Search Documents

By A. Otsuki

"This paper discusses the primary collector adsorption onto a sulphide mineral in mixed collector systems to understand its adsorption mechanism. UV-vis measurements were performed to identify the primary collector concentration adsorbed on pyrite, and the adsorption kinetics under different conditions were compared to distinguish their difference between single and mixed collector systems. Small amount of secondary collector addition prior to the primary collector addition significantly improved the adsorption kinetics of primary one. The result was explained by the combination of two previously proposed mechanisms (i.e., different adsorption site mechanism and multi-layer product mechanism). This study showed UV-vis measurement as an effective tool to study mixed collector adsorption behaviour.INTRODUCTIONCollectors are surfactants composed of heteropolar molecules with a non-polar and a polar group (Lotter & Bradshaw, 2010). In a froth flotation process, the function of collector is to improve the hydrophobicity of target minerals and selectively float them with the aid of gas bubbles. Because of the chemical or physical attraction between the polar group and the mineral surfaces sites, collector molecules adsorb on the particle surface with the non-polar group assigned towards the bulk solution (i.e., water), thus the mineral particle surface becomes hydrophobic (Wills & Napier-Munn, 2006).Thiol collectors are major collectors widely used in sulphide mineral flotation. Potassium amyl xanthate (PAX), dithiocarbamate (DTC), dithiophosphate (DTP), mecaptobenzothiazole (MBT) are some common thiol collectors. Previous studies reported that some mixed collectors systems enhanced the flotation performance (e.g., Bradshaw, 1997; Bradshaw et al., 1998; Rao & Forssberg, 1997). Thiol collector mixtures are often used in the flotation of sulphide ores, and discussed with the synergistic benefits (Bradshaw et al., 1998) which include lowering the total collector dosage requirements, improving the sulphide recovery and the rate of flotation as well as the improving the froth characteristics. The current paper mainly considered the mixture between two thiol collectors (PAX and DTC, considered as a weaker and selective collector, and stronger and less selective collector, respectively (Bradshaw, 1997)) to further understand their adsorption mechanism that should assist in improving the flotation performance of refractory gold ore."

Jan 1, 2016

By Z. Zhang, D. Bouchard, H. Blanchette, A. Lemieux

This paper describes quality control methodologies for the production of semisolid A356 aluminum slugs with the SEED process. A methodology based on destructive tests carried out with an apparatus measuring the force to slice the slugs is presented. The force measurements were correlated with the solid phase morphologies of the slugs and were validated against a non destructive methodology that consisted in monitoring the temperature evolution of crucibles to produce the slugs and the drained metal. Results from the destructive and non destructive methodologies are compared and discussed.

Jan 1, 2006

By Hiwa Salimi, Foley. Stephen R, Loghman Moradi

Common water-miscible organic solvents including DMSO, DMF, methanol, ethanol, acetone and THF in combination with HCl and low concentrations of H2O2 were investigated for dissolution of gold. THF showed the best result demonstrating that gold powder could be completely dissolved in 1.5 hours in 1.0 mol/L HCl and 0.2 mol/L H2O2. No complete gold dissolution was observed for the rest of solvents even after 24 hours. The rate of gold dissolution was measured by dissolving gold wire in THF/HCl/H2O2 mixture. The rate of gold dissolution in optimised condition was 75 g m-2 h-1 at room temperature and significantly increased to 590 g m-2 h-1 by raising the temperature up to 60 oC. Although a THF/HCl/H2O2 mixture showed a slower dissolution rate in comparison with aqua regia, however the applied conditions are considerably milder which is highly promising for gold leaching in an industrial scale.

Jan 1, 2015

By J. C. Hampton, L. A. Matzar, C. R. Gamwell

In geomechanics, conducting uniaxial or triaxial compression tests require samples to be prepared to a certain length-to-diameter ratio. This ratio is typically defined as 2:1 (length to diameter) and is accepted as a common standard for all materials on which mechanical properties testing is performed. Variations in sample length can cause changes in measured strength properties across multiple material types, such as cement, rock, or soil. Within the oil and gas industry, it is not uncommon to receive samples for technical services work that are slightly under or exactly the length requirement before surface grinding and sample preparation. Many of these samples are discarded from uniaxial and triaxial compression tests and used in another manner; therefore, it is necessary to study the length-to-diameter ratio in efforts to understand the limits and validity of testing samples that are slightly out of the 2:1 ratio. This paper discusses uniaxial compression tests performed using Berea sandstone and a standard cement mixture of 2.54-cm diameter to study changes in rock strength and properties. Compressive strength for each lengthto- diameter ratio over a range of 0.5:1 to 2.2:1 was measured. The investigation was extended to study near-end effects, where the sample length is near, but not exactly twice the diameter. It was discovered that the cement samples conformed reasonably well to the suggested ASTM correction factors. The sandstone did not conform to the correction factors and further analysis is required to develop a correction factor unique to the material. Near end effects, in both the cement and Berea, were found to increase compressive strengths, especially when the L/D of the samples was increased slightly over a 2:1 L/D.

