Search Documents

By Cy Jordan, Ben Burdett, Adrian Dance, Jack Rainey

"In 1997, EIMCO Minerals installed a knowledge-based control system on one of the five primary grinding lines at Highland Valley Copper. The objective of the system is to maximise throughput without affecting circuit product size or flotation recovery. The system was commissioned in October 1997 on a SAG mill/ball mill circuit following a plant audit and upgrade of the control instrumentation.The system monitors and controls the SAG mill power, bearing pressure and recycle load by manipulating the solids feedrate, water addition and mill speed. The two ball mill and cyclone circuits are controlled through water addition at various points in the circuit as well as the number of operating cyclones.An on-line particle size analyser is used to measure the cyclone overflow quality. Models of the SAG mill charge level and overflow product size are also incorporated. A method of predicting the SAG mill power response to feedrate changes is used to lessen the effect of dead time for improved mill power control. In the future, inferred measurements of SAG feed particle size and hardness will allow changes in ore behaviour to be predicted and compensated for by the system.This paper describes the development of the project -from installation and commissioning to modifications and refinement -along with prospects for the future.BackgroundIn early 1997, EIMCO Minerals was contracted by Highland Valley Copper to install a knowledge-based or expert system control strategy on one of the five grinding lines in the mill. This was to become the start of the Advanced Control Project at Highland Valley Copper (HVC). This paper will review the progress of the Project as well as discuss the prospects for the future.Following a preliminary engineering study (or plant audit) by EIMCO in 1996, it was decided to implement an advanced control system in order to improve plant operations and increase productivity. The study suggested that such a system had a pay-back period of a few months through increased throughput without loss in flotation recovery. Highland Valley already had successfully applied higher level control through their Elsag Bailey distributed control system (DCS) and this was the next stage in process optimisation."

Jan 1, 1998

By R. G. L. McCready, R. O. van Everdingen, M. Kalin, R. van Everdingen

"This paper is based on data generated between October, 1986 and October, 1989, during the implementation of an Ecological Engineering close-out for a zinc mine in Northern Ontario, where 690000 tonnes of tailings contain 41.1% pyrite and 4.1% pyrrhotite. The objective was to determine rates of sulphide oxidation and iron precipitation in the tailings. Those rates are relevant for the assessment of the long-term effectiveness of biological systems employed in the removal of heavy metals from contaminated drainage issuing from tailings.Data were collected on the topography and stratigraphy of the tailings basin, subsurface temperatures and groundwater levels, and chemical analyses were made of water samples collected from a number of piezometers. The thickness of unsaturated tailings varied widely between individual piezometer locations; annual maxima ranged from 0.67 m to 3.55 m, and annual minima from 0 to 2.68 m. Sulphate concentrations ranged from 36 mg/L to 20180 mg/L; iron concentrations from 0.36 mg/L to 9938 mg/L; and zinc concentrations from 0.33 mg/L to 1123 mg/L.The geochemistry of the piezometer samples suggests that some of the initial Fe content, resulting from metal sulphide oxidation, is subsequently precipitated in the tailings pile and, possibly, in the underlying unconsolidated sediments, probably in the form of iron-hydroxide and Na-jarosite. Other metals such as Zn may be co-precipitated with Fe. The discharge of a portion of these metals to the environment would be delayed by this process. Some of the initial sulphate may also be lost from solution, probably by precipitation of gypsum; approximate saturation degrees for gypsum ranged from -3.27 to +0.47. The precipitated minerals will somewhat decrease the porosity and permeability of the tailings.Sulphide-oxidation rates, calculated using the analytical results and the estimated amount of annual recharge at the tailings site, average 0.0057 mol/kg/yr. Calculated iron-precipitation rates average 0.000386 mol/kg/yr. It is concluded that the characteristics of seepage from mining wastes may change with time, reflecting the solubilization of precipitated secondary minerals."

