Search Documents

By E. T. Turkdogan, W. L. Worrell

The rate of reaction of hydrogen sulfide with ferrous sulfide was studied by measuring the initial rates of sulfidation of iron strips in hydrogen sulfide-hydrogen-argon mixtures at 670°, 800°, and 900" C. The time-dependent surface sulfur activity is derived from the instantaneous rate of sulfidation with the assumption that diffusion in the sulfide layer is in a pseudo-steady state with the gas-sulfide chemical reaction. The rate of sulfur transfer from hydrogen sulfide to the surface of iron sulfide is proportional to the partial pressure of hydrogen sulfide and inversely proportional to the activity of sulfur at the surface of the sulfide layer. The derived rate equation is based on the assumption that most of the surface sites on the chemisorbed layer of iron sulfide are occupied by sulfur atoms and that the slow rate-controlling reaction is the dissociation of hydrogen sulfide on the chemisorbed layer. The experimental results are in reasonable accord with this reaction model. 1 HE slow approach to parabolic growth rate in the sulfidation of iron in hydrogen sulfide-hydrogen mixtures is a manifestation of slow approach to surface equilibrium between the gas and the surface of the sulfide layer. For example, at 800°C and Fig. 7 in Part I, the parabolic growth rate begins after approximately 1 day of sulfidation time. With decreasing temperature and decreasing partial pressure of hydrogen sulfide, the time necessary to reach gas-sulfide surface equilibrium is much longer. These observations are similar to those reported previously by Turkdogan et al.' on the oxidation of iron to wustite in hydrogen-water vapor mixtures. The slow approach to gas-sulfide equilibrium is well-demonstrated by the results in Fig. 1 where the square of the weight gain per unit area, ( g S per sq cmI2, is plotted against time for gas mixtures having PH g//>H = 1.0 with 0, 25, 50, and 67 pct Ar at 800°C. The value of 1.5 X lo-' (g S per sq cm)' corresponds to almost complete sulfidation of the iron strip (- 0.05 cm thick) to iron sulfide. The points fall on S-shaped curves. If the inflection parts of the curves are considered to be linear, thus indicating parabolic growth rate and the establishment of gas-sulfide equilibrium, their slopes would have to be the same for a fixed ratio in the gas mixture. Such is not the case, and the slopes for the "linear" parts of the S-shaped curves are lower than the value when gas-sulfide surface equilibrium is established. The subject matter of this paper is the kinetics of the surface reaction of hydrogen sulfide with iron sulfide during the early stages of sulfidation of an iron strip. EXPERIMENTAL RESULTS The apparatus and materials used were the same as those discussed in Part I. In the present experiments of relatively short duration, a purified iron strip, 5 by 2 by 0.05 cm, which was suspended in the uniform hot zone of a vertical zircon tube, reacted with a flowing gas mixture of hydrogen sulfide-hydrogen-argon. The sample was suspended from a gold chain attached to a calibrated silica spring. The amount of sulfur picked up by the iron, which formed a layer of iron sulfide, was determined by measuring the displacement of a reference point on the silica spring, using a cathetom-eter. In all cases, the degreased sample was first annealed in a stream of oxygen-free dry hydrogen for several hours to remove any impurities such as oxygen, nitrogen, or carbon which might have been present on the surface of the sample.' The rate measurements were carried out at 670°, 800°, and 900° C in hydrogen sulfide-hydrogen-argon mixtures with pH2 s/Ph2 ratios from 4 to 0.1. In a few experiments of short duration no sulfur deposition was observed in gas mixtures with (comments concerning sulfur deposition at high pH s/ph ratios were made in Part I.) Typical examples of the results obtained are shown in Fig. 2 for two temperatures and two gas compositions. With the present experimental technique, reproducible rate data could be obtained only after a uniform

Jan 1, 1969

F. G. CLAPP, New York, N. Y. (written discussion *).-Whatever processes of appraisal have been found most correct and feasible in one field or group of fields will generally prove most adaptable in others. So far as the California fields are concerned, Mr. Requa's paper appears to outline the most up-to-date processes of appraisal. It remains, then, to discuss and adapt these and to make such revisions in methods and processes of calculation as will give us results elsewhere. The trouble about most attempts to place a value on oil lands, whether in this country or elsewhere, has been that many of the so-called "experts" called upon to express an opinion either have not possessed the requisite engineering and geological knowledge to make an accurate appraisal of the lands, or that they were not furnished with sufficient information for the purpose in hand. The Independent. 011. Producers' Agency of California, for whom Mr. Requa's original report was prepared, had many advantages in this respect not generally available to engineers making reports, as all existing information seems to have been at the experts' disposal within the limits of a large number of properties, practically commensurate with the extent of the fields in question. Hence the report could be and was more accurate than any similar report for a single company is likely to be in other fields. Very few companies are so exempt from competition that all the data on neighboring leases of other companies will be freely turned over to them. In many companies, certain available data are concealed from the engineer who makes the reports, particularly if the properties are supposed to be worth less than their apparent value. In the case of other companies, having the best of intentions, the data are insufficient to help the engineer greatly in his appraisal, simply because the oil business has been so, unsystematic in most fields that only the largest and wisest companies have kept accurate figures regarding runs and gravity of oil from individual wells and from different depths. In many wells, which ran wild for clays or weeks in the older fields, there was a waste which is not recordable with exactness. These and many other difficulties confront even the most experienced expert in actual practice outside of the California fields. We may justly say, therefore, that an engineer in other fields of the United States and in the European, South American and Asiatic fields, must not only begin where the Independent Oil Producers' Agency

