Search Documents

By Yigit E, Royston D, Winborne DA

Semi-bulk concentrates of 45% zinc at 80% recovery have been produced from the McArthur River mineral deposit. Selective leaching of these concentrates to recover lead and a commercial grade zinc concentrate has the potential to increase significantly the recovery of zinc (as zinc concentrate) and lead (as lead metal) over conventional flotation methods producing lead and zinc concentrates.

Jan 1, 1986

The Rock Mass Rating (RMR) and Rock Mass Strength (RMS) classification systems for jointed rock masses are briefly reviewed, with particular reference to their use in slope stability studies. A correlation is provided between the results obtained from the two classifications and an equation is presented tentatively defining the RMR value for long-term stable slope angles. The validity of the equation is discussed in general terms in the context of slope stability problems commonly encountered in Western Australian open pit gold mines.

Jan 1, 1992

By Lawson F

Synthetic calaverite (Au Tez) has been prepared and its physical properties checked.Simple flotation tests indicate that the recovery of calaverite should be possible using n-butyl or sec-butyl xanthate collectors under approximately pi I neutral conditions with a copper sulphate activator.Roasting calaverite in air at moderate temperatures resulted in its decomposition with the formation of elemental gold and tellurium dioxide.In alkaline oxygenated cyanide solutions, both gold and tellurium tend to dissolve. At pHs less than 14, about 50 per cent of the tellurium remains as elemental tellurium; however in very strongly alkaline solutions, essentially all of the tellurium is converted to the soluble tellurite ion (TeOl-).However, even at high pHs, the solubility of gold in the cyanide solution is still low due almost certainly to passivation effects.

Jan 1, 1991

The relevant characteristic of the evolution of the Pacific continental margin of South America during the Mesozoic-Early Cenozoic has been tectonic segmentation. This has controlled suc-cesive episodes of sedimentary accumula-tion, extrusive and intrusive magmatism and deformation that ocurred at conver-vergent plate edges. During this inter-val, at least three main transverse boundaries played an important role conditioning the existence of paleo-segments of different longitudinal extent at various Periods. These probably correspond to deep-seated faults in the Huancabamba Deflection and at the Arica-Santa Cruz Line; the third boundary projects westward to the Chile Ridge. Tectonic activity appears to have been continous at the Huancabamba Deflection at least since the Triassic. The Arica-Santa Cruz Line was probably an active boundary during the Triassic and Cretaceous; the southernmost boundary may have started to be active at the end of the Jurassic. This tectonic activity has determined the subsidence - uplift and paleogeographic conditions of the paleosegments.

Jan 1, 1990

By N Takamatsu

The environments surrounding the iron and steel industry have changed greatly in recent years. Reported in this paper are the technologies adopted by the Japanese iron and steel industry to fititself to change in global steel demands, degradation of iron ore and coal, prolonging service life of the facilities and requirements of energy saving. In addition, innovative technologies for CO2 emission control in iron making processes are also discussed.

Jul 11, 2011

By Potter DJ, Firkin GR

The Imperial Smelting Furnace operated by Sulphide Corporation Pty. Limited at its Cockle Creek zinc-lead smelter was recently equipped with tuyeres angled at 25 degrees instead of the usual 10 degrees. This change was prompted by the results of model studies undertaken by tha Research Department of Imperial Smelting Processes Limited, at Avonmouth in the United Kingdom, and by the favourable results of operating trials on the Cockle Creek furnace using bent-tip tuyeres to simulate 25 degree inclination. The use of 25 degree angle tuyeres has made it possible to operate with lower zinc values in discard slag and has improved hearth stability over a wider range of sinter quality and composition.

Jan 1, 1981

By Adamiak Z. P, Nicol S. K

An exploratory study has been carried out on the applicability of pre-nucleated feed in pelletising operations. Measurements of the pellet quality parameters showed that iron ore pellets prepared in the above manner, generally meet the specifications required in international pellet traffic. Several potential economic advantages, such as reduced grinding power requirements, increased line productivity and shorter start-up periods, became apparent during the study.

