Search Documents

By Bernard Dallaire, Jean Cayouette, Sylvain Duchesne

"Louvicourt Mine's concentrator, located near Val d'Or, Quebec, treats an average of 4,300 tonnes of ore per day composed mainly of copper, zinc, gold and silver. An analysis of concentrator revenues and metallurgical losses shows a potential for additional gain, particularly in regards to precious metals (kustelite) where recovery is usually around 67 -70 %. The planning, installation and trial operational period of two Outokumpu SK-240 flash cells at the underflow of the primary cyclones took two years. The use of (( flash flotation )) technology has made it possible to exploit the favourable conditions at the underflow of the primary cyclones such as precious metal concentration and the presence of liberated coarse chalcopyrite. These conditions permit early flotation (fresh surfaces) of the kustelite and the liberated copper. Since the start-up of the flash cells, the metallurgical gains have turned out to be very positive with increases in metal recovery reflected in appreciable NSR gains. Also, significant savings in reagent consumption and a coarser copper concentrate have made it possible to reduce the drying cycle of the Larox filter presses since the cells were put into operation.BACKGROUNDLouvicourt Mine is operated by Aur Resources Inc. (30% ownership) on behalf of its partners Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corp. (25%). The mine is located in northwestern Quebec about 600 km north of Montreal and about 25 km east of the mining town of Val d'Or. The mine commenced commercial production in July 1994.The massive sulphide ore deposit lies at depths varying between 450 m and 900 m. Mining reserves (2% Cu equi. cut-off) as of Jan. Is', 2000 are estimated at 7.5 million tonnes of ore averaging 3.4% Cu, 1.8% Zn, 28.0 g/t Ag and 0.9 g/t Au. Delineated ore reserves permit the use of a mechanized transverse blasthole mining method. The extraction order is a typical 1.3.5 mining sequence. Primary and secondary stopes are 15 m wide, 15 to 70 m long (25 m long average) and 30 m high. Backfilling for pillar recovery and regional stability is required."

Jan 1, 2001

Geophysical Abstracts 1 - 86 were issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey; Abstracts 112 - 120 were issued in mimeographed form by the Bureau of Mines as Information Circulars 7256, 7257; 7267,`7273; 7285, 7292, 7303, 7310, and 7324. 1. GRAVITATIONAL METHODS 7933. Ansel, E. A Eine Untersuchung zum Problem der Isostasie (An Investigation Regarding the Problem of Isostasy). Gerlands Beitr. Geophys., Leipzig, vol. 59, 1942, pp. 16-26.

Jan 1, 1945

By Paul M. Tyler

In 1939, American industry got, off to a poor start, slowed down further during the first quarter, quickened after May, speeded up still more when war broke out again in Europe, and ended the year at a pace close to an all-time record. The average index of general business activity for the entire year (105) was well ahead of that for 1938 (86), failed to equal that of 1937 (110), and fell behind the average for 1929 (119) by a wide margin. (Federal Reserve Bank yearly indexes in parentheses).

Jan 1, 1940

In mining industries, materials loading and handling costs represent a significant component of the total (capital and operation) costs. A variety of methods have been applied in surface mine equipment selection in order to select the suitable loading and haulage system with the lowest total cost. The optimal size and number of equipment calculation are very important task for mining engineering because loading and haulage equipment are major proportion of open pit mining cost. Capital and operating cost are considered in objective function with respect to interest rate, insurance and tax in non-linear form. Shovel and truck annual productivity constraint, fleet matching constraint and number of truck per shovel constraint are incorporated in this optimisation problem with continuous variables. This formulation will yield total cost minimisation per hour and good accuracy compared to previous methods.