Jan 4, 1918

By P. H. Delano, Will H. Coghill, G. D. Coe

Data concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as " grindability-index numbers," but grind-ability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pull'erized product by a method comparabLe with- commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulvcrizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation,it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-¾-inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horsepower-hours." The channel-roller pulverizer hereinafter described is believed to meet these requirements. History oF the Machine The, work started when Ralph W. smith, engineer, St. Genevieve Lime Co., St. Cenevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasive-ness of dentifrices,1 and it was thought the same principles might be applied to coal, Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By Will H. Coghill, P. H. Delano, G. D. Coe

Data concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as " grindability-index numbers," but grind-ability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pull'erized product by a method comparabLe with- commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulvcrizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation,it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-¾-inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horsepower-hours." The channel-roller pulverizer hereinafter described is believed to meet these requirements. History oF the Machine The, work started when Ralph W. smith, engineer, St. Genevieve Lime Co., St. Cenevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasive-ness of dentifrices,1 and it was thought the same principles might be applied to coal, Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By AIME AIME

ROBERT F. MEHL was born in Lancaster, Pa., March 30, 1898 and graduated from Franklin and Marshall College in 1919. He then went to Princeton and was granted his doctor's degree in physical chemistry in 1924. Two years as head of the department of chemistry at Juniata College, followed by a like period as National Research fellow at Harvard, working with T. W. Richards and Albert Sauveuir, satisfied Bob's immediate affections for college and university life and prepared him to turn temporarily to other fields.

Jan 1, 1938

By G. J. Wilson

Review of difficulties experienced in drilling directional wells in the offshore Grand Isle Block 43 field showed most failures of drill pipe, drill collars and casing to have been associated with excessive dog-legs. Alleviation of difficulties was approached by synthesizing theoretical and practical concepts in a planned dog-leg control program. Preventive measures necessary to control dog-leg severity and corrective measures used to reduce unacceptable doglegs are discussed. When other measures fail, deliberative measures as outlined can be employed after the probable cumulative fatigue damage to be sustained by the drill pipe has been determined. Results of a program successful in virtually eliminating problems stemming from excessive dog-legs indicate that control of dog-leg severity in directional wells is feasible and will cause no decrease in the over-all drilling rate. INTRODUCTION Prompted by an increasing frequency of drill pipe, drill collar and casing failures, a study of 50 directional wells representing 592,000 ft of hole, including 444,000 ft of deviated hole, drilled in the offshore Grand Isle Block 43 field was conducted in early 1965. A number of drill pipe washouts and six keyseating problems were recorded and a detailed review was made of 16 failures which had required fishing effort in 10 of the 50 directional wells drilled prior to June, 1965. These problem wells are exemplified by Wells G and F for which pertinent data are shown in Figs. 1 and 2. Data pertaining to all of the 16 failures are summarized in Table 1. Inspection of these data shows most of the problems to have been associated with dog-legs in excess of theoretical limits suggested by Lubinski' and excessive dog-legging is indicated to have been concomitant with whipstocking in several of the problem wells. Results of the investigation agreed with those reported by Schenck2 who had concluded that problems could be expected when dog-leg severity exceeded limits proposed by Lubinski. Since Schenck had demonstrated the desirability and feasibility of drilling directional wells without excessive dog-legging, a dog-leg control program was established in June, 1965 for wells drilled in the Grand Isle Block 43 field. This paper reviews the methods by which theoretical and practical concepts were synthesized to develop a program of preventive, corrective and deliberative measures which virtually eliminated problems stemming from excessive dog-legs in directional wells. Dog-legs of a magnitude causing no damage are referred to as permissible +1CONTINENTAL OIL CO. HARVEY, LA.

