Search Documents

By Zhang Libo, Wang Xin, Peng Jin-hui, Ju Shaohua, Guo Sheng-hui, Xu Lei, Huang Meng-yang

"China is lacking high grade titanium ores. This work intends to leach impurities such as Fe, Ca and Mg from a low grade titanium ore, to increase the grade. The original material contained 65% TiO2 , 16.12% Fe, 9.4% CaO + MgO, 4.2% SiO2, 1.25% A12O3, and the particle size is between 0.053-0.045mm. Microwave energy was used to enhance the leaching effect. The results showed that when normal heating was used to leach the mineral, the extraction of impurities Fe, Ca and Mg was very low. However, when microwave energy is introduced, the extraction of Fe, Ca and Mg increased dramatically. The optimized conditions are: relative power 5W/g, the ratio of concentrate to HC1 isl5%, leaching at 160°C for 20 min with a ratio of liquid to solid 12:1 mL/g. The material obtained under these conditions contains 92.73% TiO2, 0.207% Ca + Mg, 0.8% Fe, with 94.6% Ti recovery. The poduct meets with the quality for boiling chlorine.IntroductionThe resources of titanium are very abundant, and are distributed all over the world. There are almost 140 minerals containing TiO2 with a content of more than 1%. However, there are only several minerals which can be used for producing sponge titanium. They are mainly rutile and ilmenite. The grade of nature rutile concentrates is higher than 95% TiO2, and it is a high quality raw material. But the resources of nature rutile are relatively low; after mining for many years, its resources are exhausting gradually. Although ilmenite reserves are great, ilmenite cannot be used as a raw material because of its low content of TiO2, only 45-70%; also it has a high impurity content of Ca, Mg and Fe. In these years, there is a tendency for titanium industry to use high grade concentrate."

Jan 1, 2012

By I. Van de Voorde

In this paper, results are presented concerning the search to implement Supported Liquid Membranes (SLM) Technology for the recovery of copper, nickel and zinc from electroplating and other effluents to prevent metal waste. A study of the influence of the individual parameters and of their combined effect on mass transfer in small-scale laboratory equipment has been performed, enabling to set forward the appropiate operating conditions for a pilot plant installation. The SLM pilot plant has been tested extensively, including short and long term runs, with real process solutions. It was demonstrated that the SLM technolgy is applicable for solutions containing 800 mg/L of metal ions, but also to the treatment of solutions with low metal content of origin other than plating shops. It was demonstrated by system analysis that the recycled salts are usable to produce metal electrolytes (for example Watt's nickel bath).

Jan 1, 2003

By K. Osseo-Asare

Rate laws for the hydrogen reduction of metal ions are typically of the form: [r = -d[M(II)]/dt = k[M(II)]xPy2H] where k is an apparent rate constant, [M(II)] and PH2 represent dissolved metal concentration and hydrogen pressure respectively, while x = 0 - 1 and y = 0.5 - 2. Half-order dependences have been reported for some M(II)/H2 systems; however, no satisfactory explanations have been offered. In an effort to bridge this gap in our understanding, the published precipitation rate data (for M(II) = Cu(II), Ni(II), and Co(II)) are reviewed (with emphasis on the reported reaction orders) and compared with the corresponding but limited electrochemical polarization data. Based on the available literature on the electrochemical kinetics of the M/M(II) and H2/H+ systems it is demonstrated theoretically that, under certain conditions (e.g., in the presence of electron-conducting solids), the rate of the M(II)/H2 reaction can be expressed as: [-d[M2+]/dt = k[M2+]2/1P2/12H] It is concluded that electrochemical processes probably play an important role in the hydrogen reduction of metal ions, especially for systems that involve heterogeneous catalysis.

Jan 1, 2003

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Roald Ysteboe, Finn Olesen

"Elkem has developed a process that utilizes SPL as a raw material for pig iron production. This process will be demonstrated in industrial scale during 2008 and 2009. The process developed produce iron, and the reduction material used, is the carbon present in the SPL. The iron source could be either virgin iron ore or waste/recycled material from the steel industry. The SPLrefractory and bath material is dissolved in the slag produced. The slag is designed so that any leaching of environmentally dangerous elements is minimized. This process can in addition to SPL, consume other types of waste derived from the primary production of aluminium. Elkem intends to supply this demo project with SPL and other waste products from external sources, domestic as well as international ones.IntroductionSpent Pot Lining (SPL) is generated when an electrolytic cell for producing aluminium is taken out of service and the refractory and carbon lining is removed from the steel potshell.The yearly generation of SPL world wide is exceeding 500 000 tonnes. The major amount of this quantity is stockpiled or land filled, unprocessed.SPL contain large amount of water soluble fluorides and some amount of cyanides and is classified as hazardous waste in most countries."

