Search Documents

By H. Soto, J. Jara, F. Nava

A method has been developed to recover cyanide and copper from cyanidation effluents contaminated with thiocyanate and copper-cyanide complexes. Copper is precipitated as copper thiocyanate or as copper cyanide depending on pH and the concentrations of thiocyanate and cyanide present in the effluent. The copper precipitate presents good dewatering characteristics and can be easily separated from the effluent by thickening and filtration. The solution containing the bulk of the cyanide is then oxidized with ozone to transform the remaining thiocyanate into cyanide. This results in a regenerated solution rich in free cyanide that can be recycled to the cyanidation process. Careful control of the pH of the solution is required. First pH of the effluent is lowered to optimize the precipitation and oxidation stages, then the pH is restored to an alkaline value to regenerate the cyanide solution. Recoveries of over 96% copper are obtained. Free cyanide in the regenerated solution corresponds to up to 160% of the total cyanide contained in the original impure effluent. (The balance being accounted for by the cyanide obtained by the oxidation of thiocyanate). The efficiency of the thiocyanate oxidation stage is 85% to 90%. The method has been demonstrated at bench scale with effluents of various cyanidation plants of northern Quebec. A preliminary economic evaluation indicates that the procedure would be profitable for effluents rich in copper and thiocyanate. This is the case for most barren bleeds of Merrill Crowe and heap leaching operations and also certain CIP tailings of gold ores containing copper impurities. Environmentally the procedure is a better alternative than the current detoxification methods based on the oxidation of cyanide that do not allow for copper recovery and that have difficulties in producing a final effluent with acceptable levels of contaminants such as ammonia, thiocyanate and copper.

Jan 1, 1996

By M. Mirnezami, J. A. Finch, M. S. Hashemi A.

The surface of -30µm silica suspension (2% v/v) treated with 100 ppm Mg2+ at pH 11 was fully coated with Mg(OH)2. Under this condition, the silica is strongly positively charged (+30 mV) and the suspension is dispersed. Subsequent addition of Ca2+ promoted aggregation and reduced the surface charge. At this pH calcium is present as Ca2+ and CaOH+, i.e., positively charged ions interacted with the positive surface. Aggregation by a chemical bridging mechanism is proposed. The observation may be relevant to the widespread practice in mineral processing of adding lime to promote aggregation and settling in concentrate thickeners.

Jan 1, 2004

By J. Shahabpour

"Abstract - Breccias with angular and rounded clasts of a late-mineralization, ""barren"" hornblende porphyry dike set within a comminuted matrix consisting of rock fragments and quartz, cemented by quartz and K-feldspar of hydrothermal origin is observed in diamond drill cores from the Sar Cheshmeh porphyry copper deposit. Studies of age relationship between vein types, phyllic-altered clasts and the breccia groundmass suggest that the brecciation is a late event. The breccia clasts record evidence of hydrothermal reaction between the clasts and fluids responsible for the brecciation.Formation of bornite, in the breccia clasts of the originally barren hornblende porphyry dike, and in the breccia matrix, along with the scarcity of bornite in the Sar Cheshmeh deposit itself suggest involvement of fluids which are later and of different composition from the fluids responsible for the known mineralization at Sar Cheshmeh. These later fluids may be related to a later plutonic event and suggest the possibility of a later, and concealed deposit."

