Search Documents

By Chantale Doucet, Yves Lizotte, Alan Cameron

A joint Federal Government-Industry research project on the effect of geology on the fragmentation of rock excavated by blasting in underground developments was conducted at the CANMET Experimental Mine, near Val d’Or, Quebec. A total of thirteen (13) blasts were studied from November 1994 to February 1995. The analysis of each blast was divided into three stages: pre-blast characterization, including structural mapping, assessment of Rock Mass Ratings (RMR), Tunneling Quality Indices (Q), blast design documentation; blast characterization comprising blast vibration monitoring and analysis; and post-blast assessment comprising fragmentation assessment by digital photoanalysis, calculation of half cast factors and measurements of bootlegs.

Jan 1, 1996

By Lawrence W. Hallanger

Anaheim Bay, located at Seal Beach, California, is the site of the Huntington Harbor development of waterfront homes and marine facilities. The main entrance to Anaheim Bay is a relatively narrow channel connecting the bay with the Pacific Ocean which runs under California State Highway One. During the development of Huntington Harbor the old highway bridge was replaced with a new, higher bridge to allow for boat passage through the channel. At that time only the main span decking of the old bridge was removed, leaving the support pillars and the approach ramps in place (see Figure 1). The narrowness of this channel, plus the increasing boat traffic created a situation in which public demand for the removal of the old bridge became significant. Because the bridge was located within the boundaries of the Seal Beach Naval Weapons Station (see Figure 2) the Navy became involved in the bridge removal. Eventually the task was assigned to the Naval Amphibious Construction Battalion One and work began in early 1974.

Jan 1, 1975

By Evan Jannoulakis, Wilfrid Comeau

Using the Scaled Distance (SD) and the vector sum Peak Particle Velocity (PPVvs) from a single delay, preferably single blasthole, in a shot, a number is derived which has shown itself to be consistently related to blasting efficiency, as experienced by one of the authors of this paper over the last thirty years. The numbers derived by this process range in value over one order of magnitude more or less. This variation, a function of distance, weight of explosive in the delay, blasthole diameter, blast design, powder factor and the geological environment, can be consistently related to two of these factors, powder factor and distance. In actual use the measured "BED" representing good blasting results should not vary by more than + 33 to + 50 percent of the estimated "BED" in non calibrated cases, and + 10 to 20 percent where previous experience is available. Relatively high "BED" values are indicative of poor blasting results while relatively low "BED" values may be precursors of poor blasting results in a shot. There are many variables in the geological environment which can affect the "BED". A case study is presented from a surface coal mining operation in eastern Canada. This case study tries to evaluate the reasons for the variability in "BED" values derived from multi-hole shots. A problem in using "Signature Vibrations" from a single-hole shot to predict blasting vibrations from multiple-hole production shots is identified.

Jan 1, 1998

By J Lyall Workman, Peter N. Calder

"Presplitting is a technique mines and quarries may use to produce high quality final pitwalls. Damage from backbreak can be minimized, thereby insuring the final pit walls standat the designed angle. Thus costly excess waste removal is avoided. Safety in the pit isenhanced. Control blasting is an essential component of procedures to maintain the stabilityof final pit walls prone to failure."

Jan 1, 1993

By Clayton Thompson

Linear detonation wave generators (DWGs) shape a detonation wave so that every portion of the wavefront reaches the target “line” simultaneously. A projection-type linear DWG uses Gurney plate velocity predictions and Taylor deflection angle predictions to estimate the angle at which a thin projected flyer (typically metal) will impact a target. A mousetrap-style planar DWG consists of two projection-type linear DWGs working in succession to create a planar wave-front through shock initiation of each successive target explosive. The angle of deflection is critical to yielding a planar or linear wave profile. Gurney predictions, nominally accurate to within 10% of empirical results, may not yield ideal linear or planar detonation behavior when used with a grazing projection-type DWG, which typically requires accuracy within 2%. Simulations were conducted using AUTODYN hydro code to compare deflection angle prediction methods. Ranges of minimal error between Gurney and Taylor predictions and the results from the hydro code were determined, using PBX-9404-driven polyethylene flyers.

Jan 1, 2011

By Robert Hopler

RBH Note: in 1913 black powder was still dominant as a coal-mining explosive, but permissible explosives were making some slight headway. For example, in 1902 there were only 11,300 pounds of permissibles used in coal mining, but in 1913 the quantity was 21,801,285 pounds. However, there were 187,551,653 pounds of black powder used that year. It took many years before the use of black powder ended in coal mining. From the picture of the miner reparing his explosives it’s hard to tell what he’s using, but the fact that a wooden Du Pont powder box is shown, he’s probably not using black powder. That doesn’t mean he’s using a permissible, either, since that was not yet a requirement. It’s interesting that the miners have open flame cap lamps, and the miner is actually smoking a pipe while preparing his explosives.

