Search Documents

By Chappel R. A, Fishburn B. R

The Eastern Distributor Tunnels - the first major road tunnel project in Australia - are the preferred solution to traffic congestion problems, when compared with alternatives, in this inner urban environment. This is because of the reduced impact on residential housing, the improvement of the existing environment, less restrictions on future developments, and a reduction in noise and pollution. Developments leading to a tunnelled solution, traffic needs and reasons for route location are discussed. Criteria for design of tunnel alignments and geometry are described, including the restraints imposed by surface connections on profiles and grades resulting in low rock cover at tunnel portals. The main geotechnical restraints are a major weathered dyke at the shallow large span underground fork and the weathered Ashfield Shale capping the Hawkesbury Sandstone at a portal. Rock cuttability and excavation methods are discussed. Roadheader machines are the most suitable for the varying shallow arched cross sections required and the tunnel lengths involved but the use of blasting in special situations cannot be ruled out. Initial support for the major tunnel lengths will be provided by rock reinforcement in conjunction with shotcrete. Steel ribs are proposed in areas of low cover and weak ground. Final support will comprise an insitu concrete lining. Construction concepts and special tunnelling methods required at the shallow underground forks and tunnels are described.

Jan 1, 1987

By D F. Akhmetov, M Yasuike, M Komazaki, Y Kawa

Remote monitoring of geological situation at distant regions with complicated relief, including reliable detection of the rock falls and estimation of the scale of accidents, is of great importance for practical needs. In the paper, vibration data, caused by fall of sample objects and registered by cable sensors, are processed and analysed in order to construct some measure for the indirect evaluation of weight of fallen objects. Nonlinear models, which based on artificial neural networks (ANN), are proposed for the signal presentation. To improve and simplify the learning and classification abilities of the whole system, the aggregative learning method (ALM) is implemented. ALM features relatively low memory and computational resources needed for the procedure realisation, especially for data classification (recall) stage, in compare to conventional methods. The validity and efficiency of the proposed approach are tested through its application for rock fall detection and weight evaluation system using cable sensors and mobile communication network. Classification abilities of the proposed approach are shown useful for estimation of the fallen object weight. Characterised with high computational efficiency and simple decisionmaking procedure, the derived method can be useful for simple and reliable real-time monitoring system design.

Jan 1, 2003

In both surface and underground coal mines, the detection of geological structures ahead of workings is recognised as being fundamental to the efficient operation of the mine. Mining into zones of unexpected structures has a drastic effect on a mine's productivity. For the prediction of structures, geophysical methods can be applied from the air, from the ground surface, from boreholes and from underground workings. There are several improvements to report in the geophysical methods being developed for these purposes. These include developments in three-dimensional seismic reflection surveying, cross-hole seismic reflection methods and radar systems. The recent development of the radio imaging method for use in underground mine workings will complement existing in-seam seismic methods. Geophysical techniques for use in horizontal boreholes are also under development.

Jan 1, 1988

By Coxhead B. A, Brandt B. A

The geological exploration and evaluation of coal reserves involves the appraisal of very large amounts of data. Computers afford an ideal means of handling and manipulating the data, thereby avoiding the laborious and expensive method of manually compiling the logs in full descriptive language. The Minad system of computer storage and retrieval of geological and analytical data is particularly suited to the description of cores and cuttings from exploration drill-holes. The encoded data is arranged in a 120-column computer output sheet format; descriptive geological information in a 54-column geolog and analytical information in a 64-column assaylog. The acquired data is quantitative, uniform and relatively complete and can be selectively retrieved for processing by a wide range of specialized computer programs developed for the coal mining industry. Visual retrieval of data for manual processing is facilitated by the use of simple codes and logical word abbreviations.

Jan 1, 1977

By P Dean, M Elmouttie, Y Duan, X Luo

Slope instability is one of the major concerns in open pit mining operations. A significant collapse of the pit wall can result in injuries, damage to machinery and interruptions to production. A broadband microseismic monitoring technique has been developed for diagnosing the healthy condition of a target slope area. This technique has been successfully applied to an open pit mine in Chile. Our research has found that this microseismic monitoring technique can be used in open pits for tracking and locating a falling rock that is rolling on a slope, if a dedicated seismic sensor network has been established. In collaboration with other monitoring techniques (radar, laser scan, aerial photography), more accurate determination of rock rolling trajectories can be obtained. In this paper, an example of using the CSIRO microseismic monitoring technique at an open pit mine is presented. Results from an experiment where we used the microseismic technique for determination of the trajectory of a rockfalling on a slope are also presented.

Nov 8, 2021

By X Li, H Alehossein

The oscillating disc cutter (ODC) is an innovative technology for the continuous excavation of hard rock. This paper will discuss:the reasons for its development;its method of operation;current experimental results and mathematical modelling undertaken at the CMTE; andapplications in the mining and rock excavation industry.

