Search Documents

By Gerald Verbeek, David Tara

"When selecting an impact hammer to drive a particular pile, the decision is often based on local experience. In those cases, the contractor falls back on previous experience or draws on the experience of the hammer manufacturer to select the hammer that will be able to do the job. Obviously, a more scientific approach would be to perform a pile driving simulation using one of several commercially available software packages (e.g., GRLWEAP, AllWavePDP or PDPWave).However, this type of analysis requires quite a bit more effort. First, an accurate model of the pile driving process has to be developed, which includes a model of the soil profile at the job site and input into the analysis program. Then, the model must be analyzed to assess whether the combination of hammer, pile and soil model work.Over the years, numerous individuals and organizations have tried to develop something that would fit nicely in between these approaches: something more advanced than a gut feeling yet something that could be done on the back of an envelope; in other words, a “Goldilocks” approach — not too simple, not too complex, but just right.Screening Tool CriteriaThe goals of the approach are twofold: (1) select the appropriate impact hammer to drive an open toe steel pipe or H-pile, and (2) then use the model for the subsequent high strain dynamic testing (HSDT). The Goldilocks approach centers around five different criteria.1. Maximum Driving StressTo minimize the risk of damage, the maximum driving stresses are generally limited to 80 to 90% of the yield stress (fy) of the steel section. This approach does not consider issues such as hammer alignment, initial imperfections, denting and/or elastic buckling, and pile material fatigue history. However, even when these issues are not applicable, limiting average stresses to 0.9fy or even 0.8fy does not necessarily mitigate the risk of pile damage (Mostafa, 2011)."

Jan 1, 2017

By Stephan Jefferis

It is my understanding that the Scandinavians have done some fundamental work on durability. I have seen a study published whereby the author, Helen Anderson, comments on the durability of polyurethane grouts and there was -if I am not mistaken- a reference made to another Scandinavian testing institute comparing durability of the polyurethane to cement grout under the same type of circumstances. Circumstances are important so we should actually ask the gentleman to shed some light on this particular method because apparently Scandinavia is the place where durability has been taken very seriously and has been well researched.

Feb 10, 2003

With respect to liability damages, claims and costs thereof relating to or ansmg out of contamination, special or non-special wastes, hazardous wastes or pollution in connection with the performance of this subcontract: It is understood that the subcontractor's work and responsibility wholly exclude any requirement to handle such contaminants or to otherwise be responsible for such contaminants, and Subcontractor shall not be nor be considered to be a generator of such contaminants. Contractor shall indemnify, defend and save harmless Subcontractor and its sureties, from and against all liability, damages, claims and costs relating to or arising out of contamination, special or non-special wastes, hazardous wastes

By Takeru Fukaya, Tsutomu Namikawa

"The bending tensile stress occurs in the ground improvements when external forces are applied to the column and wall shaped ground improvements. Therefore, in the design of the column and wall shaped ground improvements, the tensile properties of the cement-treated soils become a predominant factor when the external forces induce bending moments. Then the tensile properties are required to design the ground improvements rationally.Three points bending tests are conducted to investigate the bending tensile properties of cement-treated soils in this study. Cement-treated soils mixed in a laboratory are used in the bending tests. The test specimens are prepared with the several mixing properties to study the relationship between the tensile properties and unconfined compressive strength qu. Bending tensile strength Tfb and fracture energy Gf of the cement-treated soils are evaluated from the load-deflection curves obtained from the bending tests. The experimental results indicate that Tfb and Gf are approximately proportional to qu.INTRODUCTIONThe ground improvement by deep mixing has been widely used for structure foundations, retaining walls and liquefaction mitigations. Recently column and wall shaped ground improvements by deep mixing method have been applied for economical reason. When external forces are applied to the column and wall shaped ground improvements, the bending tensile stress occurs in the ground improvements. Therefore, in the design of the column and wall shaped ground improvements, the tensile properties of the cement-treated soils become a predominant factor when the external forces induce bending moments. Then the tensile properties are required to design the ground improvements appropriately.Namikawa et al. (2007) conducted the finite element analysis to investigate the dynamic behavior of the lattice-shaped improved ground for liquefaction mitigation. In the analysis, an improved ground consisting of several grids in a line was chosen to study the basic behavior of the lattice-shaped improved ground. Fig. 1 shows a example of calculated tensile failure zones in the improved soil during the earthquake. Half of one section of the improved soil consisting of two grids in a line for the 8 m × 8 m grid was modeled in the case. In Fig. 1, the failure occurs at the bottom and upper corners of the improved soil grid. The analysis result indicates that the constitutive model which can appropriately evaluate tensile failure behavior of cement-treated soils is required to evaluate the performance of the lattice-shaped improved ground for liquefaction mitigation. In the analysis, the elasto-plastic model developed by Namikawa and Mihira (2007) was adopted for the cement-treated soil behavior. The elasto-plastic model can suitably describe the tensile failure behavior of cement-treated soils. In the elasto-plastic model, tensile fracture energy is adopted to determine a tensile softening relationship because it is difficult to directly measure the stress-strain relationship after the peak stress state in direct tension tests. However there is little experimental study on the tensile fracture energy of cement-treated soils."

