Search Documents

By T. G. Joseph, A. Chamanara

ABSTRACT: The chicken and egg scenario — where adverse truck motions cause ground deterioration and poor ground profiles cause adverse truck motions — is a downward deterioration spiral dominating our industry. If we remove one action, the reaction stops. A simple truck to excavator load data analysis and wireless communication system is outlined, which will provide visual assistance to the excavator operator in achieving improved load placement and balance in a truck body. This will reduce subsequent hauler duty cycle adverse motions and g levels that contribute to structural fatigue, higher tkph, reduced tire life, and ongoing maintenance of haul roads.

Jan 1, 2012

By G. H. Agnew

When water floods are initiated after gas-oil ratios have increased, the transition period from the start of injection until" the gas-oil ratios are returned to the solution gas-oil ratio may be important for either economic or technical reasons. The transition period is longest, and consequently most critical in water floods where injection is equal to withdrawals. This paper describes a theoretical basis for predicting the behavior of such a system and outlines a procedure for making the necessary calculations. The calculation procedure is illustrated for two actual cases: a line drive water flood and a five spot water flood. In each case there is a reasonable similarity between the actual and calculated performance.

Jan 1, 1960

By Marc Boyer

Modern civilization, modern industry, and modern standards of living, bring into, sharp relief the present-day essentiality of metals .and minerals, and the wide and diversified use which is made of them. Any attempt, therefore, to appraise the international situation today must take into consideration the metal and mineral resources of the world. If, as some believe, the world is divided into two distinct ideologies of political belief, one unalterably opposed to the other, so that armed conflict is unavoidable, then the question of national strength in mineral resources becomes of paramount importance. If, however, it is possible to avoid war by raising the standard of living in the underdeveloped ?areas of the world, thus ensuring all peoples everywhere against the dread spectres of starvation and disease, then the development of the world's mineral resources assumes even greater importance. Today it is difficult to realize that, prior to the industrial revolution in Great Britain, only a few of the metals and minerals now in common use entered into the everyday life of the people. !iron and steel, copper, lead, tin, and zinc, usually in .their unalloyed forms, along with the more common industrial minerals, were those most widely used, and then only in limited amount. With the advance of technology in metallurgy and in fabricating skills, the list of commercial metals and minerals has expanded until today they number more than eighty.

Jan 1, 1951

By C. T. Bischoff

Introduction Air conditioning is a term which has come into common use only during our generation. By definition, it means the positive and accurate control of temperature, humidity, movement, purity, and component constituents of the atmosphere within an enclosure. Claiming such results for Noranda's ventilation system, or for that of any other large mine, at present would be an idle boast. However, we are working toward that end with considerable success. Modern underground ventilation at Noranda dates back about six years. The later development of air conditioning is in its fourth season, but still in the experimental stage. Various ingenious methods have been devised to cool mines which, because of climatic or geological conditions or depth, are excessively warm. A few installations have been made to warm intake air during the winter months where this is necessary. However, the method currently in use at Noranda is unique in that it accomplishes both ends by one process. This method utilizes the freezing and melting of ice to equalize year-round temperatures. Mining Methods While a discussion of mining methods at Noranda is not proposed in this paper, a brief summary may be in order. The Horne mine of Noranda Mines, Limited, has been developed by six shafts, four of which are now active. The most recent, an internal shaft, extends to 6,000 feet below surface, but all of the ore mined to date has come from above the 3,000-foot level. Figure 1 shows a model of principal ore bodies. The area mined is relatively small in plan, considering its vertical extent and the tonnage per vertical foot. Most of the ore lies within an ellipse about 600 by 1,000 feet. While this has certain advantages, the mining of such massive orebodies has presented many problems.