Jan 1, 1992

By W. H. MacLean

The Matagami district lies directly west of Chibougamau on the north side of the Abi tibi greens tone belt. Ores at Matagami are volcanogenic massive sulphides and occur in the dominantly rhyolitic Watson Lake group surrounding the Bell River Igneous Complex. Rhyolites and basalts of this group, and basalts of the overlying Wabassee group in the central part of the district, are tholeiitic; calc-alkaline Wabassee rocks occur in the western part. Massive sulphides occur associated with rhyolite domes that can be delineated by paleotopographic and isopach mapping. They are mainly distal deposits that formed over an extended period of time while several volcanic units were being deposited,

Jan 1, 1984

By R. A. Brown

RIGHT NOW the Canadian oil business is suffering from growing pains brought on by developments outside our borders. I would like, therefore, to place our industry in perspective for you in two ways. I would like first to describe it briefly and let you see it in relation to the world oil industry. Then I would like to bring it back and place it into perspective against a strictly Canadian background. Naturally, in such a discussion, it is necessary to use a certain amount of statistical material. I'll endeavour, however, to keep it to a minimum. Eleven years ago, before the discovery of Leduc, Alberta could boast of having 21,000,000 barrels of crude oil reserves. Five years ago we had 1,810,000,000 barrels. At year end, 1957, our remaining recoverable reserves totalled more than 3,000,000,000 barrels. In 1957, our potential production in Alberta reached an all-time high of 756,000 barrels a day. Unfortunately, our actual average daily production dropped from 393,000 barrels per day in 1956 to 376,000 barrels per day in 1957. And in 1958, to date, it has dropped sharply to around 300,000 barrels per day.

Jan 1, 1958

By M. D. Scott

"Highland Valley Copper recently installed a semi-mobile in-pit crushing and conveyor system designed to feed both the Bethlehem and Lornex concentrators with a feed averaging 120000 tonnes per day. The system installed with a rated capacity of 12000 tonnes per hour is the highest capacity hard rock semi-mobile crushing and conveying system currently in existence.The system is designed in a manner that the crushers can be moved easily as the pit is developed in depth with conveyors extending deeper into the pit, and conveyors being moved radially from a surge pile located at the rim of the ultimate pit as the pit increases in size laterally.The system consists of two 6000 tph, 60 by 89 Krupp semimobile crushers feeding two moveable 4500 hp, 60 in. conveyors, 1.25 km long feeding a 7500 tonne live storage surge pile. Two 96 in. belt feeders installed in reclaim tunnels under the pile feed two parallel 4500 hp, 60 in. conveyors, 1.25 km long on a 12 per cent uphill grade to the two existing Lornex plant feed conveyors. A third 96 in. belt feeder, under the pile, feeds a 60 in. conveyor, loading trucks hauling crushed ore to the Bethlehem mill.A description will be given: (1) of the system's design features in which climatic extremes, operating, and maintenance characteristics were of primary importance; (2) of the way the system was constructed from components purchased internationally on an extremely tight construction schedule; and (3) of the way the system has operated during the first few months in operation during which time it demonstrated that it has met various design criteria."

Jan 1, 1988

By B. J. Morash

"The six mineable coal seams at Quintette Coal Limited (QCL) vary in thickness from 0.75 m to 9.5 m and include waste partings varying from 0.2 m to 4 m thick. They are highly faulted and folded in some areas and dip angles range from horizontal to 90 degrees. Due to this variation in thickness and orientation of the seams, several different mining methods are used to economically recover the coal. The key to QCL's success depends on the timely collection of detailed geology data and on mine planning which allows selection of the best method of mining to achieve maximum coal recovery with minimum dilution and cost. This paper will describe the various methods of mining employed and the criteria used to select them. IntroductionThe unique challenge in mining at Quintette Coal Limited (QCL) is to extract large quantities of coal and waste, from a complex orebody, with constricted areas for mining and waste disposal. This challenge dictates the mining of as many as four 10 m benches per year, through complicated coal structures, from three separate open pits with a total of 19coal seams. This total is made up of 5 seams at Mesa, 8 seams at Wolverine and 6 seams at Shikano (Fig. 1).Computer-aided mine planning and scheduling is carried out on a routine basis to ensure the prudent selection of methods of mining, to produce plans which ensure delivery of appropriately blended raw coals to the plant, and to coordinate disposal of large quantities of waste.Several methods of mining are applied simultaneously, and as a result coal and waste are released at different rates from twelve to fifteen mining faces. In order to ensure uninterrupted flow of material from excavators and to utilize the truck fleet effectively, a computerized dispatch system is employed.GeologyGenerally, geological conditions can be related to structural (faults and dip angle) and/or stratigraphic (coal seam and interseam waste thickness) sources"