Dec 6, 2010

By A. Berry, N. R. Banerjee, C. S. Finnigan, M. Fayek, N. J. Bridge

Lac Cinquante is a mineralogically simple, vein-hosted uranium deposit in Archean basement rocks (Angikuni greenstone belt) that originally were unconformably overlain by Proterozoic sedimentary and volcanic rocks of the Baker Lake Group (BLG). Basement rocks are mainly pillowed and massive tholeiitic lavas (N-MORB) with interbedded tuff; overlying sedimentary rocks comprise a basal talus/fault breccia that grades upward into fluvial sedimentary rocks and subaerial, trachytic volcanic rocks; granite and porphyry dikes (Hudson and/or Nueltin granitoids) intrude the basement rocks. A typical section through the Main Zone comprises 1) laminated ‘tuff’, 2) altered (carbonate-hematite-chlorite) schistose ‘tuff’, 3) a pitchblende-bearing, breccia-vein, 4) altered ‘tuff’, and 5) laminated ‘tuff’. The vein comprises brecciated chlorite, hematite, and pitchblende with carbonate cementing the breccia. Graphitic ‘tuff’ with sulfide-stringer veinlets locally overlies or underlies the vein. Pitchblende also occurs in the altered rocks and in gash veins that cut basement rocks. U-Pb ages on pitchblende fall into two groups: one at 1828 } 29 Ma reflects primary uranium mineralization, and a second at 1437 } 31 Ma represents resetting. Pb-Pb chemical ages show other resetting events at 1260-1321Ma, 895 Ma, 741-813 Ma, and 660-706 Ma. One possible genetic model for the Lac Cinquante deposit involves leaching of uranium from granitoids and the BLG by basinal brines that migrated to depositional sites where graphitic rocks acted as a reductant. A second model requires that uranium was sole-sourced from the BLG and that granitoid rocks provided heat to drive the hydrothermal system, which leached and ultimately precipitated uranium. The deposit has characteristics similar to vein-type uranium deposits in the Beaverlodge District of Saskatchewan

Jan 1, 2013

By John S. Pack

The last 25 years have seen rapid expansion in the use of helical screw pile foundations and tiebacks for new and retrofit construction of buildings and earth retention structures. An estimated $100 million was spent in 2002 on helical foundations and tiebacks in the United States alone. While design information is available in the literature, information regarding quality control, inspection and performance monitoring is lacking. Recognition of at least one manufacturer's helical foundation material by the Uniform Building Code, Standard Building Code, and BOCA (all three codes now combined into the ICC International Building Code) has given added urgency to the dissemination of reliable and practical quality control, inspection and performance monitoring procedures. This paper describes a set of such procedures that have been followed for 17 years by engineers experienced in the industry who have directly installed or been involved in the installation of over 140,000 helical foundations and tiebacks in divers soil conditions for various types of structures, including earth retention structures. Topics covered include design responsibility, building code listings and requirements, manufacturer ISO certification, manufacturing process, material and installation specifications, installation contractor certification, field placement, installation procedures, field inspection, building code inspection and performance monitoring. The paper concludes with a step by step example of practical quality control, inspection and performance monitoring procedures on a typical helical foundation project.

Jan 1, 2003

I had hoped when the time came for me to address this meeting that gold mining would be in a much happier position than we find it to-day.As it is, and because of the demands of national security, we find this great and valuable primary industry relegated to the background and in danger of temporary extinction.These notes refer mainly to gold mining in Western Australia, whence comes the major portion of Australia's production, and their purpose is to record a brief review of the industry immediately prior to the general disorganization that is following the call-up of men from the mines.During this period of reduced production the loss of comparable statistical data will make it impossible to follow the progress of the industry, and, since the period may be long, it occurred to me that information might be derived from an examination of the trend of recent production that would indicate what may be expected of the industry when full production is resumed in the future.Since the revival of gold mining, which started in 1931, most of the old-established mines have reorganized and, in some cases, completely renewed and enlarged their equipment in order to achieve maximum production, and old mines hitherto unpayable have been re-opened and equipped. At the same time large sums have been spent in scientific prospecting and in search for new mines, and it is safe to say that at the end of 1939, when gold production reached its peak, practically every known mine in Western Australia that could be worked profitably was in production.During this period the number of men employed in the industry rose from 5,961 in 1931 to approximately 15,000 in 1939. From the outbreak of war in 1939 to the end of 1941 the output from the mines was maintained at full pressure, maximum tonnage beingrecorded in 1940, although a reduction in the grade of ore treated caused a slight falling off in gold production.During 1941 there was a. fall in both tonnage and grade. The decline in tonnage was due partly to the closing of the Lancefield and Mount Magnet mines, and partly to the shortage of labour brought about by the response of the goldfields to the call for men for the fighting services, the average number of men in the industry in this year being reduced to 12,929.With the entry of the United States into the war in December last and the pooling of the resources of the allied nations, the need for gold as a purchasing medium passed, and with its passing there arose the demand for the transfer of the man-power engaged in gold mining to other fields of industry directly connected with the war effort.There was a ready response by those connected with the industry who...