Jan 1, 1947

By S. Konetschnik, Lux Degel, R. Degel, T. Haslinger

UrbanGold and its partners from Mettop and SMS group have developed a novel technology for the recovery of valuables from all non-ferrous metals’ fractions of WEEE (Waste Electrical and Electronic Equipment), with a special focus on low qualities which are commonly landfilled or incinerated. The technology is marketed under the brand name “UrbanGold Flex” to illustrate the high flexibility in respect of plant design and raw material portfolio, allowing also the processing of low grade material and materials with high caloric values. The process of the technology’s centrepiece, a modified and enhanced bath smelting furnace called “HENRI”, was investigated in numerous pyrometallurgical trials as basis for a scale-up towards a capacity of up to 100,000 tons of WEEE-concentrates per year. All relevant facility components have been evaluated in respect of references, fall-back options, as well as exit strategies (alternatives) to minimize risks when establishing a novel technology. A spin-off within the development is the “UrbanGold Compact” technology which can be seen as optimization of state-of-the-art smelters by using an optimized TBRC as primary processing unit. As an UrbanGold Compact plant will be the first industrial scale reference of UrbanGold’s technologies, it is also explained in the publication. As precious metals recovery is of major (economical) importance when recycling WEEE, major attention has been given to minimize the losses of these valuables. These measures, as well as a sophisticated way of utilizing waste heat as far as possible, result in interesting business cases with gross profits of up to 20% or even more. INTRODUCTION Over the past years, the demand of electrical and electronic equipment has increased dramatically with technological progress. Innovations on the technology of electronic devices led to a shorter usage and lifespan and thus boosted the generation of Waste Electrical and Electronic Equipment (WEEE). WEEE is one of the fastest growing waste streams, growing at 3 to 4% per year worldwide and is expected to reach more than 52 million tons per year by 2021. Currently, about 45 Mt of these wastes are estimated to arise worldwide, and the trend is rising (Baldé et al., 2017).

Jan 1, 2019

By G. Barr

"The Polymetallic Twin Metals Project deposits in Northern Minnesota are being developed by Twin Metals Minnesota. Amongst the flowsheet alternatives being examined at a prefeasibility study level is one involving flotation of a bulk concentrate followed by high temperature autoclaving of the concentrate using the PlatsolTM Process to solubilize all the valuable metals in the concentrate (Cu, Ni, Pt, Pd and Au). Autoclave operating conditions have been established in which recoveries of all the pay metals are in the 92 to 99% range, and the autoclave residence time has been reduced to an hour. The stability of the precious metals in solution after autoclaving has been assessed, as well as the impact of internally recycling process liquors to the feed to the autoclave.INTRODUCTIONPlatinum group metals (PGMs; platinum, palladium, rhodium, ruthenium, iridium and osmium) are traditionally recovered from their ores by production of a high-grade concentrate by flotation and/or gravity concentration followed by smelting of the concentrate. Concentrates are smelted to remove nonsulphide minerals and converted to remove iron and sulphur. The resulting high PGM grade matte is processed hydrometallurgically to leach the base metals, leaving a residue with a very high grade (20-40%) PGM concentrate for final refining to individual PGMs. Due to the complexity of this process and its high capital cost, this process can only be applied economically to high grade PGM ores. Lower grade PGM concentrates might be accepted as copper and nickel concentrates but may not yield attractive payment terms for the PGMs. The mineralized Duluth Gabbro region of Minnesota hosts several low grade base and PGM deposits and Twin Metals Minnesota is working to develop the Twin Metals Project deposits. Earlier studies at both pre-feasibility and feasibility level, by other mining companies, have failed to yield an economically viable project based on the traditional process. It is possible to produce a saleable copper concentrate from these ores, but economic recovery of nickel and PGMs into saleable concentrates proved elusive.In the late 1990’s and early 2000’s the Platsol™ process was developed at SGS in Lakefield, Ontario (at the time Lakefield Research Limited) for the NorthMet deposit (also within the Duluth Gabbro) owned by PolyMet Mining. The process developed was a high temperature chloride-assisted pressure oxidation process capable of dissolving simultaneously the base metals (Cu, Ni, Co, Zn), gold and the PGMs."

