Search Documents

By P. L. Placek

Correlations were made on experimental data for four New Mexico ore series to determine relationships between ore grade and uranium extraction during leaching operations. Such relationships provide information needed to predict the long-range supply of minerals to meet national economic and strategic needs. Results show that other ore constituents and gangue materials in addition to uranium grade influence uranium extraction. In general, tailing grades decrease and uranium extraction increases as both H2S04 and NaCl03 concentrations increase. Terminal emf and terminal pH also were studied. Similar trends appeared for all ores; however, specific combinations of results also were observed for individual ores and ore series. Experimental results indicate that uranium extractions are higher for lower uranium feed grades than predicted by other estimates. Three factors--uranium feed grade, H2SO4 concentration, and NaC103 concentration--were used to design factorial experiments for each ore series. Four additional feed assay factors--V205, Fe, C02, and CaO--were included in regression equations to account for some of the variation in data. The three factorial factors are represented in the regression equations by linear and exponential terms of the form D i'1*G i + Di,2 *e Di, 3*Gi. The four additional assay factors are represented by linear and squared terms of the form Di,*Gi + Di,2*eDi3*Gi. where the Di, ,J are coefficients, the Gi are factors, and the symbol * represents multiplication in computer notation. The interactions of the factors are represented by products of the nonlinear terms for all pairs of the factors.

Jan 1, 1981

By A. A. Afshari, D. G. Frazer, C. F. Stanley

"INTRODUCTIONThe primary function of the lung, i.e. gas exchange, occurs in peripheral units termed alveoli• Diagnosis of lung dysfunction ls therefore dependent on techniques to evaluate the status of the peripheral airways. Since these airways and alveoli are very small, it is difficult to determine directly how they function or how the function is changing due to disease. Yet this unde1·standing is critical to the design of instrumentation to detect early changes in lung function due to disease.An interesting hypothesis describing one aspect of small airway function has been proposed by Frazer (1) as gas trapping due to the formation of menisci in the airways. An additional study (2) proposes that the breaking and possibly the formation of these menisci could generate lung sounds, i.e. crackles. These lung sounds were recorded by placing a microphone at the trachea of an excised rat lung. The lung was degassed and then inflated and deflated. At points along the path of inflation, lung sounds were recorded. However, determination of the origin of the sounds was not attempted due to the difficulties induced by contacting the lung st1rface with a microphone.The purpose of this paper is to describe a non-contacting, whole field technique to monitor and describe the movements of the lung surface during inflation - deflation cycles.HOLOGRAPHIC INTERFEROMETRYHolographic interferometry is a full field, non-contacting and non-destructive technique that measures deformations of an object with a sensitivity in the order of the wavelength of light. A laser beam is split, with one beam reflected from an object and the other used as a reference beam. Both beams combine to produce a hologram of the object on a photographic plate. The process utilizes the concepts of interference, i.e. the two wave amplitudes will add at the points where the difference in optical path lengths over the exposure period is zero or a whole number of wavelengths and will subtract at other points."

Jan 1, 1989

By C. W. Owings

Two problems perplex many coal-mine operators and employees. Is coal-mine dust harmful to breathe; and, if so, is it possible to keep the concentration below the danger point? The medical profession is not unanimous in its opinion of the danger of breathing bituminous-coal dust, but there appears to be ample and increasing evidence that coal-mine dust can be harmful if breathed in large enough doses for long periods. The question of controlling the dust at the point of formation is still unanswered in the minds of many in the mining industry. However, results of limited studies conducted by the Bureau of Mines in 9 bituminous-coal mines indicate that a full-shift average exposure of workers should not exceed about 20 million dust particles per cubic foot of air (m.p.p.c.f.) and that concentrations can be held within this limit without too much difficulty. Furthermore, these studies indicated that an exposure in the neighborhood of 40 m.p.p.c.f. should not be exceeded for an individual operation and that it is possible to hold within this ceiling.

