Search Documents

By J. E. Murphy, L. A. Walters, F. H. Nehl, G. B. Atkinson

The US Bureau of Mines investigated the selective electrowinning of Ag and Au from cyanide solutions contaminated with Cu with the goal of decreasing the amount of Cu codeposited. Decreasing Cu codeposited will reduce refinery costs. Direct current was applied to the cell in pulsed and square wave voltages at 0.7 A h/150 mL of solution. Times tested for each cycle ranged from 1 to 10,000 msecs. Graphite, lead and stainless steel were evaluated as electrode materials. Square wave electrowinning at 70°C (158° F) gave the best separation of Ag and Au from Cu. Applying 2.5 V during the duty cycle, 0.0 V the rest of the period, a duty cycle of 10% to 30%, and a period of 100 msecs to 1000 msecs gave the following results: Ag concentrations decreased from 34 µg/mL to 0.1 µg/mL. Au concentrations decreased from 54 µg/mL to 0.2 µg/mL and Cu concentrations remained almost constant at 560 µg/mL.

Jan 1, 1995

By N. Damiano, C. Zhou, R. Jacksha, J. Srednicki

Modern electronic devices and systems used to enhance miner safety and health are becoming commonplace in underground coal mines. The ability for these devices and systems to function properly in the presence of electromagnetic emissions from other electronic and electrical devices and systems is not entirely understood. To investigate potential electromagnetic compatibility issues of critical mine electronic devices and systems, researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting surveys of electromagnetic emissions in underground coal mines. This paper presents the measurement system, methods, and results of electric field electromagnetic emission surveys conducted in three underground coal mine environments in the frequency range of 10 kHz to 1000 MHz. The survey data show that in some environments electric field electromagnetic emissions in underground coal mines approached or slightly exceeded limits as defined by other industrial sectors.

Mar 2, 2022

By R. Berton, M. Walden, S. Melberg, N. Rocco

Recent tailings dam failures around the globe have influenced many mining industry regulators to reassess their requirements for the numerical modelling of tailings dam failures. This type or forward modelling is associated with overarching uncertainties as the model cannot be calibrated against a physical result. Dam breach analyses that meet the requirements of current industry standards and guidance typically begin with identification of credible failure modes and selection of appropriate topographic data set to represent the study area. The breach parameters and the volume of tailings released are then determined using available methodologies and empirical relationships. Subsequently, when the breach hydrograph is developed and the hydrology of stream networks are complete, the runout simulation is implemented. Due to the uncertainty involved in the process, sensitivity analyses are recommended to quantify variations in model inputs on the inundation extent and the flow characteristics. This paper outlines some common methodologies utilized for development of dam breach models, summarizes associated uncertainties with these methodologies and inputs, and provides guidance on how sensitivity analyses can address a wide array of uncertainties inherent in tailings breach analyses. This paper provides an understanding of how selecting appropriate breach parameters can result in reasonably conservative inundation extents consistent with the identified credible failure modes.

Mar 2, 2022

By Ning Wang, Tengfei Guo, Wanyan Li, Hanjie Wen, Hannian Gu, Zehai Li

Red mud has been reported as a potential resource for lithium. To investigate the leaching behavior of lithium, a lithium-rich red mud was neutralized with hydrochloric or oxalic acid and then leached with acetic acid. When red mud was neutralized using dilute hydrochloric acid, about 58 to 60 percent of lithium was leached with 25 percent acetic acid at 95 °C for 60 min, while more than 95 percent of sodium and 85 percent of calcium were dissolved in the leachate solution. When oxalic acid was used to neutralize red mud prior to acetic acid leaching, lower lithium leaching efficiencies of about 42 to 47 percent were observed. Nevertheless, these leaching efficiencies of lithium were close to that of calcium and much higher than those of sodium under the same conditions. In this study, 25 percent (v/v) of acetic acid at 85 °C for 60 min was demonstrated to be the optimum conditions for lithium extraction from oxalic acid-neutralized red mud using acetic acid. The results are useful and of interest for lithium recovery and purification from red mud.

