Search Documents

By Darrell Wilder

The Trenton Water Treatment Facility in Trenton, New Jersey, is expanding to upgrade existing facilities and to meet the increasing demands of the public. The facility sits uncomfortably between the northern bank of the Delaware River and Route 29, a busy traffic corridor. Flooding along this bank of the river occurs frequently and disrupts traffic along Route 29. The expansion plans for the facility call for several large clarifying tanks on a mat foundation covering an area of about 100 x 350 ft. The original design was to remove and replace up to 20 ft of existing fill and soft materials. Due to the close proximity to the existing structures and the Delaware River, it would be necessary to use sheet piles and tiebacks to support the proposed excavation, as well as the existing structures. The solution adopted consisted of the installation of vibro-replacement stone columns to improve the in situ soils and eliminate the need for excavation and replacement. This approach was tremendously successful. It mitigated the significant risk of flooding of the excavation, and provided a cost-effective alternative to mitigate settlement of the proposed tanks on the poor soft subgrade soils. This paper presents the details of the criteria for selection and design of the stone columns, and the process followed for installation of the stone columns and for verification of the level of soil improvement achieved. It also includes a back analysis of the results of a large scale, 10- by 10-foot plate load test performed on a group of stone columns using numerical procedures and recommendations for design and construction.

Jan 1, 2008

By Ben C. Gerwick

Large diameter steel tubular piles installed vertically or on a slight rake, offer many advantages as the foundations of major overwater bridge in regions of high seismicity. By proper selection of diameter and wall thickness, an optimum balance between stiffness and strength can be achieved. Under strong seismic motion, the piles will deflect and bend so as to reduce the acceleration forces transmitted to the superstructure, while still limiting drift. A major advantage of this concept is that the mass of the footing block is significantly reduced from that of the conventional pier. The design of the footing block requires great care in order to transfer the high shears and moments. Where the soils consist of significant depths of sediments, the kinematic interaction of soils, piles and structures must be considered. Moments will be a maximum just under the footing block. Filling the top portion of the pile with concrete will prevent local buckling and assure ductile behavior even under overload. Typically the piles will be long, with most or all of their support furnished by friction and will require the use of very large pile hammers to achieve the required capacities. Where the piles are founded on rock or in hardpan, sockets will be drilled and filled with reinforced concrete. For these piles, high moments can occur both at the head and just below the rock surface, so the concrete infill should extend the full length. This paper describes the use of tubular piles driven through the deep silty sands of the Jamuna River, Bangladesh, and also where socketed into the near-surface rock for the mail pylon pier of the new San Francisco-Oakland East Bay Bridge in California.

Jan 1, 2013

By Barry C. Roth

Driving of large piles in water can impact marine wildlife. Bubble curtains can mitigate these adverse effects. The procedures for and preliminary results of monitoring airborne, waterborne and groundborne vibrations with and without bubble curtains on a test project involving 2.438 m piles to 110 m is reported here. We observed fish kills and sea lions apparently fleeing the area. These phenomena were presumably due to the extreme acoustic effects of the powerful hammers which generated waterborne sound intensities locally in excess of 240 dB. This waterborne pile driving noise data collection undertaking is believed to be the most extensive ever attempted.

Jan 1, 2001

By Franz-Werner Gerressen

In the changing construction environment clients are searching for new technology to complete their projects in shorter times. Manufacturers are therefore developing solutions to speed up established construction methods. The significant progress in recent years with the development of increasingly powerful drilling rigs is providing piling companies increase options for the execution of specialist foundation projects. The double rotary drilling methods are primarily used for the construction of pile walls as support for deep excavations. Typically these retaining walls are designed and installed as cased piles using the established Kelly drilling mode. However, more recently it is more popular to undertake these projects with the Cased Continuous Flight Auger (CCFA) system. This paper provides an overview of drilling with double rotary methods, in particular the monitoring during installation.