Jan 1, 1988

By C. J. Sullivan

Many metalliferous ?provinces are co-extensive with particular groups of sedimentary, volcanic, or :basic plutonic rocks. Deposits may be truly syngenetic (Rand, Rhodesia-Katanga, Mans-field, Blind River, White Pine); re-. concentrated by circulating waters (Colorado Plateau, Red Bed Coppers) ; or re-concentrated thermally during metamorphism and granitization (most uranium and lead-zinc provinces ?and some copper and gold provinces). Basalts may yield important cop-per provinces when folded and re-heated. Granitization of basalts which have not reached the chlorite-carbon-ate phase of metamorphism may produce copper provinces. If they reach ?the chlorite-carbonate stage, granitization may result in a gold province. Copper and copper-nickel provinces may result if gabbros are granitized, and a ?similar alteration of per-idotite may result in asbestos or nickel ores. Many similar associations are known. Granite is not a source of ore, but a result of heat. A classification of ?ore with respect to source rocks is of greater prospecting value than are classifications based on magmatic differentiation and hydrother-mal solution theories. Volcanic centres are important ore foci because the thermally unstable metallic sulphides may be concentrated here by a distillation process. The ores found in the hot spring deposits, viz., mercury, mercury sulphide, sulphur, and the compounds of ?antimony and arsenic, are not those which are soluble in water at low temperature (epithermal sub-division of hydrothermal class), abrut those which are unstable thermally at comparatively low temperatures . Water is one of the most common thermally unstable minerals, and generally accompanies the thermally activated ore-forming sulphides.

Jan 1, 1957

By P. C. Patnaik

Performance of industrial gas turbine engines in terms of power output, reduced cooling and efficiency have been continuously increasing in parallel with aero gas turbines due to the advances made in the development of new materials, protective thermal barrier coatings (TBCs) and the advanced diagnostics to monitor service induced problems such as hot corrosion, thermal and thermo-mechanical fatigue and other operational issues, Environmental attack (hot corrosion or high temperature oxidation) is a common degradation mode in the hot section of the gas turbine, Hot corrosion occurs when Na or K bearing compounds in the environment or in the fuel combine with other contaminants such as S and Pb or V to form corrosive sulphates or vanadates thus attacking the protective oxide on the turbine airfoil, These problems pose far more threat to new turbine engine materials such as directional solidified, single crystals and ceramic matrix composites (CMCs). The CMCs due to their increased temperature capability, when used in the combustion chamber, are likely to reduce the peak temperatures attained during combustion and therefore provide the benefits of reduced emissions of oxides of C and N, These issues will be reviewed critically and their impact will be assessed on gas turbine lives. With respect to alternate fuels, past experience has shown that utilization of residual oils and coal derived fuels in gas turbines have resulted in complex deposition and corrosion processes, In recent years biomass derived alternate fuels have been used either through a gasification cycle or through direct firing of the biomass derived liquid fuel with a view to reduce Green House Gases (GHGs) and improve the climatic conditions. In both cases, the resulting high temperature corrosion processes (in the presence of alkaloids in the fuel) are also very complex, leading to premature removal of hot section components, Technology solutions mitigating these fundamental problems will be reviewed and solutions presented.