Jan 1, 2015

By Richard Stone, Rouzbeh Afsharhasani, Moses Karakouzian

"Caliche, a hardened sedimentary deposit of calcium carbonate that occurs worldwide, generally in arid or semiarid regions, is frequently encountered in Las Vegas, Nevada. The presence of a caliche layer in a soil profile affects the response of deep foundations to axial load. This paper studies the stiffening effect of caliche layers on the elastic settlement of a pile foundation. In order to evaluate the response in a layered soil-caliche profile, finite element analyses were performed on a typical-sized single pile and a pile group, both having constant diameter and length of the pile. The results indicate that the stiffening effect from the caliche is noteworthy, and a layer with a relative thickness of at least one pile width, regardless of its location, reduces the pile settlement for both single piles and group of piles systems by at least 50%.IntroductionThe presence of cemented materials in the soil profile influences the settlement response of foundations. One type of cemented material that can be found in arid places around the world is a sedimentary deposit of calcium carbonate called caliche. Caliche, a hardened sedimentary deposit of calcium carbonate, is common in arid and semi-arid urban areas, such as Las Vegas, Nevada (Wyman, et al. 1993).Caliche is mostly observed in lacustrine, river, and alluvial fan deposits (Jr.C.C 1970). It is also found in Central and Western Australia, the Kalahari Desert, the High Plains of the Western U.S., and the Sonoran Desert of the U.S. and Mexico.Some conditions required for the formation of caliche are that country or basement rocks must be a carbonate type, carbonate must be present in the soil zone of the area, climate regime is semi-arid to arid, there exists widespread capillary activity, and carbon dioxide (CO2) is present in the environment. As a result, caliche occurs as a product of the carbonization process (Atabey, Atabey and Kara 1998). In such areas where foundations are constructed on thin rock layers (caliche), special geotechnical design conditions should be considered, particularly if the supporting rock layer is underlain by a weaker material."

Jan 1, 2015

By Brad W. Taylor

"During the past several months, I have introduced to civil and structural engineers an innovative solution for the integrity testing of concrete using the Thermal Integrity Profiler (TIP) Wire Cable System by Pile Dynamics. While in the process of “educating” highly-trained professionals about a technological breakthrough, I ended up being educated myself about their needs for quality control/quality assurance (QA/QC). With that in mind, I would like to focus on their two key areas of concern:• How complex is the TIP installation process?• How does the QA/QC engineereffectively analyze and report TIP test results?A few months ago, during a discussion with a senior QA engineer, he asked a question that stopped me in my tracks: “Why should we do foundation testing at all?” Turning it around, I asked, “Why wouldn’t QA/QC personnel want to know everything they could about their critical infrastructure foundation?” Honestly, I didn’t answer his question nor did I fully comprehend what he was trying to say. With his experience, the engineer understood that there has not been an integrity test or a combination of integrity tests that could deliver an inside the cage and outside the cage (cover) complete data set that would provide a definitive profile of the entire shaft. Crosshole sonic logging (CSL) becomes more effective the larger the diameter of the shaft becomes, with a maximum effectiveness between 70% and 80%, but does not provide any data of the integrity of the shaft beyond a straight line between CSL tubes. Gamma-gamma logging (GGL) provides qualitative information about the concrete surrounding the GGL tube and device, and it provides information about a small percentage of the drilled shaft concrete near its outside edge."