Jan 1, 2012

By J. Desroches, J. Burghardt, B. Lecampion, A. P. Bunger

"We present detailed comparisons between theoretical predictions and experiments for the initiation of radial hydraulic fractures transverse to a wellbore. Most of these experiments provide a measure of the time evolution of pressure, length, opening and flux entering the fracture during the test. We compare all these measurements simultaneously to our theoretical predictions, thoroughly testing hydraulic fracture initiation theory, which is shown to be predictive. These comparisons notably emphasize the difference between the initiation pressure (the wellbore pressure for which the fracture initiates) and the breakdown pressure (a misnomer which simply corresponds to the maximum pressure recorded during the test). INTRODUCTION In this paper, we will compare hydraulic fracturing laboratory experiments performed in different tight materials (PMMA, cement, shale) with the predictions from a numerical solution of the governing equations of hydraulic fracture mechanics (e.g. Geerstma & de Klerk, 1969; Detournay & Peirce, 2014). We focus on transverse radial hydraulic fractures initiating from a radial notch at the wellbore wall (see Figure 1). In particular, we will clarify the difference between the initiation pressure (the wellbore pressure at which the fracture initiates) and the breakdown pressure (a misnomer which simply corresponds to the maximum pressure recorded during a test, usually carried out at constant pump rate). This difference stems from the strong viscous effects at play during wellbore pressurization, fracture initiation and early propagation (i.e. fluid entrance in the newly created fracture). It has been observed on a number of experiments (e.g. Weijers, 1995; Zhao et al., 1996) and has a strong practical application, first because the maximum pressure is the most obvious value to report and second because that maximum value is necessary to specify injection systems."

Jan 1, 2015

By H. D. B. Wilson

THIS PAPER has resulted from a preliminary draft of a background paper prepared anonymously for the Science Council's Special Study of the Solid-Earth Sciences in Canada. The draft was circulated to eighty-four Canadian geologists; forty-eight of these responded with criticisms of the draft. All critical re-marks were considered carefully and most have been incorporated in the final paper in an attempt to balance the author's bias, although this bias undoubtedly still appears. Indications of support for a particular statement or section were also helpful, because many of these contradicted criticisms and enabled the author to judge the consensus. Thus, all criticism could not be incorporated because the referees did not agree. It is interesting that some remarks were con-sidered overstatements by some and too bland by others. The most perplexing critical comment was one which suggested a new author was needed, and went on to name the existing author as the most likely candidate.

Jan 1, 1970

By A. Desbiens, R. del Villar

"This two-part paper summarizes the design and implementation of a distributed PIbased control strategy installed at the B grinding circuit, at the Kidd Creek Division of Falconbridge Ltd. Part I details the design of the control strategy using a grinding circuit dynamic simulator (DYNAFRAG). The first step consisted of sampling campaigns and data processing to calibrate DYNAFRAG. Then, several control alternatives were designed and tested with the simulator. The main feature of these strategies is their ability to regulate or keep within an upper and lower limit five output variables (circulating load, rod mill density, cyclone feed and overflow densities and pump box level) with only three manipulated variables (rod mill water, pump box water and rod mill tonnage). By simulation on DYNAFRAG, it was possible to discriminate among several control structures. The preferred control strategy uses a saturation algorithm, which allows the adequate regulation of two measured variables with only one actuator. Controllers located in interacting loops are appropriately tuned, taking into account the existing process coupling. Part II will present the implementation of the selected control strategy.IntroductionSteady state simulators are used to predict the stationary state of a given process under specific operating conditions. Tradi - tionally, steady state simulation has been applied for process flowsheet design, for evaluating process modification benefits or for determining key operating parameters in process operation optimization. Dynamic simulators add a new dimension to process simulation since they allow the prediction of the process transient behaviour, resulting from the application of a different set of operating conditions and/or from natural disturbances or equipment failure. Dynamic simulators can also be used for the training of new operators or for the design of control strategies."

