Search Documents

By William K. Antle

The successful application of ther mo compression lead bonding to semicondtctor or thin-film electronic devices depends on the establishment of the associated parameters. The quality of a thermocompression bond is primarily related to the process temperature and bonding force. A technique using the coelyicient of friction is presented that both reduces the time necessary for determining optimum parameter values and increases the accuracy of the results. Modern theories of the friction process are used to develop mathernatical expressions for shear and tensile bond strengths in terms of friction measurements. A further application of the pararneter-deterlnination technique concerns the measurement of surface contamination that may affect thermocompression bonding. In spite of the extensive use of thermocompression bonding, adequate methods for determining the bonding parameters have not been utilized. The quality of the weld depends on the temperature, force, and time used. There is a definite value or range of values for each parameter which assures an optimum weld. The process now generally used to obtain these values is to make several weld samples at each parametric setting, determine the mean pull strength, and relate the maximum consistent strength to optimum weld conditions. This could involve a very large number of test samples if a thorough search of each parameter were made. Experience and prior knowledge can reduce this number somewhat by limiting the investigation to a range known to contain the correct value, but the time and effort involved are still objectionable. The problems associated with thermocompression bonding of interconnecting leads to semiconductor or thin-film devices can be alleviated by the application of a new technique for establishing the process parameters. Obtaining the correct temperature, force, and duration to assure an optimum bond is accomplished by a simple measurement of the coefficient of friction. This approach increases the accuracy of parameter determination and greatly reduces the time necessary to complete the process. The approach made can be better understood by analyzing the principles of adhesion and friction on which thermocompression bonding depends. When two flat polished surfaces are placed together, the area of actual contact is much less than the apparent area determined by the over-all dimensions of the surface. This is because the microscopic surface is covered with projections which prevent uniform contact. Careful measurements of the electrical resistance across the contacting surfaces indicate the actual area may only be 1100,000 of the apparent area.' Because the actual contact area is small, extremely high pressure results from moderate force. This will produce deformation and plastic flow at contact points of the microscopic projections. The process will terminate in the creation of a large number of minute welds formed at extreme pressure and cold-worked to strong, hard bonds. Load removal will generally result in fracture of most of these microbonds because of the residual elastic stresses, unless the materials are soft. Friction between metals is due to the formation and

Jan 1, 1967

By L. L. Newman

As soon as the Congress recognized the alarming rate at which our domestic oil resources were being depleted during the war, it took action to step up the rate of research and development which the Bureau of Mines had been conducting for several years on the production of synthetic liquid fuels from coals. Under Public Law 290, approved April 5, 1944, funds were authorized for the Bureau to proceed with research, development, design and construction of demonstration plants for the hydrogenation of coal, the synthesis of oil from carbon monoxide and hydrogen, and the distillation of oil from shale. During the latter part of 1944, when it became evident that the collapse of Germany was near, a Technical Oil Mission was organized to study the German techniques of synthetic oil production. Since the cost of hydrogen or synthesis gas is one of the major factors of expense in the operation of hydrogenation or synthesis gas processes, the Bureau of Mines considered it of prime importance to include on the mission gas engineers whose instructions were to examine closely the methods employed by the Germans in solving the problem of providing low-cost hydrogen or synthesis gas for their very extensive operations on synthetic liquid fuels. The Solid Fuels Mission and the Utilities Mission, as well as the Army and Navy Missions, also included teams for the study of German gas production. Although their objectives naturally differed from those of the Technical Oil Mission and from each other, it was recognized that there was considerable overlapping of their fields of investigation. Duplication of effort, however, was largely avoided through the close cooperation between the group leaders of these missions. For example, although I went to Europe as a member of the Technical Oil Mission, my first Gcrman assignment was actually made by Dr. Harry F. Yancey, leader of the Solid Fuels Mission— to investigate the brown-coal gasification methods in central Germany. The art of gasification in the United States and England, and to a large extent in the proximity of the coking-coal regions of Germany and the rest of continental Europe, depends essentially on two stages of operation; namely, carbonization and intermittent water-gas generation. As far as the United States is concerned, complete gasification in a single stage of operation is rarely practiced, except in gas-producer operations where the product is a relatively lean gas consumed close to the point of manufacture, and for water-gas production with anthracite as a generator fuel. Complete gasification of bituminous coal has been the subject of numerous investigations. Many relatively simple modifications of the water-gas generator have been tried to permit the direct gasification of low-cost bituminous coal instead of high-cost coke and anthracite for the production of water gas. Although varying degrees of Success have been achieved and the water gas produced generally has been higher in