Jan 1, 1957

By R. Van A. Mills

[In previous contributions** the writer has called attention to important relations that faulting bears to the migration and accumulation of oil end gas. It has been pointed that favorably situated parts of oil and gas bearing, sands have been enriched by migration art segregation incident to faulting. The escape of water through natural passages such. as fault fissures has induced wide spread hydraulic currents through the beds toward these, points, of diminished pressure and these water currents, plus buoyancy hove contributed largely toward the migration of oil to favorable rock entrapments in the vicinity of the faults.*** The propulsive force of expanding gas has been one of the contributing causes for the hydraulic currents. Paradoxical as it may seem, the escape of gas with entrained oil through fissures has been on important factor In the migration, and accumulation of oil in many faulted areas. Compressed gas is the propulsive force by which oil generally moves to producing wells. It is also one of the propulsive forces by which oil has moved with or even ahead of water under conditions: of differential pressure brought about by faulting.]

Jan 1, 1922

By l.J Prosser

from 1990 to 1996, 16 states reported 92 injuries from falls of roof, rib or face in the more than 90 underground stone mines in the United States (Fig. 1). Missouri, Pennsylvania and Kentucky accounted for 48% of the total number of injuries (Fig.2). Of this total, 11 miners were killed. Of the 11 fatalities, 10, or 91 %, were associated with unrecognized loose or failed rock within the roof beam. Additionally, unrecognized roof beam failures resulted in a majority of the falls of ground injuries occurring in underground US stone mines from 1990 to 1996.

By L. E. Schultze

As part of the Bureau of Mines research program on recovering alumina from domestic resources, methods for extracting iron from aluminum sulfate solutions (obtained by leaching kaolinitic clay with dilute sulfuric ,acid) were investigated. In countercurrent extraction experiments at a l-gal/hr flow rate of aluminum sulfate leach liquor, the iron concentration 'was decreased from 1.4 g/l to 0.01 g/l after four stages of using a primary amine extractant. The iron-loaded amine solution was regenerated in five stages using 3[N] sulfuric acid or in four stages using 6[N] sulfuric acid. The aluminum sulfate solution obtained was suitable for the preparation of alumina meeting cell-grade standards of less than 0.01 pct iron.

Jan 1, 1979

By Ivette E. Torres

World investment 10 all mineral and mining industry sectors is not available. However, partial information available provides some information useful for analysis. Information available in this section covers limited geographic information on investment in the steel industry, limited information for petroleum industry capital spending, and total U.S. foreign investment in comparison to the mineral-related sectors (tables 13, 14, and 15). Annual steel industry investment is available for the European Community, almost all countries within the European Free Trade Association (EFTA), Latin America, and other countries with significant mineral industries, such as Canada, Japan, and the United States. Although information was not available for 1992, data for 1991 indicate that for those countries aforementioned, total investment increased by 8 %. However, investment patterns were very different within the different groups of countries. While the European Community had a net increase of 12 %, dominated by an almost °40 % increase in Germany, EFTA member countries had a 26 % decrease in investment for the same period. Investment in EC countries was almost seven times that of EFT A countries. Japan's investment in the iron and steel industry, by far the largest of those available, almost twice that of the EC and almost four times that of the United States, increased by more than 20 %. In North America, investment in Canada and the United States decreased. Almost all of Latin America decreased investment in the sector. The notable exception was Mexico, with a 60 % increase. Changes in Mexico's investment policies of the recent past, its economic growth, and privatization of its iron and steel industry are some of the reasons for such an increase. The other country covered individually in Latin America, where investment in the iron and steel industry increased, although slightly, was Argentina. This limited information does not allow a comprehensive analysis of global industry trend, which in turn impacts many other mineral commodities, and with the transition in many countries within Europe and Central Eurasia that are now effecting the steel industries of the countries that were members of the U.S.S.R. and its CMEA partners, it is most regrettable that comprehensive and comparable data, both current and historic, on investment in this area are not available.