Jan 1, 1997

By C. H. Knight

"THE OBSERVATIONS that follow are confined to simple wet cyclones such as the cylindro-conical unit developed by the Dutch States Mines and marketed in America under the trademark 'Dorr-Clone'. Energy to do the work comes from the inlet velocity of the feed slurry, which is usually pumped' to the unit by a centrifugal pump.Such cyclones are simply classifiers of enormous capacity and depend for their separating effect on differences in rates of particle settlement. These particle settling rates, of course, vary with particle size, particle density, particle shape, pulp viscosity, and pulp density.The dilution of the overflow product affects both pulp viscosity and pulp density. In most operations, the temperature and the composition of the liquid -hence its viscosity --are fixed, but both pulp viscosity and pulp density can be changed by changing pulp dilution.Since the separating effect depends on differences in rates of particle setting, a perfect split with 100 per cent of the particles coarser than a given size in the underflow and 100 per cent of the finer sizes in the overflow is not possible. Just how far the separation departs from this perfection can be calculated rather exactly from the following principles, which also apply to mechanical classifiers. In removing or settling out of the overflow product all particles up to a specified size, some of the finer particles must settle out simultaneously."

Jan 1, 1955

By David G. Meadows

During the last decade Antofagasta Minerals? Los Pelambres Mine has dramatically increased its ore throughput following the fast initial phase ramp up through a series of planned incremental expansions. The original 85,000 mtpd, two SAG line plant was commissioned in 1999 and rapidly exceeded nameplate tonnage in only a few months. Following this, the inclusion of a pebble crushing circuit resulted in throughputs in excess of 114,000 mtpd and a recent, final third line SAG and ball mill addition have taken the plant to over 175,000 mtpd even with increasing ore hardness and changing ore feed characteristics. The progressive changes are described in this paper together with how the technical challenges have been met.

Jan 1, 2012

By Imane Benhamed, Jaouher Diouani, Laurent Cassayre, Florent Bourgeois, Carine Julcour-Lebigue, Université de Carthage

The attrition-leaching process aims at improving leaching performance when formation of passivation layers at the surface of leached particles is a severe limiting factor, as discussed recently by Julcour and coworkers (Julcour et al., 2015). This paper proposes a geochemistry-based modelling scheme for deriving the window of possible operating conditions for the attrition-leaching process to match the properties of the processed ore. The rationale is that the attrition-leaching process maintains the surface of reacting particles in an unpassivated state by continuous mechanical removal of surface leach layers, so that the process reactions can be modelled from thermodynamic equilibria throughout the duration of the process. The strength of the proposed modelling approach is that it bridges the gap between the properties of the ore and the process operating conditions. The present paper exemplifies the proposed process modelling route for derivation of the attrition-leaching process operating conditions in the context of the leaching of silicate ores, matching model predictions against controlled laboratory experiments. It is shown how thermodynamic modelling, when used in conjunction with a solid knowledge of the phases present in the system, can assist with deciding upon suitable process operating conditions. As an example, this firstprinciple modelling approach predicted that steel grinding medium would be converted into siderite (FeCO3) under a wide range of operating conditions, which led to questioning this initial choice of grinding medium for the attrition-leaching process under mineral carbonation conditions. It is emphasised that the same approach could be applied to ores of greater economic significance.

Jan 1, 2016

By George C. Coupland

"THE PRELIMINARY EVALUATION of the orebodies was computerized for tonnages and grades on a 20- by 20-ft grid. The evaluation was based on drill-core intersections over 40-ft vertical projections coinciding with the proposed bench intervals, taking the deviations of the drill holes into account. The computer print-outs gave an ore distribution and evaluation bench by bench and indicated the areas of varying mineralization. The two orebodies have a combined length of 2,200 ft. and a maximum width of 600 ft. They strike almost due north, dip about 85 degrees east and rake to the north. The computer print-outs were used to design an open pit with an over-all waste to ore ratio of 2.58:1. At the outset, the waste to ore ratio was 4:1. The pit is tear-drop shaped, with the narrow end to the south, and at the surface is 2,600 ft long by 1,800 ft wide. Ramps are 100 ft wide, with a 10% grade. The south ramp is left-handed, starts at the southeast and will continue to the bottom of the pit. A second ramp on the west and north walls runs from surface to join the south ramp at 7 bench. This ramp will handle the total pit production when part of the south ramp, from 4 bench to surface, is lost due to the underground operation. Over-all wall slopes are 53 degrees, and are laid out to avoid prominent protuberances which could relax and become unstable and potentially dangerous (Fig. 1) ."