Jan 1, 1947

By R. H. Jacoby, M. J. Rzasa

Experimental equilibrium vaporization ratios were obtained for nitrogen, methane, carbon dioxide, ethane, and hydrogen sulfide in natural gas-condensate systems. Two different overall mixture compositions were investigated over the pressure range 500 to 4,000 psia at 100°, 150°, and 200 °F. Partial phase diagrams of the mixtures were obtained; one of these showed a critical point at 204°F and 3,875 psia. These and earlier data' were compared with the Kellogg correlation' at! 100°F and 1,000 psia. INTRODUCTION The authors' have presented equilibrium vaporization ratios for nitrogen, methane, carbon dioxide, ethane, and hydrogen sulfide in complex mixtures, such as natural gas-crude oil and natural gas-absorber oil. Since mixtures of the natural gas-condensate type also occur widely in petroleum reservoirs and often contain the non-hydrocarbons mentioned, it would be useful to have appropriate K data for calculating equilibrium vaporization conditions. Roland, Smith, and Kave-ler' obtained K's for methane and the light hydrocarbons in gas-condensate mixtures; and Poettmann and Katz3 obtained K's for carbon dioxide in a gas-condensate system. The data presented in this paper extend this coverage to include K's for nitrogen and hydrogen sulfide and phase diagrams for the experimental mixtures. EXPERIMENTAL WORK The equipment and experimental procedure was essentially as described previously, except for analysis of the vapor samples. The vapor sample bombs were filled at the pressure and temperature of the run. Immediately after sampling, a portion of this sample was flushed from the bomb into a 650 cc glass bulb, filling it to near atmospheric pressure. The sample in the glass bulb was then analyzed by the mass spectrometer. Some checks were made on this analytical procedure to find the accuracy of measurement of the C + content of the vapor samples. The modifications tried were complete fractionation of the vapor sample and the use of several liquids (depropanized condensate and retrograde liquid from several vapor samples) as calibrating materials for the mass spectrometer. The results obtained from these various checks differed by about 10 per cent relative and this is believed to be the order of accuracy of the vapor C+ concentrations.

Jan 1, 1953

By J. B. Newsom

In the Indiana limestone district, some 50 or 60 per cent of the merchantable stone in a quarry opening is waste, and only about 40 or 50 per cent of the stone from the opening is finally sold. So long as the present system of 'quarrying is used, the wastes measured and reported in this paper will continue. Comprehensive development of an entirely different method of quarrying, using wire saws for cutting, promises great improvement. Some of the savings to be expected are pointed out in the following pages. No attempt has been made to measure losses due to variations and natural flaws in the stone, since these vary greatly in different quarries, and accurate measurement would be difficult. The wastes that have been measured account for about 30 per cent of the total ledge, which leaves 20 or 30 per cent chargeable to unmeasured sources of loss. General Causes of Waste There are four general reasons for quarry waste: (1) the structure of the deposit, such as its shape, bedding planes, solution cavities and strain fractures; (2) efforts to quarry blocks which do not contain distinct color or textural variations; (3) the trade custom which permits purchasers to specify the size of the quarry blocks which they will buy, which is a matter of competition for business on the part of stone producers; (4) quarry methods, which cause the greatest amount of waste. Wide channeler cuts, hook holes, crooked splitting and uneven breaking on quarry floors are included in this category. Waste Due to Structure of Deposits The peculiarities of structure cannot be eliminated, but a chance for saving lies in quarrying to take advantage of them. The commercial deposits of Indiana limestone are lenticular masses from 20 to 70 ft. thick, and nearly horizontal. All of these deposits of good stone are in the Salem limestone, a bed in the sub-Carboniferous. The Salem is traversed by two systems of vertical fractures, a major system running from northeast to southwest and a minor system running from northwest to southeast. Where the stone is covered by an over-

Jan 1, 1932

By William Rawles

THIS report is the first of a series planned by The Mineral Inquiry, organized by the American Institute of Mining and Metallurgical Engineers to make factual studies of the world's mineral resources in their political and international relations. The efforts of The Inquiry are directed toward filling certain notable gaps in available information, without duplication of many other investigations touching this field which are being conducted by other organizations, public and private. Much of its work is indirect-suggesting topics for study by other individuals and organizations and aiding in their planning and correlation. The present report is designed to show the nationality of the commercial control of mineral resources, in addition to the geographic distribution of production by nation-in other words, the overlapping of political and commercial control. Detailed accuracy cannot be claimed for the figures presented. For some companies division of ownership by nationality has been very difficult to ascertain, as many companies are reluctant to dis-close the extent of their holdings in other corporations, and the impossi-bility of tracing all stock ownership is obvious. Also there are frequent changes in the distribution of. stock control. The percentages given rep-resent only the participation that has been identified definitely, even though it is known in some cases with fair certainty that larger interests exist, as, for instance, American participation in foreign chromite companies. In bringing together these figures we have had the cordial co-operation of the United States Bureau of Mines, the United States Geologi-cal Survey, the Mineral Division of the Bureau of Foreign and Domestic Commerce, the Brookings Institution, and of many specialists connected with the mineral industries covered. The report does not cover the entire list of minerals. Coal, although it is one of the most important minerals, was omitted because , not more than one or two per cent of the world's production comes from mines that are owned by companies foreign to the countries where the coal is produced. Others, such as gold, are omitted because sufficient data have not yet been accumulated. It is hoped that some of these may be covered in subsequent reports. It is not our purpose here to discuss the significance of the figures sub-mitted, but only to point out the general nature of the problems on which they have a bearing.