Jan 1, 1994

By Fred C. Turin, Jasinder S. Jaspal, Alan G. Mayton, William J. Wiehagen

This report describes serious injuries occurring to bulldozer operators working at U.S. coal, metal, and nonmetal mines. The period covered is 1988-97. The data were collected by the Mine Safety and Health Administration (MSHA). A total of 873 injury records are examined. These injuries resulted in 18 fatalities and 31,866 lost workdays. All of these injuries occurred to dozer operators while they were doing common production tasks. An injury classification system was developed to code the narrative information that describes the circumstances surrounding the injuries. Injury records are categorized by activity (task being done), incident result (what apparently happened to the dozer), and operator impact (how the operator was injured). Where information is available, contributing factors are identified. This classification system supplemented the standard injury/illness data classification system compiled by MSHA. The results of the study indicate that, from 1993 to 1997, the number of serious injuries to dozer operators declined by 30%. The reduction in serious injuries was accompanied by a decrease in days lost due to injury. Although the number of reported injuries has decreased, dozer operators being jolted and jarred accounts for the largest percentage (70% of the incidents) and severity (75% of the workdays lost) of serious injuries while operating the equipment. Vertical jars (while backing up the dozer) resulting in injury to the operator accounted for a sizable percentage of jolting and jarring injuries. Working near an edge carries significant risk for fatal injuries. Of 116 incidents where the dozer fell over an edge, rolled over, or fell into a hidden void, 14 (12%) resulted in fatal injuries. In cases where the dozer operator either jumped or was thrown out of the cab in a fall over or rollover, 7 out of 26 were killed. Overall, 80% of the fatalities occurred while working near an edge or hidden void or on a steep slope. Further reductions in injury risk will require more widespread use of seatbelts, field and laboratory research interventions to better assess the effect of alternative engineering (e.g., seat and seat suspension) designs to dampen or isolate the effects of shock and vibration, and continued focus on hazard awareness, recognition, and response.

Jan 4, 2001

By Ronald D. Hill, Elmore C. Grim

Coal-haul and mine access roads are defined as any road constructed, improved or used by the operator (except public roads) that ends at the pit or bench. These roads constitute approximately 10% of the total area directly disturbed by the surface mining operation(l). In some cases, the land disturbed by haul roads exceeds the area included in the mining operation. Studies (2 and 3) of the U. S. Forest Service in eastern Kentucky show that typical contour mining roads exhibit poor alignment, excessive grades, insufficient strength and durability, and poor drainage. Mine roads in other Appalachian- States, particularly where contour mining is practiced, appear much the same as those in Kentucky. Access roads(4) were also found to be a large source of sediment. It is possible that of the sediment that finds its way into the streams as much (or even more) originates from the haul roads as from the mining operation. Most roads are built as cheaply as possible, and good road-building design and practice are ignored. Maintenance schedules are generally inadequate, and upon completion of mining, haul roads are usually abandoned, with little or no attempt made to bed them down(5 ) . Such roads deteriorate very rapidly (Figure 68). Area mining, which is practiced in flat to gently rolling terrain, presents fewer haul road related environmental problems. These roads through necessity are generally well engineered because of the heavy equipment using them, such as 240 ton (217 metric ton) haul trucks. They must have wide beds, good alignment, and adequate drainage to permit coal haulers to run at top speed during all seasons of the year. Excessive dust can be a public nuisance and a driving hazard, and it is hard on equipment. Calcium chloride and sodium chloride have proven to be effective materials for controlling dust. Two applications during the summer when the ground surface is moist at the rate of 1/2 pound per square yard (.26 kilograms per square meter) (3 1 have been suggested. Th4 most common procedure is to keep the roads wet by using water trucks. Sediment that reaches the streams can be traced to one or more of the following five basic phases of haul-road life:

Jan 1, 1974

By Bernard Porter

Differential thermal analysis measurements were used to characterize a phase diagram for the KF-YF3 system at compositions between 0 and 60 mole-percent YF3, A congruent melting point compound was observed at 3KF?YFs, which melts at 965°±5° C and undergoes solid-state decomposition at 725°±2° C. One peritectic and two eutectic compositions are also defined.