Jan 1, 2017

By Sebastian Lobo-Guerrero

Welcome to DFI45! our first on-line annual meeting. We cannot deny the severe impacts that the COVID19 pandemic is having in our industry and our lives. We extend our support to all of our members that have been impacted in many different ways. But through the middle of this difficult and challenging times, our beloved annual conference emerges, trying to re-unite our industry and remind us why we love what we do so much. DFI45 was not originally planned to be delivered virtually, but as our world changed, we adapted. Adversity became an opportunity to re-invent our annual conference. Thanks to the vision of our Organizing Committee, we saw the amazing new possibilities and DFI45 is today a reality. Our theme for this year is People + Purpose + Passion. This theme was decided before the COVID 19 pandemic started, but today it is more relevant than ever before. We are a group of very diverse people at DFI. Our organization includes Contractors, Consultants, Suppliers, and Academics just to name a few sub-groups. But we all have a common purpose and try to find common ground. We are all extremely passionate about what we do, and this excitement is really what makes this organization what it is today. This conference celebrates this passion as you can see in our three main Keynote Sessions. On a local scale, we want to go back and remember the contribution of our industry to our beloved National Monuments in Washington D.C. On a national scale, we want to explore and recap the development of Government Guidelines and Specifications that became the world standards. And finally, we want to close the conference with a session celebrating the family legacy and share amazing stories of families with multiple generations working in our industry. Besides our Keynote Lectures, the conference is full of exciting content such as several case histories, experimental research in deep foundations, applications of new technologies, business aspects and risk management considerations for deep foundations, just to list a few. We also have our now traditional events such as the Hal Hunt Lecture, Awards Reception, DFI Educational Trust 5K Fundraiser, etc. For the first time, all this content will be delivered using different virtual formats, including on-demand presentations, plenary sessions, interactive chat rooms, etc. We are excited about these possibilities. To conclude, we need to recognize the people that against all odds made this conference a reality. First our sponsors, they adapted to the most abrupt change never thought before, and they always stayed there with us, providing unconditional support. Without them no conference is possible. Next, our Organizing Committee that re-invented the concept of an annual conference and found new and exciting ways to make this happen! Our Technical Program Committee led by our Technical Program Chairs, Jennifer Nicks and Gregg Piazza, showed us that nothing is impossible. And last, but not least, the amazing DFI staff that make dreams reality. It has been an honor to serve as the Conference Chair for DFI45. It is an experience that will stay with me for the rest of my career. Conference Chair: Sebastian Lobo Guerrero, Ph.D., P.E. American Geotechnical and Environmental Services (A.G.E.S.)

Oct 27, 2020

By DFI DFI

An Online Conference

By Federico Pagliacci

Continuous Flight Auger (CFA) technique represents an important technological advance in the construction of piles in soft soils. The possibility of excavation under the water table with no need for drilling fluids, along with high productivity, have resulted in this technique?s becoming widespread in many countries. However, CFA technology has limitations because of its difficulty in penetrating hard layers and cross strata with cobbles and boulders. In these situations, pile verticality may be an additional problem. The Cased Augered Pile (CAP) technique consists of penetrating the soil with an auger housed in a casing. Two independent rotary heads sliding along the rig mast operate the auger and the casing. By adjusting the height of the casing shoe and auger bit according to soil type, it is possible to drill piles in very severe conditions - in the presence of cobbles and boulders - and to socket the pile into the rock. The use of a steel casing enables improved pile verticality. Therefore, the CAP technique is also used to construct secant piles to be used as diaphragm walls. The limitations of this technology are the depth, usually no more than 27 m (88 feet), and the size of the rig that supports the drilling tool, no less than 70 t (77 short tons) in working conditions. This paper illustrates CAP technology, the drilling system, and the characteristics of concrete and steel reinforcement and offers a case study of the Palermo-Carini second railway line, which used CAP to construct the new 30 km (18.6 mi) railway line, 20 km (12.4 mi) of which passes through the very congested downtown area of Palermo. More than 300,000 m (186.4 mi) of piles have been drilled in dense calcarenite formations with unconfined compressive strength of 15-25 MPa (2,200-3,600 lb/inch2), soft clay, and silt formations.