Jan 1, 2005

By E. Krause, V. G. Papangelakis, S. Garg, R. Mahadevan, E. Edwards

"Bioleaching uses iron and sulfur-oxidizing bacteria to extract base metals from sulfide minerals. As bioleaching involves breaking the iron-sulfur bonds by ferric attack, the biologically mediated rate of iron oxidation is recognized to play a key role in influencing the overall kinetics. In this study, we investigate the catalytic ability of an indigenous AMD culture for oxidizing Fe(II) in solution. This culture was subsequently adapted on pyrrhotite tailings (0.6% Ni) by gradually increasing the solids loading. Results from this study show that such an adaptation reduces the initial lag phase in the biotic oxidation of Fe(II), thereby allowing for a higher Ni extraction when compared to experiments with an un-adapted culture at a similar solids loading. The use of adapted cultures also helps to reduce the residence time for bioleaching of Ni from pyrrhotite tailings. INTRODUCTIONAs the world demand for pure base metals grows; the mining industry is increasingly faced with the burden of processing lower grade ores and mining waste streams in order to recover the occluded metal VALUES ((Watling, 2006). The extractive metallurgy of nickel from sulfide minerals focuses on using a combination of mineral processing, pyrometallurgical (smelting) and hydrometallurgical techniques to extract Ni from its ore bodies.Pyrrhotite (Fe1-xS) is commonly found in association with pentlandite and chalcopyrite in sulfidic Ni ores, such as those found in Sudbury, Ontario, and in Russia, e.g. Norilsk. The vast majority of this pyrrhotite needs to be removed using mineral processing techniques, in order to minimize the Fe and S contents of the concentrates that proceed on to smelting. If all pyrrhotite were left in the concentrate, much more slag and SO2 would be produced, and the smelter throughput would be limited. Beneficiation of Ni sulfide ores leads to the rejection of unwanted constituents as mining wastes, which may still contain extractable amounts of Ni (Edgar Peek et al., 2010)."

Jan 1, 2012

This paper states how alloy and welding advances have made possible the rapid development of the use of aluminum in the construction of equipment for earth moving and off -highway rock hauling. The main details are given regarding the construction and field testing carried out on an aluminum prototype body. The test results of strain gauge readings are analysed, and a description is given of how these have been applied in subsequent designs. The increase in the number of aluminum units put into the various types of service in Canada, as well as the problems encountered, is described, and the experience gained from five years of field service is discussed in some detail. An assessment is also made of the durability of the e units. The economics of using aluminum, together with the current development position, are reviewed, and predictions are made for considerable future increases in the use of aluminum units in open-pit and off-highway operations.

Jan 1, 1964

By Donald P. MacKinnon

"This paper is a commentary on selected trends within the transportation industry.In general, innovations are taking place within all modes of transport (road, rail and water) serving the industrial minerals industry which will affect future distribution patterns, methods and costs. Significant technical innovations in the transportation of solids by• pipeline will also appear, perhaps in the near future, permitting the transport of specific commodities, including some industrial minerals. However, the timing and magnitude of the commercial exploitation of solids pipelines are heavily dictated by marketing factors and distribution system logistics, as well as by the innovations likely to take place within competitive modes of transport. Competitive technological developments will include increased ship capacities, improved bulk-handling facilities, larger and specialized bulk-handling rail equipment, unit trains, containerization, larger ""off-highway"" vehicles and greater inter-modal integration. Equally significant are some ""soft-ware"" techniques such as the growing interest in total distribution cost concepts. However, the impact of the developments will not be spread uniformly over all Canadian industrial minerals."

Jan 1, 1967

By D. Yamada, T. Tanaka, N. Inouchi, J. Nakahigashi, H. Yoshimura, T. Nonishi

The use of cereal food materials as lubricants was investigated in an attempt to develop nonpolluting lubricants. Suspensions of wheat flour in water and other types of cereal food lubricants were prepared and their friction coefficients measured. The results indicate that a cereal food lubricant containing 30% lipids, 2% proteins, 60% carbohydrates and 0.6% calcium carbonates has the lowest friction coefficient for a sheet (cpTi-1). As example applications, the lubricant was tested with a forming press and a screw-fastening device. In both applications the cereal food lubricant performed relatively well in comparison to conventional lubricants and thereby has potential for practical applications.

Jan 1, 2006

By Grant L. Anderson, Richard C. Rice, Richard L. Jentgen

"Data for underground mine-hoist ropes determined in the Ontario Special Rope Tests were obtained, encoded and analyzed statistically. Prior 10 refined statistical analyses, these data were subjected la characterization studies and preliminary analyses to allow trends to emerge that could be used to guide and facilitate the refined analysis. The data were characterized by determining distribution s for a wide range of variables including remaining strength, service life in terms of lime and hoisting cycles, outer-wire torsion values, elongation during tensile testing, diameter reduction, location of strength loss and the strength lasses associated with corrosion rating and lubrication rating , This paper describes the more important relationships between remaining strength (or, conversely, strength loss) as the dependent variable and some of the principal independent variables mentioned above.IntroductionBoth productivity and safety in underground mines could be improved if mine-heist rope Iife and reliability could be predicted more accurately . As a result, hoist-rope failure processes and their effects on rope life and remaining strength need to be quantified and related in such a way that improved retirement criteria can be developed. This is true whether the failure is incipient or actual or whether the failure mode is by corrosion , wear, fatigue or a combination of these factors."