Jan 1, 1969

The Determination of Sound Exposures (DOSES) software was developed by the National Institute for Occupational Safety and Health (NIOSH) specifically for use by mine management and safety personnel. DOSES simplifies the record-keeping and analysis associated with time-motion studies and worker noise exposures, making it easier to identify and solve noise problems. The software relies on a time-motion study that profiles the worker?s daily activities. At the same time, noise measurements are collected with a dosimeter or sound level meter (SLM). Observations about the worker?s location and tasks or other activities are recorded along with times and durations so they can later be matched up with the noise data. After the completion of a time-motion study of the worker?s daily tasks and locations (possible noise sources), which measures the worker?s noise exposures during the recorded events, the information is entered into DOSES. The program then displays information about the worker?s accumulated noise dose over time.

Jan 1, 2009

By W. O. Philbrook

Reduced-scale models have long been used in hydrodynamics, aerodynamics, and heat transfer for studying fundamental flow relations or the performance of prototype designs under prescribed conditions. The pilot plant is a common tool of chemical engineering for investigating process variables and as an integral step in developing a new process. The metallurgical industry was rather slow to recognize the applicability of these techniques to some of its established and rather complex processes, but there has been a rapidly increasing number of applications of the principles of modeling in process metallurgy since World War II. Not only have pilot-scale operations been employed for developing methods of extracting metals that have recently achieved commercial importance, as well as new processes for some of the commoner metals, but models have also been used for engineering studies aimed at better understanding of the controlling, variables of time-honored conventional processes, It appears that the principles of similitude have become accepted as a useful tool, when properly applied, in metallurgy as in other fields of engineering. Much of the work of the Pyrometallurgical Laboratory, Region V, involves study of high-temperature smelting and refining processes for ferrous and related metals in pilot-scale equipment, such as the experimental blast furnace, converter, open-hearth, arc furnace, and rotary kiln. It was appropriate for the work of this laboratory that guiding principles for designing apparatus and interpreting results should be set down and that a bibliography of related work should be available for reference. A summary of the principles of model study and a brief review of some of the more noteworthy general papers have been published elsewhere.3/ Also, the Bureau of mines plans to publish a report of investigations describing its experimental work in this field. The bibliography is presented here as a service to others who may have use for it.

Jan 1, 1958

By Lloyd A. Morley, Robert Stefanko

1 Abaibanel, S , "Deflection of Confining Walls by Explosive Loads," Israel Jour. Technology, vol. 4, n. 1, Feb 1966. 2 Albertoni, S and others, "Numerical Computation Methods for Implosion Processes," EURATOM Proc. of the Conf. on Megagauss Magnetic Field Generation by Explosives and Related Experiments, Milan (Italy), July, 1966. 3 Alexander, S. J , and Hambly, E. C., "Design of Structures to Withstand Gaseous Explosions," Concrete, vol. 4, n 2, Feb. and March, 1970. 4 Anonymous (Belgium Institute of Extractive Industries), "Report for 1968 (covering approved equipment for Belgiums gassy coal mines)," (in French and Flemish), Amales des Mines de Belgigue, n. 6, June, 1969. 5. Anonymous (Ghent Univ., Belgium), "The Welding of Very Thick Steels. Margin of Uncertainty of the Robertson Test," EURATOM Contract 042-61-9-RDB, May 20, 1965. 6. Anonymous, "Inportance of the Nature and Size of Weld Defects with Regard to the Mechanical Strength of Pressure Vessels, (in Flemish), A. Sys. Rev. Soudure, vol. 27, n. 3, 1971. 7. Anonymous (Raentgen Technische Dienst N V., Rotterdam), "Non¬Destructive Welding," Quarterly Report No 13, EURAEC - 1342, March 30, 1965. 8. Anonymous (Staff, USBM Safety Research Center), "Research and Technologic Work on Explosives, Explosions, and Flames: Fiscal year 1969," USBM IC8492, 1970. 9. Anonymous, "Symposium on Flameproofing Intrinsic Safety and Other Safeguards in Electrical Instrument Practice, April 27, 1962," IEEE Conf. Report Ser. 3, 1963. 10. Anonymous, "Unfired Pressure Vessels," ASME Pressure Vessel Code, Sec. 8, 1965. 11. Anonymous, "Unusual Pressure Relief Devices," Industrial and Engineering Chemistry, vol 54, n. 1, Jan., 1962. 12. Archer, G. L., "Design to Avoid Brittle Fracture in Welded Structures," Paper No. 4, Improving Welded Prod Design, vol. 1, Welding Inst., Cambridge, England, 1971. 13. Bailey, F. C., "Buckling and Failure Strength of Plating Panels Loaded in Shear," Final Report NASA Contract NObs-72290, Lessels and Assoc., Inc., Waltham, Mass., Sept. 20, 1963.