Jan 1, 1974

By T. C. Rao, Deb Kanungo

"The results of tests carried out on a 3-in. hydrocyclone have shown the linear relationships that exist between: (1) the flow-rate of water in the feed to and the overflow product from the cyclone; (2) the flow-rate of solids in the feed to and the underflow product from the cyclone. The underflow size distribution of an operation has been found to be linear and its usefulness in evaluating particle distribution in the cyclone has been discussed. Effects of design and operating variables on the above relationships have been discussed. The performance of this 3-in. hydrocyclone has been compared with that of a 20-in. cyclone, the results for which are available in the literature."

Jan 1, 1973

By Emile D. L. Rienks

We have studied the interaction of NO with the quasi-hexagonally reconstructed Au(100) surface. Using variable temperature scanning tunneling microscopy we have observed formation of the unreconstructed phase of Au(100) after NO exposure. This NO adsorption induced phase transition is observed in a window of temperatures around 170 K. Under the same conditions, CO and O2 cannot drive the phase transition, suggesting weaker interaction. Thermal desorption spectroscopy experiments provide an estimate for the strength of NO chemisorption on Au(100) of 57 ± 4 kJ mol-1.

Oct 1, 2003

By N. Valkanov

This paper presents results of an investigation into the connection between minerals liberation management and flotation, responding to lead-zinc concentrator ?Erma reka?, in Bulgaria. Monitoring of a Zn flotation circuit was carried out. The causes for the high silica content in the final Zn concentrate were established. Quartz is present mainly as liberated particles (> 60?80 %) in the fine fractions of the products; therefore the selectivity of the flotation process is not effective. Two approaches were tested to reduce the quartz content of Zn concentrate: froth washing in Zn cleaner flotation and new gangue depressants in the Zn circuit. Experimental results from bench-scale flotation and industrial tests show that it is possibile to reduce the silica content of final Zn concentrate more than 2 times without the need for extensive regrinding. The depression of liberated quartz particles on all operations of Zn circuit using stage depressant addition is the right solution to produce high-grade Zn concentrate that meets the metallurgical requirements.

Aug 1, 2013

By W. Rostoker

Packing Experiments The porosity and most of the other physical properties of a coherent mass of any material built up by the packing together of discrete particles will obviously vary with, and be governed by, the manner of association of the particles. The relation of packing to powder metallurgy has been discussed in some detail by at least two authors. Packing Theory Theories of particle packing have been put forward by C. C. Furnas and A. E. R. Westman. Although their approach to the problem is not the same, their conclusions are similar. In the process of packing, they visualize the voids of a uniformly sized material becoming filled with particles of a smaller size, and the voids between these being filled in turn with still finer particles. Obviously, if this process is carried ad infinitum, the resultant mass will have the same density as the constituent particles. In practice, of course, such a density of packing is never attained. In addition, the premise is made that successive particle sizes must fit into the voids left by the immediately larger particles- an assumption requiring definite size gradations and also particle shapes. It remained, then, for theory to correlate relative diameter ratios, and proportions and numbers of sizes of particles, for requisite packed densities. Briefly, the following principles were postulated: (a) For an infinite diameter ratio between largest and smallest sizes, an infinite number of particle sizes in proper proportion is required to give natural density. (b) For a given diameter ratio, there is a maximum number of permissible particle sizes for maximum packed density (Furnas). (c) Provided the particle shape is spherical, or approximately so, the proportions o particle sizes can be calculated. (d) The ratios of successive diameters of particles are in geometric progression.