Jan 1, 1974

The Ardlethan tin concentrator had dete riorated considerably in metallurgical per- formance, maintenance and plant availability. This problem was compounded by low tin prices and International Tin Council quotas. Mid- 1976 figures were: throughput - 1300 tonnes per day, availability 83% and metal recovery 537. Major problems existed throughout the circuit from crushing to tailings disposal and with morale, staffing, and housekeeping. With the lifting of the quotas in June 1976, management provided funds to implement a major rehabilitation programme and some fifteen major projects, at a cost of about $1.3 million have been completed to date. The change in performance has been dram- atic, and end of 1977 performance figures are: throughput - 1700 tonnes per day, availability 90% and metal recovery 65%.

Jan 1, 1978

By Garrigan J. S, Oakes I

Current operating practice in a plant commissioned some five years ago to treat ferritic zinc plant residue by the "Jarosite" process is described. Major problems overcome include obtaining reliable pH measurements at 100¦C, prevention of scale build up in spent electrolyte heaters, blinding of jarosite filter cloths and the deposition of gypsum in filter presses.

Jan 1, 1977

Alternatively are they a necessary evil'? Exploration geologists are a much higher profile group but then again the higher they are the bigger they Bill. At a mine site they are reluctantly being accepted as equals by mining engineers given the requirements of the `Code' in the reporting of Ore Reserves. How best can mining geologists service their customers? Are more revealing questions to be answered in who are their customers? In the past mining geologists lived isolated existences pouring over plans and sections, now with user-friendly software packages available and the use of LAN, mining geologists and mining engineers talk electronically - God forhid what the future might hying - they might even talk to accountants and metallurgists!

Jan 1, 1997

By Kuganathan K, Potvin Y

Enterprise Mine at Mount Isa is to expand ore production from the current 1.4 to 3.5 mtpa by mining the 3500 Orebody, from which production is scheduled to start in February 1998 making this the deepest underground mine in Australia with its lowest mining horizon at nearly 1.6 km below surface. The following fill requirements were defined for the 3500 Orebody during the feasibility study: 1. a minimum filling rate of 250 ma/h, 2. a curing time of 28 days, and 3. minimum free fill water. This paper mainly describes the investigation of high density and paste fills for the 3500 Orebody. The investigation covered all the key issues relating to fill option selection, including design criteria, material supply and demand assessment, drainage modelling, tailing dewatering method, mix design and a pump loop test. Results of the investigation indicate that both high density fill and paste fill are technically feasible. The investigation has led to the selection of a blended tailing paste for the 3500 Orebody as the paste option has significant advantages over high density fill in stope filling rates and fill reticulation. The blended tailing for paste fill is finer than Isa deslimed tailing but coarser than full plant tailing. The paste fill selected has minimum binder and tailing dewatering requirements while a relatively high filling rate is achieved.

Jan 1, 1998

By C M. Stewart, P Bowen

McArthur River Mine, in the Gulf Country of the Northern Territory, exploits one of worldÆs largest deposits of zinc, lead and silver. It was officially opened in September 1995, 40 years after its discovery in 1955. This paper describes the geological, engineering and metallurgical assessments which made up the feasibility study. It then relates how these study components compare with the first two years of operation. The challenges that had to be overcome before the McArthur River Mine became economically viable included the metallurgical problems associated with extremely fine grained ore and the development of an effective mining process.

Jan 1, 1998

Authority to Prospect 57P lies within the Surat Basin',' an eastern lobe of the Great Artesian.Basin, a major Mesozoic . downwarp that,had its inception'in Triassic time. The northern edge of the Mesozoic Surat Basin overlaps the southern extension of the Bowen Basin, a 'major structure that warped do*nWard in varying degrees from Permian time into Early'Triassic time: The axis of the Bowen Basin may be superimposed on the axis'of a still older structure, the Tasman Geosyncline, that probably originated in Ordovician time culminating in Late Carboniferous time.Within. or bordering the area the geologic record 'clearly marks.major differences in the stratigraphy and structure related, to"the successive evolution of these three distinct structural units. Three major phases of sedimentation have been recognised; one related to the development of the Tasman Geosyncline froi'n. Devonian to.Early Permian time (Horton group), one related to-the development of the Bowen Basin from Early Permian to_Early Tri= assic time (Bowen group), and one related to the development of the Great Artesian Basin from Triassic to Cretaceous time (Great Artesian . Group).