Jan 1, 2008

By Harold R. Kokal

Lisakovsky is a 3-billion ton oolitic iron ore deposit in north-central Kazakhstan operated by Orken LLP, a subsidiary of Ispat Karmet and the LNM Group. The iron oxide minerals are goethite and limonite. The gangue occurs as discrete quartz grains and an unidentified form of colloidal silica-alumina. The concentrate produced contains about 49.5 percent iron (Fe) and 0.6-0.8 percent phosphorus (P) or 10-20 times the acceptable phosphorus level. The phosphorus is intimately associated with the iron oxide and colloidal gangue, no discrete phosphorus minerals are found, and beneficiation is not possible. Therefore, to reduce the phosphorus, a hydrometallurgical process that includes roasting followed by leaching in dilute sulfuric acid has been developed. Phosphorus extraction is 70-90 percent, with only a minor loss of iron. The process has been tested in the laboratory and in a pilot plant at 50-300 kg/h. Construction of a 900,000 t/y demonstration plant is underway.

Jan 1, 2003

By Tae-Hyun Kim, Shun Myung Shin, Jin-gu Kang, Jeong-Soo Sohn

We investigated about synthesis of Mn-Zn ferrite with spinel structure using sulfuric acid leaching solution of mixed spent zinc-carbon batteries and spent alkaline batteries. The waste batteries were prepared by physical treatment such as crushing, magnetic separation, and screening. After screening, the crushed batteries were separated to +8 mesh and -8 mesh powder. Among these, under 8 mesh powder was selected for leaching test. The leaching test was investigated at 2 M H2SO4, 4 vol.% H2O2, reaction temperature 60 ?, agitation speed 250 rpm, solid/liquid ratio 50 g/ 500 ml, reaction time 1 h. The leaching efficiency of zinc, manganese and iron were 99.0%, 98.9%, 58.5%, respectively. For co-precipitation of zinc, manganese and iron, 5M NaOH solution was used for pH control. Then in order to synthesize Mn-Zn ferrite powder, it was investigated according to reaction temperature, agitation speed and O2 partial pressure. We could synthesize about 20 nm of Mn-Zn ferrite with spinel structure.

Jan 1, 2008

By J. E. Dutrizac

Mineralogical studies were carried out on nodulated copper cathodes from three primary refineries to characterize the nodular growths and to elucidate the causes of the nodulation. Nodulation is often initiated at the surface of the starter sheet or the stainless steel plating blank, although a layer of smooth copper sometimes is deposited before nodulation commences. In some instances, the "roots" of the nodules exhibit a pronounced dendritic texture that is associated with an abundance of cavities. Slimes particles are not usually associated with these growth features which lead to a globular surface deposit. The globules sometimes develop into larger nodules, and this type of nodulation is likely caused by improper addition agent concentrations. The nodules on most cathodes, however, exhibit "roots" at the contact with the substrate that are associated with microcavities and large clusters (>40 µm) of slimes particles. The slimes constituents are commonly Ag powder, PbSO4 and Cu2(Se,Te) but not AgCu(Se,Te) or Ag,(Se,Te). The size of the slimes clusters, rather than their composition, appears to be the important factor causing the copper to grow into nodules. Tiny individual slimes particles themselves do not appear to cause cathode nodulation.

Jan 1, 1999

By P. K. Narasimhargahavan

This paper discusses briefly the major reasons associated with the growth and its impact on the energy requirement and Environmental imbalance. A projection based on the present global Alumina and Al requirement indicate a substantial further growth of at least 30% over the next 10 years. It is indicated that the main factors which are likely to influence investments are the environmental factors such as the Climate Change and global response to the growing energy prices and sustainable development. Each of the developed / developing nations must find response to the GHG emissions which will encourage the Al Industry to make an effective contribution to global warming while preserving the international competitiveness of the industry - a challenging task. The efforts shall concentrate on improving energy efficiency in the industry possibly of the order of 25% over the next 10 to 20 years. The developments in this line are discussed.