Jan 1, 2009

By Jeongbok Seo

This paper describes successful application of driven tapered-steel-pipe piles for two large-scale projects in the New York metropolitan area: Rego Park Mall, Rego Park, N.Y. and 164 Kent Avenue, Brooklyn, N.Y. The combination of side friction and end bearing resistance produced by tapered-steel-pipe piles has been well-recognized as greater than the side friction and end bearing resistance by pipe piles. Forty-four tapered piles were driven and tested at these two sites. Design pile load for the two sites was 260 kips for Rego Park Mall and 400 kips and 300 kips for 164 Kent Avenue. To measure the pile-drive hammer efficiency, the compressive stress in the pile, and to estimate the ultimate bearing capacity of the pile, dynamic load testing using a Pile Driving Analyzer (PDA) was conducted on index piles at the sites. Subsequent to the field testing, data analysis using the Case Pile Wave Analysis Program (CAPWAP) was conducted. Restrike PDA analysis and full-scale static load tests were performed on the selected test piles. Test piles at the project sites exhibited significant time-dependent increases in bearing capacity caused by the effects of "set-up" or "soil freeze." The dissipation of excess pore-water pressure in the soil, which had been disturbed and remolded by driven pile, was generally considered the primary cause of set-up. The increase at the subject sites ranged from 100 to 300 percent of the capacity measured at the initial driving. This paper discusses the results of various types of load testing on tapered piles and the set-up effects by comparing PDA test results acquired during and after pile driving. Finally, an empirical relationship for the New York metropolitan area has been offered for quantifying set-up.

Jan 1, 2008

By Peter J. Nicholson

Recognition of the liquefaction susceptibility of dam embankments has been heightened since the San Fernando Dam near failure incident in 1971. Both the downstream and upstream slopes of dams can be at risk for slope failure that can lead to breaching of the dam during or after a seismic event. Many dams have been remediated by various means such as the installation of stone columns or by excavation and replacement of the liquefaction susceptible material. Recent engineering and technology advances in equipment and materials has shown that construction of shear walls to the appropriate depths and at the right center to center spacing may be an economical alternative to the more traditional methods. Recently, the downstream embankments of at least 4 dams, from South Carolina to California, have been, or in the process of being remediated by the use of shear walls. The method of installation has been either multi-axis Cement Deep Soil Mixing walls or walls constructed by the use of trench excavation under self-hardening slurry. Four case histories of dam remediation are discussed, three by multi-axis paddle auger CDSM equipment one with the use of self hardening slurry trenches.

Jan 1, 2008

By W. Morgan NeSmith

"The DFI ACIP Pile Committee, in conjunction with the Florida DOT, completed an ACIP Pile installation monitoring and performance test program in late 2016 to advance the inclusion of ACIP piles in future specifications for bridges by state agencies. Piles of different diameters were installed for compression, tension and lateral testing, and one pile was extracted for visual inspection. This paper presents the pile installation, non-destructive testing and load test results of the program.INTRODUCTION The Deep Foundations Institute (DFI) Augered Cast-In-Place (ACIP) Pile Committee performed a ACIP pile installation and test program in the fall of 2016 to demonstrate a fully monitored installation of 18-in and 24-in diameter ACIP piles. The program included automated and manual installation monitoring, Thermal Integrity Profiling, compression, tension and lateral load testing (including monitoring of strain gages embedded along the compression pile shaft), and post-testing extraction of an installed pile for visual inspection.PROJECT DETAILS AND FIELD EXPLORATION A general program location map along with an aerial view of the property in Okahumpka FL is shown in Figure 1. Two Cone Penetration Tests (CPT) were performed at initial reaction pile locations R-6 and R-8 (Figures 2 and 3) The results from CPT R-6 indicated very loose soil conditions at depths below 55-ft, indicating potential relic sinkhole conditions. The test layout was subsequently rotated and moved south of CPT R-8.TEST PILE INSTALLATION DETAILS Seven piles were installed to either 40-ft or 60-ft below grade. Thermal Integrity Profile (TIP) wires were installed in all piles but varied to include one wire each attached to a steel center bar or one wire attached to the steel center bar AND four additional wires (each) attached the steel reinforcing cage installed in these piles. Additionally, the 24-in lateral and compression piles had four steel or PVC casings installed next to the TIP wires for testing by thermal probe and/or wire inserted into the casing."