By Federico Pagliacci

Continuous Flight Auger (CFA) technique represents an important technological advance in the construction of piles in soft soils. The possibility of excavation under the water table with no need for drilling fluids, along with high productivity, have resulted in this technique’s becoming widespread in many countries. However, CFA technology has limitations because of its difficulty in penetrating hard layers and cross strata with cobbles and boulders. In these situations, pile verticality may be an additional problem. The Cased Augered Pile (CAP) technique consists of penetrating the soil with an auger housed in a casing. Two independent rotary heads sliding along the rig mast operate the auger and the casing. By adjusting the height of the casing shoe and auger bit according to soil type, it is possible to drill piles in very severe conditions - in the presence of cobbles and boulders - and to socket the pile into the rock. The use of a steel casing enables improved pile verticality. Therefore, the CAP technique is also used to construct secant piles to be used as diaphragm walls. The limitations of this technology are the depth, usually no more than 27 m (88 feet), and the size of the rig that supports the drilling tool, no less than 70 t (77 short tons) in working conditions. This paper illustrates CAP technology, the drilling system, and the characteristics of concrete and steel reinforcement and offers a case study of the Palermo-Carini second railway line, which used CAP to construct the new 30 km (18.6 mi) railway line, 20 km (12.4 mi) of which passes through the very congested downtown area of Palermo. More than 300,000 m (186.4 mi) of piles have been drilled in dense calcarenite formations with unconfined compressive strength of 15-25 MPa (2,200-3,600 lb/inch2), soft clay,

Jan 1, 2017

By Jim Bruce

No answer required. From the drilling equipment suppliers, but the specifications must be tailored to be project-specific. Yes, the sonic technique is very interesting as we said, and it is not so much as an issue of the magnitude of power, it's about the efficient use of the power. The efficiency of the machine is not necessarily related to size so it is best to talk to the two contractors that supply the service about that. I think it can be scaled down but it is quite a big head, so therefore there are practical limitations on the size of the door it can walk through and also the size of the casings and rods that it can use. You might defeat the economic advantages if you were to use too short casing lengths. Boart Longyear have a low head room machine that can work within an 8 foot verical clearance.

Feb 10, 2003

By Jeongbok Seo

The Dulles Corridor Metrorail Project (DCMP) involves the design and construction of a 23.1-mile extension of the Washington Metropolitan Area Transit Authority (WMATA) rail system. The initial 11.7-mile extension, with five transit stations and a new service and inspection yard, is to be constructed. The construction plan for the initial 11.7-mile extension includes installation of a total of an estimated 4,250 or 160,000 linear feet of driven 12x53 steel H-Piles at more than 80 different locations. At the time of this paper, approximately 40 percent of the piles have been installed and the remainder of piles will be installed by the end of 2010. This paper describes: 1) subsurface investigation program, 2) application of existing Codes and impact on the design of H-Pile, 3) design methods to determine geotechnical bearing capacity and pile tip elevation, 4) verification of capacity including PDA and Static Load Tests, 5) project specific pile load tests, and 6) QA/QC during pile driving.

Jan 1, 2010

"After the non-destructive testing is completed, the data must be compiled, evaluated, and interpreted. During this process, the data may indicate that there is an anomaly warranting further investigation, which may eventually be determined to be a flaw or defect. The definitions of an anomaly, flaw, and defect can be described as follows (after Amir, 2002):Anomaly - Any irregular feature identified in the NDT graphic results. An anomaly may be due to the testing instrumentation (such as noise), to the means used to perform the test (e.g. access tube debonding in CSL) or to the shaft itself. It is the responsibility of the NDT practitioner to gather and analyze all relevant data and try to resolve every anomaly before it is declared a flaw or defect.Flaw - Any deviation from the planned shape, size and/or material of the shaft.Defect - A flaw that, because of either size or location, may detract from the shaft’s intended performance or durability. The geotechnical engineer and the structural engineer are jointly responsible to decide which flaw comprises a defect.This section describes the process of evaluating the data, determining if an anomaly exists, and if so, deciding whether the anomaly is actually a flaw or a defect. If the anomaly is determined to be a defect, its effect on the performance of the shaft must be evaluated, and if necessary, the can be re-engineered, repaired, or replaced."