Jan 1, 2010

By Ross Baldock, Ross Andrews, Gu Helin, Lan Xu, Markus Reuter, Song Xingcheng

"A commercial lead smelter using Outotec Ausmelt TSL Technology has been successfully commissioned and put into operation at Yunnan Tin Company Ltd operations near Gejiu City, in Yunnan Province, China. The plant was commissioned in July 2010 after three years in the design and construction phase. The process uses a three stage batch process to produce lead bullion and zinc fume, and a slag that is low in metal values. The paper provides details of this lead smelting project, including the theoretical evaluation of the multi-stage process chemistry, engineering design, plant commissioning and the final operation. Comparison of the design targets and actual performance of the plant is emphasized. The fast ramp-up to full production of the largest Ausmelt TSL lead furnace built to date is highlighted.IntroductionIn 2002, Ausmelt and Yunnan Tin Company (YTC) successfully commissioned a smelter to modernise the Yunnan Tin smelter in Gejiu City, Yunnan Province, China. A single Ausmelt furnace was installed by YTC to process tin concentrate and revert materials, to produce YT Brand tin product. The advanced Ausmelt Technology furnace at YTC replaced seven existing reverberatory furnaces and provided a flexible, energy efficient and environmentally beneficial system to complement the world leading refinery facilities of YTC."

Jan 1, 2012

By Shigeo Asai

History of EPM is described and several functions utilized in EPM are reviewed. Main activities of EPM are summarized with the view on mass production and applications of high magnetic field related to nano-technology. Future trends and prospects of EPM are discussed.

Jan 1, 2006

By María Guadalupe Sánchez-Loredo

Silver from nitrate aqueous solutions was extracted by commercial organophosphorous extractants (tri-n-butylphosphate, Cyanex 471x, Cyanex 301 and Cyanex 302). Quantitative silver extraction was obtained using the Cyanex reagents. After loading, aqueous solutions of several reducing reagents were used to prepare fine silver powders by reductive stripping. Only both extractants Cyanex 471x and tri-n-butylphosphate (TBP) could be reductive stripped and regenerated by aqueous solutions of ascorbic acid, and Cyanex 471x was decomposed to the corresponding phosphine oxide by using sodium borohydride as reducing agent. Silver was recovered as fine particles, which were characterised by means of scanning electron microscopy (SEM). Micrographs showed that the powder size and morphology were directly affected by the composition of the applied organic phases and aqueous reducing media.

Jan 1, 2003

By John Sakala, Jeyapandian Sasikumar, Sydney Kwalela

The Isasmelt Furnace was commissioned in September 2006 with a concentrates treatment capacity of 850,000 tonnes per annum. However, the converter section became a bottleneck to the high throughput. Over 25% of the Isasmelt Furnace down time was attributed to lack of converter space. Factors that affected converter operations were low tuyere line campaign life (an average of 150 blows), high reverts generation, low conversion rates, and high converter cycle time. As a result of efforts carried out to improve converter operation, the average campaign life has increased to over 250 blows and reverts generation has been reduced from 22% of concentrate treated to 15%. Blister copper conversion rate has increased from 15 tonnes per hour to 19 tonnes per hour and blowing time per cycle has been reduced from 5.7 hours to 4.7 hours.

Jan 1, 2012

By M. Rosales

Using the k-e turbulence model, a mathematical fluid dynamics simulation of the flow characteristics in a Teniente converter has been conducted. Two cases were studied: - Transversal sections in the smelting-converting zone; and - A three-dimensional simulation that includes the walls of the reactor The calculations give the velocities field, the gravity waves amplitude, the splashing behaviour, the phase distribution and the shear stress distribution. The latter helps to explain the pattern of refractory lining wear. The calculation includes the approximate shape and dimensions, and the eventual coalescence of bubbles.

Jan 1, 1999

By Qingcai Liu

The effect of the TiC addition on corrosion resistance of the Al2O3-C refractories in smelting reduction melts has been studied by quasi-station immersion and rotary immersion. The corrosion rate of Al2O3-C refractories is decreased with the TiC addition. The corrosion mechanism of Al2O3-C refractories is oxidization of graphite carbon by the oxides of the melts and the formation of deteriorate layer.

Jan 1, 2006

By C. Sui

A common objective in many Cu/Zn concentrators is to reduce the loss of Zn to the Cu-concentrate. One suspected source of the problem is accidental activation of sphalerite by heavy metal ions such as lead. One method of quantifying surface metal ion concentration is extraction with ethylene-diamine-tetra-acetate (EDTA). This was used to survey Cu-rougher flotation at three Cu/Zn concentrators: Les Mines Selbaie, Falconbridge's Kidd Creek division, and Hudson Bay Mining and Smelting Although all have less than 0.2% galena in the ore, Pb ions proved an abundant extractable metal. From a laboratory study a model of surface coverage of lead species generated by an ore was combined with an estimate of surface concentration of lead required to activate sphalerite to explore the possibility of accidental activation. Ores with Pb-grade as low as 0.1% can produce sufficient Pb to be a potential problem.

Jan 1, 1999

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006