By Michael J. Mankosa

Increased emphasis has been placed on recycling consumer and industrial waste products. This trend has created a new industry that is focused on recovery/ separation of byproducts from waste material. As a result, interest has increased in the development of separation systems designed for the recycling industry. Much work has been done in this area. However, existing techniques developed for minerals beneficiation are often ignored. An example of is the foundry industry. There are currently more than 3,000 foundries in operation throughout the United States. Each consumes between 9 and 900 t/d (10 and 1,000 stpd) of sand for mold production. Either silica, chromite or zircon is, used in various combinations with chemical or clay binders. After casting, the sands are typically discarded into a landfill. This practice has become an environmental concern, especially the disposal of chromite and zircon. Silica sand is not environmentally sensitive. But it is used in greater abundance (6 to 7 Mt/a or 6.6 to 7.7 million stpy)and thus has prohibitive haulage and landfill costs. Current technology for sand reclamation involves thermal treatment to remove residual binders followed by dry mechanical attritioning (Leidel, 1993; Klein, 1994). This approach results in high losses due to fines generation and high costs associated with thermal treatment. As a result, this approach has shown only limited success. Stringent regulations are also affecting the disposal of secondary materials, such as plastics and metals. This is particularly true for the ferrous and nonferrous scrap metal industry. It plays a major role in industrial recycling of steel, aluminum and copper. Applications such as wire recycling present challenging problems since a hazardous byproduct (plastic insulation) is generated by the recycling.

Jan 1, 1997

By Robert B. Crookston

Oil from shale has been produced in foreign countries for more than a hundred years; however, except for short-lived, small operations, no commercial quantity of oil shale has yet been produced in the United States. Efforts to develop a viable oil shale process have been underway domestically for many years. At the present time, with the need for energy so urgently upon us, almost a dozen development ventures are underway or planned in Colorado and Utah. Of these several ventures, only Colony Development Operation has completed the development, testing and design of a ready-to-go 50,000 barrel per day com¬mercial project. Colony is a joint venture of the Atlantic Richfield Company, Ashland Oil Company, Shell Oil Company and The Oil Shale Corporation, more commonly known as TOSCO. TOSCO is the exclusive licensor of the TOSCO II retorting process and other oil shale technology, which includes mining, crushing and spent shale disposal techniques. This paper will deal, however, with only the materials handling aspects of the commercial oil shale operation. Oil shale handling for this infant industry is unique in that an understanding of the physical characteristics of the ore and the demands on material handling to the plant must he understood. Colony Development has completed ten years in the research and development of techniques and processes for mining, crushing and retorting raw oil shale and the disposal of spent or processed shale. A great deal has been learned about oil shale, in many cases confirming our intuitive analyses and the work of others, but more specifically we have brought it all together to a point where equipment performance and the specifications have been established and a design for the first commercial plant is now mature.

Jan 1, 1975

By E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT Leadership is a critical component to an organization’s safety culture and influences the ways that health and safety is enacted on site. Therefore, it is not surprising that improving leadership will also improve safety. Worker perceptions of management practices are shaped through unique leader-employee interactions over time. However, few details are known about the communicative support (i.e., emotional, informational, and tangible) offered by supervisors and its impact on miners’ perceptions and performance. Using pre and post-interview data with 20 supervisors and 48 workers during six-week interventions, researchers identified positive and negative instances of supervisor support and its implications on worker performance. This paper highlights the common support tactics offered by supervisors and desired by workers to help practitioners identify ways to improve their safety culture and subsequently, the proactivity and compliance of their workforce. INTRODUCTION Supervisory leadership is a critical component to the effective implementation of an organization’s health and safety management system (HSMS). Specifically, supervisors serve as representatives of an organization and their actions are indicative of the organization’s safety culture (Eisenberger et al. 1986). Senior management has been shown to serve as a frame of reference for guiding safe behaviors in the workplace (Mearns et al. 1998) and, more recently, research has related supervisory enforcement to workers’ safety compliance (Petitta et al., 2017). Therefore, it is not surprising that by improving leadership, perceptions of management and subsequent safety outcomes are likely to improve as well (Zohar, 2002). Perceptions of management are shaped through unique leader-employee interactions over a period of time (Hofmann and Morgeson, 2004, 1999). How these unique interactions impact worker performance, however, remains unexamined. As a result, understanding how supervisor-employee relationships operate in high-risk environments is unclear (Mirza and Isha, 2017; Denis et al., 2010). A starting point to better recognize the idiosyncrasies of these relationships is by way of examining the communicative support offered by front-line management and received by industry workers. To this end, this paper uses pre- and post-interview data to study the communicative aspects of supervisor-employee interactions at mine sites. The analysis uses a social support framework to identify positive and negative instances of supportive communication. From interview data with 20 managers and 48 mineworkers, data emerged that shows how supervisors’ unique types of support contribute to workers’ perceptions, motivation, and follow-through of safe work behavior.