Jan 1, 1984

By George W. Bain

The area in Quebec immediately north of the Ottawa river is underlain by a large area of granite gneiss intruded in lit-par-lit fashion into Grenville sediments and low silica intrusives of the Buckingham Series. This complex of metamorphic rocks is intruded by a much later magma found, chiefly, as a very large stock about 20 miles in diameter and extending from Brownsburg to Grenville, and as dykes and small outliers at various places adjacent to its outer margin. 1A similar stock at Rigaud, Quebec, is situated south of the Ottawa river and has been described by O. E. Le Roy. The earliest representatives of the later magma are a series of granodiorite dykes characterized by abundant hornblende, along with primary magnetite and subordinate sulphides scattered as roundish grains through anorthoclase and aligoclase feldspars and subordinate quartz. The rock is found as narrow dykes and shows no prominent secondary structures, either in the field or in thin sections under the microscope.

Jan 1, 1926

By Yvon Trudeau, Deni Raymond

"The Orion gold mine, located 7 Ian northeast of the town of Malartic, Quebec, was discovered in mid-1985. Underground exploration was undertaken in 1986 leading to commercial production in 1988. The upper part of the orebody was exploited above the 125 m level and a total of 131 090 t at an average grade of 5.31 g/t gold were extracted.This paper describes the authors' current knowledge and interpretation of the geology, gold distribution, and structure of the Orion No.8 ore zone deposit. The deposit is an epigenetic lode gold occurrence somewhat unique in that both quartz-vein type and pyritic type of gold ore occur side-by-side. It is located within the Marban-Noriartic Deformation Corridor (MNDC) formed during a first deformation stage (D1) The MNDC is a well-defined regional structural feature in the Val d'Or - Malartic mining camp. Primary gold mineralization is associated with the D1 event and is represented by pyritized, silicified and brecciated basaltic lavas enclosed by ultramafic flow units. The ore zone is concordant with the MNDC. Felsic intrusions are spatially related with the ore zone, but their role in the genesis of the ore has yet to be dermed.A second deformation event (D2) resulted in local folding, a second schistosity (S2) and reverse faulting. Gold remobilization, the formation of the gold-bearing quartz breccia and the emplacement of the main quartz vein at the No. 8 zone deposit were associated with this event."

Jan 1, 1992

By Paul Guliov

Potash dominates the industrial mineral scene in Saskatchewan accounting for 44% of total provincial mineral production in 1981. More than 7 million tonnes of potash have been produced annualy in recent years; ten underground mines are presently (1983) active. Sodium sulphate and cement are also important mineral products. Construction aggregates, clay products, bentonite, salt, peat moss and sulphur complete the list of industrial mineral products.

Jan 1, 1984

By Robin Phinney

Certain statements in this presentation may constitute "forward-looking" statements which involve known and unknown risks, uncertainties and other factors which may cause the actual results, pe1formance or achievements of the Corporation, or industry results, to be materially different from any future results, performance or achievements expressed or implied by such forward-looking statements. When used in this presentation, such statements use such words as "may", "would", "could", "will", "intend", "expect", "believe", "plan", "anticipate", "estimate" and other similar terminology. These statements reflect the Corporation's current expectations regarding future events and operating performance and speak only as of the date of this presentation. Forward-looking statements involve significant risks and uncertainties, should not be read as guarantees of future performance or results, and will not necessa1ily be accurate indications of whether or not such results will be achieved. A number of factors could cause actual results to differ materially from the results discussed in the forward looking statements including, but not limited to, the factors discussed in the Corporation's annual information form filed on March 9, 2011. Actual results could differ materially from those currently anticipated due to a number of factors and risks. These include, but are not limited to, the failure to obtain necessary regulatory approvals, including environmental approval, the failure to secure full project financing, the failure to implement the recommendations set out in the Technical Report, the failure to raise financing to implement the recommendations in the Technical Report, risks associated with the mining industry in general (e.g., operational risks in development, exploration and production; delays or changes in plans with respect to exploration or development projects or capital expenditures; the uncertainty of estimates and projections relating to production, reserves and resources, costs and expenses; and health, safety and environmental risks), decrease in potash prices and exchange rate fluctuations. Although the forward-looking statements contained in this presentation are based upon what management of the Corporation believes are reasonable assumptions, the Corporation cannot assure shareholders that actual results will be consistent with these fonvard-looking statements. These fon\?ard-looking statements are made as of the date of this presentation and are expressly qualified in their entirety by this cautionary statement. Subject to applicable securities laws, the Corporation assumes no obligation to update or revise them to reflect new events or circumstances. This presentation is a market update based on the Corporation's public disclosure and does not form a part of any offer of securities, or constitute a solicitation of any offer to purchase or subscribe for securities. Any purchase of securities in the company should be made solely on the basis of information contained in the Corporation's public record which is available on www.sedar.com .