Jan 1, 2017

By Glen M. Bellew, James F. Mehnert

"The Kansas City District-United States Army Corps of Engineers has completed the design modification of a pile supported floodwall located along the Missouri River in Kansas City, Kansas. This deep foundation supported floodwall protects over 2 billion dollars in infrastructure, is approximately 17 ft (5.2 m) tall and is 1,446 ft (440.7 m) long. Design modifications included the addition of a row of drilled shafts and the addition of relief wells. Typically, deep foundation design is controlled by total stress analysis and undrained soil strength. Neither controlled design at this site, where effective stress and drained strength controlled. During high river stages, artesian pressures develop, leading to a reduction in both effective stress and pile capacity. Deep foundation analysis software available to the designer does not allow these effective stress conditions to be directly entered, so a unique way was developed to account for them. A load test was performed to verify the design. During load testing, the supporting ground was unsaturated and had effective stress conditions different from those that controlled the design. A load test evaluation process involving unsaturated soil mechanics was developed and performed. This paper will share both the effective stress design process used and the load test interpretation process performed.INTRODUCTIONThe Fairfax-BPU Floodwall is part of the Fairfax-Jersey Creek Flood Protection Unit in Kansas City, Kansas. The floodwall was built in the 1940s and currently provides Missouri River flood protection for over 2 billion dollars of infrastructure in the Fairfax Industrial Area. The floodwall averages 17 ft (5.2 m) in height, is 1,446 ft (440.7 m) in length and is divided into 35 separate monoliths. The originally constructed foundation support for each of these monoliths typically consisted of three rows of seven tapered steel monotube piles, each roughly 20 ft (6.1 m) in length. All monontube piles are tipped in sand, well above bedrock."

Jan 1, 2016

By Abolfazl Eslami, Fatemeh Rostami, Sara Heidarie Golafzani, Mohammad Arabameri

Collapsible loess is classified as problematic soil found in most continents. The loess immediately collapses under stresses induced by axial compressive loading or the soil weight when exposed to moisture. In Iran, vast areas of the Golestan province are covered with aeolian loess deposits. This paper investigates whether the simultaneous effect of inundation and pre-loading in helical pile installation are operative and effective in improvement of Golestan loess. The effect of installation conditions on loess collapsibility is studied via two main approaches, i.e., field investigations and physical modelling. The experimental studies include installation of eight single helix piles in the Amirkabir University of Technology Frustum Confining Vessel, i.e., FCV-AUT. Also, four single helix piles with embedment depth of 3 m and diameter of 250 mm were installed in Golestan province and full-scale pile static loading tests were performed. The results indicated that the simultaneous application of crowd loading and water pressure during installation of helical piles results in better soil shear strength parameters. Moreover, high crowd stresses or low crowd stresses accompanied by water pressure during pile installation brings about similar load-displacement behavior of model piles installed in FCV-AUT and full-scale helical piles.

Oct 1, 2022

By A. A. Gupte

Auger piling system which was developed in the United States in the 1940's is gaining acceptance in many parts of the world. Although primarily used to support foundations, the system is very useful for many other applications such as soil anchors, temporary and permanent earth retention systems, restricted headroom piling and underpinning of existing foundations. In this paper, review of current construction design techniques for the Auger piling system for earth retention and underpinning of structures is presented.

Jan 1, 1989

By H. S. Radhakrishna

Foundations supporting power transmission and communications towers are subjected to both compression and uplift loads, often of a cyclic nature. Some novel foundations, combining the beneficial features of grouted and helix anchors with that of compression piles and grillages, were developed by Ontario Hydro during the construction of high voltage transmission lines in Ontario, Canada. In addition to meeting the load requirements, the foundations permit easy installation in swampy areas and also minimize impact on environmentally sensitive terrain. This paper describes the features of these composite foundations and outlines the performance criteria used for their design and installation on the basis of load test results.