Jan 1, 1962

By Taylor R. N

Flow simulations have been performed on the flash-smelting burners currently used at KNS. This paper presents studies of the heat transfer between gas and particles at the burner exit. Gas and particle temperatures, velocity and concentration profiles of the two-phase flow are calculated by the mathematical model. The predicted gas temperatures have been favourably compared against values measured by thermocouples placed near the burners in the flash furnace. The predicted particle temperatures are also reasonable when compared with the measured temperatures.

Jan 1, 1992

By Waladan M, Elliot B, Rankin W. J

A survey was undertaken on the Kalgoorlie Nickel Smelter in which samples of slag and matte were taken along the length of the integrated flash smelting furnace and analysed to determine the variation of nickel and iron concentration. At the same time the oxygen potential of the slag and matte was measured using disposable tip solid-state oxygen probes. The results show that the oxygen potential of the slag is higher than that of the matte and that both decrease from the reaction shaft end to the slag tap hole end of the furnace. The slag and matte are not at equilibrium except towards the tap hole end. Reduction of nickel and magnetite from the slag occurs before the slag enters the slag-cleaning appendage by reaction with iron in the matte. Thermodynamic modelling and laboratory experiments showed that the equilibrium nickel and magnetite contents of the slag in the absence of a carbonaceous reducing agent are about 0.4 per cent and 7.5 per cent, respectively. A carbonaceous reductant is required to obtain a lower nickel content in the slag.

Jan 1, 1991

The Manto Verde copper mine (Atacama Region, Chile) is due to go into production in 1996. It will produce 40 000 tonne/year of copper cathode by heap leaching/SX-EW. Mineralogical studies were undertaken in conjunction with the metallurgical testwork program to characterise the ore and its response to leaching by dilute sulphuric acid. The leachable copper mineralogy is dominated by the oxide copper minerals: brochantite and malachite with minor chrysocolla and atacamite. The gangue minerals include abundant orthoclase, specularite, quartz and chlorite with minor muscovite and trace smectite clay, calcite and limonite. The study showed that complete or partial decomposition of calcite, chlorite, smectite and wad consumed acid and generated solution impurities (Ca2+, Fe2+, Mg2+, A13+, K+, Si4+ and Mn4+2+ ). Although these were manageable at Manto Verde, their uncontrolled build-up could have affected the operation in several ways: the degradation of heap penneability and fonnation of crud in the SX plant from the precipitation of gypsum, goethite, colloidal silica and jarosite; and the entrainment of contaminated pregnant leach solution in the SX organic resulting in the transfer of impurities to the electrolyte and subsequent effects on cathode quality and electrowinning efficiency. In conclusion, process mineralogy played an important role in understanding and managing potential mineral-related problems in the heap leaching and SX-EW recovery of Manto Verde ore.

Jan 1, 1994

The lignites of Otago and Southland offer a potentially viable future feedstock for electricity production and possible conversion to petrochemicals or liquid fuels. The deposits, when combined, represent New ZealandÆs largest energy inventory; equivalent to about 74 000 petajoules û or approximately 35 times current natural gas reserves. Too often dismissed as irrelevant to New ZealandÆs energy future because of adverse perceptions of the value of low rank coals, the strategic value of this resource is in fact huge.   Investigations of the lignites extend back over more than 50 years (LFTB various, CRL Energy Ltd). Whilst it is not the intention of this paper to review this work, these investigations have confirmed the suitability of the resource as a feedstock for thermochemical conversion. Current estimates of South Island lignite mining costs are NZ$1.0 - 3.0/GJ (Natusch 2005), making these resources amongst the most competitively-priced energy sources available world-wide.   This value, however, will only be captured if we as a country begin to envisage a world-scale, long-life, integrated and multi-faceted development sized to supply world markets for chemicals or fuels. Recent CAE studies (Hooper and Riddolls, 2005) have emphasised the vital importance of ensuring that any exploitation of this resource maximises their value to New Zealand. The question that thus must be applied is how might large-scale utilisation of the resource fit with New ZealandÆs primary energy supply, and its potential for the export of high-value commodities.   From the broader perspective of New ZealandÆs total energy supply equation we need to examine other supply options beyond just the generation of electricity. We face in this country a situation wherein almost all our liquid fuels feedstock has to be imported with projections for an increasing dependence on imported oil. In addition NZ has a natural gas reserves-to-production ratio of less than ten years, and dwindling supply from local production. Without further natural gas discoveries, New Zealand has only a window of approximately five years before we will need to commit to imported LNG or some other thermal fuels option.   In other words, New Zealand is facing an uncertain future unless we can restore energy inventories to cover an adequate strategic reserve capacity as well as enable long-term investment in alternative sources. Within this context the South Island lignite resources are thus deserving of more attention. The extent of the resource is well known, its suitability for conversion reasonably assessed, and its magnitude such that there is little doubt that lignite conversion could adequately meet NZÆs future energy needs for many years out.   This paper reviews coal gasification technology, its application to lignite and the possibilities for future development of the lignite resources. It is argued that the strategic imperative for this country is to secure the lignite resources as a primary energy source for this country well into the latter half of this century.