Jan 1, 1999

By Hunefeld R

In the field of mining engineering, design and planning are complex tasks, which require the knowledge of various engineering disciplines. GRUBE (Graphisch-RechnerUnterstiitzter BergwerksEntwurf) is a modular databased program system, which offers computer aid for all mining departments using a 3D CAD software as the user interface. Despite the data quantity and complexity, specific and uniform working conditions have to be applied to the planning of technical equipment of a pit. With the application of 3D graphics, complex data stores and their interrelations become 'palpable' for the user by suitable visualisation. GRUBE-M forms the mechanical operations module of GRUBE, in which underground locations displayed as three-dimensional graphic models are `equipped' interactively. Planning alternatives can be created and compared quickly in terms of technical calculations and economical analysis.

Jan 1, 1995

The maintenance system for underground mobile equipment at Cobar Mines Pty. Ltd. has been modified from that originally planned as a result of experience gained in operating the equipment.Downtime due to breakdowns has been reduced by improvement of vehicle servicing and overhaul procedures.Frequency of breakdowns can be reduced by training operating and maintenance personnel to a high standard, ensuring adequate numbers of tradesmen and supervisors, good maintenance facilities and communications, a well designed mine layout, and a comprehensive stock of spare parts.A maintenance and downtime summary is compiled for each four-week operating period and this is useful in highlighting particular problems where corrective action must be taken.

Jan 1, 1969

By Cottrell EC

Remote sensing has been used for many years but until recently its application has been limited by the resolution of the data available. High resolution airborne multi-spectral scanner data (MSS) has proven suitable for a number of applications including environmental management and monitoring. A shallow water mapping research. project completed on the Gold Coast has shown that- remote sensing can be used as a cost effective tool for environmental management and Monitoring.

Jan 1, 1987

By R W. Wilson, A R. Branch

For hot mines, the use of mechanical refrigeration machines has become an essential feature of ventilation and cooling systems. Over the last 30 years, considerable effort has been made in developing refrigeration strategies and equipment to provide cooling that is cost-effective, reliable and energy efficient. In addition to these general design requirements it is necessary to take into account project specific factors such as long term mine cooling needs, operating strategy and installation time. This paper examines a number of actual mine cooling installations which illustrate how these features have influenced the design and installations. For many mines, it is known how the cooling requirements will increase as the mine develops, based on the life of mine plan. The design of the cooling installation must cater for both short- and long-term needs. The initial installation (to meet short-term requirements) must form an integral part of the ultimate cooling installation and as additional equipment and refrigeration machines are installed, it is necessary to ensure that the system remains cost-effective, reliable and energy efficient at all stages. For many mines, refrigeration machines are installed on surface and either operated near-continuously, or for the summer months only. Different maintenance strategies and policies with regard to standby equipment are highlighted for three mine installations. In spite of developments in cooling strategy, the cost of providing refrigeration remains expensive and many mines delay the introduction of refrigeration, as long as possible. When it is finally accepted that refrigeration is absolutely necessary, it is frequently necessary to æfast trackÆ the installation. To minimise site erection time and meet installation deadlines, factory pre-assembly and standardised modular equipment are widely used.

Jan 1, 2005

By Butler RD

The Singhbhum Copper Belt is an arcuate zone of verthrusting which extends over a strike length of about 180 kilometres, located in Eastern India, 150-300 kilometres west of Calcutta. The Belt is noted for its mineralisation, and both copper and uranium are currently being mined within it.

Jan 1, 1990

By E S. Souza, H Delboni Jr, M F. Calixto

This paper aims at presenting the results of laboratory, pilot plant and simulation studies for the design of the grinding circuit for the beneficiation of compact itabirites from the Conceitpo mine. Two alternatives were investigated, both utilising the current crushing circuit up to tertiary crushing. Under alternative #1, quaternary crushing was considered to produce the feed of the ball mill; under alternative #2, high pressure grinding rolls were selected to prepare the ball mill circuit feed. Pilot scale studies pointed towards the use of high pressure grinding rolls (HPGR). The circuit design was based on a throughput of 720 t/h, representing a nominal solids flow rate of 600 t/h, considering a design factor of 1.2, and P80 of 95 ¦m.

Jan 1, 2007

The behavior of a curved wall under earth pressures for a horseshoe shaped tunnel lining is considered to be closely related to the beha vior of a vertical beam with variable flexural sti-"ness on an elastic foundation. In stress analysis an approximate method which divides the axis of the tunnel lining into small finite lengths and replaces the integrals by summation is usually adopted. this method is extremely complicated and tedious. However the variations of the moment of inertia from point to point along the wall axis can be expressed by a power function inversely .eith the distance from the ll )ottom and the analytical method can still used. The equations for the calculation of deflection, rotation, bending moment, shearing urce, and soil reaction of the curved wall are derived in nondimensional forms in this paper.

