Search Documents

By Anivaldo Chevane, Leonardo Xerinda, Rogério Sendela, Andre Vilanculos

Moatize Coal Mine is located in Tete Province, in centre of Mozambique. The deposit contains Gondwana allochthonous coals, and has a large amount of mudstone and siltstone banding. Phosphorus levels in the coal can be high which impacts the use of the coals in steel making where phosphorus is considered a contaminant. The Chipanga seam in the Moatize deposit shows considerable variability, vertically within the seam and laterally across the deposit. The data available from the exploration work indicates that the phosphorus is predominantly present as Apatite but the Crandallite minerals also are significant. The concentration of phosphorus varies with coal particle density with the highest phosphorus levels found for the mid density coal which also shows the highest likely levels of apatite or fluorapatite. Crandallite minerals show higher potential concentrations in the Lower density coal..

Oct 3, 2019

By Stefano Baf

This paper describes the main technical and process solutions applied to the extrathick and wide slab caster built at Yingkou (Liaoning, P.R. of China), as well as all the features required to achieve the surface and internal quality targets.

Aug 16, 2017

By Giuseppe Pintaude

This study aims to evaluate the effect of specimen preparation on the dry sliding wear behavior of CA-6 NM stainless steel. Two different surface finishing manufacturing processes were applied: lapping and metallographic polishing. The wear tests were conducted in reciprocating ball-on-flat system, performed for two loads: 5 or 8 N. For all test conditions, hardmetal ball was employed as counterbody. The surfaces were evaluated using 3D interferometry technique to determine their surface roughness, including texture analysis regarding isotropy. Surface characterization results indicated the presence of texturing and preferential orientation, since the parameter Str was smaller than 0.5 for samples of both the studied conditions. Two distinct levels of isotropy evaluated through Str parameter were achieved: 0.13 for lapping and 0.3 for metallographic polishing process. It is clear from wear tests that the variation of average surface roughness is the key point for tribological behavior of CA-6 NM stainless steel.

Jul 31, 2018

By Thomas Höfler, Michael Auinger, Bernhard Linder

Gas-fired pusher furnaces are commonly used to heat steel slabs before hot rolling. Temperatures well above 1000 °C combined with an oxidizing atmosphere containing H2O, CO2 and O2 result in rapid oxidation of most steel grades. The resulting oxide scale and the chemistry of the metal-scale-interface are major determining factors for the occurrence of hot rolling defects. To better understand these phenomena, lab-scale trials were performed with two different steel grades in an electric tube furnace in the temperature range 1000-1250 °C, using an atmosphere of about 20 % H2O, 7 % CO2 and 3 % O2. Humidification of the gas was achieved by evaporation, using a custom thermostat with standard laboratory glassware. The resulting samples were prepared metallographically, using cold mounting under vacuum with taper section angles, and analyzed using light microscopy and SEM/EDS. The scale structure of the Si alloyed steel was highly dependent on the oxidation temperature due to the formation of eutectic liquid phases of FeO, Fe2SiO4 and FeAl2O4. Below the eutectic temperature, the scale of the Si steel appeared to be made up of three distinct areas: The external scale consisting solely of Fe oxides, the internal scale containing Fe2SiO4 and FeAl2O4, and an internal oxidation zone with SiO2 and Al2O3 in a mostly plain Fe matrix. Comparisons of the experimental results with simulations of the internal oxidation showed good qualitative agreement.

Oct 1, 2019

By Eduardo Cabral

A nova política de resíduos sólidos, imagem positiva da empresa, utilização consciente de recursos com a consequente redução de custos e preservação do meio ambiente têm levado as minerações e siderúrgicas a adotar uma gestão responsável com relação aos seus coprodutos. Em consequência, esses coprodutos (escorias e lamas da mineração, lamas de aciaria, pós da sinterização, calcinação, coqueria, carepas e outros resíduos da siderúrgica) estão sendo economicamente reintroduzidos no processo produtivo. Esse trabalho pretende fazer um resumo de possíveis tratamentos que esses materiais podem sofrer, como umectação, aglomeração, briquetagem, granulação, pelotização ou extrusão.

Aug 16, 2017

By Ismael Nogueira Rabelo de Melo

A adição de Fe-Nb em ligas com alto teor de carbono apresenta baixas taxas de dissolução devido à formação de uma camada carburada na superfície, exigindo longos tempos para dissolução dos carbonetos NbC no banho. Foi avaliada a eficiência da dissolução de Fe-Nb em pó pelo processo de simples adição em uma liga de Ferro Fundido Branco com Alto Teor de Cromo. No processo foram obtidas eficiências de dissolução em torno de 90% e os carbonetos NbC apresentaram em formas finas e em aglomerados.