Jan 1, 2015

By J. G. Schofield, R. C. Francki, K. M. Donaldson, F. E. Ham

"Developments in pyrometallurgical technology have led to larger furnaces operating under more intense process conditions. In order to maintain the reliability of these furnaces, which are frequently single-line units, the design of the refractories, cooling systems and bindings has become more critical. Traditional thermal and chemical requirements for the refractory to resist slag attack must still be carefully determined. The larger, modem furnaces have placed a new emphasis on the structural properties of the refractories as well as their thermal properties to suit the extensive cooling systems. Based on operating experience, supported by computer models, the refractories and bindings are designed to work together to accommodate the thermal expansions and contractions in order to minimize permanent furnace growth and the risks of leaks. IntroductionElectric furnaces are used extensively in smelting copper and nickel ores and concentrates. Laterite nickel ores and high-magnesia copper, nickel and platinum sulphide concentrates are smelted virtually exclusively in electric furnaces to accommodate the high melting point of the slags produced. Although a number of smelting processes using oxygen-enriched and/or preheated air have been developed to replace reverberatory furnace smelting of conventional copper and copper-nickel concentrates, (lnco, Noranda, Outokumpu, Mitsubishi) electric matte furnaces remain a strong process alternative for these concentrates, either as the primary smelting vessel or for cleaning the slags produced from these processes.The development of large, high-powered furnaces has been an important factor in the growth of electric smelting technology, as evidenced by the list of operating matte and ferronickel furnaces shown in Table I. Because the compressive forces required to maintain a tight, leak-free furnace increase with furnace dimensions, the selection and design of the furnace refractories, cooling systems and bindings require increased attention."

Jan 1, 1993

By G. W. H. Norman

The surficial Archæan rocks of the southern gold belt of western Quebec are constricted near Kewagama lake by granite masses to the north and south. This divides the belt into natural eastern and western parts. This paper deals with the eastern part, extending from Malanie to Haig township. In this section the Keewatin-Timiskaming rocks have a length of about 70 miles and end abruptly against garnetiferous gneisses of the Grenville terrain. In the western half of the section where exploration has been under way since the early twenties, there are sixteen mines that are or have been in operation, and eleven prospective mines. In the eastern half where exploration has been carried on since the early thirties, six prospective gold mines are under development, one· of which, Louvicourt Goldfields, is at the initial production stage. Of the sixteen properties in the western half that are operating or have operated, all, except the Golden Manitou, which is a base metal mine, and the old Green Stabell from which there was a small production of copper, produce gold. Of the eleven prospective mines in the western half nine have gold. New Bidlamaque has gold and copper and one, East Sullivan, has copper-zinc ore. Since production began in 1927 gold, silver, zinc, copper, and lead having a total value of about $10,000,000 have been produced from the mines of the eastern section of the southern gold belt of western Quebec.

Jan 1, 1954

By Megan Becker, Aubrey Mainza, Indigo Research Laboratories, Jenny Wiese, Gaynor Yorath, Lucy Little

Particle shape characterisation has an important role to play in mineral processing, to clarify effects of shape on rheology, equipment wear rates, comminution, classification, sizing and flotation. However in industry, shape characterisation is not routine, and the most commonly used shape descriptor in the field (circularity/ angularity/ sphericity) is not invariant. This study aims to investigate shape measurements for a fine particulate ore sample measured with different analytical devices. Two Automated Scanning Electron Microscopy devices with Energy Dispersive X-ray Spectrometry (FEI QEMSCAN® and Zeiss Mineralogic®), and a camera based image-sizer using dynamic image analysis (Retsch CAMSIZER® XT) were compared. Each device was used to analyse the shape characteristics of specific particles in both a coarse sample (–212/+150 µm) and a fine sample (-53 µm) of UG2 platinum ore. Circularity and Roundness frequency distributions obtained from the three devices were then compared. For selected individual particles, circularity showed higher variability than roundness, and the sample circularity distributions obtained by the three devices were completely different. It is clear that circularity data from different studies relying on different devices should not be compared on an absolute scale. The shape parameter roundness was found to be a more robust descriptor than circularity, and it can give a stronger indication of a particulate sample’s shape characteristics on an absolute scale. However, there were still significant differences in the roundness measurements obtained by the CAMSIZER XT and the two Auto-SEM devices, which was attributed to the dissimilar mechanisms of image capture.