Jan 1, 2005

Since the early 1990s it has been evident that electricity demand has outstripped investment in generation and transmission. At the same time, concerns were being expressed about the risks associated with the run down of the Maui gas field. It is axiomatic that the necessary investments firstly require a stable and supportive regulatory and fiscal environment, and secondly that such investments have long lead times. A unwillingness by successive Governments to fund the necessary infrastructure, however, lead to the profound restructuring of the electricity with the ultimate objective of transferring the investment risk from Government to the private sector. Successive power crises since 1992 result from a failure to put in place a regulatory framework necessary to provide the environment to allow the private sector to make the needed investments within the necessary timeframe. The electricity sector has now stabilised to the extent that the regulatory risks associated with generation investment have been reduced. This does not mean that risk has been eliminated, however, and both economic and environmental issues will continue to constrain investment in some power proposals particularly those in the South Island and especially any South Island coal or gas thermal proposal. This is firstly because of several very simple economic issues:  1. while the South Island may have significant coal resources it lacks a significant electricity market; 2. except for a six to ten week period in a dry year, low cost hydro will price any large-scale South Island thermal out of the market which will restrict any large scale thermal station to a dry year and/or peaking load; 3. except for a six to ten week period in a dry year, export capacity on the HVDC link to the North Island is constrained to around 964 MWe (and 482 MWe from North to South in dry years); and 4. construction of any new thermal plant in the northern half of the North Island will price any South Island thermal station out of the market. There are also significant environmental issues associated with the establishment of a large scale thermally based power station in the South Island. Because the South Island lacks any large scale economically proven gas reserves, the environmental constraints considered are those associated with coal production. A coal mine dedicated to power generation will have significant on-site impacts associated, in particular those associated with disposal of opencast overburden and visual impacts. These will, however, be partially offset by the relative remoteness of such sites to population centres. What cannot be offset, however, is the off-site impacts, in particular, CO2, SOx and NOx emissions, water disposal and acid mine drainage.

Jan 1, 2003

By T Raynlyn, J J. Campbell, R J. Holmes, J R. Manuel, S P. Suthers, A Poliakov

Prediction of the downstream processing performance of iron ore needs detailed information on mineral composition, textural peculiarities, particle density, porosity, mineral liberation and association and mineral grain size. Optical image analysis and automated iron ore texture classification systems are a way of obtaining such information. Furthermore, this information can be used for predicting the output of specific processes and their combinations. Several examples of the application of such an approach to process performance studies for iron ore are discussed. These include the application of classification by ore texture to modelling and optimisation of hydrocyclone performance, the effect of including textural information in modelling of sinter properties, and combining textural information with an experimental study of stirring and ultrasonic treatment of haematitic-goethitic iron ore fines to understand the deportment of fines and the breakdown/deagglomeration of particles. In all cases, the availability of textural information is important and helps provide a better prediction of process performance and/or understanding of the unit process.

Jan 1, 2008

By Smith R. N

The Olympic Dam copper-uranium-gold-silver deposit is located approximately 520km north-northwest of Adelaide, South Australia. The deposit was discovered in 1975 by the Exploration Division of Western Mining Corporation (WMC). A joint venture, to facilitate development of the deposit was formed in mid 1979 between WMC (51%) and the British Petroleum Group (BP) (49%).

Jan 1, 1990