Jan 1, 2014

By E. Contestabile, B. von Rosen

On August 5th, 1998, a tractor-trailer carrying approximately 18,000 kg of blasting explosives, struck a rock face on the side of the road near the town of Walden, Ontario. Eye-witness accounts of the incident state that there was an intense fire for approximately 30 minutes before the detonation. The detonation caused severe damage to the tractor-trailer, shifted the pavement and caused blast damage to the rock face. A rock fragment was recovered almost 2.5 km from ground zero and a 70 kg piece of an axle assembly was recovered over 1 km from the site. Windows were cracked at distances of almost 3 km.

Jan 1, 2001

By D. C. Valdemeri, Oppermann J. P. Z., R. G. Schaarschmidt, C. S. Mendonca

This case study was conducted in an aggregate company, located at Estância Velha town, RS, Brazil. The study was based on the results of vibration monitoring mainly in terms of PPV (peak particle velocity) and frequency. Changes in the blasting design were performed to adjust the limits determined by the Brazilian standard NBR 9653:2005. Understanding the seismic wave attenuation for the site, changes in the blasting design were tested to fit the limits, such as reduction of maximum charge per delay, initiation orientation and sequencing and finally the replacement of accessories like "shock tube" by electronic initiation system. The results are shown below.

Jan 1, 2015

By Bob de Raadt

After a review of the general principles for blasting stacks, the stagnations of two stack demolitions are investigated. The author concludes and demonstrates that MS-delay blasting can be risky under certain circumstances. How this initiation device can still be applied safely to the demolition of stacks is shown in an account of a blasting operation, in which two 106-m (350 ft) -high concrete stacks were involved. The recent discovery of a possible hazard of MS initiation in this field of blasting is an essential contribution to increased safety in blasting tall structures.

Jan 1, 1982

By David Harrison

The Charleroi Locks and Dam (Figure 1) was completed in 1932 and is located on the Monongahela River, approximately 22 miles (35 km) south of Pittsburgh, in Charleroi, Pennsylvania. It is comprised of a 420 foot (128 m) gated dam, and a 720 foot (219 m) by 56 foot (17 m) land side lock which provides for a 16.6 foot (5 m) vertical lift.

Jan 1, 2015

By Jack Eloranta

"Unwanted, dynamic interaction of adjacent blastholes is a well-recognized phenomenon. Timingschemes and products are selected to minimize adverse effects. Large diameter, surface blasting is less prone to dead pressing and other disruptions which commonly plague underground and construction blasters. However, several lines of evidence suggest that fragmentation may be compromised as a result of powder column disruption in large diameter shooting as well."

Jan 1, 2016

By Tony Francelj, D. Scott Scovira, Remi Proulx

The Meikle Mine is a high-grade, underground gold mine that utilizes a primary and secondary stoping method with delayed backfill. The newly developed Rodeo Mine will start production using similar mining methods in late 2001. The combined production for the mines will be 4100 stpd of ore in 2002. Dilution of the secondary stopes resulting from blast induced overbreak of the backfill placed in the primary stopes was an issue identified as being a major contributor to the total mining cost at the Meikle Mine. To address the overbreak issue, a low-density, polystyrene enhanced bulk emulsion was developed and introduced to the mine. The density and energy of the emulsion was varied until an optimal level was reached. The use of a low-density bulk emulsion has greatly reduced the overbreak of the primary stope backfill when blasting the secondary stopes. Benefits to the mines include reduced secondary stope dilution, lowered total mining cost, and increased revenues.1

Jan 1, 2002

By Larry Schneider

In the construction field and to a lesser degree in mining, flagman are often necessary to move traffic and or pedestrians through work zones. Everyone readily recognizes that they are essential for the safety of the general public and the employees on the job. What is not often considered is the safety of the flagmen themselves. Actually, let’s call these employees “flaggers” recognizing the fact that there are as many women as men doing this job. The first problem we need to overcome is the misperception that flagging is a low skill function that can be done by any untrained employee. The reality is that the flagger works in a very hazardous position with serious responsibility for the safety of his fellow employees and the public at large. And to do this job properly re q u i re s that the flagger receive sufficient training before being sent out to the highway. It is also necessary to convince the flagger of the value and importance of their job in order to motivate them to do a professional job.testing, documentation of both, and accurate re c o rdkeeping are key aspects of HM126F. Of course, training and documentation requirements will vary depending on the type of operation involved, and there may be some differences in the application of requirements depending on your jursdiction. Nonetheless, failure to train and properly document such training can result in heavy fines and/or penalties.