Jan 1, 1974

By J. F. Barkley

"In trying various coals at one of the Government power plants, comparison was made of the ash softening temperature of each coal, with the clinkering tendencies of the coal when burned in the furnace. The proximate analyses, ash softening temperature and plant reports as to clinkering were tabulated. It was desired to bring out any correlation that might appear between the ash softening temperature found in the laboratory, and the clinkering of the ash as found in the boiler furnace.Each coal used was sampled and analyzed, and the standard ash fusion test made. The clinkerring of the coal in the furnace was observed by the furnace operator. The furnace equipment consisted of the ""V"" or Murphy type of stoker with the ordinary fire-brick arch roof. With such arrangement very high furnace temperatures are apt to be produced at the ratings carried at this plant.The softening temperature of ash is defined as the temperature at which small cone of the ash, as tested in the laboratory furnace, has fused down to a spherical lump, The softening interval is the difference between the softening temperature and the temperature at which the first rounding, or bending, of the apex of the cone takes piece. The flowing interval is the difference between the softening temperature and the temperature at which the ash has reached a fluid condition as shown by spreading out over the base in a flat layer.While the analyses of the different samples of the some coal did not vary appreciably, the ash softening temperatures were not always so consistent. It will be noted from the following examples that the ash softening temperatures of different samples of the same coal differ as much as 290° F, Hence, in order to judge this property of a coal, many samples ore desirable, taken from many different shipment."

Aug 1, 1924

By Lloyd A. Morley, Alan M. Christman

1. Anonymous. "Getting Down to Earth," booklet 25T, James G. Biddle Co, Plymouth Meeting, Pa. (1970) pp. 1-48. 2. Anonymous. "Megger Ground Tester, Special Instructions," booklet 25-J-1, James G. Biddle Co, Plymouth Meeting, Pa. (1961) pp. 1-16. 3. AIEE Committee. "Application Guide on Methods of Substation Ground¬ing," AIEE Transactions on Power Apparatus and Systems (April 1954) pp. 271-277. 4. AIEE Committee. "Voltage Gradients Through the Ground Under Fault Conditions," AIEE Transactions on Power Apparatus and Systems (October 1958) pp. 669-692. 5. American Standards Association. "American Standard Safety Rules for Installing and Using Electrical Equipment in and about Coal Mines," U. S. Bureau of Mines Information Circular 8227 (1964). 6. Armstrong, H. R. "Grounding Electrode Characteristics from Model Tests," AIEE Transactions on Power Apparatus and Systems (December 1953) pp. 1301-1306. 7. Beck, Edward. Lightning Protection for Electric Systems, McGraw¬Hill, New York (1954) pp. 281-295. 8. Bellaschi, P. L. "Impulse and 60 Cycle Characteristics of Driven Grounds," AIEE Transactions (March 1941) pp. 123-128. 9. Bellaschi, P. L. "Lightning Strokes in Field and Laboratory," Elec¬trical Engineering, Vol. 58 (November 1939) pp. 466-468. 10. Bellaschi, P. L., Armington, R. E., and Snowden, A. E. "Impulse and 60 Cycle Characteristics of Driven Grounds-II," AIEE Tran¬sactions (1942) pp. 349-363. 11. Bewley, L. V. "Theory and Tests of the Counterpoise," AIEE Transac¬tions (August 1934) pp. 1163-1172. 12. Brereton, D. S. and Hickok, H. N. "System Neutral Grounding for Chemical Plant Power Systems," AIEE Transactions on Applica¬tions and Industry (November 1955) p. 315. 13. Bruce, C. E. R. and Golde, R. H. "The Lightning Discharge," Journal of the Institute of Electrical Engineers, London, Vol. 88 (December 1941) pp. 487-505.

