends, Ethyl gasoline, "high-test" fuels, etc., has detracted from their usefulness because the data did not permit drawing conclusions in regard to any one type of fuel, and tended to obscure differences between fuels of the various types. Therefore, in order to remedy this condition, the samples of the present survey have been divided into two groups; one called "competitive-price gasoline" and a second group called "premium-price motor fuels."

Jan 1, 1930

By Gregory J. Chekan

The U.S. Bureau of Mines is investigating longwall panel and gate road layouts to increase coal recovery and reduce multiple-seam interactive problems. This report presents design practices for longwall mining multiple seams to provide mine planners and operators with practical guidelines for designing productive longwall mines. Key aspects of mine design that control longwall interactions are examined, including sequencing of seams, design of gate road pillars, and orientation of gate roads and longwall panels. Theories that describe stress transfer between multiple scams and the mechanics of interaction are addressed in relation to geology. Common longwall designs were further investigated using a boundary element model, MULSIM/NL. The model provided insight into relative stress transfer and distribution that occurs between longwall operations in multiple seams. Findings from the model show that (1) a longwall panel should be mined from the gob to the solid coal of an overlying mine, because the stress concentrations are lower; the approach angle should be kept under 30°; and (2) when mining in descending order, superpositioning gate roads usually produces the worst stress condition. To prevent this, the overlying isolated gate roads should be positioned from the centerline toward the headgate side of the underlying panel.

Jan 1, 1993

By James A. West

The South Asian countries of India, Pakistan, Afghanistan, Ceylon, Nepal, Bhutan, and Sikkim arc to varying-degrees just beginning to achieve significant economic and industrial development. These countries are richly endowed with certain mineral resources, and development of these resources is being accelerated. In 1965, the mineral industry remained a relatively small sector of the region's economy, accounting for only about 1 percent of its estimated gross national product of $62,528 million. Nevertheless, the estimated $630 million total value of minerals produced in South Asia during 1965 represented an increase of nearly 15 percent t over that of 1964. India continued as the dominant mineral producer of the region, accounting for 85 percent of the total value of all minerals produced ill 1965. India increased its output of iron ore, manganese, mica, coal, and petroleum. Pakistan accounted for 13 percent of the value of the region's output and recorded increased output of iron ore, chromite, coal, natural gas, and most other minerals. The small mineral industry of Ceylon attained remarkable growth in the production of ilmenite, graphite, and gem stones. The mineral industry of Afghanistan remained relatively insignificant, although development of large known resources of natural gas was continued, Nepal, Bhutan, and Sikkim produced no commercially significant quantities of minerals in 1965.

Jan 1, 1967

By George Markon

The rapid growth and development of the Soviet coal industry rank the U. S. S. R. with the United States among the leading coal-producing countries. The coal resources of the Soviet Union are among the largest in the world, although coal development has been hindered by the disadvantageous location of the coal deposits with respect to the major consuming centers. Although coal production in the U. S. S. R. reached a record high, the total energy output of mineral fuels in 1957 was still far below that of the United States because a significant part of Soviet coal output was lignites or lower rank coals. Although the Soviet coal industry soon may exceed that of the United States in tons produced, the energy equivalent of Soviet output will be considerably less because of the inclusion of a high percentage of lower rank coals. Energy sources in the United States also involve large quantities of oil and natural gas, whereas coal supplies most primary energy in the Soviet Union.

Jan 1, 1959

By A. F. Baker

Tests were conducted in commercial foundries to determine the suitability of calcined anthracite as a cupola fuel. The calcined anthracite performed satisfactorily at two of the three foundries where iron-melting tests were conducted. Performance at the third installation was unsatisfactory because metal temperatures deviated widely and, in general, were lower than is desirable for the type of castings being made.

Jan 1, 1963

Mine drainage and mine reclamation are topics of major interest to the mining industry, federal and local governments, and the general public. This publication and its companion three volumes are the proceedings of a conference held in Pittsburgh, Pennsylvania, April 24-29, 1994. There were twelve sessions (69 papers) that dealt with mine drainage, including modeling, geochemistry, prediction, treatment, control strategies, characterization, hydrology, and case studies. These sessions comprise volumes 1 and 2. The six sessions (34 papers) that dealt with reclamation and revegetation of disturbed lands are included in volume 3. Volume 4 includes the six sessions (34 papers) that dealt with such topical issues as fires at abandoned mine sites, subsidence, hydrology, mine wastes, and policy. Poster session presentations are represented by 49 papers and 92 abstracts that have been placed in the back of volumes 2, 3, and 4, consistent with the subject of that volume.

Jan 1, 1994

By Frederick K. Allgaier

This report presents the final data from a 5-yr Bureau of Mines study designed to determine the surface subsidence characteristics resulting from longwall coal mining in a geologic environment common to the Western United States, It includes a description of the geologic setting of the study site, the mine plan, measurement techniques, and results of the monitoring program. Measured subsidence values were obtained over four adjacent longwall panels- Major subsidence characteristics such as longitudinal and transverse profiles, angles of draw, time-related subsidence development, and critical width are discussed. The maxima subsidence value of 5.8 ft was 68 pct of the mining thickness. The average angle of draw was 30°, Subsidence at the center of the first panel continued for 46 months following undermining. The lengths of the longwall panels precluded a definitive determination of the critical width and maximum possible subsidence.

Jan 1, 1988

By S. H. Lorain

This paper is one of a series being published by the Bureau of Mines describing the mines and mills and subjects related to mining in western mineral areas. Although mining districts in the Tobacco Root Mountains are numerous there is a strong similarity in the character of the ore deposits and in the climatic and economic conditions affecting mining throughout the region. Individual mines are small, but the production of lode mines

Jan 1, 1937

By F. M. Goodwin, John Campbell, G. W. Jones

"INTRODUCTION In cooperation with the Boston Edison Co. and the Boston Consolidated Gas Co. of Boston, Mass., a survey has been conducted continuously since 1929 by the Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Boston Edison Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes from May 1, 1933, to October 15, 1937. Yearly reports. 6/ on the results obtained since the beginning of the survey have been published.The methods and procedure of conducting the survey in 1937 were the same as heretofore."

Jan 1, 1939

By Robert J. Brennan, Edward R. Navrocky, John W. Buch

In an effort to establish a highly productive mechanized mining system for anthracite beds pitching between 10 ° and 20 ° , for which conventional mobile equipment is not adaptable , the Bureau carried out an experiment in longwall mining using an Anderton- type drum cutter loader and friction - type yielding steel roof supports . The roof- support system proved to be inadequate for breaking the overhanging roof at the break line supports , with the result that the roof broke over the solid coal . The accompanying subsidence destroyed the continuity of the roof in the work area , and the project was discontinued .

Jan 1, 1964