Jan 1, 1933

By J. W. Whalen

The design, operation and evaluation of an instrumental method for the determination of fluid saturation in porous materials during multiphase flow studies is described. The presence of a magnetic tracer comprising approximately 20 per cent by weight of the aqueous phase is necessary in the utilization of this method. The results of two-phase relative permeability studies on two samples of porous media are presented. The realizable accuracy of the magnetic susceptibility apparatus in fluid saturation determination is estimated to be 2 saturation per cent. The response characteristics of the instrument, together with its simplicity of operation and maintenance are sufficient to recommend its use in routine laboratory studies. INTRODUCTION The problem of fluid saturation determination in laboratory multiphase flow studies characterizing oil recovery processes is one which has been given exhaustive study. Briefly the requirements which are considered essential for a method sewing this purpose are: (1) that the measurement be made external to the porous rock sample under study with no interruption of the fluid flow pattern, (2) the saturation indication must be independent of fluid distribution in the volume scanned by the measuring device, (3) the sensing element should have a small field of definition enabling several independent measurements to be made along the length of a core sample, and (4) the properties of the fluid phases should not be too greatly influenced by required tracer substances. Several methods of saturation determination have found acceptance as meeting most of the above requirements. These include resistivity,1 X-Ray absorption,2,3,4 radiotracers,5,6,7 and neutron8 diffraction The merits of these techniques have been discussed elsewhere in detail and will not be considered here. It may, however. be pointed out that the elaborate instrumentation required by the methods mentioned above, with the exception of the resistivity method (which is undesirable from other standpoints) encourages the development of methods of saturation determination which, while meeting the requirements listed, are simple to operate and maintain. It is the purpose of this paper to describe the instrumentation and evaluation of a technique for the determination of fluid saturation which combines relative simplicity with an accuracy and applicability comparable with methods now in practice. DESCRIPTION OF THE METHOD If the magnetic susceptibility of one of the fluid phases contained within a porous material is sufficiently greater than that of the remaining phases, the fluid content of the material with respect to that phase may be determined by an induction measurement. This may be accomplished by measuring the induced voltage in the secondary of a transformer which contains the porous sample and its interstitial fluids as a portion of the magnetic flux path. Since the fluids used in multiphase flow studies involving petroleum reservoir samples possess uniformly low magnetic susceptibilities, the use of a magnetic tracer in one of the fluid phases is required. In view of the relatively high paramagnetic susceptibility of salts of the transition elements, together with their high water solubility. these compounds become logical choices as tracer materials. Cobaltous chloride, having a specific magnetic susceptibility of 17.5 x 106 cgs electromagnetic units, was used as the tracer material throughout this work, in a concentration of approximately 20 per cent by weight in the aqueous phase. MAGNETIC SUSCEPTIBILITY APPARATUS Basically, the magnetic susceptibility apparatus consists of a transformer serving as the detecting head, a

Jan 1, 1955

By D. R. Spink

In the preparation of zirconium and hafnium metals, there are many indications that impurity levels control the physical and chemical properties of the metal. The purpose of this work was to develop methods of producing pure raw materials that could be reduced to highly pure metals. Early work by the Carbomcndum Metals Co. and others indicated that certain fused salts were highly efficient in the removal of impurities from gaseous zirconium tetrachloride. We have developed workable fused salts along with a continuous and higly efficient scrubber design which can be used to produce very pure zirconium tetrachloride. Metal made from the purified tetrachloride has been shown to approach crystal bar metal in purity. Scrubber designs are discussed with recommended materials of construction. VARIOUS methods have been used to purify zirconium (and hafnium) tetrachloride. Most of these methods involve thermal degassing initially (the removal of more volatile compounds at temperatures below that where zirconium tetrachloride exhibits a significant vapor pressure) followed by a sublimation step (which conveniently leaves the nonvolatiles behind.) While these procedures effect definite purification, such processing is batchwise and does not result in optimum purification. Early work by The Carborundum Metals Co. and others indicated that fused salts were highly efficient in the removal of impurities from gaseous zirconium tetrachloride. The objective of this work was to develop a continuous fused-salt scrubbing process that would yield high-purity zirconium and hafnium tetrachlorides. The term "fused salt" refers to the molten state of ionic compounds and as used here, specifically refers to alkali metal and alkaline earth halides. Fused salts, because of their many valuable properties, are becoming increasingly im- portant industrially. These valuable properties of the fused salts are: 1) stability at elevated temperatures; 2)low vapor pressure; 3) low viscosity; 4) ability to dissolve many different materials; and 5) good elctctrical conductivity. All but the last property enhances the use of fused salts as scrubbing agents for zirconium and hafnium tetrachlorides. Fused-salt scrubbing may be defined for our purpose as the intimate contact between a gaseous compound and a molten salt with the purpose of removing impurities from the gaseous compound. In this case, the gaseous compound is zirconium tetrachloride which submlimes at 331°C. When this gas is contacted with a molten salt, impurities such as aluminum, iron, and titanium are removed and the resulting product is considered fused-salt scrubbed. Zirconium and hafnium are sold to a purity specification. Generally speaking, normal production without scrubbing is capable of meeting specifications. There are, however, several considerations That make the knowledge of methods of additional purification highly desirable. These are: 1) the control of product analysis; 2) the production of a pure product for special applications; 3) the salvaging of off-specification material; and 4) the use of raw materials with higher impurity levels than 1 he present raw materials. You will note that items 1 and 2 are somewhat complementary to each other and that item 4 assumes that The present process has impurity removal limitations. To better understand the part that fused-salt scrubbing of zirconium tetrachloride plays in the manufacture of zirconium, Fig. 1 contains an illustrated flow sheet of the industrial production of zirconium metal. In referring to Fig. 1, we can point out the specific benefits derived from our ability to purify zirconium tetrachloride. Purification of the crude (hafnium-containing) zirconium