Jan 1, 1947

By A. K. Chetin, W. W. Fitkin

"The reservoirs of Mississippian Mi-dale beds and Frobisher beds found in the Weyburn field lie at the north-western termination of a broad productive belt extending 120 miles along the northeastern rim of the Williston basin. These carbonates, and inter-bedded evaporites, originated during cycles of marine transgression and regression, and were deposited as rock types characteristic of shoal, lagoon, and basinward shelf environments. The Frobisher-Alida Beds, which form a secondary reservoir to the main Midale Beds of producing zone are composed of oolit1c, fragmental-bioclastic, vugular limestone capped by an impervious dolomitic mudstone. Production is controlled by localized structural features resulting from de-positional build-up. Excellent reservoir conditions are accompanied by an active water drive. The Frobisher Evaporite, consisting of massive primary anhydrite with dolomitic veinlets, forms the floor seal for the Midale beds oil accumulation. A significant facies transition into an oolitic, bioclastic, vugular limestone characterizes this unit. Beyond the depositional margin of the evaporitic facies, marked increases in porosity and permeability of the en-tire reservoir are noted. Carbonate units overlying the areal extent of the Frobisher Evaporite exhibit a greater degree of metasomatism, dolomitization, and more abundant secondary anhydrite.Porous carbonates comprising the producing zone of the Midale beds are divided into an oolitic, fragmental bioclastic, vugular limestone, and an overlying granular marly lime-stone unit, capped, by the Midale Evaporite. Oil is accumulated in a stratigraphic trap bounded above and be-low by primary anhydrite and truncated by the post-Mississippian erosional surface. Mississippian strata dip basinward from this erosional surface in a broad homocline exhibiting only minor irregularities. Rapid lateral and vertical porosity and permeability variations are common. Localized, separated, porous lenticles contain interstitial water in areas where the Midale beds are underlain by the Frobisher Evaporite. The major portion of the field, however, is capable of water-free production. Bottom and edge waters are found in certain portions of the field. Productive limits are tentatively defined around most of the present field perimeter. A large area along foe southern edge of the field remains open to future development. Probable ultimate remaining recoverable crude oil reserves, as of September 30th, 1958, were estimated by Mc-Daniel Consultants Ltd. to be in excess of 330 million barrels."

Jan 1, 1959

By G. J. Kipouros, W. Judge

"The prevalent metal extraction processes for most reactive metals are fused salt electrolysis and metallothermic reduction. The feed material for both of these processes is the anhydrous chloride of the metal under consideration. Dehydration of the feed material is then a critical step in the production of most reactive metals and requires rigorous thermodynamic analysis. Thermodynamic data for most of the reactive metal chloride hydrates have not been measured. Improper dehydration of the metal chloride may lead to a prohibitive amount of hydroxychloride, oxychloride, and oxide. To prevent hydrolysis a certain pressure of hydrogen chloride is required. An estimation and prediction model is presented for the vapour pressures of reactive metal chloride hydrates in an attempt to deduce the conditions necessary for dehydration to proceed without hydrolysis. Thermodynamic data including heat capacities, standard entropies, and standard enthalpies are estimated/predicted for all conceivable intermediate hydrate compounds. Estimations are based on published data as well as trends proven in similar systems. The thermodynamic estimations and predictions are presented for the magnesium, neodymium, praseodymium, and dysprosium chloride hydrates. INTRODUCTIONThe high reactivity of metals such as the alkalis, alkaline earths, and lanthanides prevents their reduction by traditional pyro- or hydrometallurgy. In their elemental form, these metals are raw materials in the manufacture of intermediate products such as alloys and electronic components. Currently the only two viable metal production methods are fused salt electrolysis and metallothermic reduction. Various feed materials have been proposed for these processes. Using the chloride of the metal as a feed material offers advantages in separation and purity of the final product, as well as lower energy input. Chlorides, however, are hygroscopic and must be dehydrated before use. Improper dehydration will lead to a prohibitive amount of oxychloride which will lower efficiencies and contaminate the final product.Optimum conditions for proper dehydration of MgCl2•6H2O to produce pure MgCl2 without hydrolysis have been calculated from existent thermodynamic data and have been reported previously (Kipouros, 1987; 2001). Calculations were also performed for the case of production of pure anhydrous NdCl3 from NdCl3•6H2O (Roy, 1997)] and the mechanism of dehydration was elucidated. Some thermodynamic studies on the dehydration of chlorides of the rare earths have also been conducted (Sundstrom, 1997; Hong, 1997; Aschcroft, 1968; Haeseler, 1965; Ukraintseya, 1989)."