Jan 1, 1942

By Thomas J. Weaver

Piles extending through soft soil near the ground surface will have a relatively low lateral stiffness. As a result, lateral serviceability limits may control the number of piles required for foundation support. Improving near surface soil properties may significantly increase lateral pile stiffness and thus reduce the number of piles required for the foundation. A series of analyses have been performed to assess the depth and lateral extent of soil improvement required to significantly increase lateral foundation stiffness. Analyses consisted of Winkler type beam on a spring foundation and three-dimensional, linear elastic finite element analyses. Results from the analyses show that lateral pile foundation stiffness can be doubled when soil properties are improved to a depth and lateral extent of 5 pile diameters. In order to achieve this increase in foundation stiffness, the modified/improved soil modulus of elasticity needed to be approximately 5 times greater than adjacent unimproved soil. This magnitude of soil improvement over such a limited lateral extent suggests that limited soil improvement can result in more economical foundation designs at soft soil sites.

Jan 1, 2006

By C Maloloy-on, S Morgan, M Deiparine, H Mackie

There is a strong focus in the mining industry to limit its impact on water quality and usage. This is even more evident in developing countries, where mining companies operate within local communities and have to be diligent not to affect them negatively. In mineral processing operations, the vast majority of water reclamation occurs at the tailings thickener area and tailings storage dam. It is often more effective to maximise water recovery at the tailings thickener before material transport to the tailings dam. Tailing dams are relatively inefficient, and experience a high degree of water loss due to evaporation, seepage and water retention. In addition, tailings dams present the biggest environmental liability for mineral resource projects, so it is beneficial to limit their size and loading.In the past, it was common for tailings thickener areas to have a significant footprint with several large diameter conventional thickeners, producing underflows of between 45-55% solids (w/w). At times, these multiple thickeners were difficult to operate, leading to inefficiencies in water recovery and quality. The development of High-Rate Thickeners (HRT) has resulted in improved settling properties and HRTs usually operate at significantly higher solids loadings (= 1.2 t/m2.h) when compared to conventional thickeners (= 0.1 t/m2.h). Subsequently, thickener diameters have reduced in size and HRT technology has become the preferred option for thickener circuit design in both new and existing operations. HRTs also produce higher water recoveries with increased underflow densities = 55% solids (w/w).The Carmen Copper Corporation (“Carmen Copper”) circuit upgrade is a recent example of these HRT benefits, where one, 39 m diameter, Outotec HRT treats the solids flow rate of five 76 m diameter conventional thickeners. This has allowed operations to increase dry plant tonnage by 50%, maintain key performance targets and provide a framework for further plant expansion. This paper details the sustainable approach to the Carmen Copper tailings thickener upgrade, where metallurgical performance, cost-effectiveness and environmental impact were key considerations.CITATION:Morgan, S, Mackie, H, Maloloy-on, C and Deiparine, M, 2015. Carmen Copper – a sustainable approach to tailings thickener upgrades, in Proceedings MetPlant 2015, pp 416–430 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Raymond A. Mazzoni