Jan 1, 1962

By S. G. Cupschalk, F. A. Dahlman, J. J. Wert

Studies have been undertaken to determine the indicidual effects of particle size, degree of long-range ovder, antiphase domain size, and root mean square stran on the microhardness and yield strength of ordered alloys. Dnta have been analyzed for Cu3Pt initzally ordered to a value of 0.82 and after deformations of 1 and 6 pct. It was observed that deformation fleatly reduced the degree of long-range order. Furtherrnore, wztkin this range of relatively small deforntntlons, the average particle size changed very little while the antiphase domain size was greatly reduced. Smultaneosly, the mcrohardness changed by a factor of two durzng the deforrtation process. PREVIOUS studies have reported some of the effects of cold work on the broadening of X-ray diffraction peaks. These investigations were performed on powder and wire samples representing both ordered and disordered states; i.e., the specimens were initially studied in a severly cold-worked condition. By comparing the difference in line shape between the annealed and cold-worked peaks, fundamental information was obtained concerning particle size, strain distribution in different crystallographic directions, degree of long-range order, and change in antiphase domain size. Considerable theoretical work has been done concerning the analysis of diffraction data obtained from cold-worked metals. Stokes' expressed the change in diffraction profiles in terms of Fourier coefficients. Much of the work in this area has been summarized by warren2 in an extensive review article concerning the analysis of plastic deformation by X-ray diffraction. Cohen and Bever3 applied these techniques in studying the effects of cold work on alloy systems exhibiting long-range order. They utilized the Fourier coefficients of fundamental peaks in conjunction with those of the superlattice peaks to determine the change in antiphase domain size. Little work of this nature has been reported for ordered systems that have undergone small degrees of plastic deformation. The purpose of this investiga-tion was to determine the effects of small deformations in such a material with respect to particle size, strain distribution in various crystallographic directions, antiphase domain size, degree of long-range order, and hardness. EXPERIMENTAL PROCEDURE CusPt was used for the initial investigation since the order-disorder transformation takes place with- out a change in crystal structure. The transformation is readily detectable via X-ray diffraction techniques due to the large difference in the scattering factors of copper and platinum. Additionally, the alloy is relatively low melting (approximately 1300°C) and is easily deformable in both the ordered and disordered states. 1) Specimen Preparation and Cold Working. A 100-g, 12-in. diam., cylindrical specimen of Cu3Pt was prepared by melting and casting 99.99 pct pure Cu and Pt i.n vacuo. Prior to any mechanical working, the material was homogenized in a vacuum for 60 hr at 100O0C, and surface defects were removed by machining to a depth of approximately 116 of an in. The material was then cold-rolled, with an intermediate anneal, into a strip approximately 12 in. wide by 14 in. thick. Straightening and flattening removed another 0.025 in. from the thickness. After a recrystallization treatment at 750°C for 30 min, the specimen was slow-cooled from 55OoC, at the rate of 6°C per hr, down to 150°C to induce superlattice formation. This treatment yielded an ASTM grain size of 7 and a degree of long-range order equal to 0.83 0.06. After obtaining X-ray and Knoop hardness data, the sample was cold-rolled approximately 0.75 pct in one pass through a hand-operated jewelers' mill. X-ray and hardness data were again obtained and the specimen was reduced an additional 5.41 pct in a single pass through the mill. 2) X-Ray Measurements. The specimen was examined in the ordered condition and after the two degrees of cold working previously mentioned using a General Electric XRD-5 unit equipped with a spectrometer and scintillation counter. Using Mo-Ka radiation with a zirconium filter, six orders of the 100 reflection were obtained. It was anticipated that point counting would be necessary for an accurate determination of the low-intensity peaks and tails: however, it was demonstrated that, by using a scanning speed of 0.2 deg per min and the appropriate time constant, the recorded data were sufficiently accurate. Thus, for ease of experimental procedure, all peaks were recorded on chart paper. Specimen position in the holder was considered to be insignificant after making a series of measurements of the same peak area in different positions with respect to the beam. Since peak overlapping did occur at high values of 20, it was necessary to separate the peaks graphically prior to analyzing the data in order to minimize this source of error. The peak tails were also carefully drawn to obtain the best possible data. Fourier coefficients of the line profiles were calculated on an IBM 7072 computer, and graphical meth-ods2j3 were employed in analyzing the results. For this type of calculation, in which the line profile is represented by intensities taken at set intervals, the intervals selected must be sufficiently small to give an accurate representation of the line profile. It was decided that for 20 = 0.02 deg the line profiles were