Jan 1, 2016

By Malcolm Scobie

"This paper reviews the evolution of Canadian surface and underground mining automation, principally relating to: advances in communications, initial development of machine teleoperation from line-of-sight remote control, and islands of automation. The eventual role of teleroboties and minewide robotic mining remains to be resolved. The progress and approaches adopted have tended to vary within each sector of the mining industry. Recent information technology advances have made possible the Digital Mine; in which information associated with all mining processes, however dispersed, would be integrated with support systems using new communications technology. The Digital Mine will provide the information infrastructure to serve as the foundation for minewide automation. This paper concludes by reviewing the issues likely to govern implementation success, relating to: mining process design, machine design, machine intelligence, and mine planning and control.IntroductionSignificant advances have recently been made in underground hardrock mine communications and teleoperation. Subsequent R&D efforts are mainly focussing on control systems for various types of machines. In underground potash mining, the realization of automated continuous mining systems appears to be imminent. Recent advances in surface mine dispatching, machine monitoring and global positioning systems (GPS) have tended to reactivate some of the initial R&D enthusiasm developed in the '70s for surface mine automation. Mines at large are approaching a major milestone: the implementation of comprehensive communications infrastructure which proves to be sufficiently reliable and economical to support the automation of routine mine production, either using teleoperated or autonomous machines. This then should motivate a deeper commitment to real time monitoring and management. The communications advances make possible the Digital Mine; in which information associated with all mining processes, however dispersed, would be integrated with support systems using information engineering. The Digital Mine will provide the information infrastructure to serve as the likely foundation for a wide range of automation scenarios. This paper surveys the status and directions of automation development in both surface and underground Canadian mines, pointing to what are seen to represent key technology development issues."

Jan 1, 1995

By H. D. S. Miller

"This paper introduces a new approach for the design of rib pillars. The approach involves an empirical method for pillar design and a discussion of the pillar stability used for open stope mining methods.The empirical method predicts the degree of stability of rib pillars. Pillar load is estimated using two and three dimensional numerical modelling. Rock strength and the shape effect of pillars are used to account for pillar strength. The method has been calibrated with case histories from Canadian open stope metal mines and is compared with other methods used [or pillar design.INTRODUCTIONThe role of rib pillars in open stope mining is to provide stability to a mining block by limiting rock mass displacements and restricting the exposure of a rock mass in stope backs and stope walls. They also provide flexibility in ore extraction by dividing a stope block into multiple working faces.The use of backfill in open stope mining methods has reduced somewhat the need for optimum pillar design. In contrast to permanent pillar methods, the dimensions do not need to be minimized because the pillars are usually recovered in a later stage of mining. However, the consequences of poor pillar design are often overlooked and can still be severe. A pillar that does not perform its intended role may result in excessive stope or pillar sloughing, difficult and expensive pillar recovery, loss of permanent access and remedial costs such as development rehabilitation, artificial support or low productivity.Pillar design concepts of the past were not developed for open stope mining conditions and generally have not been confirmed for open stoping. The focus of this paper is to introduce an empirical design relationship specifically for open stope pillars. It provides a stable, yielding or failed pillar assessment for a given design."

Jan 1, 1989

By A. C. Hatton

Doped SrCoO3.8 was found to be a promising material for use as a cathode component in intermediate temperature SOFCs. In this work, strontium cobaltite ceramics doped with 10 mol% to 90 mol% samarium were synthesized using the glycine nitrate process in order to study the electrical conductivity and thermal expansion at temperatures of up to 800°C. As-synthesized powders were deagglomerated, pressed and sintered at temperatures ranging from 1100-1250°C. The effect of temperature and composition on electrical conductivity and thermal expansion are presented and discussed.