Jan 1, 1994

By Yves Bellemare

Entre 1983 et 1997, l'exploitation de la pierre de taille au Québec a été marquée par l'émergence et la consolidation de plusieurs nouvelles variétés de granit, provenant exclusivement ou presque de la Province de Grenville. Le Québec demeure toujours le principal expéditeur canadien de granit dimensionnel, avec des expéditions annuelles représentant près de quatre-vingt-dix pour cent des expéditions totales canadiennes de granit brut et transformé. La production annuelle de granit brut oscille, depuis 1994, autour de cent mille tonnes métriques. Cette production a plus que doublé de 63 000 à 140 000 tonnes métriques entre 1981 et 1990, mais elle a connu une chute importante en 1991 (67 000 tonnes métriques); cependant depuis 1994, elle est en forte progression (Ménard, 1998). En 1983, le granit dimensionnel était extrait de plus de vingt-cinq carrières, dont les trois quarts se localisaient dans la Province géologique de Grenville. Comparativement, en 1997, le Québec comptait trente-sept carrières actives, dont trente-cinq dans le Grenville (Gaudreau et al., 1998). Cette concentration des carrières dans la Province de Grenville s'explique par la demande accrue de nouveaux produits au fil des ans et par le potentiel élevé de découvertes de nouvelles variétés dans cette Province géologique. L'accessibilité au territoire, toujours plus grande, a facilité la mise en production de carrières favorisant la diversification des produits. Le ministère des Ressources naturelles du Québec (MRNQ) a consacré depuis 1980, beaucoup d'efforts dans la recherche de nouveaux gisements et de nouvelles variétés. En plus des programmes de subvention destinés aux prospecteurs ou aux compagnies, le ministère a réalisé des campagnes d'inventaire de pierre de taille, de pierre concassée et de pierre d'enrochement pour en connaître le potentiel géologique et à orienter les recherches futures (Nantel, 1983; Nantel et Martignole, 1991; Bellemare, 1995a, b, c, d, e, f, 1997, 1998a and b; Bellemare et Petryk, 1996a, b, c and d). Cette étude donne un aperçu des différentes variétés de pierres extraites dans la Province de Grenville entre 1983 et 1997, les situe dans leur contexte géologique et en localise les principales régions productrices. Elle est une suite à l'article publiée par Nantel (1984).

Jan 1, 2001

By S. Malopheyev, I. Vysotskiy, R. Kaibyshev, S. Mironov

"In this work, the effect of pre-strain rolling on the annealing behavior of friction-stir welded 6061-T6 aluminum alloy was studied. To this end, the as-welded material was rolled to 10 or 20 pct. of thickness reduction prior to the standard post-weld T6 heat treatment. Three rolling directions were the 3-mm thick sheet were considered: along the welding direction, perpendicular to the welding direction, and at the angle of 45° to the welding direction. At relatively low pre-strains (10 pct.), the annealing behavior was found to be very sensitive to the rolling path, and rolling along the welding direction was most effective in suppressing abnormal grain growth. On the other hand, increasing the pre-strains to 20 pct. of thickness reduction inhibited abnormal grain growth irrespective of the rolling path.INTRODUCTION Heat-treatable wrought Al-Mg-Si alloys are widely used due to attractive combination of strength, ductility, excellent corrosion resistance and low cost (Polmear, 2006). To provide the optimal balance of mechanical properties, these materials are typically commercially available in appropriately work- and precipitation-hardened conditions (Polmear, 2006). During conventional fusion welding, however, the prior strengthening effect is totally lost due to elimination of the work hardened structure and dissolution of the strengthening precipitations. An innovative friction-stir welding (FSW) technology may partially overcome this problem. Due to the solid-state character of this process, which involves very large strains, the welded material is characterized by fine-grained microstructure with moderate-to-high dislocation density, and thus the prior work hardening effect may be preserved or even enhanced (Threadgill et al., 2009; Mishra & Ma, 2005). However, heat input associated with FSW inevitably leads to dissolution and/or coarsening of strengthening precipitates, thus giving rise to the undesirable material softening. In an attempt to restore the strength of the friction-stir welded material, the standard T6 post-weld heat treatment has been applied, but this approach was found to lead to abnormal grain growth (Malopheyev et al., 2016; Mironov, 2013, Mironov et al., 2015)."

Jan 1, 2018

By L. Li

Backfill is increasingly used in underground mines, as it can help reduce the environmental impact from mining operations. However, the primary objective of backfilling is to provide safe working space for miners, by improving ground stability conditions. As cement is often added to the backfill, a critical issue is the determination of the required backfill strength (cohesion) due to the binder. This value is usually obtained from a solution proposed by Mitchell and co-workers, in the early 1980?s, for stopes with an exposed backfill face. This paper presents a brief review of the Mitchell et al. solution, with some of its main limitations. Some of the recently developed solutions for backfill design are then summarized and discussed.

Aug 1, 2013

By Hassan El-Shall, Ayman El-Midany, Patrick Zhang

Bench and pilot scale testing results suggest that significant improvement in dewatering characteristics of fine particles could be obtained by the addition of fibrous materials. Case studies involving flocculation and dewatering of wastes from phosphate, bauxite, and kaolin processing plants are presented in this paper. Several dewatering techniques were investigated, including sedimentation thickening, filtration, centrifugation, dewatering on screens, and seepage-induced dewatering and consolidation. Advantages and limitations of commercial application of some of the developed techniques arc discussed.

Jan 1, 2004

By A. Azizi, P. Blatter, A. Bouajila

ABSTRACT In-situ monitoring of gold dissolution by means of a rotating electrochemical quartzcrystal microbalance unveiled dramatic decreases in gold leaching from sulphide-rich ore after 360 minutes in an actual cyanidation circuit. Pre-oxidation was effective in enhancing gold extraction by preventing a passive film from forming on gold surfaces. This work aims to highlight efforts undertaken to determine (1) how gold cyanidation is limited by passivation, (2) what reactions and mechanisms are involved during sulphide-rich ore cyanidation, and (3) how peroxidation efficiency of an industrial sulphide ore is controlled by galvanic associations between its sulphide constituents.

Jan 1, 2013

By C. Bazin

"Discrete transfer functions which use the grinding circuit feed tonnage to predict mass flowrates at reagent addition points in the flotation circuit were calibrated using a dynamic grinding/flotation simulator. Predicted values are multiplied by g/t ratios to calibrate reagent flow. The transfer functions are currently integrated into the distributed control system at Les Mines Selbaie.INTRODUCTIONThe development of adequate tools for the control of flotation processes is a continuous challenge. Since the early 1970's there have been numerous publications dealing with practical applications of flotation process control. A review of that literature shows that basic feedback and feedforward controls are the two preferred strategies for flotation processes. Some advanced control schemes started to emerge (e.g. Zaragoza and Herbst, 1988). Feedforward and feedback aim at reducing the effect of the following flotation process disturbances (e.g. McKee, 1991):0 Changes in throughput;0 Changes in feed grade;0 Changes in particle floatability (size, liberation, surface oxidation ... );0 Deliberate changes of set-point;Feedforward strategy acts on manipulated variables, mainly reagent addition, to attenuate the effect of disturbances such as changes of feed rate and grade. The feedforward strategy is driven by measurements of disturbances. Feedback control acts to compensate unmeasured disturbances, such as ore floatability, and to bring process variables to targeted set-points of concentrate or tails grades. The feedback control action is driven by set-point error, caused by either a deliberate change of set-point or unaccounted disturbances.This paper proposes a way to improve feedforward control schemes by addition of a simple model of solids transportation. The feedforward strategy considered in this paper is of ratio type, i.e. the manipulated variable is changed according to a predefined ratio between this variable and the measured disturbances. A typical example is the ratioed reagent addition to mass flow of ore."

Jan 1, 1993

By F. Khomamizadeh

In this study, deep cryogenic treatment was applied to A319 cast aluminum samples. Although the cryogenic treatment didn't have any significant effect on mechanical properties of the well degassed and fluxed samples, but the tensile strength of the samples containing a considerable amount of gas and shrinkage defects was improved surprisingly, This improvement was attributed to the strengthening of the a-aluminum matrix which slows down the propagation of the existing defects. There was no significant increase in the hardness after cryogenic treatment, The abrasion resistance of the alloy was improved after cryogenic treatment, by developing a homogeneous protector shield, composed of abrasive grains penetrated into the soft aluminum matrix and kept tight.

Jan 1, 2005

By Jing Chai

The Cenozoic unconsolidated strata with the thickness of 100 to 240m in the east area of China are composed of clay, sandy clay and hardpan, etc. Numerous shafts of the coal mines in these areas have been damaged to various degrees since 1987, with the main reason for this being the subsidence of the super-thick unconsolidated strata. To prevent the continuing settlement deformation of unconsolidated strata caused by groundwater removal, long-term water injection through multiple boreholes controlled the settlement deformation of unconsolidated strata. A new type of fiber Bragg grating (FBG) sensing system was successfully used for real-time strain monitoring of the unconsolidated strata during water injection at a coal mine in China. A mathematical model for the compression settlement induced strain calculation is proposed which can assist understanding of the effect of water injection on the ground. With the increase in water injection, the unconsolidated strata compressed state was improved by the transition of the stress state from compressive to tensile stress. The wavelength change of fiber Bragg grating sensors corresponded with the trend of the water level in the same strata. Engineering practice indicates that these sensors can normally, safely and reliably survive conditions associated with hydrous unconsolidated strata. The FBG sensing can be used for continuous lifetime monitoring of the system, starting with real-time monitoring during low-pressure water injection process of multi-borehole. The results will give important guidance for water injection and mastering stratum subsidence.

Aug 1, 2013

By M. Uszko

The paper presents the conditions for determining the selection of methods for methane drainage in Polish hard coal mines. Various factors for the evaluation of methane drainage performance are used, including the methane drainage effectiveness ratio. However, as will be discussed there are limitations to the methane drainage ratio approach resulting from the characteristics of the deposits extracted in Kompania Weglowa S.A. coal mines.

Aug 1, 2013

By D. R. Nagaraj, Napoleon Tercero, Raymond Farinato

"Several studies conducted recently have shown that molybdenite flotation from Cu-Mo ores is adversely impacted in sea water at pH >~ 10.0 irrespective of the pH modifier; under the same conditions Cu sulfide flotation is relatively unaffected. This has been attributed to the presence of Mg2+ ions and their hydrolysis products in the sea water which adsorb and precipitate on molybdenite surfaces as Mg(OH)2. However, why and how Mg(OH)2 impacts only molybdenite flotation in the complex flotation pulps containing a multitude of minerals is not understood. The work presented in this paper probes the interface and interphase regions near the edge and basal planes of natural molybdenite (MoS2) in aqueous solutions and flotation pulps, particularly in the presence of copper ore pulp and added Mg2+. Differences in interaction of metal ions and their hydrolysis products (Mg2+, Mg(OH)+) were measured on the two faces of this anisotropic mineral. How those differences relate to molybdenite floatability and the impact of aqueous solution chemistry are discussed.INTRODUCTIONWater resource management is an important sustainability challenge in mineral processing. In view of the shortage of fresh water in many parts of the world, mineral processing plants are evaluating alternative sources. Seawater flotation has received much attention recently and there have been several important studies reported in the literature, particularly for the processing of Cu-Mo ores (S. Castro, 2012; S. Castro, Rioseco & Laskowski, 2012; S. Castro et al., 2012; Laskowski & Castro, 2012; Ramos, Castro & Laskowski, 2013; S. Castro & Laskowski, 2013; Laskowski, Castro & Ramos, 2013; Nagaraj & Farinato, 2014; S. Castro, Uribe, & Laskowski, 2014; Veki, 2013). The main conclusions from these studies on Cu-Mo ores in seawater at elevated pH were: a) flotation recovery of Cu sulfides is either unaffected or only marginally reduced, b) molybdenite recovery is adversely affected in seawater at pH values necessary for rejecting pyrite (i.e. pH > 10 to 10.8 depending upon particular system), and c) the precipitation of Mg2+ in seawater as Mg(OH)2 is responsible for the adverse effect on Mo flotation. In order to further investigate the individual effects of Mg2+ and Ca2+ on molybdenite depression in Cu-Mo ore flotation, Nagaraj & Farinato (2014) conducted flotation tests wherein individual metal ions were spiked into tap water during grinding of Cu-Mo ores. They showed the strong adverse effect of Mg2+ addition on Mo recovery and, to a lesser extent, on Cu recovery when pH > 9.5. Under similar conditions, Ca2+ had virtually no effect on either Cu or Mo sulfide flotation. Figure 1 below shows the previous results for Cu- Mo ores in tap water and the effect of addition of Ca2+ and Mg2+ ions. Note that in seawater the adverse effect of Mg2+ on Cu recovery was much smaller than that in tap water (Nagaraj & Farinato, 2014; Figure 4a and 4b and Table 4 therein)."

Jan 1, 2016

By W. Hunka

PACIFIC PETROLEUMS, Ltd. first discovered commercial quantities of gas in the Peace River area in 1952. Development of gas wells in this area is quite ex-pensive due to low penetration rates. To improve the economics, the potential of the wells in many cases had to be increased. At that time, well stimulation was still in its infancy in Canada and in this area, in particular, no treatment of any consequence had been attempted. Therefore, trial-and-error was the only means available to determine the stimulating technique that would give optimum results. Various fluid treatments were available and these were used wherever the application was warrant-ed. This paper covers acid fracture and explosive treatments as carried out on various gas-bearing horizons.

Jan 1, 1958

By C. K. Wilton

"The Agnew Lake uranium deposits were discovered in 1953 following the discovery of the Elliot Lake deposits to the west. The original property was optioned to Kerr Addison Mines Limited who added additional claims by staking. Agnew Lake Mines Limited was incorporated in 1967 to develop the property and a shaft was sunk to 1040 metres and five levels developed before work was suspended due to low uranium prices at the end of1970.In 1974-75 the mine was dewatered and production started in 1977. By 1978 reserves were estimated at 10,000,000 tonnes averaging 0.35 kg. U10 , per tonne. Underground operations were terminated in 1980 although a uranium leaching operation was continued until early 1983.The deposits lie near the contact of Huronian metasediments with underlying Algoman granite. The sediments consist of arkose, conglomerate, argillite and quartzite with the uranium mineralogy mainly confined to oligomictic quartz pebble conglomerate. The higher uranium values are related to conglomerate with highest percentage of pebbles. The chief uranium minerals are uranothorite and monazite. It is of interest that the uranium thorium ratio differs appreciably from that of the Elliot Lake deposits. This fact along with the fact that the Elliot Lake sediments were deposited by paleocurrents from the northwest whereas the Agnew Lake sediments were deposited by paleocurrents from the northeast indicates widely separate sources for the deposits. It is suggested that the Agnew Lake uranium deposits are syngenetic placers deposited under anoxygenic atmospheric conditions."

Jan 1, 1986

By Amir Asadi

Various damage modes that evolve with time in polymer composite laminates, such as transverse cracking, vertical cracking, delamination, and fiber fracture, as well as the interaction among them, influence the time-dependent degradation in modulus (creep) and strength (creep rupture) of polymer composite laminates. This study is focused on modeling the time-dependent evolution of transverse cracking in [90] plies of a multidirectional polymer composite laminate [0m/190n]. This model uses a two-dimensional variational analysis to determine the stress state at any given creep time. The elastic stored energy, determined using this stress state, is compared with a critical energy for fracture to determine the crack evolution with creep time. Model predictions are compared with experimental results to validate the model.

Jan 1, 2010

By Luino Jr. Dell'osso, Richard L. Every

The enormity of the methane-in-coal problem is discussed, with a brief summary of the state-of-the-art. Laboratory techniques and data on the desorption of methane from Pittsburgh seam coal are presented and discussed and include the effect of time, temperature and vacuum. Under laboratory conditions, it was possible to displace 90 per cent of the residual methane by flooding the coal samples with carbon dioxide. Carbon dioxide was found to be three times more effective than air and almost five times more effective than helium.

Jan 1, 1972

By CIM CIM

Why Workplace Important! ?We need Diversity is to do more in the industry as a whole to encourage and support diversity. It has long been an industry of white dudes and we?re not going to survive if that?s how we continue to think.? ? Mark Scott, HR Superintendent, Vale Inco PURPOSE OF MINING FOR DIVERSITY ? Share best practices in the areas of HR Development ? Support industry in attracting, recruiting and retaining a diverse workforce ? Raise awareness of industry HR challenges and collaborate with stakeholders to develop sustainable HR practices

May 1, 2009

By Bradford C. Wesstrom

An overview of the challenges encountered at the Freeport McMoRan El Paso Copper Refinery with higher concentrations of antimony electrolyte will be shared. The observations will cover the detrimental effects on copper starting sheets, commercial cathodes and anode slimes. The study will show negative effects on quality and productivity. Experimental work will utilize a test cell to study the effects on electrolytes by different Antimony, Arsenic concentration and anode molar ratio. Best practices will be shared for producing high quality cathodes while effectively managing the detrimental effects of higher antimony electrolyte.

Jan 1, 2014

By D. Michaud, C. Bazin, S. Lévesque, L. Pérez-Barnuevo, H. Longuepée

In recent years, with the emergence of Geometallurgy, a great effort has been made to characterize ore resources as early and accurately as possible, to allow better design and a more efficient operation of mineral processing circuits. In this context, core logging plays an important role, since drill cores provide the first insight into the ore characteristics. However, to satisfy geometallurgical requirements, traditional core logging does not suffice. New tools and methodologies need to be developed for the automation of core logging and the acquisition of mineralogical data better related to mineral processing performances. In this paper, a methodology for the geometallurgical characterization of drill cores is proposed, based on the drill core textural patterns. Textural pattern is defined here as the macroscopic spatial arrangement of minerals. The Mont-Wright iron ore deposit (Quebec, Canada) is used as a case study. The first part of this work aimed at analyzing the potential link between the iron ores textural patterns observed in drill cores and their response to ore processing, namely comminution and concentration. Preliminary results show similar performances in terms of energy consumption and heavy liquid separation for samples showing the same textural pattern. In the second part, this work seeks to develop a methodology for the automated identification of drill core textural patterns by the application of digital image analysis and discriminant function analysis. The results obtained show that this methodology is able to discriminate between the textural patterns identified at Mont-Wright with a good rate of success. Therefore, this work lays the foundation for the development of a new drill core characterization tool, which would allow for the early prediction of the iron ore behaviour during mineral processing through the identification of drill core textural patterns.

Jan 1, 2016