Over the last twenty years, roof support technology has made numerous advances since the original wedge and slotted bolts of the 1950's. By comparison, the roof supports used today are more complex and specialized than the supports used in the past, providing mines with a varied selection of supports from which to choose. As a result, when problems with supports are encountered, it is more difficult to determine whether it is the result of geological changes, poor installation practices, or malfunctioning supports. Recognizing this problem, MSHA's Roof Control Division of the Pittsburgh Safety and Health Technology Center, has undertaken the task of publishing a guide for trouble¬shooting problems encountered with roof support systems. The purpose of this guide is to provide a logical sequence to resolving the most common problems encountered with roof supports. The objective of this paper is to introduce this guide to the mining industry as well as provide insight into the evolution of the guide from its beginnings as rudimentary charts to its more comprehensive present format as a practical guide for use by the mining commu¬nity.

Jan 1, 1997

By J. Willan

This paper addresses the problem of designing a destress blasting procedure to reduce the incidence of rockbursting in hard rock mines. A review is made of the developed theory and practice of destress blasting in rockburst-prone ground. Specific reference is made to a recent survey of past and current practice with particular reference to Ontario mining operations. The need is identified for a more scientific basis for destress blast design and monitoring. Reference to developments in blasting technology as well as rock mechanics are then made to support a proposed, integrated design procedure and research strategy.

Jan 1, 1984

The Canadian mining industry is one of the strongest in the world. Not only does the country produce a sizable amount of minerals and metals, Canada plays host to hundreds of global mining companies, large and small. The country, for the most part, recognizes the importance of natural resource development, particularly mining, to its economic well being. Like any country, though, there are federal and provincial regulations on the books that the industry takes issue with. But there are also certain economic incentive programs in place to encourage exploration and mine investment. And, unlike the industry and the United States government, the Canadian government and mining industry appear to have a reasonable working relationship.

Jan 4, 2010

Whilst the fossil fuel-based power industry moves towards carbon capture and storage (CCS) or so-called 'geosequestration', the minerals industry should adapt to reap the benefits of the new technology. If CCS becomes viable, the door is open to potential key developments in mineral processing. For example, truly continuous steelmaking could at last be realised using natural or manufactured gas combined with generic melt circulation. Iron ore fines would form a thin molten layer moving countercurrent to the gaseous reductant on one side of a melt circulation loop with efficient post-combustion without deleterious effects of slag accumulation on the other. This eliminates oxygen steelmaking because carbon has no access to the circulating molten iron. Steelmaking merely requires addition of the appropriate low level of carbon and in-line impurities removal to meet product specification. Concerning non-ferrous smelting, nothing short of virtually zero gas emission will be acceptable in the future. For dolomite-hosted Zn/Pb sulfide ores, typified by those in the Carpentaria region of Northern Australia, the way forward proposed is sulfur fixation at the mine site employing the highly exothermic reaction of SO2 with dolomite, followed by encapsulation of sulfated dolomite in fused ore slag. This releases enough energy for direct ore smelting to individual metal products. However, without CCS the strategy would be unacceptable because of greenhouse gas emissions. The scheme is advocated for direct ore smelting at McArthur River. As a result, the environmental problems of disposal of flotation tailings are avoided. Also, highly energy intensive ultra-fine grinding is eliminated, as indeed froth flotation itself, with overall very significant energy savings and exceptionally high increases in metals recovery. Zinc and lead recoveries approaching 99 per cent are predicted to be entirely feasible.

Sep 13, 2010

? CONSTRUCTION AND MINING COSTS ARE HIGH IN THE ARCTIC ? VERTICAL KIMBERLITE PIPES WITH HIGH STRIP RATIOS ? SITE SPECIFIC GEOMETRIC CONSTRAINTS ? OPEN PIT FOLLOWED BY UNDERGROUND MINING ? HIGH KIMBERLITE UNIT COSTS TRACK INSTALLED ON PIT WALL ? INTENDED TO REPLACE MAIN HAUL RAMP ? 5 MIN HOIST CYCLE TIME ? KEY ADVANTAGES - REDUCED CYCLE AND STRIPPING RATIO ? TECHNOLOGY EXISTS IN OTHER APPLICATIONS