May 1, 2013

By Edgar Stansfield

Introduction First, I should define more closely the vague term 'recent work' that appears in the title of this paper. Following the period of depression that was an aftermath of the first Great War, the Research Council of, Alberta carried on for ten years without a Council and without a financial yote by the Legislature. In November, 1942, a new Council was formed, under the chairmanship of the Hon. N. E. Tanner, Minister of Lands and Mines, and a vote was granted by the Legislature early in 1943. By 'recent work', I mean work during the present regime. The Council is now going full steam ahead, or would be if it could get suitable technical assistance and required apparatus and materials. Lack of these has so far made unnecessary my responsibility for seeing that we do not exceed our estimates. The Annual Meeting of the Research Council will be held in November (1945), and at that meeting the programme of work for next year will be discussed. The present time is therefore the correct time for any of you who may have ideas as to work which might profitably be undertaken by the Council, to submit these ideas for consideration. I propose to discuss my subject under several headings, and to give enough of these to show that the Council has wide interests.

Jan 1, 1946

By O. D. Maurice

Feldspar mining in Canada came to an end during 1972 after many years of continuous activity. The deposits are not exhausted and the domestic demand for this product is expected to continue at about the same level as in recent years. The size of the industry does not justify the installation of expensive equipment in the mills, but it is believed that a modest profit could be made by a small operation using rudimentary methods of separation. Largescale and accurate mapping of the pegmatite dykes could help in planning mining operations for a better recovery of a uniform product.

Jan 1, 1973

By D. M. Ramsey

HIGH-INTENSITY magnetic separation as now practised in the commercial treatment of a large variety of industrial minerals is a com-paratively recent development, having had its practical beginning about ten years ago when it became necessary to devise more effective methods for the purification of the electric furnace abrasives and refractories-silicon carbide and fused aluminium oxide. The fundamentals of magnetic separation are, of course, very well under-stood; bur while very, very old in principle, the process has, in recent years, been developed to a point of far greater usefulness than heretofore. In fact, until the development of the high-intensity process,. magnetic separation was limited largely to the removal of tramp iron? with magnetic pulleys and the removal of the very highly magnetic portions of industrial minerals by means of horizontal conveyor-belt-type separators. All magnetic separation processes depend for their success on the fact that various materials are kinetically influenced to a greater or lesser degree by the force that we speak of as 'magnetism'. We have now come to regard 'magnetic separation' and 'high-intensity magnetic separation' as two different and distinct methods. However, both depend upon the reaction of a particle when placed in a magnetic field. The common types of magnetic separators quite generally operate on the principle that a magnetic particle can be lifted by a powerful magnetic force from a stream of material moving on a belt or other type of conveyor. The application of the force removing magnetic material by this scheme is directly opposed to the force of gravity and is, therefore, limited to sub-stances of a relatively high order of magnetic susceptibility, such as metallic iron and magnetite. Until a few years ago, one very important principle was almost entirely overlooked. Practically every substance is susceptible to some extent, at least, to magnetic attraction, and by the application of a magnetic force great enough, and properly applied, separations of materials heretofore considered 'non-magnetic' can be accomplished.

Jan 1, 1937