Jan 1, 2004

By Donald T. Robertson

This paper presents case histories of driven concrete pile damage detected with dynamic testing methods utilizing strain gages and accelerometers embedded in the pile at the prestressing yard during pile construction. Data from the embedded instrumentation is compared with data taken with external bolt on instrumentation and other test methods such as low strain testing on the same pile. In the most severe cases, the piles were extracted revealing and corroborating the embedded data collector results.

By Sherif Elfass, Gary Norris

Bi-directional load testing of drilled shafts has been widely adopted as a means to evaluate their load carrying capacity. However, in order to reach failure, most of these tests are carried out on sacrificial shafts using expensive sacrificial elements such as hydraulic jacks. A proposed low-cost bi-directional testing technique is discussed. It mechanically loads the end bearing soil below a drilled shaft, against its side shear resistance. The technique was originally established as an alternative to post-grouting to reliably account for the forfeited end bearing resistance. However, since it loads the shaft in a manner similar to conventional bi-directional tests, it can be used to not only load test sacrificial shafts, but production shafts as well. Furthermore, unlike conventional bi-directional load tests, the load is applied through surface jacks. These jacks, along with other load test components, are movable and can be reused to load test all the shafts of the project thus presenting an economic benefit. The concept of this technique has received favorable feedback from a few consulted departments of transportation, and while promising, has not been field tested to date. A U.S. patent was issued for the tip loading module and the loading technique described.

Sep 8, 2021

By Jim Henry

I would say mainly the cost. I showed only 3 cases. One of them was the one that Allen just described and there were two other cases. In those cases it was fairly easy to develop a solution using limited mobility grout to treat the soft soils suitable for the limited bearing pressures required by the structures. LMG readily provided a fairly reliable system for the foundation support at a reasonable cost.

Feb 10, 2003

By Grischa Dette, Thomas Schröder, Holger Merski

For the construction of the tunnel for the new Berlin S21 light rail line, a construction pit had to be built below the crossing B 96 federal road. For this purpose, the construction pit M’ has been built beforehand as a preliminary structure for the later S21 Berlin. A crucial element of this structure is a 2.50 m deep reinforced concrete deck slab which carries the B 96. During the later construction of the S21, it became clear that the existing preliminary structure could not be used without major modifications. Consequently, the construction pit design was gradually upgraded – still with the aim of retaining the basic concept of a trough structure with a jet-grouting cut-off. As construction progressed, for reasons of stability it became necessary to develop a fundamentally new concept with an underwater concrete base replacing the jet-grouting cutoff. This paper describes the planning and construction of a cut-and-cover structure with an underwater concrete base – a layout that brings with it the difficult task of underwater excavation and concrete placing without direct accessibility from above. Special emphasis is placed on describing the innovative approaches in connection with a remotely controlled underwater dredger from the Norwegian offshore industry for excavation works. Furthermore, the sophisticated underwater technologies for concrete placing in the confined surroundings are described.

May 1, 2022

By Dave Paul

Dam rehabilitation involves a range of design, construction, and operation risks, some of which are not encountered in new dam construction. These risks can have significant impact on project schedule and project budget. Owners, engineers, and contractors need to understand these risks. Existing dams typically were designed in an era of design and construction standards that have been upgraded and changed. Modern standards will impact the construction approach taken and involve understanding the earlier standards. Knowledge of historical standards/practices as well as current design standards and construction methods is valuable for developing and designing rehabilitation components. Construction records and as-built drawings are valuable when they are available. Rehabilitation projects often consist of older projects where as-built documents or construction records are not available. Where these records exist, many (most) times, they do not fully reflect the current conditions within the dam and appurtenant works. leading experienced practitioners to “expect surprises” both during investigation of the existing facility, as well as during construction. “Surprises” should be expected even when historical records of investigations, design and construction are available. Unknowns, be they known unknowns or unknown unknowns, can be planned for by developing an approach for the design and construction process to identify potential issues/problems, or at least alert the designer and contractor of potential issues. A Risk-Based approach applied for the entire life of the rehabilitation project can be used to alert the parties of potential “surprises” and provide direction for mitigating issues as they arise. This type of approach is particularly effective when the process includes senior practitioners with decades of design and construction experience in all aspects of dams. Minimizing impacts created by “surprises”, particularly during construction, can result in an improved project meeting budget and schedule goals and design standards. This paper identifies and categorizes risk types salient to dam construction, reviews the process of risk identification and analysis, discusses guidelines for risk allocation, reviews strategies to mitigate risks, presents several case studies where risk mitigation strategies were employed successfully (or unsuccessfully), and presents lessons learned. The paper concludes with a summary and recommendations for best practices for Project Risk Management and mitigation that can be used by: Owners; Design Engineers; and Construction Managers, in planning, design, pre-construction and construction phases of dam related projects.