Jan 1, 2004

By Josh Calnan, Paul M. Holmgren, Abigail N. Styer

Detonating cord is a staple of the explosives industry, used widely in the civil and defense industries. Detonating cord is a thin, flexible plastic tube filled with pentaerythritol tetranitrate (PETN). It has many applications in mining, construction and military disciplines. For civil applications, it is used to connect and initiate a series of blastholes in a desired pattern. In the defense sector, it can be used as a detonating agent, a priming agent or alone as an explosive charge. Research has been done to understand the initiation and detonation physics on the detonating cord. However, its sympathetic detonation characteristics needed to be further analyzed.

Feb 1, 2020

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes, Kevin Wegman

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptable cost and computational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By Thierry Bernhard, Johan Finsteen, Charles Dowding, Mathias Jern

To bring some clarity to how different standards relate to each other a project was initiated within the European Federation of Explosives Engineers (EFEE). The first part of the project was a literature study and a survey including an evaluation of the answers provided by members of EFEE. The results were presented at the International Society of Explosives Engineers (ISEE) conference in Denver 2020 as well as the EFEE conference in Helsinki in 2019.

Feb 1, 2020

By Luis Huaroc, Jorge Cardenas, José Salvador

One of the current challenges in mining is managing increasingly competent rock conditions within the mine-to-plant value chain, particularly when working with marginal ore grades. This study presents a case from a Peruvian open-pit operation where the mine plan projected a significant increase in rock hardness, as measured by the Axb index (parameters derived from the JK drop weight test). In response, the Drill and Blast Technical Team made efforts to increase the powder factor by reducing drill spacing and increasing the explosive charge, employing high-energy explosives (3,090 kJ/kg). However, this adjustment presented a challenge in achieving the fragmentation required to meet the target throughput of 97,500 tons/day, resulting in a shortfall of approximately 8.7% under the base case scenario. To overcome this technical challenge, the use of locally engineered ultra high-energy explosives was proposed, offering adjustable energy levels ranging from 3,210 to 3,570 kJ/kg. This solution enhanced ore blending strategies, calibrated to specific Axb ranges. The results also suggest that microfractures generated by the energetic blasting designs contributed significantly to downstream improvements. These outcomes demonstrate the value of a fully integrated mine-to-plant strategy, aligning blasting parameters with downstream processing performance to maximize operational efficiency. This solution led to a 10% increase in process plant efficiency, a 16% reduction in specific energy consumption during primary crushing, and a 13% reduction in the SAG mill. Additionally, shovel productivity rose by 18%, and the dig rate improved by up to 35%. Keywords: fragmentation, blending, high-energy explosive, power factor, microfractures, specific energy consumption and Axb model.

Jan 26, 2026

By D E. Shaw, J B. Case, J Gusek

Explosive casting of overburden is defined as the use of explosives in blasting to move overburden to a spoil pile without rehandling. Studies of the economic feasibility of the method, and the formulation of a design hypothesis involving rock properties, and blasthole geometry are presented. These studies indicate that if technical feasibility can be demonstrated to increase surface coal production, considerable economic advantage would accrue to coal mine operators.

Jan 1, 1980

By J P. Tidman, I J. Kirby, G H. Harries

The SABREX computer model is based on the fact that both shock waves and gas pressure are important in describing a blast. The treatment of explosive-rock interactions includes the influence of non-ideal detonation to make use of recent advances in that field. Details of the blast layout are defined from a comprehensive list of conditions the blaster can control (drill pattern, charging and hook-up). The program gives practical and graphic information about fragmentation, muckpile, damage and costs.

Jan 1, 1987

By Alton Dunaway, Kevin Sullivan, Charles Gray, Doug Hall, Kevin Grant, Kelly Thiel, John Paulson, Bruce Leland, Cole Boyd

Beaver (Castor canadensis) are responsible for economic losses exceeding $4 billion over the last 4 decades in the southeastern United States alone. A large portion of these damages occurs to public roads and highways, forests, agricultural resources, and other property from flooding caused by beaver dams. The United States Department of agriculture, Animal Plant Health Inspection Service, Wildlife Services (WS) program is a non-regulatory Federal program directed by Congress to assist resource owners with managing damage caused by wildlife.

Jan 1, 2007