Jan 1, 2005

By Sadough vanini Ali

The silicon anisotropic wet chemical etching technique is widely employed for fabricating various microelectromechanical system (MEMS) structures for advantages such as simple etching equipment and its capability to fabricate special microstructures. In this paper, we consider a complete theoretical derivation of the analytical solution based on geometrical and kinetic aspects of step flow on any surface and with a mathematical method we derive new equation for calculating the microscopic etch rates of surface atoms for a new range of concentrations and temperatures. Furthermore, a novel equation is presented for the calculation of the microscopic activation energies for some typical surface atoms and a new comparison of activation energies between some atoms is made that divides atoms into three categories. The results demonstrate agreement with the experimental results.

Oct 1, 2011

By Farzad Mohammadi, David Kratochvil, Patrick Littlejohn

"With more rigorous regulations being enacted in the mining industry, a need exists for cost effective and environmentally compliant technologies to remove selenium from mine impacted waters to ultra-low concentrations. Existing selenium treatment methods have high life cycle costs, introduce risks of acute fish toxicity, and produce biological waste residues that represent future liabilities. Furthermore, achieving selenium discharge limits of less than 4 ppb is a challenge for existing technologies. Selen-IX™ is a technology developed by BioteQ that selectively removes selenium from mine impacted waters to less than 1 ppb. The technology is purely physico-chemical and takes advantage of the basic principles of ion exchange and electrochemistry. Unlike conventional electrocoagulation that removes suspended solids and breaks emulsions or oxidizes heavy metals, the electrochemical process employed by Selen-IX™ relies on creating conditions where iron acts as a highly effective reducing reagent transforming selenium from a dissolved species into elemental selenium bound in a solid phase. The iron-selenium by-product of Selen-IX™ is an inorganic, non-hazardous and chemically stable solid. Due to their high iron content, the solids produced by Selen-IX™ are of interest to the steel making industry as a low cost feedstock. This offtake potential can not only reduce the life cycle cost of selenium removal by reducing disposal costs but more importantly, eliminate the risk of future environmental liabilities. In this paper, the basics of Selen-IX™ technology are presented along with results of successful piloting on streams from coal and copper-gold deposits.INTRODUCTIONVarious contaminants are released into mining wastewater during the extraction and processing of metals. One such contaminant is selenium. A naturally occurring element found in rocks and minerals, mining activities accelerate its release into the environment. Selenium in trace quantities is essential to all life forms but at higher concentrations it can be harmful, especially to aquatic life where selenium bioaccumulation can lead to reproductive deficiencies."

Jan 1, 2016

By P. R. A. Andrews

"A sample of flotation feed from Bakertalc Inc., High water, Quebec was subjected to flotation evaluation to improve the recovery of talc. A number of alternative frother/collectors and depressants as well as flotation parameters including pH, conditioning time, frother/collector concentration and pulp density were assessed. In addition, the possibility of using a size coarser than that currently employed for flotation (95% minus 50 um) was investigated.As far as possible, a laboratory duplication of the present circuit arrangement was folio wed so as to minimize the cost of any changes. The best results obtained were a concentrate analyzing 95.96% acid insol for a recovery of 65.98% after four stages of cleaning. With recirculation of cleaner tailings, the recovery would be higher.The possibility of using an alternative method, based on the natural ability of talc to float unaided by a frother/collector, was briefly explored with encouraging results.IntroductionBakertalc lnc ., located in the eastern townships at Highwater, Quebec, Is approximately 140 km east of Montreal near the Vermont, U.S. border. Originally called Baker Mining and Milling Co. Ltd., it has produced pulverized talc products since 1938(1 ), although records show that talc was mined in the area as early as 1871(2). Feed to the mill originally was obtained from local deposits, but since 1952 the van Reet mine near south Bolton, approximately 25 km from Highwater, has been the source of ore .In 1957 a Raymond high -side roller mill was installed which enabled production of a greater range of talc products and, in 1960, new crushing equipment and a dryer were added. Other additions to the mill were the introduction of wet magnetic separation, although this was later discontinued, and flotation to produce high-grade talc concentrates."