Jan 1, 1967

By Dale A. Vaughan, Oliver M. Stewart, Charles M. Schwartz

Solid-solubility limits at 1500°, l000q and 500°C for carbon, nitrogen, and oxygen in high-purity tantalum were determined by X-ray lattice-parameter methods. For carbon, the solubility was found to be 0.17 at. pct at 1500°C, and less than 0.07 at. pct at 1000°C. A nitrogen solubility of 3.70 at. pct at 1500° C decreases linearly with temperature to 2.75 at. pct at 1000°C, and 1.8 at. pct at 500°C. In the case of oxygen, the solubility was found to be 3.65 at. pct at 1500°C, 2.95 at. pct at 1000°C, and 2.5 at. pct at 500°C. The phases Ta2C, the low-temperature modification of Ta205, and Ta,N of unknown composition but which has a superlattice structure based upon the original bcc tantalum lattice have been identified as the initial precipitates in the respective systems. Metallographic methods were employed to verify the X-ray analyses. The etching behavior of Ta is discussed in terms of lattice i?rzperfections and precipitate phases. The excellent fabricability, high melting point, and nuclear properties of tantalum are responsible for interest in this refractory metal. Data on the solid solubility of the interstitial elements (oxygen, nitrogen, and carbon) in tantalum and on the precipitate phases are somewhat limited. The significant contributions are discussed below. Because the purity of electron-beam melted tantalum (only recently available) is considerably higher than that used in previous studies, the present investigation was initiated. Gebhardt et all-3 have investigated the tantalum-oxygen and tantalum-nitrogen systems with particular reference to the changes in physical properties and to the rates of reaction between these gases and the metal. The solubility of oxygen in tantalum was reported2 to be 3.7 at. pet at 1500°, 2.3 at. pet at 100O°C, and 1.4 at. pct at 750°C. Schonberg4 reported that several oxide phases (Ta40, Ta,O, TaO and Ta,05) exist while X-ray studies by Gebhardtl showed only two oxides, Ta,05 and an unidentified phase which was associated with a platelet-type precipitate. La-gergren and Magneli,' however, questioned the existence of compounds other than the two allotropic modifications of Ta,05 for the tantalum-oxygen system. In the case of nitrogen, the solubility was estab- lished by Gebhardt3 to be of the order of 7 at. pct at 1800°c. The solubility was reported to decrease rapidly with temperature, and, although no limits were established, a precipitate phase was observed by Gebhardt except when the high-nitrogen specimens were cooled very rapidly from the reaction temperature of 1800c. He reported the initial precipitate phase to be a tetragonal distortion of the bcc tantalum lattice while Schonberg6 reported the phase lowest in nitrogen Jo be a cubic super-lattice with a cell size of 10.11 A. Two other nitride phases, Ta,N and TaN, were reported; these appear to be isomor-phous with the carbides of tantalum. The tantalum-carbon system was investigated by Ellinger7 and by Lesser and Braurer. Two compounds, Ta,C and TaC, were reported to exist, each with a range of composition. The solubility of carbon in tantalum was found to be practically nil at all temperatures. Thus, of the interstitial elements which are present in small amounts in high-purity tantalum, carbon might be expected to form precipitates. The present investigation was initiated to obtain additional data on the solid-solubility limits of these interstitials at 1500°, 1000°, and 500' with particular emphasis on the distribution and the identification of the precipitate phases. EXPERIMENTAL WORK AND RESULTS In the present investigations of the solid solubility and of the precipitate phases in the systems tantalum-nitrogen, -oxygen, and -carbon, high-purity tantalum was reacted with high-purity gases, homogenized at 1800°c, and annealed at and quenched from 1500°, 1000,

Jan 1, 1962

By E. G. Bailey

The bituminous coal industry faces a real problem, if it desires to retain the position in the power-generation field to which it is economically entitled. More power is probably produced today for electrical energy, for steam-driven and steam-heating industries and processes, for transportation by rail, water, highway and air, collectively, than ever before, and yet the total bituminous coal production has decreased about 38 per cent, from 575,000,000 tons in 1926 to 357,500,000 tons in 1934. It is not the intention of the writer to recommend coal as a fuel for automobiles and airplanes, but rather to point to these forms of transportation as being responsible in a very measurable degree for reducing the coal consumed by railroads. Petroleum products may still further reduce consumption of locomotive fuel through the extension of the use of Diesel-driven trains. Oil-burning steam-driven locomotivcs are replacing coal in some places, where railroads operating high-speed passenger trains are willing, temporarily at least, to pay a premium for the fuel that is low in ash and produces less smoke and practically no cinders. In the navy and ocean-going passenger ships, oil is so firmly established, and has such definite advantages over coal as formerly fired, in steaming radius, in ease of bunkering, cleanliness, and reduction in firing labor, that very outstanding developments in the handling and burning of coal will be rcquired in order to replace oil. For freighters on the Great Lakes, coal is the logical fuel, but there is great and immediate need of radical improvements in its use, else that market also may be lessened. It is not within the scope of this paper to discuss in detail bituminous coal for either locomotive or marine use, but, rather, generation of power in stationary plants, consisting of electrical generating stations and that very large group of miscellaneous industrial plants, such as paper, rubber, textile, steel and other industries that use electrical, mechanical, and steam power, derived from either hydro or some form of fuel.

Jan 1, 1936

By Joseph B. Umpleby

The oil industry is at the parting of the ways in relating fundamental engineering concepts to legal interpretations and field practices. The old concept, based on an erroneous analogy to wild game, that oil and gas are migratory substances and belong to him who reduces them to possession regardless of their point of origin in the reservoir, has come to be quite generally recognized as the basis of many of the serious ills and extravagances of the industry. The chain of consequences resulting from this erroneous conception has been traced elsewhere and need not be recounted here. The important problem at this stage in the development of the industry, when laws are being revised by legislative action and modified by court decisions; when added powers are being exercised by voluntary committees and official regulatory bodies; and when the need for control of output has forced itself to the forefront, is to see to it that new law and action are based on sound engineering concepts. Reservoir Energy Common Property Since the study of gas instituted by the Marland committee of the American Petroleum Institute in 1927, a great mass of information has accumulated concerning the function of gas in the development and production of oil. This wealth of data leads to the conclusion that every oil pool contains three resources: Oil, gas and reservoir energy. I take it that the central problem of this symposium is the ownership of these three resources and that "source" and "utilization" are involved because of their bearing on ownership through the demands of equity and conservation. In order to facilitate the discussion, permit me to state categorically, that: The oil and gas in a particular tract should belong to the owners of the mineral rights in that particular tract, but the reservoir energy should be common property of all owners of mineral rights in the pool I take it that apportionment of oil and gas among owners according to the relative amounts that exist in place in their respective tracts is