Oct 30, 2017

By Diego Berti Salvaro

A morfologia, dimensões e composição química de tribocamadas são fortemente dependentes das pressões e temperaturas existentes no contato e oriundas das reações das superfícies entre si, com a atmosfera, com os lubrificantes e contaminantes presentes no contato. No presente artigo foi analisada a formação de tribocamadas em pares DLCaço inoxidável testados por 180, 500, 1000 e 2500 horas em atmosfera de gás refrigerante R134a sem a presença de óleo lubrificante. A caracterização foi realizada por microscopia eletrônica de varredura espectroscopia de energia dispersiva (MEV-EDS) (morfologia e composição química) e interferometria ótica de luz branca (dimensões). Nas análises por MEV-EDS foram identificadas tribocamadas que se apresentaram mais pronunciadas nas superfícies do aço inoxidável sendo as mesmas oriundas de transferências mútuas entre os pares tribológicos bem como oxidação. A espessura das tribocamadas, por sua vez variou de 100 a 500 nm. Os resultados revelam que as tribocamadas são quimicamente estáveis e que suas espessuras não variam significativamente após mil horas de ensaio.

Aug 16, 2017

By Edo Engel

Whereas only a handful of decades ago, typical blast furnace working volumes were below 1000 m³, such furnaces are currently designated compact or even mini blast furnaces. For certain business cases, however, small furnace sizes remain an attractive option. Decades ago, this size blast furnace would have produced a maximum of 0.3 Mtpa with its 600 m³ working volume over a campaign of up to four years. The current state of technology and operational know–how will allow a similarly sized furnace to produce over 0.7 Mtpa while achieving the multiple decade campaigns that have become familiar to steel producers in full sized operations. This level of productivity, but especially the reliability and supply security associated with mature technology, allows for integration into minimills or taking a first step towards a full scale BF–BOF integrated mill. Steel producers considering such scenarios, which are typically attractive for emerging economies, are confronted with fundamental decisions, one of which is for the technological basis for the compact or mini blast furnace to be included in the plant. This article addresses some of these decisions from an operations–based perspective. A small number of case studies is included.

Aug 16, 2017

By João Batista Ribeiro Martins, Érica Simões Rodrigues, Ramiro da Conceição do Nascimento Júnior, Marcos Tadeu D’Azeredo Orlando

In order to guarantee the quality of the sinter and process control some measurements are made such as RDI and FeO (Fe2+). However, the behavior of sinter during reduction in the blast furnace is not always understood, when it is analyzed only metallurgical, physical and chemical quality. Therefore, it is necessary to find alternative techniques to understand more this behavior. In this work four experimental trials were performed to obtain sinter samples with different FeO (Fe2+) contents. Optical microscopy was performed to identify and quantify the phases in sinter and to evaluate the magnetic behavior of each one, the Magnetic Susceptibility technique was used. The results obtained between Optical Microscopy, Magnetic Susceptibility and quality parameters were compared and then was identified that Magnetic Susceptibility may be an alternative to help the understanding of sinter behavior in Blast Furnace.

Oct 1, 2019

By Verônica Scarpini Candido

O uso cada vez mais frequente do poli metacrilato de metila (PMMA), muitas vezes em substituição ao vidro temperado, se deve a sua alta rigidez, praticidade, leveza e transparência. No entanto, as normas de fabricação atuais na indústria de polímeros recomendam testes específicos nesses materiais. O presente estudo tem o objetivo de testar mecanicamente as propriedades do material Polimetacrilato de Metila (PMMA) em condições que simulem um ambiente muito mais agressivo do que o usual. Para tanto foram realizados testes de espectroscopia na região do infravermelho (FTIR), análise termogravimétrica (TGA), testes de tração e impacto Izod, e análise por Microscopia Eletrônica de Varredura (MEV). Os resultados revelaram que o Polimetacrilato de metila (PMMA) manteve suas propriedades mecânicas em tração até a temperatura de 105°C. No que se refere à resistência ao impacto, a temperatura influenciou negativamente no desempenho desse polímero.

Oct 30, 2017

By Mathias Woydt

The tribological and mechanical properties of binderless and metal-bonded niobium carbides (8 or 12 vol.-% of Cobalt, 12 vol.-% of Fe3Al) are presented. Rotating disks made of niobium carbide bearing hard metals were mated against alumina (99.7%) under unlubricated (dry) unidirectional sliding tests (0,1 m/s to 12,0 m/s; 22°C and 400°C) as well as in oscillation tests (f= 20 Hz, ?x= 0,2 mm, 2/50/98% rel. humidity, n= 105/106 cycles). Microstructure and phase compositions were determined as well. The tribological data obtained were benchmarked with different ceramics, cermets, hard metals and thermally sprayed coatings, where NbC bonded with 8% and 12% Co presented above 8 m/s the lowest wear rates so far in such a benchmark. Binderless NbC (HP-NbC1) and the metal bonded NbCs exhibited low wear rates under dry sliding associated with high P?V load carrying capacities. NbC-based hard metal bonded with 12 vol.-% of Fe3Al resulted in a higher hardness level than for 12 vol.-% cobalt. The tribological profile established revealed a strong position of NbC bearing materials under tribological considerations and for closed tribosystems against established reference tribo-couples.

Jul 31, 2018

By Marcos Paulo da Silveira, Carolina Conter Elgert, Messias Prado de Almeida, Rafael Stella Galdino

Microalloyed steels have been intensely studied as an alternative to increase strength by grain refinement and/or precipitation hardening. Long steel products have a wide range of opportunities to apply well-defined principles of controlled rolling (CR) in order to increase strength and toughness with reduced costs. To evaluate the effect of microalloying elements as Nb and Ti with thermomechanical treatment, three conditions were tested: DIN 16MnCrS5 with hot rolling (HR), DIN 16MnCrS5 with Nb and CR and DIN 16MnCrS5 with Nb+Ti and CR. Austenitic grain size, obtained by direct quenching after rolling, has shown a decrease 32% with Nb addition, and 29% when Nb and Ti was added. Controlled rolling generated higher grain refinement and pancacked grains near the surface. When comparing ferritic grain size, controlled rolling plus niobium and titanium additions resulted in significant reduction of 35%. Yield strength increased 15% with microalloying and CR and more than 270% in impact toughness, even at -40°C.

Oct 1, 2019

By Pedro Jorge Walburga Keglevich de Buzin

The steel production in mini mills generates several process residues, among them there is the electric arc furnace dust (EAFD). This residue has as main elements Fe, O, and Zn, being classified as hazardous by the presence of Pb and Cd. Thermodynamic studies related to the formation of mineral species containing Fe, O and Zn elements were carried on due to the influence of these compounds in hydrometallurgical EAFD recycling processes. In recent years, a rise in the chlorine content of this residue was observed, mainly motivated by the increased use of scrap with polymeric impurities containing this element. In this work, based on computational thermodynamics tool FactSage, a general overview of gaseous and minerals species (found in EAFD) formed by Fe, Zn, O, Cl, H and C is shown – representing the organic origin of chlorine. For this study, the PVC polymer was used as the chlorine carrier substance which contaminates the EAF load.

Jul 30, 2018

By Francielle Santos Pereira, Alexandre Medeiros, Robson Ferreira Alvarenga, Willian Pimentel de Barros, Bruno Aquino Rocha, Evaldo Nogueira, Ewerton Ferreira Campos, Marcus Valério Magnago

Este artigo tem como premissa, apresentar a aplicação da inovação tecnológica, para melhoria da segurança nas operações Logísticas da ArcelorMittal Tubarão. Neste documento apresentaremos a Logística de estocagem e expedição de produtos, sua estrutura de funcionamento, e as operações executadas. Em seguida, explanaremos sobre as melhorias de segurança executadas com auxílio da inovação e tecnologia. Por fim, serão demonstrados os impactos provenientes dessas ações, para a execução do trabalho com menor risco às pessoas e equipamentos envolvidos no processo logístico de escoamento de produtos, destacando os benefícios que a tecnologia pode trazer para a logística no âmbito da segurança e produtividade.

Oct 1, 2019

By Ana Paula de Andrade Manfridini

A formação de nitretos na superfície de aços Interstitial Free (IF) nitretados a plasma em função da temperatura de tratamento foi investigada. Amostras de aço IF estabilizados ao Ti, laminado a frio e com shot peening foram nitretadas a plasma nas temperaturas de 450°C, 475°C e 500°C durante 4 horas. A camada nitretada resultante foi caracterizada por microscopia eletrônica de varredura (MEV), difração de raios-X (DRX) e método Rietveld. As imagens de MEV revelaram duas principais regiões na camada nitretada formada nas três temperaturas de tratamento: uma camada de compostos constituída de ?-Fe2-3N e ?’-Fe4N e uma camada de difusão apresentando uma matriz ferrítica com finos precipitados de ?’’-Fe16N2. Através da DRX, foi observada uma variação na proporção das fases ?-Fe2-3N e ?’-Fe4N. A partir de análises Rietveld, foi sugerido que a maior temperatura de nitretação facilitou a formação de nitretos ?-Fe2-3N, uma vez que a quantidade dessa fase aumentou de 475°C para 500°C. A presença deste precipitado com maior teor de nitrogênio sugere uma possível maior aplicabilidade dos aços IF.

Aug 16, 2017

By Kelen Juliane Mucelin

In order to better understand the tribological behavior of self-lubricating materials, Fe-Si-C matrix composites containing solid lubricants added during the mixing step were studied. The samples were produced by conventional powder metallurgy route, presenting total contents of 5%, 7.5% and 10% in volume of h-BN and graphite mixtures as solid lubricants. The composites were evaluated in terms of tribological properties, under reciprocating sliding conditions, and mechanical properties by using tensile tests. Additionally, the wear scars were characterized by Raman spectroscopy and scanning electronic microscopy. Higher total contents of solid lubricants greatly increased scuffing resistance however decreased mechanical properties. Furthermore, increasing h-BN contents reduces both properties. These results confirmed the applicability of such sintered composites as self-lubricating parts, reaching values up to 7000 N.m for scuffing resistance combined with ultimate tensile strength of 220 MPa.

Jul 31, 2018

By Luís Marcelo Marques Tavares, Gilvandro Bueno, Túlio MoreiraCampos

The HPGR development and application in the minerals industry resulted in an important increase in its application in iron ore pellet feed processing in the last decades. Vale SA was one of the pioneers in application of the HPGR in integrated plants, currently operating with six HPGRs in the pelletizing plants of Complexo de Tubarão (Vitória, ES). The work uses the mathematical model of the HPGR, proposed by Torres & Casali and modified by the present authors, to predict the performance of two industrial pellet feed HPGR units of the Complexo de Tubarão. Besides model validation, results of process simulations are shown in order to optimize the pellet feed pressing according to industrial demands, presenting different scenarios that are more attractive to HPGR operation. Simulations showed that it is feasible to reduce the specific surface area of the HPGR feed from 1770 cm²/g to 1570 cm²/g, allowing to produce a pellet feed of the same quality in its product (1911 cm²/g) and therefore reduce the work done by upstream ball milling.

Oct 1, 2019

By John Hinton

Electromagnetic based (EM) sensor technology has been shown to detect changes in the magnetic permeability of steel strip travelling down the run out table after rolling. Measuring below the Curie temperature, these changes can be interpreted in terms of the phase transformation from austenite (paramagnetic) to ferrite (ferromagnetic). These real time measurements provide a detailed insight into the changes in the structure at high temperature providing the steel producer with feedback on quality control, product consistency and product development. However unlike mill microstructure models, the sensor measurement provides a point reading at a distance through the cooling course. To map the transformation in more detail, a sensor array is required along the length of the Run Out Table i.e. to measure points on the austenite to ferrite transformation curve. This paper describes the process and metallurgical factors that should be considered in the optimum design of a sensor array, i.e. the number and location of the sensor heads. Examples of cooling strategies for different steel grades e.g. low carbon, structural and dual phase steels are used to demonstrate the importance of sensor location. In addition, the effect of variability within typical industrial parameters e.g. cooling speed, on the sensitivity of sensor output and location will be considered.

Oct 1, 2019

By Jean Viana Bahia, Antônio Adel dos Santos, Vicente Tadeu Lopes Buono

During cold rolling of Cr-Mo alloyed DP steel, considerable oscillation of thickness may occur. The literature points out that such occurrence is due to non-uniform cooling of the coil after the hot rolling process. Since the austenite transformation in this steel continues after coiling, the microstructure and, consequently, mechanical properties are very susceptible to natural variations in cooling rates associated with distinct positions of the coil. The influence of coil cooling conditions on thickness oscillation during cold rolling was evaluated in this work by using both industrial experiments and dilatometer tests. It was verified that an industrial coil presented large variation of mechanical properties associated with its heterogeneous microstructure. Consequently, thickness oscillation occurred during cold rolling. Dilatometer tests simulating hot run-out table and coil cooling showed that the austenite transformation is very slow under small cooling rates that occur after coiling. Thus, the slow transformation rate makes the coil very susceptible to environmental conditions around it during its natural cooling and is responsible for variation in mechanical properties of the coil. To ensure the formation of a more homogeneous microstructure in the whole coil, it is necessary either to make use of technologies that improves the cooling uniformity or to adjust the steel alloy design. The latter alternative has been done with relative success by using conceptions with lower amounts of Cr and Mo.

Oct 1, 2019

By Rafael Arthur Reghine Giorjão

Microestrutura e propriedades mecânicas de tubos de aço inoxidável superduplex SAF 2507 processados por soldagem por atrito com pino não consumível foram analisadas. Juntas de alta qualidade foram produzidas com sucesso utilizando ferramentas de nitreto de boro cúbico policristalino (PCBN), controle de força de 38 kN, velocidade de avanço de 50 mm/min, velocidade de rotação de 200 RPM. Ensaios de dureza e tração foram realizados, evidenciando aumento de dureza na zona de mistura e falha no metal de base. Simulações térmicas calcularam temperaturas globais máximas em torno de 1176 °C e diferentes ciclos térmicos ao longo da espessura da junta, conferindo diferenças microestruturais e mecânicas nestas regiões

Oct 30, 2017