Jan 1, 1985

By F. Kapeller, G. Herget

"The need for monitoring the effect of changes in ground stresses due to mining in hard rock has existed for many years. The Mining Research Laboratories of CANMET, EMR have developed a new tool which monitors with high precision the radial deformation in boreholes. The result is the Mining Research Laboratories strain monitoring system (MSMS) which uses the highly stable and very sensitive vibrating wire principle to monitor deformations in relatively large boreholes, e.g. 76 mm to 153 mm diameter.The vibrating wire is strung across a relatively large proving ring and operates at a frequency between 600 to 1800 Hz. The read-out system is based on continuous vibration.The ring is installed with a hydraulic tool and brought into contact with the surrounding rock through precisely machined and guided wedges. The resolution of the system is in the neighbourhood of 4 x 10-4 min/ Hz. The data collection can be carried out with a portable read-out unit and provisions are available for automatic data collection. Stresses may be calculated from strain readings.The system was tested in cooperation with the Centre de recherches minérales at the Niobec Mine in Quebec for the purpose of monitoring the effects of drill drift development and slope mining on surrounding ground stresses.After access was available to the site, 153 mm diameter holes were drilled for the determination of in situ ground stresses. These holes were then used to install the strain monitoring system. The effect of drill drift development and production blasting in stopes C-203-13 and C-203-15 on ground stress distribution could be observed clearly.The horizontal relaxation in the core of a pillar which occurred during mining of adjacent rooms was between 0.082 mm to 0.111 mm. Calculations of stresses from these deformations indicate that the rock material is still in an elastic condition.Roctest of Montreal has obtained a license on the manufacturing and distribution rights. A patent has been registered and CANMET will assist in installation of the MRL strain monitoring system and the interpretation of records."

Jan 1, 1989

By H. Staton, V. Suontaka, E. Sharifi

"Flotation circuits are typically controlled using on-line elemental assays obtained from the slurry lines. In base metal applications, X-ray fluorescence (XRF) analyzers are the most common instruments for elemental analysis of the slurries. Eagle Mine has been utilizing a Courier XRF Analyzer since 2014. Typically, in XRF analysis, the sampling rate is 10-25 minutes which is good enough for manual process control. In 2018, Eagle Mine upgraded the Courier XRF analyzer with the Rapid Measurement module that is based on reflectance spectroscopy. This option reduces the sampling rate to 10-15 seconds, while maintaining the superior accuracy of the XRF analyzer. This paper presents the results from implementation of Rapid Measurement at Eagle Mine.INTRODUCTION Eagle mine is an underground mine producing nickel and copper concentrates. Eagle Mine is owned by Lundin mining and located in the Upper Peninsula of Michigan, USA. The Humboldt Mill, previously an iron ore processing facility, was refurbished in 2014 and is used to process the ore and produce separate nickel and copper concentrates. Approximately 2,000 metric tonnes of ore is milled per day. Ore is processed using a conventional crushing followed by single stage ball mill and flotation. Nickel and copper concentrate are transported to facilities in North America via rail car. A bulk copper-nickel concentrate is produced by separating the copper and nickel minerals from gangue material by flotation. The copper-nickel bulk concentrate is reground, followed by one stage of cleaning to reject further gangue minerals. The bulk cleaner concentrate is then subjected to a final flotation stage where the copper and nickel minerals are separated from one another through the addition of lime. Final concentrate grades are 14% Ni and 2% Cu in the nickel concentrate and 31% Cu and 0.8% Ni in copper concentrate."

Jan 1, 2019

By R. V. Hopper, M. E. Wilson, L. S. Trenholme

"The Company known as Rouyn Merger Mines, Limited, was formed in 1943 to take over the ownership of claims in Rouyn and Joannes townships formerly held by East Rouyn Mines, Limited, O'Neil Thompson Mines, Limited, and the Hosking-Cockeram Prospecting Syndicate. The NorandaSenneterre branch of the Canadian National railway passes in an approximately east-west direction through almost the entire length of the property. Since 1937, sixty-three diamond drill holes have been drilled from the surface to cross faults on the contact of the Timiskaming sediments with the Abitibi ( Keewatin) volcanics, along which ore has been found to occur. Late in 1945, the sinking of a 3-compartment inclined shaft in the andesite agglomerate beneath the ore zone was commenced. On January 17th, 1947, this shaft had a depth of 944 feet; cross-cuts have been driven north-northwest from the shaft at 150-foot intervals from depths of 200 to 800 feet on the shaft (Fig. 2).GEOLOGYThe western or East Rouyn part of the Rouyn Merger property in which ore is being mined adjoins the area owned by McWatters Gold Mines, Limited, on the east and is underlain by the eastern continuation of the McWatters formations. As at the McWatters, the rocks belong structurally to three areas: (1) the territory north of the Cadillac-Bouzan Lake fault, occupied almost wholly by Abitibi ( Keewatin) volcanics; (2) the area along the south boundary of the property, underlain by Timiskaming conglomerate and greywacke; and (3) the synclinal belt of McWatters volcanics and sediments between areas 1 and 2.1Bouzan fault of Hawley."