By Dale Berner, Michael O’Sullivan

"This article focuses on lessons learned from innovative designs including in-the-wet construction methodology and modified foundation conditions, for two United States Army Corps of Engineers (USACE) megaprojects. Olmsted Dam FoundationThe over $2 billion Olmsted Dam on the Ohio River is currently under construction 16 mi (29.6 km) upstream from the confluence with the Mississippi River. The project is under the jurisdiction of the Louisville District of the USACE. It will consist of an 800 ft (244 m) long tainter gate section, a 1,400 ft (427 m) navigable pass, two boat abutment sections, a fixed weir section, and upstream and downstream scour protection. The Olmsted Dam and its two 1,200 ft (366 m) locks, which were built in 2002, will eventually replace both Locks and Dam #52 and #53, both built in 1929, and thereby bring significant benefits to the Ohio River navigation system.In 2002, the Jacobs/COWI JV completed the design of the dam; which was an engineering challenge for several reasons. A significant consideration was its proximity to the New Madrid Fault, which could impose an 8.4 Richter scale seismic event on the structure, which is located in an area of potentially liquefiable alluvium. The extensive seismic analysis performed by the designer included a response spectra analyses, lateral pushover analyses of pile foundations, hydrodynamic added masses, pile group effects, and the development of kinematic motions as a result of the soil-pilestructure interaction."

Jan 1, 2016

By Jeff Hopple

"Bluestone Dam in Hinton, W.Va., along the New River, is owned and operated by the U.S. Army Corps of Engineers (USACE). Completed in 1949, the dam is 165 ft (50 m) tall, 2,048 ft (624 m) wide, and encompasses a water shed that is 4,600 sq mi (11,914 sq km). The Bluestone Dam Safety Assurance (DSA) Program began in 2001, and is a multiple-phase construction project to upgrade the capacity and stability of the structure to meet the probable maximum flood event. Installing 216 high capacity rock anchors was a major feature of the work.The USACE selected Brayman Construction Corporation to perform Phase 2B of the construction modifications to the Bluestone Dam. Brayman was responsible for installing the high capacity rock anchors, which range in size from 3 to 61 strands and have a design load up to 2,145 kips (9,541 kN). Drill holes range in size from 6.5 to 15 in (16.5 to 38 cm), and required full length corrosion protection. Of the 216 anchors, 57 were installed on top of the dam to resist overturning and the remaining 159 were installed on the face of the dam at a 45-degree angle to resist sliding.To gain access to the face of the dam anchor locations, the project required dirt benches, excavations with temporary shoring, and steel platforms. To access anchors on the east and west abutment faces, the team excavated over 10,000 cu yds (7,645 cu m) of material. Support of these excavations included the design and installation of three soil nail walls with over 145 nails and 3,500 sq ft (325 sq m) of shotcrete. The project also called for a 780 ft (237 m) long steel platform to gain access to the spillway anchors. The Stratus Group designed the platform to support two 85 ton (80 tonne) crawler cranes and as many as five drill rigs that were the equivalent to a design load of 3.5 ton per sq ft (335 kN per sq m). Once the final platform design was approved, fabrication of roughly 3 million lbs (1,360 tonnes) of structural steel began. Brayman’s in-house fabrication shop, in conjunction with Dura-Bond Industries and Advantage Steel, collaborated to fabricate and install the platform in less than five months. Flexibility in the platform design allowed for sections of the platform to be lowered as much as 16 ft (4.9 m) to provide access to anchors at lower elevations along the spillway face. In addition to the main spillway platform, Stratus Group, Brayman, Dura-Bond and Advantage designed, fabricated and installed six other unique platforms to facilitate anchor construction on various areas of the dam."

Jan 1, 2014