May 1, 2003

Jan 1, 1998

By Robert A. Cummings

A rock mass classification system has been developed for support estimation in mines using caving methods. The developed system (MBR System) accepts readily-obtainable geotechnical properties, and mining geometry, to develop a rating that permits recommendations for drift support in block caving mines. The data base includes major active United States caving mines. The method is intended to be used for planning and estimating purposes and for preliminary support design. The Manual explains the organization and nature of the MBR System, its derivations, details of required input data, methods for assessing the data and for developing rock mass ratings, and techniques for selecting the most appropriate mine support recognizing mine requirements and desired stability. A worked example is provided.

Jan 1, 1984

By J. F. Shea, O. F. Tangel

Battelle Memorial Institute participated in a program for the General Services Administration aimed at developing a nickel-cobalt separation process that could be integrated in the Nicaro nickel plant. At the time the programwas being carried out, the Nicaro process was a straight-through operation, in which the ore was reduced and leached, after which the pregnant solution was boiled to produce a so-called "bulk precipitate" which contained virtually all of the nickel and cobalt which had been dissolved in the leaching step. The weight ratio of nickel to cobalt in Nicaro ore is approximately 15 to 20:l. The weight ratio of nickel to cobalt in the finished product had to be 100:l or higher to meet specifications. Because the Nicaro process embodied no nickel-cobalt separation step, the only way that a bulk precipitate of the specified nicke1:cobalt ratio could be produced was to so adjust roasting and leaching conditions that nickel would be selectively leached and most of the cobalt would be rejected with the tailings. The required selectivity, however, was achieved at the expense of nickel recovery, which was 5 or more per cent less than might have been obtained with the existing equipment, utilities, man power, etc., had selectivity been no object. The over-all purpose of the program was to develop a separation step that could be fitted into or onto the Nicaro facilities and which would permit the manufacture of a product that would meet the desired specifications and still permit the recovery of a maximum amount of nickel. Battelle suggested that this might be accomplished by reprocessing off-specification bulk precipitate and specifically suggested the process based on ammonium sulphate leaching followed by hydrogen reduction of the leach solution according to techniques developed commercially by Sherritt Gordon Mines Limited. Such a process would not only satisfy the objectives of the research but would present two additional advantages. (1) It would produce a separate cobalt product which could be further processed into metal, alloys, oxides, or salts. (2) It would yield nickel in metallic form which might be more generally marketable and command a slightly higher price per unit of nickel than the Nicaro oxide product. DESCRIPTION OF THE PROCESS Figure 1 is a flowsheet of the process. The essential features are: (1) Extraction of about 97 per cent of the nickel and about 85 per cent of the cobalt from bulk precipitate by a principal leach with ainmonium sulphate solution (Step A). Extraction of virtually all of

Jan 1, 1961

By Andrew Peterson

The Maine Department of Transportation offered this challenging design-build project for a new, 12-span, bridge over the Kennebec River in Bath, Maine. This structure would be built to replace the existing Carlton Bridge connecting the village of Bath, Maine to neighboring Woolwich, Maine. The design build team of Flatiron Structures, Inc., and Figg Engineers, Inc., elected to design and build a segmental concrete bridge. Site conditions dictated that this bridge would be supported primarily on deep foundations. Case Foundation Company joined the project team in the winter of 1997 to install twenty-two, eight foot diameter drilled shafts. The drilled shafts were designed with 8' diameter, permanently cased shaft sections and 7.5' diameter rock sockets. Shaft lengths ranged from 20' long near the river's edge to 100' deep in the middle of the river. Rock socket lengths ranged from 12' to 30' deep. Two Osterberg Cell load tests were conducted on production drilled shafts. Figg Engineers utilized the results of the load tests to "fine-tune" the rock socket design during construction of the drilled shafts. Construction of the drilled shafts proved to be very challenging and called on every member of the design-build team to work together throughout the project. One of the most challenging aspects of this project was in the installation of the 8' diameter permanent casing and drilling of the rock sockets. Early in the project, it became apparent that the top of bedrock was broken and unstable. This condition limited the advancement of the permanent casing and the affect of a "seal" at the top of rock socket. As a result, as the rock socket was advanced, loose material spilled into the hole and stopped progress of the socket. In order to resolve this problem, the design-build team developed a redesigned drilled shaft which included the installation of a steel sleeve to seal off the unstable rock formation. Following installation of the sleeve, the rock socket diameter was reduced to 7' diameter and advanced additional length to achieve required design capacity. All drilled shafts were installed with equipment supported on floating barges. Water access, along with the long shaft lengths and very hard bedrock required the use of cranes and drilling equipment that far exceeded the requirements of typical drilled shaft projects. This paper will discuss the relationship between design, construction, and equipment utilization on this challenging design-build project. [ ]