Jan 1, 1954

By G. D. Garland

The influence of natural electric currents, induced in the earth by changes in the earth's magnetic field, on the electric logging of boreholes has not always been recognized. Measurements made with fixed electrodes of changes in the vertical potential gradient in a hole near Calmar, Alberta, have indicated the effect of earth currents related to magnetic disturbances. It is found that appreciable errors in self-potential logging could arise during periods of magnetic storms, but the precise pat-tern of disturbance in any area seems to depend on the local structural conditions. As the amplitude of the natural earth currents increases toward the auroral zone, it is suggested that periods of magnetic disturbance be avoided, if possible, when electric logs are taken in the northern part of the western sedimentary basin. NATURAL electrical currents flow continuously near the surface of the earth, apparently as a result of electromagnetic induction

Jan 1, 1962

By O. Lashkari

Swirled Enthalpy Equilibration Device (SEED) is a new patented Slurry-on-Demand, SoD, processing route. The semi-solid slug preparation is carried out by off-center swirling of aluminum melt in a metallic mould. As part of the current research program on the semi¬solid processing of aluminum alloys, the morphological evolution of 356 aluminum foundry alloy microstructure is reported here. Semi-solid slugs were prepared using two different pouring temperatures of 645°C and 695°C respectively. Morphological evolution of the semi-solid microstructure was characterized using image analysis through measuring of primary a-Al particle size, number density, aspect ratio and sphericity. The possible relationships between microstructural features and process parameters were also investigated. The current report covers the effect of pouring temperature on the morphology of primary a-Al dendrites and attempts are made to explain the differences between the predicted percentage primary a-Al phase and those of the actual values in the as-cast slugs.

Jan 1, 2004

By P. R. G. Brandão, E. E. Ferreira

The presence of metallic cations in solution will affect the aggregation or dispersion of the fine hematite particles, depending on the type of cation adsorption: either specific or non specific adsorption. In this work, the zeta potential measurements were carried out on a sample of pure hematite as a function of pH and metallic cations concentration (Ca2, Mg2+, Mn2+, K+, Na+ and Al3+). The objective of these studies was to clarify the effect of these metallic cations on the surface chemical properties of pure hematite. The cations K+ and Na+ adsorbed as non-specific species and caused only the reduction on the values of zeta potential (in terms of absolute value) over the entire range of pH values tested. For the Al3+ cation, in the acidic pH range it adsorbed as a specific species and increased the zeta potential values. The cations Ca2+, Mg2+ and Mn2+, adsorbed as a non specific species at pH levels less than 6.0 and caused the reduction of zeta potential due to the compression of the electrical double layer. However, for pH values greater than 6.0, these cations adsorbed as a specific species causing the zeta potential to increase and became more positive as the pH value increased (alkaline). This effect could be due to the adsorption of some hidroxy complex species of these cations, which contributed to the positive charge. The effect of metallic cations (Ca2+, Mg2+ and Al3+ concentration, at pH 4.0, 7.0 and 10, showed the following results: a) at pH 4.0, increasing the concentrations of Ca2+ and Mg2+ resulted in on a small reduction in the value of the zeta potential. At this pH, increasing the concentration of A131 cations caused the zeta potential to increase due to specific adsorption of a negatively charged Al3+ hydroxy complex b) at pH 7 and 10, increasing the concentrations of Ca2+ and Mg2+ caused the zeta potential to change its charge from negative to positive.

Jan 1, 2004

By John Rowson, Caitlin Brown, Kebbi Hughes, Joseph Esslifie-Dughan

The McClean Lake mill in northern Saskatchewan, Canada, is operated by Orano Canada Inc. and has been in production for the last 20 years. The tailings preparation process at the mill has been designed with decommissioning in mind, to produce tailings that are geochemically stable over the long-term within the site’s tailings management facility. Twenty years of study have contributed to a detailed understanding of geochemical and geotechnical properties of the McClean Lake tailings. Validation of the tailings properties has occurred through in-situ sampling campaigns conducted initially every year, and later every five years. Each sampling campaign has applied the same rigorous sampling procedure to provide data with useful correlations year over year. Each campaign result compares elements such as the inherent variability of the tailings, consolidation of the tailings and variations in the tailings placement methods. We will discuss lessons learned from seven sampling campaigns over 20 years and present data to show the reliable tracking of geochemical evolution of the in-situ tailings over time; providing opportunities for continuous improvements.

Jan 1, 2020