By C. H. North, L. E. Lynd, W. W. Anderson, H. Sicurdson

D. R. Grantham (Institute of Mining and Metallurgy, London, England)—This paper is a very valuable contribution to our knowledge of ilmenite and its alteration products. Two aspects are not treated in the paper and further information would be valuable. How far are the alteration processes described influenced by the original composition of the ilmenite? The word gangue is used but it is not clear whether this refers to other chemical constituents in the ilmenite, e.g., magnesia, or to other minerals loose or in composite grains. Has the work described been related to specific gravities? Pure ilmenite is stated to have a specific gravity of 4.79. Some varieties range up to over 5.0, while high magnesic varieties have a specific gravity ranging to below 4.2. Alteration to hematite might lower the specific gravity and a porous texture due to the removal of iron and the formation of rutile might also lower it. As specific gravity is a quick method which often gives an approximate indication of composition, data on the above would be valuable. L. E. Lynd (authors' reply)—Because of the way in which beach sand deposits were formed, it is impossible to tell exactly what the original composition of the parent ilmenites might have been. Information on the influence of original composition on the alteration processes must be derived from other sources, perhaps by comparing the alteration products formed from ilmenite in place in a variety of rock deposits, where parent ilmenite and its alteration product can be recognized. No information of this type has yet been brought to our attention. The material referred to as gangue includes all constituents other than oxides of titanium and iron. Nearly all of this was present as separate grains of garnet, augite, hornblende, quartz, feldspar, spinel, or other gangue minerals. Inclusions of gangue minerals within ore grains were rare, and we believe there is little MgO (1 pct or less) or other impurity actually held in the ilmenite structure in any of the concentrates studied. No specific gravity measurements were made on the samples studied. However, the suggestion that alteration involving loss of iron would lower the specific gravity is a very reasonable one, and is in accord with the findings of Creitz and McVay (Ref. 9 of our paper) who reported two magnetic opaque fractions from Trail Ridge, Fla., to have the following specific gravities and pompositions: The specific gravity of this porous, high TiO² alteration product of ilmenite is closer to that of rutile (4.25) than to that of ilmenite. Due to the porosity, it may even be less dense than rutile, although lower in TiO² and higher in iron.

Jan 1, 1955

AT a luncheon attended by engineering leaders representing every section of the country, Col. Arthur S. Dwight, president of the American Institute of Mining and Metallurgical Engineers, and Charles F. Rand, chairman of the Engineering Foundation, past president of the Insti-tute and its present treasurer, on Thursday, July 20, were decorated with the Croix de Chevalier de la Legion d'Honneur by the French Government for distinguished service in engineering tending to closer and more felici-tous relations between the two countries. The decorations were conferred by Consul General Gaston Liebert. In a speech extolling the war work of the American engineer, M. Liebert declared that Germany had been definitely foiled in her attempt to cripple France industrially for a generation by wrecking the coal mines of northern France. Three-fourths of these mines, M. Liebert said, were in full working order and the remainder will be in complete operation within two years. The Germans thought that it would take from 15 to 20 years to accomplish this. M. Liebert said that reconstruction is going on rapidly in northern France, two-thirds of whose indus-tries are now working. The French Government, he said, is planning water-power improvement on a vast scale, which will soon make unnecessary for France to import a single ton of coal. He urged that French students be sent to America to study engineering. In presenting the decorations, Consul General Liebert eulogized Colonel Dwight and Mr. Rand as personify-ing the spirit and service of the American engineer, which, he said, was a powerful factor in the victory over Germany. He spoke of the growing friendliness between the United States and France and described this ceremony as an epoch in international relations. Calvin W. Rice, secretary of the American Society of Mechanical Engineers, who presided, repeated that international unity among engineers was the dream of Andrew Carnegie, who saw in the efforts of the engineer and the scientist the hope of civilization. Mr. Rice said in part: In the Declaration of Independence occurs the statement that all men are created free and equal. Jefferson was familiar with the writings of Rousseau. In fact, he was a remarkable linguist notwithstanding that he wrote the Declaration of Independence when only 32 years of age. He was one of the very few ambassa-dors in the history of the United States who could speak the language of the country to which they were sent. The interpretation of the passage in the Declaration of Independence is that all men have equal opportunity, not that they are born with equal ability.