Jan 1, 2019

By Y. Lizotte

The purpose of this paper is to describe a stochastic simulation program used to assess several dispatching rules applicable to small scale computerized systems for optimizing truck/shovel productivity. The system studied is semi-automated with a dispatcher communicating instructions by two-way radio. The simulation program is structured on an advance clock approach which enables the insertion of dispatching rules at various points in the haulage net- work. The rules tested include minimize shovel idle time, maximizing immediate truck use and assigning trucks to shovels to meet specific production objectives. A variation of the traditional "Match Factor" is implemented to maintain fleet balance throughout the shift. A mine case study demonstrates how the dispatching rules increase productivity of such semi-automated dispatching systems. Practical problems involved in the implementation of small computerized dispatching systems are also discussed.

Jan 1, 1986

By C. D. Kuchera

Ore crushing facilities at the Phelps Dodge Morenci Reduction Works became operational in January of 1942. This plant, with a capacity of 25,000 tons per day, was part of a project started some five years earlier with development of the Morenci Open Pit Copper Mine. In the following year, World War II's heavy copper demands prompted an 80% expansion in concentrating capacity to 45,000 tons per day resulting in a doubling of the secondary crushing plant. In the late 1950s and early 1960s, grinding capacity was again expanded to the present 60,000 TPD. This time the then 20 year old crushing plant was obliged to meet a 20% increase in production demand with no additional equipment. The ore, principally a medium hard monzonite porphyry, is dumped from 40 yard rail cars into an ore pocket over the primary crusher at a rate of approximately one car per minute. The primary crushing flowsheet, Figure 1, has remained essentially unchanged over the years. Equipment consists of a 40 by 16 foot grizzly set on a 40° incline and having 6" openings, a 60" gyratory crusher nomin¬ally set at 62" + 1" on the closed side and two 72" by 38' panfeeders which load crushed ore and grizzly undersize at a rate of 4,000 tons per hour onto a twin 54" belt conveyor system for delivery to the coarse ore bin. Ore is distributed across the bin by two single side discharge tripper cars. Bin capacity is extremely limited at 23,000 tons of which only 12,000 is available or "live".

Jan 1, 1975

By T. Y. Yan

O2, NaCl03, H202, NaOCI and Ce+4 have been examined as oxidants in an alkaline carbonate system for uranium in situ leaching. The South Texas and New Mexico ores contained up to 2.6 meq/g of reducing compounds that consume oxidants in the leaching operation. Leaching rates did not increase linearly with the oxidation potential of the oxidants. A mild oxidant can be used to maximize uranium oxidation selectivity and oxidant efficiency. 02 can oxidize most of the uranium mineral with an adequate rate and high oxidant efficiency.

Jan 1, 1993

By J. L. Hoover, P. W. Conrad, J. Downey, S. Parrow, S. Rosenthal

The goal of the drill bit consumption study was to develop an equation(s) based on various components that affect drill bit wear and use that equation(s) to estimate the consumption of bits during production drilling. Drill bit data from various geographic locations were compiled and used to develop linear regression equations using the Microsoft Excel software package. Multiple drill bit consumption equations were developed and statistical analysis was used to verify the accuracy of those equations. The equations will allow mining companies to more accurately forecast drill bit consumption when evaluating new mine properties. This capability becomes increasingly beneficial to forecasting as the cost of consumables increases.

Jan 1, 2012

By R. O. Y. Breese

Perlite is a hydrated acid volcanic glass that has been derived from the alteration of obsidians through incorporation of water into the silica structure. It is distinguished from other members of the water-bearing natural glass family by total water content, characteristic fracture and luster. The distribution of major occurrences worldwide is associated with silicic Tertiary through early-mid Quaternary volcanics related to plate movement. The No Agua dome and flow complex is one of the most highly studied perlite occurrences in the world. It clearly exhibits lithologic and textural zonations that reflect simple cooling history. Similar features are commonly observed within other perlitized, extrusive glass selvages. This paper briefly discusses current thought regarding geologic occurrence, the hydration process and the modes of origin with special emphasis on No Agua.