Jan 1, 1987

Utah Development Company began prospecting for coking coal in 1961 and Blackwater Mine became a reality in June 1967. Exploratory and develop- ment drilling has been a continuing effort and reserves have been assessed at several stages. Some of the history of exploration and reserves assessment is given and practices in drilling, sampling and testing are described, particularly in regard to objectives of drilling and reserves estimation. The current methods for calculation of reserves are described and some comment is made regarding use of the data in mine blending control and plant operation including correla- tion of results.

Jan 1, 1979

Potential hlghwaJl mining reserves in Australia are large, but geotechnical and operating conditions are quite different from those where highwall mining has evolved in the USA. In order to achieve safe and effective resource recovery, equipment and procedures should be developed to penetrate 250 m in the Australian mining environment. This paper identifies key auributes to be incorporated in such machinery and methodology. These suggestions are intended to promote discussion on innovations to satisfy Australian requirements for highly productive, safe and environmentally acceptable techniques.

Jan 1, 1993

By Lawrence PR, Hoffman W

The dissolution of gold from various ore-bodies is discussed in terms of extraction rates and reagent consumptions during leaching. Gold dissolves slowly in cyanide but reagent consumptions are usually satisfactory. In almost all cases where excessive cyanide consumptions occur, similar high consumptions result with other lixiviants. Recovery of gold from cyanide solution is well established and comparatively simple technology.Gold dissolution in thiourea is faster than cyanide but significant consumptions of thiourea, due to both adsorption and oxidation, occur. Gold recovery from thiourea solutions is likely to be more difficult than from cyanide.Chlorination of gold is very fast in acidic conditions but excessive consumption of chlorine occurs for ores containing greater than 0.5% S. Reprecipitation of gold and handling of acidic chlorine solutions are both significant problems. The mechanism of gold reduction onto activated carbon creates difficulties in the carbon in pulp process for recovery of gold but means a simplification in the production of bullion from loaded carbon.

Jan 1, 1984

By P J. Harper

Maximising shareholder value is a widely stated strategic goal of many mining companies. Mining projects can be capital intensive and achieving good returns is essential to encourage future investment in the industry. Despite the widely accepted importance of shareholder value, the minerals industry is often accused of providing relatively poor returns when compared to other industries. There are many recent and well publicised examples of minerals companies that have failed to deliver value to their shareholders. There are numerous business improvement initiatives employed within the mining industry to assist mine operators improve performance. Some are more effective at creating value than others. Benchmarking is one technique that is commonly used to identify performance gaps and target and prioritise opportunities for improvement. However to be effective, Benchmarking must be used appropriately and result in actions that lead to measurable operational improvement. When conducting a Benchmarking project it is important to remember that the aim should be to improve value. For this to be achieved, the strategic goals must be incorporated into the process. This paper details a structured and comprehensive approach to conducting a successful Benchmarking project. Focusing on Benchmarking as a technique for measuring and improving operational performance in underground mines, the underlying drivers of best practice in underground mining are identified.

Jan 1, 2005

By Li N, Grimsey E. J

A technique has been developed for the fast measurement of the liquidus temperature of molten salt systems. The method employs a type K thermocouple embedded within the centre of a copper cylinder. The cylinder is immersed into the molten salt bath and the resultant heating curve is recorded using a PC-based data logging system. Upon immersion of the cylinder into the bath, a layer of salt freezes from the melt onto the surface. When this layer remelts during heating, the shape of the heating curve exhibits a change. The onset of this change can be detected by numerical differentiation of the heating curve, and the temperature at the onset represents an estimate of the liquidus of the melt. This work describes the technique and its application to the measurement of liquidus temperatures of MgC12 - NaCl and BaC12 - NaCl salt mixtures, in addition to a number of solidus temperatures.

Jan 1, 1996

Over the last 100 years in the Polish mining industry considerable work has been done to assess optimum slurry, develop flexible delivery systems and adjust the fill technology to a wide variety of mining and geological conditions. Sand or industrial mineral waste materials for the backfilling of underground voids are used to control ground movement and surface deformation. This paper discusses various criteria to be considered in the preparation of a fill, including slurry properties, mine infrastructure, mining geometry, placement methods and the purpose of the backfill. This paper presents laboratory and in situ test data on the influence of materials parameters on the slurry flow in a pipeline system, stiffness, permeability, binding time and strength of a backfill, on the distribution of mixture in underground voids or the penetration between roof fall materials.

Jan 1, 1998

Wire rope, when used for hoisting on a mine is the weak- est and most vulnerable unit in the most expensive'-group of installations or! the mine. With the introduction' of hoisting on the S1Koepe"' sheave, a new technique was-established. This innovation brought with it the certain- advantages which long had been recognised and which are being developed further. For many years, drum winders of many types had been the sole means by which ore had been hauled from mines. This type of winder, with its capacity for rope storage on the drum, permitted mine operating personnel to cut short lengths from

Jan 1, 1964