Jan 8, 1922

By Charles C. Hawes

DETERMINATION OF SILICA OXIDE iron ores usually are found in intimate association with silica and phosphorus compounds. Their quantitative separation and purification sometimes present difficult problems to the chemist. Silicic acids may represent various degrees of dehydration. They are exeedingly weak, but combine with metallic oxides and form some of the most stable oxides in nature, the silicates. When iron ores are treated with hydrochloric acid, they yield practically all their iron. However, apart from rare exceptions, varying amounts of insoluble residues of silica, alumina, lime, magnesia and compounds of phosphorus, sulphur, titanium, chromium and others will be left. If the oxides of silicon, aluminum and titanium are present in small quantities, the insoluble residue is generally very small, but the presence of these oxides is more usual in larger quantities. Therefore, only a special treatment can break the bond between these elements. Ore Residues Acids remove the soluble constituent of the ore, leaving the insoluble residue, which chemically is rock or gangue and must be treated accordingly. Alkali carbonates are used frequently to break up the residue, but other fluxes have also been recommended, such as a number of lead and boron salts. The introduction 0f these salts, which offers certain advantages, requires, however, their removal before the other constituents can be analyzed, and this elimination is sometimes difficult. Usually in quantitative analysis silicates are dissociated by fusing them in a platinum crucible with sodium carbonate, thereby forming sodium silicate, Na2SiO3, sodium aluminate, Na2Al204, sodium titanate, Na2TiO3, and carbonates of other elements. All the carbonates are soluble in hydrochloric acid, but also some silicic acid is formed that must be rendered insoluble. To this end the solution is evaporated several times, as the first evaporation still leaves as much as 5 per cent of the silica soluble. Even after a number of evaporations, minute quantities of silica may be found with the iron and alumina present. Perchloric Acid as an Agent for Dehydrating Silicic Acid Perchloric acid, HC104, (60 per cent), has been used for years as a solvent, but few chemists have used it to dehydrate silica. It is derived from anhydrous perchloric C1207, which is most unstable and dangerous. Perchloric acid is a strong oxidizing agent, which boils at 203°C. It is more effective in rendering silica insoluble than any other known agent, and most rapid in action. After perchloric acid is added to a mixture containing silicic acid, the resultant solution is

Jan 1, 1945

By J. Randel Hill

The 64th Texas Legislature passed the "Texas Surface Mining and Reclamation Act," Chapter 131, Texas Natural Resources Code (subsequently referred to as "the Act"), at a point in time when little surface mining had taken place within the state. Thus, enactment of regulatory control governing mining operations in our state has, for the most part, preceded widespread, intensive mining activity. I should point out that the statute applies only to the extraction of coal, lignite, uranium and uranium ore. A recent opinion rendered by the Attorney General's office has stated that extraction of the named elements, when it occurs incidental to the extraction of other materials, e.g., clay, is not not an activity subject to the Act. An important theme of the Act, frequently overlooked in other environmentally oriented legislation, is recognition of the Act's affect on the mining industry. The Act states that "the extraction of minerals by surface mining operations is a basic and essential activity making an important contribution to the economic well-being of the state and nation" and, in reference to reclamation being accomplished contemporaneously with mining, provides a recognition that "the extraction of minerals by responsible mining operations is an essential and beneficial economic activity." This legislative recognition is, of course balanced against the need for proper mined land reclamation, the rights of surface owners, the need to guard against unreasonable degradation to land and water resources and numerous other actions or events that the Legislature wanted protected. Another rather pervasive general theme that is established in the Act is the concept that the agency is entitled to obtain whatever information, or take whatever action, that appears reasonably necessary to effectuate the purposes of the Act. This concept, coupled with the detailed requirements placed on mining operations in the portions of the Act dealing with Permit Applications, Reclamation Plan and Reclamation Standards, easily insures that surface mining activities can and will be regulated to the extent necessary. Section 131.102(b)(2) is probably the most relevant provision in the Act which deals with the preclusion of mined lands becoming waste lands. This portion of the Act states that the surface mining operator shall: ". . . restore the land affected to the same or a substantially beneficial condition. ." In this language the Legislature had made it abundantly clear that the abandoned or orphaned lands found in some of the Eastern states, will not be tolerated in this State, and provided the Commission with a degree of latitude to determine what condition would be appropriate in each individual mining situation. I bring this area of the Act to your attention because it is the area which has received the most inquiries and concern by operators, i.e. what does "substantially beneficial" constitute? The Commission's staff has spent a considerable amount of time wrestling with the statutory language "substantially beneficial" to determine the legislative intent and provide operators with guidance of what they can expect. In this regard, the most definitive criteria in our opinion lies in the Act's legislative hsitory. The Legislature had before it basically three reclamation standards namely: House Bill 656, considered to provide the most stringent reclamation standard and identical to Senate Bill 66; House Bill 1717 which was supported by industry spokesmen and was considered to contain the least stringent reclamation standard; and Senate Bill 55 which was adopted by the Legislature. During the Bill's initial hearing before the House Environmental Affairs Committee, the House sponsor of the Senate Bill 55, which was the Bill eventually adopted, made the following statement: (I am quoting verbatim from the Committee's transcript although substituting the speaker's reference to the authors names with the Bill's numbers.) "An example of the differing approaches of the four bills can be seen in the area of reclamation standards and this is critical. House Bill 656, talking about restoring the surface of the land, House Bill 656 has this statement: 'At least fully capable of supporting the use to which it was capable of supporting prior to any mining or any higher or better use.' In other words you have to restore it to the level it was prior to the mining. Senate Bill 55: 'Restore the land to the same or substantially beneficial use.' Substantially beneficial use. (Emphasis his) House Bill 1717 says: 'Restore insofar as practical to appropriate beneficial post-mining use.' So that House Bill 1717 said to, 'restore insofar as practical to appropriate beneficial use. I think that's too weak, whereas I think the House Bill 656 that would call you to restore it to at least the use it had prior to the mining may also be too tight the other way. I think the Senate Bill 55 approach is down the middle of the road which says that you do restore it to the 'same or substantially beneficial use,' is a proper way to go there." Therefore, the conclusion that we have drawn from the legislative history of the bill is that the extent of reclamation required by "substantially beneficial" may be something other than the use it was prior to