Jan 1, 1999

By Murray Wood, Michael Schaffer, Makat Katom

"An expert system applied to the control of mineral process unit operations is, by its nature, the site best operating practice, having been designed by the local experts in conjunction with consulting metallurgists. The “common sense” layer in a MET (MinnovEX Expert Technology) solution determines an appropriate action for the current operating conditions through a developed heuristic model of the process (expert system). The magnitude of the setpoint change that is made is proportional to the confidence that the system has in its interpretation of the current conditions (fuzzy logic). The solution is always striving to take the process to a constraint and thereby optimise the operation. An accepted limitation of the solution is that the only way the system can determine if a constraint has been reached is to exceed it and then withdraw – essentially “experimenting” with the process. By leveraging a model, which can accurately ""simulate"" the process, this restriction can be circumvented by pre-testing the set point change through a ""what if"" analysis and then modifying the solution as appropriate.At Ok Tedi, the introduction in 1999 of a MET expert system for SAG milling resulted in significant improvement in circuit throughput. Yet, with the additional inclusion of an accurate model of the process there was still more that could be achieved. Hence, in 2002 a MET Neural Network model was developed and deployed to enhance the existing expert system solution. The principal objective of this model was predicting the effect that changes in SAG tonnage and density would have on the power draw of the mill - essentially a power predictor. The results have seen a decrease in process variance with an associated increase in average circuit performance.This paper describes the methodology by which the Neural Network model was implemented, the considerations and limitations when applying this technology and ultimately the results that were achieved."

Jan 1, 2003

By João Carlos Jânio Gigolotti

O avanço tecnológico tem gerado demanda crescente por materiais que possam ser utilizados em alta temperatura e ambientes oxidantes, o que inclui ligas intermetálicas MR–Si–B (MR = metal refratário) com estruturas multifásicas. Assim, este trabalho teve por objetivo estudar a microdureza de ligas do sistema Hf–Si–B na seção isotérmica a 1600ºC, na região rica em Hf. Ligas Hf–Si–B foram fundidas com lâminas de Hf (min. 99,8%), Si (min. 99,998%) e B (min. 99,5%), em forno a arco e tratadas termicamente a 1600 ºC em atmosfera de argônio. As relações de fases nessas ligas foram identificadas por difração de raios-X e por contraste, em imagens obtidas via microscopia eletrônica de varredura no modo elétrons retroespalhados. As ligas tiveram sua dureza medida pelo método Vickers (microdureza) com cargas de 0,05 kgf e 0,2 kgf e tempo de aplicação de 20 s. Os resultados, obtidos da média aritmética das medições realizadas nas regiões heterogêneas de cada liga, mostraram uma dureza média de 11,08 GPa, com pequeno coeficiente de variação de 3,8%. Os boretos HfB2 (19,34 GPa) e HfB (11,76 GPa) apresentaram dureza mais elevada que os silicetos Hf2Si (8,57 GPa), Hf5Si3 (9,63 GPa), Hf3Si2 (11,66 GPa), Hf5Si4 (10,00 GPa), HfSi (10,02 GPa) e HfSi2 (8,61 GPa).

Aug 17, 2017