Jan 1, 2010

By D. Vanni

Constructing new infrastructure in urban areas increasingly entails the use of sophisticated techniques for soil improvement in order to minimize surface disturbances in adjacent areas and damage to existing structures. In Naples, at the new Piazza Garibaldi subway station, TREVI built a 45 m deep shaft using a hydromill, and utilized soil freezing for the excavation of the four station's tunnels, fifty meter long, located approximately 30 meters below the water table. An innovative use of directional drilling was specially developed by TREVI to successfully complete this challenging job.

Jan 1, 2006

By Ali Bouafia

Five full-scale horizontal loading tests of piles carried out by the LCPC in France are interpreted in order to analyse P-Y load-transfer curves. The experimental piles are either bored or jacked into quite homogenous sandy soils and instrumented by strain gauges for measuring bending moments along the pile. Successive differentiation and integration of bending moment profiles have led to derive respectively lateral soil reaction and displacements then to construct the load-transfer P-Y curves. The initial horizontal lateral reaction modulus was derived from these curves and shows linear variation with depth in accordance with Gibson soils profiles. P-Y curves are validated by back-computation of the pile on the basis de these curves and the horizontal reaction modulus was compared to the recommendations frequently used in pile design practice.

Jan 1, 2002

By James D. Hussin

The Florida limestone is a relatively soft rock which presents many challenges to engineers when designing deep foundations. One alternative is micropiles which have grown significantly from their early days as very small diameter, light capacity elements. Also known as minipiles, pin piles, needle piles or root piles, micropiles offer an attractive deep foundation alternative for sites with tight access, low headroom, and where difficult subsurface conditions or obstructions necessitate a small diameter, high capacity deep foundation. The ability to confirm the competence of the limestone bearing formation by drilling in a rock socket has made micropiles a growing deep foundation selection in Florida.

Jan 1, 2003

By Barry C. Roth

A Real Time Automated Remote Reading Electrolytic Tilt Monitoring System was effectively deployed for monitoring an existing five story brick building during underpinning, shoring and excavation operations for a directly adjacent thirty-foot deep excavation. The monitoring system was comprised of four sets of uniaxial electrolytic tilt meters connected to a Campbell datalogger with multiplexer, cellular modem and solar power. The excavation was for the foundation and underground parking as part of a new 55 story tower complex. Challenges to the contractors and to our monitoring personnel which were addressed included a tight urban site contemplating property line to property line new construction with directly adjacent old existing buildings, buried concrete foundations from former site use, cohesionless pervious sandy soils and high groundwater. Highly variable and diurnal ambient temperature regimes due to adjacent building shadows required careful corroboration and application of temperature corrections to the raw data. Earth tides were suspected on a very small scale and investigated by correlation between the data and the local sinusoidal tidal ephemera. Incidental inadvertent contractor interference with the instruments during underpinning due to site constraints was readily detected.

Jan 1, 2007

By Pier Luigi Iovino

As Technical Director of the Naples, Italy based Fondedile, a geotechnical construction firm specializing in static restoration of structures, Fernando Lizzi, Ing., devoted over 30 years to the pursuit and advancement of static restoration and subsoil strengthening. Seismic events, construction of new structures on polluted and/or unstable soils in urban areas, and a need to carefully preserve and restore delicate, war-damaged historical structures, manifested the need for underpinning projects. Traditional construction methods and approaches, such as underpinning with additional foundation masonry, were not suitable and would have further jeopardized the stability of the structures. The introduction of the palo radice (root pile) revolutionized the field of underpinning. At the time of the first application of micropiles, the industry standard was driven piles. The drilled micropile was conceived and first implemented in the early 1950s, as an innovative means to underpin sensitive, historic structures and structures in urban areas. Specifically, the new construction technique was conceived as a less expensive alternative, designed to accept structural loads, be installed in limited access areas, in varied working and sub-surface conditions, which did not involve changing soil characteristics, and had minimal disturbance to the structure being underpinned, or to adjacent structures.