Jan 1, 1979

By W. Mitchell, B. H. Bergstorm, C. L. Sollenberger

A unique compression testing machine was constructed to load individual 1/8 to I-in. spheres of glass, etc., at rates from 100 to 100,000 lb per min. During loading the applied load was continuously plotted us the deformation of the sphere-platen system. The load-deformation curve conforms to the theory of elasticity. The spheres were surrounded by steel retaining rings or by gelatin (to prevent secondary fracture). The product size modulus was determined from screen analyses. The data shows: 1) Energy input per unit mass is inversely proportional to the product size modulus (or directly proportional to the surface area per unit mass). 2) Increased loading rates slightly increase the energy input per unit mass required for fracture without affecting the preceding relationship. Theory and experiments show that much of the input strain energy is transformed into kinetic energy of fragments at fracture, this being a reason efficiencies based on "surface energies" are exceedingly small. This large kinetic energy component is usually dissipated as heat but may be partially reclaimed because impact of fragments against the surface of steel retaining rings causes additional comminution. There are currently several theories of crushing, all of which can be derived from the general energy equation of Gillilandl as was pointed out by Mitchellet al in 1954'and more recently by Rose and Sullivan. If the exponent of the equation dE-x-"dx is assigned values of 2,1, or 3/2, one obtains by intergration between suitable limits, the equations of Rittinger, kick,' and Bond,' respectively. Other investigators prefer to let the exponent be a variable parameter. To help resolve the controversy, the Allis-Chal-mers Research Laboratories set up a series of carefully controlled experiments in which the level of energy input required to induce the comminution of a single particle by slow compression loading was very accurately measured. The energy input requirement, in conjunction with the size analysis of the fragments produced at fracture, yielded an accurate energy-product size relationship for the conditions studied. APPARATUS The experimental apparatus was designed to apply a compressive load on opposite sides of an "ideal particle." Spherical shapes were chosen, because point contact loading is typical of the mechanics of conventional crushers. The bulk of the experimental data was obtained with glass spheres because glass is a fairly homogeneous, brittle material for which the properties follow definite statistical distributions. The spheres ranged from 1/8 to 1-in. diam. The compressive load was applied to the specimen at a uniform rate by a loading mechanism (Fig. 1) which acted through a system of levers. The uniform rates, ranging from 100 to 100,000 lb per min, were obtained by metering water into a bucket suspended at the end of the secondary level. Point contact was made with the sphere through tungsten-carbide platens. This latter material is extremely hard and has a high modulus of elasticity, thereby having a minimum of distortion when loaded. The actual load on the sphere was measured independently of the lever system by a load cell, Fig. 2, which was designed so that the voltage output of the load cell would be proportional to load. The deformation of the specimen was indirectly measured by a pair of transformers which were attached to opposite edges of the upper platen. The cores of the transformers, which were attached to the lower platen, moved relative to the transformer so that the voltage output was proportional to the deformation of the sphere-platen system. The load was plotted against the deformation on an X-Y recorder. The area under the curve, as shown on Fig. 3, was proportional to the energy input of the

Jan 1, 1961

By J. A. Singmaster

A REPORT that it did not pay to use present-day galvanized iron on account of the short life of the material, accompanied by proofs of the state-ment in the form of a tabulated history of the first costs of various kinds of building materials and their main-tenance expense, started an investigation of modern galvanized products. At the very outset it was apparent that our experience with galvanized products was by no means unique. Correspondence with the State Agricultural Depart-ments, the Agricultural Experiment Stations, the County Agents and State Granges all over the United States brought a mass of complaint on this same score. Visits to large buyers of galvanized sheet and wire revealed the same condition coupled with an ever-increasing use of substitutes for galvanized iron. We believe, therefore, that the title of this article is fully warranted by the experience of the consuming public. A study of the proceedings of the various societies having to do with the testing and use of sheet iron and steel products revealed a tremendous amount of work on the life of the base metal itself. Great stress was laid on differences in life of various types of iron and steel, the difference amounting at best to months rather than years. Very little recent attention has been paid to a study of the life of the zinc coating and the causes of its present-day lack of durability. There have been some real exposure studies published, how-ever, which show that the weight of the zinc coating determines the protection afforded by the galvanizing, which is of far greater influence on the life than the base-metal composition. An interesting paper was published by the Phillipine Journal of Science in 1916, entitled: "Galvanized Roofing in the Phillipines," a contribution from the Bureau of Science of the Phillipine Island Government. The author, Mr. Arguelles, found on 18 old galvanized sheets, after from 30 to 35 years' exposure, from 2.3 to 4.1 oz. of zinc per sq. ft. of sheet and sums up the study by saying: Of the various factors influencing the durability of galvanized iron which have been studied with a view towards accounting for the difference in behavior of old and modern sheet, it appears evident that the greater weight of zinc per unit of area on the former accounts for the greater durability.

Jan 10, 1922

By Malcolm F. Hawkes

AUSTENITE grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, machinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to provide knowledge of the grain-size -characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstructures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The problem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will be considered first. More than So commercially produced cast steels representing a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules; namely, one hour at 1550°F, one hour at 1700°F, and six hours at 1700°F. The list of steels and results obtained on them will be found in the appendix. (See page 21.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT METHODS SUITABLE FOR DETERMINING AUSTENITE GRAIN SIZE AFTER HEAT- TREATMENT AT ORDINARY TEMPERATURES AND TIMES It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1947

By R. P. Rothwell

AT this our first meeting I beg to call the attention of the members of our Institute to what is certainly a question of the greatest possible importance to the industries we represent; and more particularly to the welfare of the coal and iron trades : I refer to the enormous waste of coal in mining and in its preparation for market, as now practised in our anthracite coal-fields. It is a fact which many of you can certify to, that we are wasting fully one-ha f of all the coal in the veins we are now working, and there are cases, which might be mentioned where this proportion, immense as it is, has been greatly exceeded. The popular belief that our deposits of anthracite coal are "practically inexhaustible," is very far from being founded on facts. On the contrary, supposing the present rate of increase in the production to be maintained, it is probable that a maximum yield for our coal-fields would be attained in about fifteen years ; there are in fact some of our smaller basins where the principal veins are nearly exhausted and the production has already attained its maximum. There are others, again, where the depth attained-and it must be borne in mind that we commenced working at the surface outcrop-moderate though it is (scarcely ever reaching eight hundred feet), has so increased the cost of mining as to imperil the capital invested, and though it requires but little foresight to predict the time when the difficulties of mining will be very considerably increased by reason of the greater depth, greater quantity of water, fire-damp, and other fruitful sources of cost, yet, ignoring these recognized facts, we continue to waste more than one-half of the coal where it is obtained with the least danger, expense, and trouble, that is, near the surface-either above water-level or at a moderate depth below it. The inspection of almost any accurate mine map will satisfy you that, on an average, we leave fully one-third. of the coal in the ground as pillars to support the roof; in some places more than one-third thus remains, while it is very rare that less than one-quarter is left. In almost every case this coal is absolutely lost, for it will very rarely pay to reopen gangways and lay roads to it after that portion of the mine has been abandoned. Is it necessary in all cases to support the roof, and where it is, may not some artificial

Jan 1, 1873

Geostatistics originated as an application of a classical statistical concept, multivariate linear regression, to the solution of a practical problem, estimation of reserves in the South African gold mines. In this respect, geostatistics should only be considered as one statistical method among many that can be used to evaluate mineral deposits. R.F. Shurtz has studied possible applications of power spectrum analysis to the same problem, and these studies may result in future improvements over the presently accepted geostatistical methodology. The intention of R.F. Shurtz's paper, as stated by the author, is to "relate geostatistical doctrine to classical statistical and mathematical concepts." However, in this comparison the "geostatistical doctrine" appears to include only the simplest among the geostatistical concepts advocated by G. Matheron, while "classical statistical and mathematical concepts" are limited nearly exclusively to power spectrum analysis. The author attempts to compare the two methods, and to prove the theoretical superiority of power spectrum analysis. Unfortunately, a number of errors and incorrect statements are made concerning both the theory and application of geostatistics, which invalidate the comparison and the conclusions drawn from it. The errors made in this comparison are understandable since few scientists can claim to have expertise in two theories as diverse as those compared here. In many respects, this paper is reminiscent of polemics which occurred 15 to 20 years ago when geostatistics and trend surface analysis were compared. Each method has its own merit and limitations, and none can claim absolute superiority. The most misleading statements found in R.F. Shurtz's paper are: The definition of the semivariogram given on page 1923 is incorrect. If the maximum difference between two assays is 1, the maximum value of the semivariogram is not 1, as stated, but 0.5. The comparison of geostatistics and linear regression made in the section entitled "Insufficiency of Classical Statistics?" is not valid. The semivariogram of the sample values given in Table 1 (page 1919) has a parabolic shape indicative of a linear drift. When such a semivariogram is observed, the simplest method of geostatistical estimation (linear kriging with unknown mean) is not applicable. Universal kriging must be used that takes trends into account. On page 1921 it is stated that the use of trends "is officially disparaged in geostatistics." Again on page 1924 mention is made to "Matheron's commitment to random process (intrinsic) models and his present categorical rejection of deterministic (trend) models for mineral deposit evaluation." Indeed, from articles published by geostatisticians in the 1960s one could infer that geostatistical methods are not compatible with the presence of trends. However, even the simplest

Jan 1, 1984

By Sherwin F. Kelly

The Geophysics Education Committee was organized in 1938 and presented its first report at the A.I.M.E. annual meeting in February, 1939, at a session held jointly with the Committee on Geophysical Methods of Exploration. REPORT OF 1939 The first task the Committee set itself was to find out in which universities the subject of geophysics was being taught, and the manner in which such instruction was given. A questionnaire was drawn up and sent out to 147 universities in the United States, Canada, and abroad. Of these 100 replied. Their answers were then tabulated and analyzed, yielding the information summarized in the following pages. Two universities, Colorado School of Mines and St. Louis University, actually maintain departments of geophysics, while 3 Canadian and 31 American universities give courses on the subject. In other institutions, 45 in the United States and 5 in Canada, more or less extended reference is made to geophysics in lectures on other subjects. Altogether, there are at least 86 universities in the United States and Canada at which students may obtain instruction of some kind in geophysics. To enter the courses in geophysics given by 33 American universities, certain prerequisites are demanded, varying with the level at which the subject matter is treated. In analyzing the prerequisites, some assumptions had to be made: one year of college mathematics was taken to mean up to, but not including, calculus, while three years was presumed to embrace a course in differential equations. On this basis, 16 per cent require only elementary college mathematics, 40 per cent require differential and integral calculus, and 31 per cent require differential equations. A few demand even more advanced mathematics, while some list no prerequisite mathematics beyond high school. Evidently a student contemplating the study of geophysics should ground himself in calculus and differential equations. In physics, similar assumptions have been made as to time required in the subject. All of the universities giving geophysics require their students to take physics first, and 34 per cent require a standing in

Jan 1, 1940

By Sherwin F. Kelly

The Geophysics Education Committee was organized in 1938 and presented its first report at the A.I.M.E. annual meeting in February, 1939, at a session held jointly with the Committee on Geophysical Methods of Exploration. REPORT OF 1939 The first task the Committee set itself was to find out in which universities the subject of geophysics was being taught, and the manner in which such instruction was given. A questionnaire was drawn up and sent out to 147 universities in the United States, Canada, and abroad. Of these 100 replied. Their answers were then tabulated and analyzed, yielding the information summarized in the following pages. Two universities, Colorado School of Mines and St. Louis University, actually maintain departments of geophysics, while 3 Canadian and 31 American universities give courses on the subject. In other institutions, 45 in the United States and 5 in Canada, more or less extended reference is made to geophysics in lectures on other subjects. Altogether, there are at least 86 universities in the United States and Canada at which students may obtain instruction of some kind in geophysics. To enter the courses in geophysics given by 33 American universities, certain prerequisites are demanded, varying with the level at which the subject matter is treated. In analyzing the prerequisites, some assumptions had to be made: one year of college mathematics was taken to mean up to, but not including, calculus, while three years was presumed to embrace a course in differential equations. On this basis, 16 per cent require only elementary college mathematics, 40 per cent require differential and integral calculus, and 31 per cent require differential equations. A few demand even more advanced mathematics, while some list no prerequisite mathematics beyond high school. Evidently a student contemplating the study of geophysics should ground himself in calculus and differential equations. In physics, similar assumptions have been made as to time required in the subject. All of the universities giving geophysics require their students to take physics first, and 34 per cent require a standing in

Jan 1, 1940

By Joseph W. Leonard, T. S. Spicer

INTRODUCTION Reasons for Thermal Drying The continuing increase in the percentage of minus %-inch coal produced as a result of the increased use of mechanical mining methods has, over the years, tended to shift considerable portions of the work of producing saleable coal to the fine coal cleaning section of the preparation plant. Because a given weight of fine coal will contain substantially greater surface area than an equivalent weight of coarse coal, it follows that, when subjected to wet cleaning processes, the fines will absorb and retain consider- ably more moisture than coarser fractions. Increased moisture pickup in the finer sizes complicates fine coal cleaning since beneficiation may not be limited to the removal of ash and sulfur but often must be expanded to include the additional step of thermal drying to remove excessive moisture. Thus, water which provides the medium for cleaning fine coal is in itself detrimental and, like ash and sulfur, reduces coal quality. Removal of surface moisture by drying is done for one or more of the following 1 reasons: (1) To avoid freezing difficulties and to facilitate handling during shipment, storage and transfer to the points of use; (2) to maintain high pulverizer capacity; (3) to reduce heat loss due to evaporation of surface moisture from the coal in the burning process, thus increasing heating efficiency; (4) to improve the quality of coal used for special purposes, such as in the production of coke, briquettes, and chemicals; (5) to decrease transportation costs; and (6) to facilitate dry coal-cleaning processes. Because benefits to coal transportation and utilization are the most common reasons for thermal drying, the following sections will examine these areas in greater detail. Benefits to Transportation Initial benefits from drying are the reduction of shipping costs from the mine to the point of utilization since more coal can be concentrated into a given weight of product when worthless moisture is removed. Non- combustible~ such as water and mineral matter in railroad shipments of coal are billed the same as coal at $3.32 per ton, according to the recent average costs. Savings of 10 to 20 dollars from drying on the shipment cost of each 50 to 60 tons of coal contained in a typical railroad car is common. Savings on coal shipments from individual mines which result from coal drying can be expressed in terms of hundreds of thousands of dollars and more each year. For example, a reduction of shipping charges of only 5 percent on one million tons per year would mean a savings of 166,000