Jan 1, 1985

By D. Potter

Freeport Exploration initiated regional reconnaissance exploration programs in Irian Jaya, the easternmost province of the Republic of Indonesia in 1990 (see figure 1). Irian Jaya occupies the western half of the island of New Guinea. Freeport was awarded an initial contract of work which totaled 2.6 million hectares (6.4 million acres) and was subsequently awarded additional?concessions which added 1 million hectares (2.5 million acres). The concessions require work commitments and periodic relinquishments. Due to these relinquishments Freeport?s current land position totals l. 9 million hectares (4.7 million acres).

Jan 1, 1998

By T. Harrison

Surface coal mines in West Virginia are receiving stringent NPDES discharge limits for total recoverable selenium. With limits in the low parts-per-billion range, selection and implementation of proper sample collection and analytical methods are imperative for quality assurance and control and for consistency in results. Given the typical oxidized form of selenium in the water, the low limits and the large and variable flow rates from the watersheds, end-of-pipe treatment is difficult and cost-prohibitive to implement. Discharge locations in the remote and steep terrain exacerbate the problem. To evaluate options for end-of-pipe treatment at a Patriot Coal Corporation surface mining operation in West Virginia, CH2M HILL performed wastewater characterization for a range of key constituents and selenium species at three outfalls for selection and preliminary sizing of appropriate treatment processes. A preliminary evaluation of base and wet-weather flows was done to understand flow variability considerations for discharges. A conceptual evaluation of technologies to treat selenium to permitted levels was conducted in con-junction with order-of-magnitude life-cycle cost estimates.

Jan 1, 2010

By Greg Sanders, Bill Lueck, Michael Gilbert, Mahmood Khwaja

"The city of Minneapolis contracted with CDM Smith to update and provide a conceptual design for improvements to mitigate surcharge flooding in the Central City Storm Water Tunnel System (CCSTS). As a part of the project, CDM Smith conducted a field survey and condition assessment of the existing tunnel system. Information from the survey was then used to update the existing XPSWMM model and develop system wide alternatives.The CCSTS provides storm-water runoff drainage for nearly the entire area of the city’s downtown commercial district. The system consists of deep storm-water tunnels constructed in the St. Peter Sandstone, approximately 21 m (70 ft) below the street’s surface. The primary tunnels comprising the Central City storm water tunnel system are located below Hennepin Avenue, Nicollet Mall, Lesalle Avenue, Marquette Avenue South, 2nd Avenue South, South 5th Street, Washington Avenue South, Portland Avenue South, 2nd Street South, and Chicago Avenue South, as shown in Fig. 1. This network of tunnels conveys the runoff from a 305-acre tributary area that is generally bound by Hennepin Avenue and 1st Avenue North to the east, 12th Street to the south, 4th Avenue South and 7th Avenue South to the west, and 2nd Street South. These tunnels were constructed between 1936 and 1940, except for the Marquette Avenue South tunnel, which was constructed between 1963 and 1964.The CCSTS operates as a gravity flow system. These tunnels were constructed within the St. Peter Sandstone layer of bedrock and emerge from the bedrock at the Mississippi River below St. Anthony Falls. The Central City and the adjacent Chicago Avenue tunnel system converge into a single outfall at the Mississippi River. The runoff discharges from the converged outfall to a side channel of the Mississippi River, called a tailrace, located near the Guthrie Theater. The Minneapolis Division of Surface Water and Sewers provided 32 historic plats detailing the plan and profile of the tunnel system.The tunnel plans show nine different cross-section configurations. Eight configurations within the overall system generally show the same geometric “cathedral” shape with the inside dimensions varying from 1.2 to 1.8 m (4 to 6 ft) in width and 1.8 to 2.4 m (6 to 8 ft) in height. For analysis, these eight configurations were reduced to three configurations with regards to tunnel liner, cross-sectional area and support. For simplicity, the three configurations are described according to the three types of tunnel support used during construction: none required, light timber and heavy timber"

Jun 1, 2019

By Basilio Giurgola, Jeremiah M. Jezerski, Filippo Azzara, Federico Bonaiuti, Russell H. Lutch

The Northeast Boundary Tunnel Project consists of a 23 ft diameter, 27,000 ft long, CSO tunnel, multiple underground connections, and significant surface works within an urban corridor. The NEBT alignment depths range from 60 to 140 ft and includes seven shafts ranging in depth from 77 to 155 ft with diameters varying from about 19.5 to 56 ft, some as in-line connections and others required adits for connection to the main tunnel. This paper focuses on the design and construction of two major underground connections which are the First Street Connector Tunnel and the Mount Olivet Road Diversion Sewer.