Jan 1, 1933

By E. G. Bailey

The bituminous coal industry faces a real problem, if it desires to retain the position in the power-generation field to which it is economically entitled. More power is probably produced today for electrical energy, for steam-driven and steam-heating industries and processes, for transportation by rail, water, highway and air, collectively, than ever before, and yet the total bituminous coal production has decreased about 38 per cent, from 575,000,000 tons in 1926 to 357,500,000 tons in 1934. It is not the intention of the writer to recommend coal as a fuel for automobiles and airplanes, but rather to point to these forms of transportation as being responsible in a very measurable degree for reducing the coal consumed by railroads. Petroleum products may still further reduce consumption of locomotive fuel through the extension of the use of Diesel-driven trains. Oil-burning steam-driven locomotivcs are replacing coal in some places, where railroads operating high-speed passenger trains are willing, temporarily at least, to pay a premium for the fuel that is low in ash and produces less smoke and practically no cinders. In the navy and ocean-going passenger ships, oil is so firmly established, and has such definite advantages over coal as formerly fired, in steaming radius, in ease of bunkering, cleanliness, and reduction in firing labor, that very outstanding developments in the handling and burning of coal will be rcquired in order to replace oil. For freighters on the Great Lakes, coal is the logical fuel, but there is great and immediate need of radical improvements in its use, else that market also may be lessened. It is not within the scope of this paper to discuss in detail bituminous coal for either locomotive or marine use, but, rather, generation of power in stationary plants, consisting of electrical generating stations and that very large group of miscellaneous industrial plants, such as paper, rubber, textile, steel and other industries that use electrical, mechanical, and steam power, derived from either hydro or some form of fuel.

Jan 1, 1936

By Paul Munoz

TRINIDAD, which has never been. seriously consid-ered as a large oil producer, has recently taken a new lease on its oil life through active development work being carried on by a newly organized American company that has been conspicuously successful in the short time in which it has operated on the island. From an oil operator's point of view Trinidad pos-sesses numerous natural advantages which are not found in any other oil producing country. The climate, while tropical, is healthy. The nights are always cool. Deep-water shipping ports in protected waters are available within short pipe-line distance from the pro-ducing fields. The distance from Trinidad to the At-lantic seaboard of the United States is less than from the Gulf Coast or from Mexico. The labor supply is abundant and can be had at reasonable rates. The island enjoys a good, stable government under British rule and is traversed by a net-work of excellent govern-ment roads. From a production standpoint the fields being de-veloped by Trinidad Oil Fields, Inc., the company re-ferred to above, present interesting problems which are being successfully solved. The oil sands are extremely fine; some of them having over 50 per cent passing 100- mesh screen and, with the exception of the Palo Seco field, the sands are loose, with shale-breaks and shale capping and with rock pressures running up to 600 lb. per square inch. Rotary drilling is universal, as the formations encountered are soft Tertiary shales, clays, sandy shales and sands, with occasional sandstone and lime shells, which are easily drilled with the rotary. As high as 600 ft. of hole in 24 hr. has been made in some of this company's wells. Production is at present obtained at depths ranging from 500 to 2500 ft. but further development will probably result in deeper pro-duction being obtained. The oil being produced ranges from 21 deg. to 37 deg. Bé gravity and is all asphaltic base oil.

Jan 7, 1927

By E. L. Bruce

GOLD occurs in many mineral deposits in the rocks of the Canadian Shield. It is present in the ores of many base metals and a considerable quantity is recovered as a by-product from the production of copper at Noranda, of nickel and copper at Sudbury and of copper and zinc at. Flinflon. But the greater part of the gold production of Canada is from deposits in which gold is the only metal of value. No gold is obtained from placer deposits within the borders of the Canadian Shield. A brief review of the geological relations of some of the gold deposits of the Canadian Shield will be presented in an attempt to explain certain associations. Only those which are being worked for their gold content will be considered and descriptions will be conned to representative types of deposits, chiefly those of major importance; a few others, differ-ing in certain features from those of the older and larger mines, will be included in order to illustrate the general conditions in which gold occurs in these ancient rocks. Brief summaries will be given of the geological relations of the Beattie and Siscoe mines of northern Quebec, of the mines of the Porcupine and Kirkland Lake areas of northeastern Ontario and of the Howey, Central Patricia and Little Long Lac mines of northwest-ern Ontario. Genetic relations to igneous rocks of granitic composition, outcropping in the vicinity, have been assumed for many of these deposits. Undoubt-edly the ore minerals have been derived from igneous sources and, for some occurrences, there is evidence suggestive of genetic relationship between the ore bodies and neighbouring intrusive rocks. During the past few years, however,, many investigators have expressed doubt of the genetic relationship of certain ore bodies to igneous masses near which they occur. As will be seen from references in the following descriptions the importance of the structural conditions in localizing deposition has been realized. This is pointed out for Canadian pre-Cambriang old deposits by E. T. Dougherty, who also refers to the

Jan 1, 1937

By J. C. Wright

A practical program of education for workers of the mining industries is being formulated by the Federal Board for Vocational Education in cooperation with the states in which this industry is a dominant one. The Federal Government last year passed a law, known as the Federal Vocational Education Act, that provides for the promotion of vocational education and for cooperation with the states in the promotion of such education in agriculture and trades and industries and in the preparation of teachers of vocational subjects. More than 1,000,000 men in the continental United States are employed in mines and quarries. The following table, from the 1910 Census Report, shows the relative importance of mining and manufacturing pursuits: Manfactures Mines and quaRRies Employees.......... 7,405,313 1,109,410 Capital............. $18,428,269,706 53,380,525,841 Value of product..... $20,672,051,870 $1,238,410,322 Of the more than 1,000,000 men employed in mining, almost three-fourths are engaged in the production of bituminous and anthracite coal; one-fifth, in the production of copper, iron, lead, zinc, and other metals; and the remainder in getting out structural and miscellaneous materials from quarries. The meeting of the needs of the coal-mining industry, therefore, is the problem of greatest importance in the point of numbers to be served. Moreover, the dangers in coal mining are greater than in metal mining. Practically all states have set up educational and technical standards for the position of foreman, boss, superintendent, etc., and every applicant for these positions must have a certificate of competency. The qualifications, too, are becoming increasingly difficult in the field of technical information. In some states, every miner must have a certificate, which is issued by the mine examining board only after an oral examination. Did these state laws not call for definite and comprehensive plans for the vocational education of men in the mining regions, the conditions