Jan 1, 1976

By M. B. Cooke

An analytical method for the determination of the gum-forming material in gasoline has been developed by the Bureau of Mines, during a study nor in progress to determine the best rays for elimination of such constituents from gasoline. This method is similar in principle to that previously described by Smith end Cooke,2 which involved evaporation of e sample of gasoline in a small glass dish. The evaporation was started on an actively boiling steam bath and completed in an air oven at 105°C. In the improved method described below, the stem bath has been replaced by a steam heated oven in which an inert atmosphere is maintained. Air is excluded from the oven, consequently the precision of the determination is increased. Furthermore, evaporating dishes different from those previously described may be used.

Jan 1, 1925

Provide reasonably priced, reliable fire protection for large walking draglines. Approach Fire hazards on large draglines were analyzed, then appropriate automatic fire sensing and suppression systems developed and in-mine tested. How It Works Five fire hazard areas identified for special attention are: electrical control room, high voltage transformer enclosures, circuit breaker rooms, collector ring/roller path area, and the automatic lubrication rooms. Automatic fire sensing and suppression systems were separately designed for each area. The design of each system was tailored to the hazards and equipment protected. Spot thermal sensing and Halon 1301 suppression were specified for the electrical

Jan 1, 1981

By Otto Robert Stein

Erodibility of reclaimed surface mine soils is a subject in need of quantification. Effects of soil erosion from reclaimed areas may damage surrounding areas and the quality of water in nearby streams and lakes. It may also reduce the potential productivity of the reclaimed site. A study was conducted to determine erodibilities of different reclamation treatments and a nearby unmined soil at three Indiana strip mine sites. A rainfall simulator was used to artifically erode plots con¬structed within seven treatment categories and the unmined soil. Soil erodibility was assessed in terms of the Universal Soil Loss Equation (USLE) K factor. Values for K calculated from field data were compared to values predicted from independently measured soil properties. Differences in soil erodibility between treatments were site specific. Unmined soil had the highest calculated erodibility at one site but at two other sites soils having reclaimed A horizons were highest. Shaley overburden treatments had the lowest calculated erodi¬bility. Predicted soil erodibility was usually lower than that calcu¬lated from field data. Site specific slope gradient factors (S) were developed for reclaimed A horizon treabnents. This was done because the USLE S factor overestimated the measured soil loss at steeper slopes.

Jan 1, 1983

By H. W. Kilau

The U.S. Bureau of Mines examined the wettability of bituminous and subbituminous coals before and after exposure to ambient air atmosphere, as part of an ongoing project investigating the coal-wetting abilities of surfactant solutions intended for the suppression of dust during coal mining operations. Exposure periods were generally 7 days or less, and the changes in wetting response were measured with a capillary penetration apparatus. Wetting solutions tested included a nonionic surfactant, two anionic surfactants, and pure distilled water. After exposure, higher ranked bituminous coals treated with nonionic surfactant solution and pure water showed increased wettability, but lower ranked subbituminous coals showed decreased wettability. With the anionic surfactants, the coals demonstrated opposite responses. The wettability changes appeared to be related to the coal moisture content. These changes may be amplified by specific, but incompletely understood, interactions between surfactant polar groups, absorbed water, and the coal surface.

Jan 1, 1989

By Kenneth L. Cashddollar, Terry G. Montgomery, Eric S. Weiss, John E. Going

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRI, Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test -was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere.