Search Documents

By Andreas Orth

Outokumpu Lurgi Metallurgie has developed a process for the calcination and reduction of laterite nickel ore tines where the reduction of iron and nickel to the wustite/metallic states respectively, is performed in a fluidized bed reactor using reduction gas generated very cost effectively from natural gas in an autothermal catalytic reactor. As an option coal can be used as reductant as well as additional fuel. The process of reduction and calcination is very energy optimized. It uses the off gas from the fluidized bed reduction reactor, which still contains energy, to dry and calcine the nickel ore fines in a primary stage circulating fluidized bed (CFB) reactor. The product shows high metallisation of nickel and iron oxides reduced to the wustite stage. This results in considerable energy savings in smelting the prereduced product to ferro-nickel. Alternatively the product can be leached to produce nickel. Laboratory tests showed very high recovery of nickel and cobalt. Keywords: Fluidized Bed, Prereduction, Calcination, Ferro-Nickel

Jan 1, 2004

By Yuanbo Zhang, Zhixiong You, Daoxian Duan, Guanghui Li, Tao Jiang, Xiaohui Fan

"Presently, high-grade manganese oxide ores are usually utilized by a coal-based reduction roasting process. However, there were some obvious drawbacks, including serious environmental pollution, high energy consumption, etc. The reduction temperature is relatively high (850-900 °C). In this study, a kind of biomass, pine black charcoal, was used as a reductant to reduce low-grade manganese oxide ores. Under the optimal conditions of reduction temperature of 600~650 °C, roasting time of 30~45 min and ratio of ore to reductant 5:1, the leaching efficiency of manganese reached more than 98%. Compared with the traditional coal-based reduction process, the reduction temperature is reduced by 250-300 °C.IntroductionManganese plays a very important strategic role in the national economy, and it is widely used not only in the metallurgical industry, but also in the light industry, chemical industry, medicine, agriculture, etc [1]. The average grade of manganese ores in China is evenly about 21%, which belongs to typical low-grade manganese ores [2]. Therefore, large quantity of high-grade manganese ores is required to import in order to meet the rapid development of Chinese manganese industry. As reported, the conventional treatment of reduction roasting has been widely applied for processing manganese oxide ores, in which coals or reducing gases (CO, H2 or CHi) were usually used as reducers [3]. However, there were some insuperable problems, such as high energy consumption, poor operating conditions, serious environmental pollution, etc [ 4-9]."

Jan 1, 2013

By M. A. Cocquerel

The future economic necessity of mining copper ores with a high impurity content and increased environmental awareness will require closer examination of the distribution of arsenic within copper smelting processes. A generalized approach is developed which can be adapted to specific projects for the determination of an overall process configuration to satisfy all requirements in a cost effective manner.

Jan 1, 1983

By Waraporn Piyawit

Grinding sludge from the sintered neodymium-iron-boron (NdFeB) magnets production process was enriched with critical rare earth elements (neodymium, dysprosium and praseodymium), which can be up to 30% in the magnets. The demand of NdFeB magnets are simultaneously growing. Therefore, rare earths recovered from waste residue would reduce the demand of rare earth elements from primary sources. In this study, the feasibility of recycling rare earths through a hydrometallurgical process was investigated. The selective leaching of Nd from grinding sludge can successfully raise the rare earths concentration to 70%. The necessity of an oxidation pretreatment to improve the selectivity between Nd and Fe will be described.

By Jörg Wallner

In order to limit SO2 emissions, the Montanwerke Brixlegg AG has installed a desulphurisation plant with the primary aim of reducing the peak emissions from the copper converter that are of particular ecological concern. The author discusses the process requirements, the desulphurisation process selected and the results achieved.

Jan 1, 1996

By Z. Q. Chen, M. H. Loretto, Y. G. Li

"As-cast, As-forged, as-solution-treated, and solution treated and aged microstructures of Ti-15Mo (IMI205) with and without carbon were examined using optical microscopy, scanning electron microscopy .and transmission electron microscopy. Tensile testing was carried out at room temperature. It was found that carbon acts primarily as a titanium carbide former: Titanium carbides increase slightly the tensile strength, but decrease the ductility of IMI205. These observations are interpreted in terms of the titanium carbide morphology observed using SEM and TEM and the phase diagrams of Ti-Mo, Ti-C, and Mo-C.IntroductionIn a recent study on the development of a burn-resistant 13-Ti alloy, carbon was introduced· into the Ti-V-Cr system in order to optimise the mechanical properties. Research results[1, 2] demonstrate that carbon addition can refine the 13 grain size and improve the stability of the 13 phase in Ti-V-Cr alloys. The most attractive result is that carbon addition produced a marked improvement in the ductility of alloys when the carbon content is over 0.1 wt.% in this alloy system. Even after long exposure, the alloy with carbon addition maintains good ductility. One of the main reasons for the ductilising of the alloy is that titanium carbides can getter the oxygen from the 13 matrix.In view of the success of carbon addition in improving the properties and the stability of the Ti-V-Cr alloy, it is of interest to investigate the behaviour of carbon addition in other beta Ti-base alloys. The objective of the present work was, therefore, to assess the microstructures and mechanical properties of IMI 205, a metastable beta titanium alloy, with and without carbon addition using optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), wavelength dispersive X-ray (WDX) analysis, room temperature tensile testing."

Jan 1, 2000

By Yuanbo Zhang, Guihong Han, Guanghui Li, Tao Jiang, Zengqing Sun, Yanfang Huang

"Because of small specific surface area and poor ballability, vanadium/titanium-bearing magnetite is difficult for production of oxidized pellet. A novel organic copolymer binder, modified humic acid (MHA), has been authorized recently in China. Effects of the novel MHA binder on the quality of V/Ti-bearing magnetite pellets are studied in this paper. Experimental results show the MHA binder can obviously improve the strength of green pellet. Because of better heat endurance, the MHA binder pellet has a higher strength than Peridur pellet under the same preheating conditions. Moreover, TFe grade of pellet with the MHA binder is much higher than that of the bentonite pellet. The strength of preheated pellet containing MHA binder of 0.25%~1.0% meets the requirements of oxidized pellet production by grate-kiln process. Comparatively, MHA is a promising orgainc binder for iron ore pellets. Its price is only one tenth of Peridur price and about 3 times of bentonite price.IntroductionThe iron-making practices show that the use of pellet is beneficial to blast furnace life, productivity and fuel savings. Therefore, many iron-making plants have expanded the production of oxidized pellets in order to meet the needs of modern large-scale blast furnaces [1]. Presently, bentonite is widely used to improve the quality of iron ore pellets. The negative effects of using bentonite include decreasing total iron (TFe) grade and degrading the metallurgical properties of the final products [2, 3]. Many studies, therefore, have been conducted on the application of organic binders to overcome the weakness of the inorganic bentonite. In comparison with inorganic binders, one of the biggest strengths of organic binders is low residual silica content [4]. However, those studies showed that the economics of foreign organic binder addition into pellets was not attractive. For example, the compression strength of preheated pellets and roasted pellets are both too low, resulting in powder generation and ring formation in the industrial rotary kiln [3, 4]."

Jan 1, 2011

By C. H. Bucknam

A review of phase analysis methods used to characterize refractory gold ores is presented. Updating of assay methods using database technology, on-line instrument interfacing and response surface modeling is highlighted. The use of assay results to classify ores for metallurgical purposes is demonstrated.

Jan 1, 1987

By Jian Li, S. Penttila, W. Zheng

"Materials selection for Gen IV supercritical water reactor in-core components faces major challenges due to severe operating condition. Beside high-temperature mechanical properties, SCC and general corrosion resistance of commercially available materials are also major focuses in recent research. Recent reports suggest that certain types of surface modifications are beneficial to SCW corrosion resistance. In this study, the effects of surface modifications are investigated, and possible mechanisms for improved corrosion performance are discussed.IntroductionThe current Canadian pressure-tube supercritical water reactor (SCW) design specifies a core outlet temperature of 625°C under 25 MPa of pressure, with peak cladding temperature as high as 850°C. Challenges in materials selection include high-temperature mechanical properties, corrosion resistance, SCC resistance and radiation damage. Most of the SCW corrosion test results available are below 730°C. Early work by Allen [1] summarized the corrosion resistance of alloy groups including Ni-based super alloys, stainless and ferritic/matensitic (F/M) steels that can potentially be used for SCW reactors. F/M steels can only be used at low temperature sites (e.g. down stream piping). At 500°C and 25 MPa, F/M steels develop a thick but mechanically stable oxide layer. However, the long term stability of the surface oxide layer is largely unknown. Ni-based alloys appear to form very thin surface oxide, however pitting was observed in the vicinity of some intermetallic precipitates [2-5], and dissolution of major alloying components could pose significant problems for down stream piping [6]. In addition, concerns of Helium formation due to Ni transmutation prevented this alloy group to be used as fuel cladding. The corrosion resistant austenitic stainless steels (e.g. 316L) are found to be susceptible to localized corrosion such as pitting, intergranular attack and stress corrosion cracking (SCC) [7]."

Jan 1, 2012

By Jan Smit

Sulphidic copper concentrates are generally processed by pyrometallurgical means; while oxidative pressure leach processing of such materials has been shown to be technically feasible, there has traditionally been little incentive to choose this route in favour of a smelting option. However, for concentrates with elevated arsenic levels, oxidative pressure leaching offers distinct advantages, as smelter air emission standards and restrictions on concentrate importation have tightened. The current state of pressure leach technology allows for high copper extractions from arsenical copper concentrates, while producing an environmentally stable process residue, without atmospheric emissions of sulphur dioxide or arsenic. In its studies on pressure leaching of copper concentrates, Sherritt has shown that arsenical feed materials can be converted into environmentally stable residues, with excellent copper extractions. The results of recent batch and pilot plant test work are discussed, including the deportments of copper, arsenic and precious metals.

By Dan Wang, Yuanbo Zhang, Guihong Han, Guanghui Li, Tao Jiang, Yanfang Huang

"Hematite concentrates are characterized by bad high-temperature reactivity and poor balling index, which restrict their large-scale application in the production of oxidized pellets. An organic additive, namely MHA, was authorized and used as binder recently in China. Compared with bentonite, the effects of MHA on compressive strength of hematite pellets at various firing conditions were investigated in this study. Experimental results showed the compressive strengths of preheated pellets with different binders were increased with increasing the preheating temperature and time. The compressive strength of preheated pellets with MHA binder was lower than that of pellets with bentonite, which can be ascribed to the high porosity of pellets with MHA binder. However, the compressive strength of roasted pellets with MHA binder was higher than that of pellets with bentonite. The compressive strength of finished pellets balled with MHA binder 1.0 wt% could meet the operation requirements of grate-kiln process.IntroductionHematite concentrates are characterized by bad high-temperature reactivity and poor balling index, which can lead to the appearance of those problems with increasing the energy consumption, shortening the useful life of equipment, and finally increasing the operation cost of oxidized pellets plants [1-2]. Some investigations have been conducted based on improving the pelletizing technique of hematite concentrates, such as pretreatment of raw materials [3-7], optimization of ore proportioning [8], addition of solid fuels [9-16], and so on. Employing high pressure grinding roller for the treatment of hematite concentrates revealed that the mechanical strength of wet green pellets could be improved. However, the mechanical strength of fired pellets was not improved obviously [7]. Huang, et al., pointed out that the preheating and roasting temperature may be decreased and the compressive strength of fired pellets could be increased by blending a certain proportion of magnetite concentrates with hematite [8]. Nevertheless, there are a variety of magnetite ores different in physical and chemical properties in China, resulting in the instability operation [17]."

Jan 1, 2012

By Jeffrey R. Taylor

The distribution of low concentrations of Cr, Mn, Rh, Co, Ni, Ag and Fe between copper matte and bullion phases has been measured at 1200oC. These results. together with values for nine other elements, have been used to develop a simple model to describe the distributions in terms of known thermodynamic properties?. The Temkin model for ionic melts was assumed to apply to the sulphide species in the Cu-S matte? phase and it is shown that the choice of sulphide species is particularly important for successful representation of the experimental .results?. In general, the lowest sulphlde (minimum sulphur :. metal ratio)? formed by the. metal is most suitable, although Ni, Co, Rh and Pd appear to associate with more sulphur in the melt than suggested by the? composition of their lowest sulphide. A correlation between the composition of the metal sulphide species formed in the ternary system and the? position of the minimum in the free energy of mixing curve in the metal-sulphur binary -system is? proposed.

Jan 1, 1983

By Sayan Sarkar

HAMR (Hydrogen Assisted Magnesiothermic Reduction) process is a promising alternative route of titanium production, which is convenient due to reduction at relatively lower temperatures below 750 °C and usage of cost-efficient TiO2 as the starting material. A crucial step involved in this process requires the Mg reduction of TiO2 subjected to H2 atmosphere which produces porous TiH2 along with residual magnesium impurities. Before the final heat treatment and deoxygenation steps for consolidation of the Ti powder, leaching plays a significant role in the removal of Mg impurities. In this report, we present a systematic study on the role of acid concentration (HCl), temperature and the kinetics of MgO dissolution. In addition, we also report the controlling mechanism during kinetics of MgO dissolution in acid. This parametric study will provide a platform to ensure very low Mg content that meets with ASTM standards during production of Ti in the HAMR process.

By Lanre Oshinowo

Computational Fluid Dynamics (CFD) is used in conjunction with process modelling at HATCH to achieve a superior level of confidence in the process design of hydrometallurgical process plants. The use of these tools to evaluate designs through virtual prototyping reduces the risks associated with making design decisions. This paper highlights the development of a co-simulation strategy at Hatch for the seamless integration of process modeling software addressing different scales (process time and space): flowsheet level models and .equipment level models. With co-simulation, the process design engineers can improve design accuracy, troubleshoot and optimize performance and influence decisions impacting equipment operation by representing specific unit operations in the flowsheet model software with detailed CFD models. Specifically, this paper will focus on the co-simulation of a Ni/Co high-pressure acid leach (HPAL) process including heaters/heat exchangers and flash system, autoclave and quench/scrubber system. The knowledge developed can be transferable to other processes.

Jan 1, 2004

By T. Feldmann

Despite the ubiquity of applications for germanium, there is a lack of practically useful solubility data in acidic solutions. Previous studies were done at ambient temperature and only for commonly used acids (H2SO4, HCl). Hence, an investigation of the solubility of GeO2 in different acids was undertaken. Several inorganic and organic acids were studied in the concentration range of 1–11 mol/L and at 23, 40, and 60 °C. In the case of H2SO4 and HCl previous data was confirmed. Lower acidity resulted in a higher solubility for Ge at all tested temperatures. Tests done at 40 and 60 °C and low to moderate acidity levels, gave slightly increased solubility values at higher temperatures compared to 23 °C. This wasn’t the case at higher acidity levels, i.e., the solubility curves at different temperatures converge at high acidity. Lastly, a relationship of water activity and GeO2 solubility in different acid media was established.

By Jiang Feng, Zhang Libo, Peng Jinhui, Guo Zhanyong, Ju Shaohua, Lei Ting

The basics of microwave drying process of CuCl residue were studied by comparing the dielectric property of the residue with different moisture contents. The dielectric properties were measured by microwave cavity perturbation method. The dielectric constant and dielectric loss factor of the CuCl residue have a linear correlation with the moisture content. With this relationship, we can realize on-line measurement of moisture content of the CuCl residue by dielectric properties. The microwave drying experiments with different thicknesses (1-5cm) of CuCl residue were carried out, and the heating curve of the materials under different microwave powers (250-450W) was made. From these parameters, an optimized operation parameter of microwave roasting technology, the thickness of CuCl residue filter cake to be microwave roasted should be 2cm , was deduced.

Jan 1, 2015

By Muhlis Nezihi Saridede, Burak Birol

"The scraps of high quality steels generally contain expensive alloying elements such as chromium, vanadium, nickel, etc. These scraps are melted in an induction or an electric arc furnace and refined in ESR (Electroslag Remelting) purification process. A significant amount of alloying elements are lost during these processes. In order to avoid these losses, scraps can be utilized directly in ESR by skipping the melting step. In this study, 316L stainless steel scraps were refined in ESR with selected synthetic slags. The products were analyzed by optic emission spectrometry and the effects of slag compositions on the alloying element losses were examined. According to the analysis of the scrap and the products, generally chromium, nickel and manganese losses were encountered. It was determined that the alloying element losses has no connection with electrical conductivity. The slag containing CaF2, Al2O3, and FeO gives the optimum Cr and Ni losses.IntroductionElectroslag remelting (ESR), which is the consumable electrode refining process, finds a wide range of utilization for the production of high quality, low inclusion alloys. This process is based on melting a consumable electrode under a molten synthetic slag containing CaF2, Al2O3, CaO etc. The synthetic slag provides the chemical refining and insulation of molten metal from air which leads to a higher purity and an inclusion-free product. [ 1,2] A schematic diagram of ESR system is shown in Figure 1."

Jan 1, 2011

By Marko Suput

Titanium is a high-strength, low-density metal nearly immune to corrosion, but limited in use by its high price. The high price is due to the cost of smelting and processing the ore. The research on titanium production using the Solid Oxide Membrane (SOM) process aims to consolidate most of the processing steps required for conventional titanium production into a single step making it an energy-efficient and cost-effective method for producing CP billet and ingot and possibly also powders used to make titanium alloys. In the SOM process experiment, a steel crucible contains MgF2-CaF2-TiO2 flux; an inert metal/carbon rod serves as the cathode; an oxygen-ion-conducting yttrium-stabilized-zirconia (YSZ) membrane in the form of a one-end-closed tube contains either a liquid metal that acts as the anode or liquid MgF2-CaF2 ionic flux that connects the YSZ membrane to an anode. During electrolysis, when the voltage between anode and cathode is higher than the reduction potential of titanium oxide, titanium ions are reduced at the cathode and the oxygen ions pass through the YSZ membrane and are oxidized at the anode. The oxygen ions are oxidized at the anode by a reducing agent, hydrogen gas or carbon, forming steam or CO(g), respectively. To date, a suitable MgF2-CaF2-TiO2 flux has been selected and the operating temperature for the SOM process has been determined. Several electrolysis experiments have been performed. As expected, lower valence deposits of titanium oxides have been witnessed at the cathode prior to depositing pure titanium. Continuing work will aim to extend the electrolysis time in order to pass enough charge to produce a significant amount (100 g) of titanium at the cathode.

Jan 1, 2006

Acid mine drainage containing heavy metal ions is a large environmental problem facing the mining and mineral processing industry. The femte coprecipitation is a novel technique for removing heavy metal ions from waste water, recently applied to acid mine drainage. The fenite precipitation is usually performed at high temperature and therefore if applied in conventional manner, it becomes uneconomical to treat large quantities of acid mine drainage. In this paper the ferrite precipitation at ambient temperature-is &died. The possible mechanism of ferrite formation is discussed Experimental results from Noranda Tailing and Berkeley Pit water treated by this process are presented.

Jan 1, 1994

By R. M. G. S. Berezowsky

Treatment of Hudson Bay Mining and Smelting Co. Ltd. (HBM&S) zinc concentrate in the Sherritt zinc pressure leach process produces a residue containing elemental sulphur, residual sulphides, precipitated iron species, si1ver and gold. Flotation of the residue recovers most of the elemental sulphur and residual sulphides to the concentrate, leaving iron oxides and bask sulphates in the tailings. The tailings also contain most of the sflver and some gold. Direct cyantde leaching of the oxide tailings (220 g/t Ag, 1.4 g/t Au) was capable of leaching most of the gold, but only a minor portion of the silver. This paper reports testwork, conducted by Sherritt on behalf of HBM&S, to define a process for a high recovery of the precious metals from the oxide tailings. A si1ver enhancement treatment, consisting basically of digestion of the residue with lime at 90°C to render the silver amenable to enhanced recovery by subsequent cyanidation, was selected as the most promising approach. Batch silver enhancement and cyanidation tests showed that treatment of the oxide residue with 80 kg/t CaO at 90°C for 1 to 2 h increased the silver extractability in subsequent cyanidation from <20% to 96%. A 96 h continuous miniplant test (1 kg/h solids feed rate), of a circuit including a silver enhancement treatment step followed by conventional cyanidation and carbon in pulp silver and gold recovery, confirmed metal recoveries to the carbon of 90% Au and 96% Ag. Reagent consumption rates were 1ess than 100 ?kg/t CaO and 5 kg/t NaCN.

Jan 1, 1990