Jan 1, 1968

By B. L. Averbach, M. Cohen

THE PROBLEM MANY hardened steels contain significant quantities of retained austenite even in cases where the carbon and alloy contents are low. In fact austenite has been detected in plain carbon steels containing as little as 0.50 pct carbon.1 Although the austenite may not be visible metallographically it causes definite dilatometric and magnetic effects during subsequent tempering or subatmospheric cooling.1,2,3 Therefore if the reactions which hardened steels undergo during later treatment are to be understood in quantitative fashion it is most essential to have some kind of absolute analysis for the austenite content in hardened steels. Once this analysis has been made, the austenite transformations can be followed precisely by observing such sensitive phenomena as changes in length or in magnetization but the latter techniques can only determine differences in the amount of retained austenite and usually an independent method must be found to put these differences on an absolute basis. In certain instances the microscope can be used advantageously to determine the percentage of retained austenite. The quenched sample is tempered to "darken" the martensite with minimum decomposition of the coexisting austenite, and then is polished and etched in the usual fashion. If the austenite is clearly distinguishable from the tempered martensite and other possible constituents its volume percentage can be measured quantitatively by point counting or lineal analysis.4 Such microscopic methods, however, depend on the etch being sufficiently discriminatory. In fairly coarse structures, if the austenite content is greater than 10-15 pct, there is probably little smearing of the etch, and point counting or lineal analysis seems to be quite accurate. On the other hand if the structure is difficult to resolve, as in commercially treated fine-grained steels which contain less than 10-15 pct retained austenite, the latter may be completely obliterated by the dark etching martensite or it may appear disproportionately low as the interfaces between the two constituents become difficult to distinguish. Another disadvantage of the metallographic method is the need for "darkening" the martensite and hence the determination cannot be applied to as-hardened steels. The required tempering may spoil the structure for other tests or may even remove a small part of the austenite which is being sought. X ray methods hold more promise for covering the range under 15 pct retained austenite. Although austenite and martensite in the hardened steel may be chemically identical, their crystal structures and lattice parameters differ, and the intensity of an austenite diffraction line is some continuous function of the percentage of re-

Jan 1, 1948

By A. J. Shaler, J. Prieto Isaza, J. Wulff

Tantalum metal has a number of unique properties which give it widespread application in modern technology and in research. In electronic apparatus involwing high temperatures in vacuo some of the refractory metals 6ecome brittle. Tantalum retains its ductility at elevated temperatures, and this property, together with its low vapor pressure and its ability to absorb gases, make it important in this field. Its chemical inertness in the presence of acids, halogens, and other corrosive media, makes it useful in chemical apparatus and in neuro and orthopedic surgical applications. As an addition to tungsten carbide in steel-cutting grades of cemented-carbide tools, the carbides of tantalum and of its sister element colum-bium have found considerable use. The present-day method1 of manufacturing tantalum is to sinter a powder compact of the metal in vacuo. Because tantalum-columbium alloys are difficult to work and since tantalum ores almost always contain columbium, the two metals must be separated chemically, the products of the separation being generally in the form of potassium tantalum fluoride and potassium columbium oxyfluoride. These salts are used in fused-salt electrolytic baths from which coarse metallic powder is deposited as a sponge at the cathode. Finer powder can be made from the coarse product or from tantalum scrap by first submitting it to an embrittling heat treatment in hydrogen and then crushing it. The fine hydrogen-containing powder may subsequently be degassed in vacuo at a high temperature. Prompted by the success of others2,3 in the magnesium reduction of titanium and zirconium halides; one of the authors undertook4 an investigation of the thermochemistry of the reaction between solid magnesium and gaseous tantalum penta-chloride, a subject which had not previously been studied. He found that the heat of formation of tantalum pentachloride is approximately 364,250 cal per mol at temperatures lower than the melting point of magnesium. A value of 83 units was found for the standard entropy at these temperatures. With these values, it was shown that magnesium and tantalum pentachloride are capable of reacting exo-thermically at temperatures less than the melting point of magnesium, and that no great violence is to be expected when these substances are heated together. The exothermic nature of the reaction indicated that the Drocess should be efficient and should not require much externally applied energy. Tantalum pentachloride is not commonly made commercially, and any process using it therefore involves the subsidiary problem of producing and handling this substance. A series of experiments was carried out in which dried chlorine saturated with carbon tetrachloride was passed over heated tanta-

Jan 1, 1949