Jan 1, 2003

By J. W. Slatter

Cast in situ screw piling techniques (both displacement and non displacement) have seen considerable growth in recent years due to competitive production rates, low noise and vibration free installation. However the discussion on the mechanics of auger installation, which has implications on the installation effects and installation forces of screw piling augers, has been almost exclusively targeted towards non displacement techniques and in particular continuous flight augers (CFA). This paper discusses the historical development of the understanding of screw piling auger mechanics in sands and presents a new theoretical model to predict the soil transport and displacement characteristics of both displacement and non displacement augers with variable geometry.

Jan 1, 2000

By Issa S. Oweis

Two Towers are currently under construction in Central Moscow in the Russian Federation. Building A is a 96 story tower and Building B is a 65 story tower. The columns in both structures bear on a thick concrete mat that is supported on drilled shafts, 1.5 m in diameter. The shafts derive their capacity from weak limestone with layers of marl. Assigned allowable shaft loads were initially based on rock strengths that were later verified by load tests using the Osterberg Cell. One of the load tests was carried to near failure which allowed refining socket friction values that were later used in the design of Building A. All shafts were advanced using an auger and concrete placed in the dry. Grout tubes were placed with the reinforcing cage which allowed grouting of the limestone in contact with the shaft. Load sharing between the shafts and the mat was approximated using published methods as well as site specific finite element analysis. This paper covers the methodology of design, analysis of the Osterberg results to derive non-linear stiffness of the rock and differences between finite element analyses and results by approximate methods.

Jan 1, 2007

By Donald A. Deardorff

The capacity of a helical pile can be determined analytically using the individual bearing or cylindrical shear methods which are dependent on soil strength parameters and helical bearing area. The torque correlation method is widely used in the helical industry to determine the capacity during installation by monitoring torque during the final seating of the helicals. This method has been shown to be a better predictor of strength than the individual bearing or cylindrical shear methods. To determine capacity using the torque correlation method, the final average installation torque (ft-lbs) is multiplied by an empirical torque correlation factor (Kt, ft-1). Kt values have been well documented for square bar shaft helical products and can vary from about 3 to 20 ft-1 depending on pile geometry and soil type. A default value of 10 ft-1 is generally used for all square shaft sizes and soil conditions. Less research has been done on determination of Kt for round pipe shaft helical products. Studies have indicated that factors which affect Kt include soil type/strength, number of helical plates, helix spacing, helix pitch, depth of embedment, downward pressure (crowd), shaft diameter (round pipe) and load application direction while other studies have discounted some of these factors as inconsequential. This paper reviews past research findings regarding Kt determination for square and round pipe shaft helical products and presents a case history of round shaft helical pile installations in Chicago clay which resulted in much lower than expected Kt values.

Jan 1, 2007

By W. Morgan NeSmith

Drilled displacement (DD) piles often develop significantly larger unit shaft resistance values than other drilled or augered pile systems in coarse grained materials. Minimal vibration and limited spoil development are also associated with DD pile installation and these factors are frequently additional financial and/or environmental benefits of the system. The application of DD piles in North America dates to the mid-1990s and their use in the Midwestern United States has been significant, particularly in the past 10 years. The authors have collected an extensive database of DD pile performance in the United States. The alluvial and glacial deposits of the Midwestern U.S. provide conditions where drilled displacement piles perform very efficiently when compared to coastal and residual geologies. This paper presents a summary of the authors? experience regarding installation and performance of DD piles in the Midwestern U.S. Information presented includes summary presentations of DD performance across a range of site conditions as well as a discussion of the relationship of DD performance and installation effort in the Midwest as compared to other geologic settings in the U.S.

Jan 1, 2009