Jun 13, 2023

By Daniel Connor, O&apos

The Cal-Sag Relief Sewer is a 2.6 m (8 ft 6 in.) diameter 9.1 km (5.7 mile) rock tunnel bored in dolomite for the Metropolitan Sanitary District of Greater Chicago. Included in the project are 18 shafts varying in depth free 70 m (230 ft) to 41 m (135 ft). This paper discusses how Healy/Vanessa reduced costs by eliminating conventional hand excavation by hoisting muck from a high production Robbins TBM (Tunnel Boring Machine) through small diameter drilled shafts and using a trailing rail-utility backup system.

Jan 1, 1985

By Pedro Pablo Vasquez Coronado, Victor Octavio Tenorio

"Productivity in openpit mines depends on the observation and adjustment of critical phases of operation. As one of the most expensive activities in openpit production, optimization of the load-haul-dump cycle becomes a critical aspect to address. Using simulation techniques and an ad hoc methodology for analyzing the key performance indicators (KPIs) involved in the production cycle, it is possible to compare actual performance and ideal operating conditions and develop an alert system when operating conditions are subpar with the expected production standards.Study objectivesThe purpose of this work is to implement a methodology for optimizing the haulage cycle by identifying and adjusting the factors that affect the cycle time performance. The methodology includes the implementation of an alert system emitting warning messages when one or several trucks are idle, or when the time of completing production tasks is falling outside a predefined value. This alert is compared with predefined KPIs and is used to determine corrective actions.The alert will:• Demonstrate the benefits of time analysis and how this affects the productivity results in the mining process.• Demonstrate the utility of KPIs in the extraction of ore and waste and how they help to identify equipment performance.• Develop software interfaces to visualize the alert system in order to increase awareness in the operations supervisor.• Make recommendations for future applications that can help improve the productive process of an openpit mine.Problem statementTransporting material in openpit mines may require the utilization of high capacity equipment, which also represents an elevated cost per hour. A supervisory system that controls the adequate distribution of trucks and shovels by providing the operational status of each unit shall contribute to increase productivity while subsequently reducing operational costs. Nevertheless, there is an issue with certain dead times such as queue trucks for loading, trucks waiting to be loaded and other delays. This creates inefficiencies in fuel consumption and energy utilization.For the identification of delays, a contextbased system could be required in order to help optimize the haulage cycle time by controlling delays in loading, haulage and dumping. After applying this methodology, efforts were focused in correcting out-of-standard performance values."

Jan 1, 2015

By Armin C. Supp

Since 1975, about a dozen high capacity flotation plants have been installed in the Ruhr district. Depending on the size of the preparation plants, the design capacity of the flotation section is between 100 - 150 t/h. The flotation units generally comprise rougher and cleaner stages in which 5 to 6 or 4 to 5 agitators respectively are arranged in line. The unit volume allocated to each agitator is up to 16 m3. The type of flotation machines, the design of these plants and their instrumen¬tation and control equipment are described in detail. The run of mine coal in the Ruhr district is characterized by a wide variety of the volatile matter. Generally, a distinction must be made between coals with more than 30 - 35% V.M., which are preferably used in power station, and coal with lower V.M. content, which are preferably used as coke-oven feed. The difference between these coals in respect to grain-size distribution, ash cotent and flotation properties will also be described in detail.

Jan 1, 1985

By Gary Nash

While there could be as many directions on regulations as there are viewpoints surrounding the asbestos controversy, there are a few basic criteria that generally will influence government thinking, namely: - their definition of the problem to be regulated, - their interpretation of the scientific evidence available to them, and - their sensitivities to the views of, and the implications for, various interest groups in society. Clearly, different assessments of these criteria by various governments will lead to differing regulatory regimes. The consequence, of course, is a patchwork of non-conforming regulations among nations, with all that thin implies for the distortion of international trade and the unsettling of international relations. I would therefore argue that when governments are examining regulatory action, they should explicitly take into account their common interests in stable and cordial international relations, and when possible, efforts should be made to ensure that movement on regulation is at least, in principle, in accord with the general views of the international community.

Jan 1, 1984