Jan 1, 1919

CONTENTS PAGE FULTON, CHARLES H., and READ, J. BURNS-A New Roasting Furnace for Zinc Flotation Concentrate. Discussed by Charles H. Fulton, Arthur S. Dwight, B. M. O'Harra, Kurt Stock 1 STOCK, KURT.-Redistillation of Zinc. Discussed by G. E. Dalbey, Kurt Stock.. 3 BEASLEY, F. E.-High Zinc in Lead Blast-furnace Slags. Discussed by R. C. Canby, R. L. Lloyd, C. R. Haywood, G. E. Dalbey, A. S. Dwight, E. P. Mathewson, A. L. Walker, B. M. O'Harra, and C. P. Linville 4 STEELE, E. W.-Application of Pulverized Coal to Copper Refinery Furnaces. Discussed by F. R. Pyne, E. P. Mathewson 11 LINVILLE, C. P.-Recovery of Arsenic and Other Valuable Constituents from Speiss. Discussed by C. R. Hayward, C. P. Linville, G. E. Dalbey, A. S. Dwight, Edward F. Kern, Karl Eilers, E. P. Mathewson 12 A New Roasting Furnace for Zinc Flotation Concentrate Discussion of the paper of CHARLES H. FULTON and J. BURNS READ, presented at the New York Meeting, February, 1925, and issued, as Paper No. 1362-D, with MINING AND METALLURGY,. October, 1924. G. E. DALBEY, East Berlin, Conn. What would be the, effect on the formation of sulfates of an increased water vapor content in the roasting gases? CHARLES H. FULTON.-I cannot answer that from our experience. The question of the formation of sulfate in the roasting of zinc is mainly one of temperature and the concentration of S02 and S03 in the gases. We found we could roast almost completely to sulfate if the concentration was kept at the proper point. We, however, did not care to do this because we wished to make a 5 to 6 per cent. S02 gas for sulfuric-acid work. The sulfating of the zinc oxide in the proper concentration of gases goes on very rapidly. There are certain places in the furnace system such as the Cottrell and in a part of the dust chamber in which the roasted

Jan 6, 1925

By John E. Conley

THE production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.1 The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require additional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnston,2 Smyth and Adams,3 Ralston et al.,4 Furnas,5 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894º to 898º C. The dissociation of dolomite and magnesite, although studied by several investigator,4, 6, 8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (1) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1939

By H. H. Kellogg

Equations representing the standard free energy of formation as a function of temperature, for thirty metallic chlorides, are presented and plotted on a free-energy vs. temperature diagram. The use of these data for calculations on reduction of metallic chlorides, refining of metals with chlorine, and chlorination of metallic oxides and sulphides is illustrated. CHLORINE metallurgy' has attracted metallur- gists for more than a century because the unusual properties of the metallic chlorides—low melting point, high volatility, and ease of formation from the oxides—make possible many useful extractive processes. Interest in chlorine processes is undergoing a renaissance due to present availability of chlorine at relatively low prices, and to recent advances in technology. During the present century there have accumulated a considerable number of reliable values of the thermodynamic constants for the metals and their chlorides. These data permit the calculation of free-energy equations for many metallurgically important reactions. Consideration of free-energy values makes possible certain predictions of the direction and extent of a given reaction, as well as the effect of temperature, pressure, and composition upon the result. Reaction rate, although not predictable from free-energy data, is usually sufficiently great at elevated temperatures that diffusion of the reactants and products to and from the zone of reaction determines the actual rate. Thus, if the free-energy indication is favorable, the chances are good that a high temperature metallurgical reaction will proceed at a reasonable rate, if adequate provision for rapid diffusion has been made. This paper presents standard free-energy equations for a number of metallic chlorides, based on data which are scattered throughout the literature. The equations are presented in a form that simplifies their use, and typical examples are given of the application of free-energy data to metallurgical processes. Free Energy of Reaction The free-energy change (AG) of a reaction is the true measure of the "driving force" of the reaction under a given set of conditions, and this is related to the standard free-energy change (AGO) of the reaction as follows: For the reaction: bB + cC = dD + eE ?G = ?G°+RTln ADd. AEA / ABb. ACc where A, = activity of constituent (i) T = absolute temperature, OK R = gas constant The criterion of a spontaneous reaction from left to right, at constant temperature and pressure, is a negative value for the free-energy change (?G). The standard free energy of the reaction is equal to the free energy of the reaction when all the reactants and products are at unit activity, since under these conditions the second term on the right-hand side of eq 1 is equal to zero. The concept of activity is treated fully in many textbooks on chemical thermodynamics1 and in a recent article by Chipman.2 Briefly, the activity (A,) of a constituent (i) is a measure of the reactivity of this constituent relative to its reactivity in some arbitrary standard state. For liquids and solids the standard state most often used is the pure liquid or solid constituent. Thus the activity of a pure liquid or solid in a metallurgical reaction is equal to unity. Gases under moderate pressure and at elevated temperatures behave very nearly as 'idea1 gases,' and the standard state is chosen as the gas at 1 atm pressure. The activity of an ideal gas is therefore equal to its partial pressure, and this relation is sufficiently exact for real gases in most metallurgical reactions. For a liquid or solid solution there is in general no simple way to express the activity of a constituent as a function of its concentration, and activity must be determined by experiment. A few solutions follow a so-called 'ideal' behavior, and if the pure constituent is chosen as the standard state, the activity of a constituent in an ideal solution becomes equal to its mol fraction. When a reaction reaches a state of thermodynamic equilibrium at constant temperature and pressure, AG becomes equal to zero and eq 1 reduces to: [ADd . AEe ?G°=RTln Abb ¦ Ac c equilibrium [2] The brackets surrounding the activity term are used to emphasize that each of the activities is an activity under equilibrium conditions—not just any arbitrarily assigned value. The bracketed term is the equilibrium constant (K) of the reaction. Eq 2 makes possible the calculation of equilibrium activities for a given reaction, if AGO is known at the desired temperature. The standard free-energy equations presented in this paper were calculated from the fundamental thermodynamic values of enthalpy of formation at 298°K (AH°,), standard entropy at 298°K (So298), heat capacity as a function of temperature (Cp), and enthalpies of transition, fusion, vaporization, and sublimation for the various constituents. Where possible the data reported in the recent "Selected Values of Chemical Thermodynamic Properties," published by the Bureau of Standards," were used. A large number of data came from the publications