Jan 1, 2012

By Q. Li

"The precursor of In2O3 was prepared by hydrolysis precipitation/hydrothermal method using In(NO3)3 solution as the feed material and ammonium hydroxide as the neutralizing agent. The crystallinity, morphology and particle size of the products were characterized by SEM, XRD, BET and LPSA. The results showed that the hydrolysis product consists of an aggregate of cubic In(OH)3 particles with a short rod morphology. In the hydrothermal process, the structure, morphology and size of the particles changes through the mechanisms of Ostwald ripening and phase transition, respectively. When the hydrothermal temperature was less than 280 ?, the Ostwald ripening process took place, which changed the morphology of the particles from short rods to cuboids through dissolution-recrystallization. When the hydrothermal temperature was higher than 280 ?, the processes of Ostwald ripening and phase transition took place successively. Firstly, the morphology of the particles changed from short rods to cuboids through Ostwald ripening, and then, the phase transition from cubic In(OH)3 to orthorhombic InOOH occurred and the morphology of the particles changed from cuboids to polyhedron. INTRODUCTIONDue to its excellent electrical conductivity and optical transparency, indium tin oxide (ITO) film has been wildly used in flat-panel display, solar cell, antistatic coating and EMI shielding (Medvedovski et al., 2008). Indium oxide powder is one of the fundamental materials for preparing ITO film. Along with the development of ITO targets of both high density and large size, high quality indium oxide powders, such as single phase, nano-size, spherical morphology and mono-disperse, have been in high demand (Nakashima and Kumahara, 2002; Betz et al., 2006; Kim et al., 2007). The main preparation methods for indium tin oxide or indium oxide powders include chemical precipitation (Nam et al., 2001; Xu and Yu, 2007), melt atomizing-combustion (Chen et al., 2000) and spray pyrolysis (Ogi et al., 2009). Among them, chemical precipitation has been preferred, since it is simple, easy to control and suitable for industrial scale-up. In chemical precipitation method, indium oxide powders were prepared through the following steps: firstly, indium hydrate precursor was precipitated from an indium salt solution by neutralization using an alkali, such as ammonia; and then, indium oxide (In2O3) powders can be obtained from the precursor through calcination (Li et al., 2006), or solvothermal method (Lee and Choi, 2005), or hydrothermal processing/roasting (Xu et al., 2005; Chen and Li, 2007), respectively. However, the indium oxide powders obtained by direct roasting are polycrystalline, dispersable with a wide size distribution (Liao, 2006). The disadvantages of the solvothermal method are high cost, complicated after-treatment processes, as well as bad performances of the powders (Udawatte and Yanagisawa, 2000). Therefore, among three methods of obtaining indium oxide from the hydrolysis precursor, the hydrothermal process/roasting method is the most feasible to synthesize high quality In2O3 powder with uniform crystallinity and size (Kim et al., 2002; Zhu et al., 2004; Xu et al., 2005; Xu et al., 2005; Chen and Li, 2007; Seetha et al., 2009). However, current research on hydrothermal process-roasting method has been limited to the synthesis of a certain ITO or In2O3 powders under specific conditions. A systematic study on the phase transition, as well as the change of the morphology and size of the particles in the hydrothermal process is still missing. In this paper, the effects of hydrothermal processing on the mineralogy, morphology and size of products were investigated. The results showed that the evolution of crystal structure, morphology and size in the hydrothermal process was affected through the mechanisms of Ostwald ripening and phase transition successively. These results are novel and have guidance for improving the hydrothermal process for In2O3"

Jan 1, 2012