Jan 1, 1951

By Walter H. Bruckner, George B. Clark

Since the end of World War 11 interest has been increasing in the use of shaped charges in the mining industry and in other industries using explosives for blasting purposes. Shaped charges employ the principle known as the "Munroe effect," which was discovered by Charles E. Munroe more than 50 years ago (in 1888). Details of their design have been explained elsewhere.1,2,3 Fig I shows the essential features of design of two types of shaped charges (with conical and hemispherical cavities) and a schematic sketch of their action upon detonation. The following discussion deals with the behavior of the metal in the cavity liners when they are subjected to intense Pressures exerted when the explosive charge is detonated. Among the conclusions reached in research on shaped explosive charges, the following have been established conceming cavity liners:1'2 I. The optimum wall thickness of a conical cavity liner is dependent upon the apex angle of the cone as well as On the base diameter of the charge. Acute apex angles require thinner walls for optimum perfonnance and more obtuse angles require thicker walls for the same base diameter. '. Cones were more effective in forming a penetrating jet when the walls were tapered; that is, the thickness of the wall of the cone increased from the apex down. 3. The physical and mechanical properties of metals have a marked effect upon their performance as cavity-liner material. Boiling point, ductility, malleability, ten-sile strength, and hardness are among the properties that influence the effectiveness of a metal used as a cavity liner. Lead, for example, makes a wide, flat crater in steel plates. Aluminum makes a deeper crater than lead, and an aluminum alloy having a high tensile strength makes a deeper hole, but slightly smaller in diameter. Cast iron makes a deep, narrow hole. These findings, together with the following analysis under Metallographic Survey of slug, offer solutions to many of the problems involved in solving the mechanism of the formation of Munroe jets. It has been fairly well established that cavity liners collapse in a manner similar to that indicated in Fig 2, Conical liners are known to collapse upon themselves while hemispherical liners are believed to turn inside out in the process of jet formation. The first has been definitely proved by recovery of collapsed portions of cones, while liners from partly detonated charges show that hemispheres may turn inside out. Fig 3 shows a sketch of a recovered slug from a 6-in. shaped charge using a 45" cone made of cast iron. (This size of charge drilled holes up to 3 ft in depth in solid granodiorite.)

Jan 1, 1949

By C. R. Boyd

The region to which I have the pleasure of calling your attention, though limited in area, is remarkable for the quantity and purity of its mineral deposits, and in these respects it would be difficult to find its equal anywhere. IRON ORES. The red and brown hematites, pipe ore, and semi-magnetites, from which is made in charcoal furnaces the highest quality of iron for car-wheels, extend through the counties of Giles, Montgomery, Pulaski, Wythe, Smyth, Washington, Bland, Tazewell, Russell, Scott, Lee, Floyd, Carroll, and Grayson, Virginia, and run over into Ashe County, North Carolina. One locality of semi-magnetite, in the centre of the great Giles County basin, has in sight, by actual measurement, 50,000 tons of ore, which, according to Prof. Fesquet, contains 69.74 per cent. of iron and no phosphorus. In the great brown-ore belt, which passes through the counties of Montgomery, Pulaski, Wythe, Smyth, and Washington, there is an extraordinary deposit of more than a million tons. A small section of this very long vein, on Cripple Creek, in the County of Wythe, yields an ore which, analyzed by Mr. James Aumann, gave the following results: Metallic iron,........58.15 Water,.........12 96 Alumina,........2.32 Silica,.........1.09 Phosphorus,.. none. At one point towards the western end of Red Land Mountain, in Pulaski County, New River section, I measured a body of ore in this belt which will yield, to a depth of 150 feet, over 8,000,000 tons, and the deposit extends far below the 150 feet measured at the upper part. Again, at Rich Hill, near the mouth of Reed Island Creek, these veins show extraordinary surface development, giving an ore of very great purity. At numerous places, also, in the counties of Giles, Bland, Tazewell, Russell, Scott, Wise, and Lee, these brown and red iron ores are exposed in such vast quantities as to baffle both description and measurement. That of Chestnut Flat, in Giles County, back or west of the Angel's Rest Mountain, is an easily reducible ore, blood-red when crushed, of which there are fully 300,000 tons in sight. Its analysis is as follows :

Jan 1, 1880