Search Documents

By D. M. Doyle

"A study of the various components contributing to energy costs and their relationships to generally trended operating data, such as tonnage, operating costs, etc. over progressively shorter time periods provides information for an energy audit. A study of annual data gives some insight into the importance of various energy components. As the time frame of the study 11rogresses through monthly, daily and finally, into quarter hourly data, the variations become more evident and most important, strategies develop to minimize energy costs. The results of an audit conducted during the summer of 1978 at Wesfrob Mines are reported to illustrate this important phase, prerequisite to a meaningful energy cost avoidance program.The balance of the paper deals with the energy conservation program at Falconbridge Nickel Mines Sudbury Operations, the material and control equipment, the commitment, the new energy accounting practices and lastly, the policies. Examples of successful energy conservation endeavors include automatic peal electrical load control, waste heat recovery from mine air and compressor cooling water, energy reductions resulting from lower building temperatures and curtailmen: of idling loads. The use of pulse meters to measure the flow of gas, steam, compressed air and electrical energy, with their signals interfaced to process computers, allows monthly, daily and if necessary, immediate reporting of energy and energy per unit of production information. The program so reported at Falconbridge’s Sudbury Operations is credited with an annual cost avoidance of .9 million dollars in a 14.0 million dollar annual energy account."

Jan 1, 1979

By K. Biswas, F. C. Felipe

Paste backfill, because of its colloidal or water-holding properties, does not produce run-off water when placed underground. Paste backfill is generally, prepared from relatively low water content, full mill tailings with a certain proportion of ultra-fine particles and mixed with cement, thus producing early and better strength. Mill plant discharge tailings and other materials available at or near the mine site such as sand, aggregates or waste rock are used as blending materials in the mix design. This study investigates the influence of the above-mentioned blending materials on the mechanical characteristics of paste backfill, as well as the grading, shape, specific surface area, mineralogy and workability of the different mix design.

Jan 1, 2000

By Kerry Gee, Gary Colgan, James Fricke

Introduction Elevated zinc concentrations are observed in groundwater within alluvium adjacent to Silver Creek east of Park City, Utah. The study area is located in a small valley one and one-half miles northeast of Park City, Utah in Summit County, Utah (Figure 1). Although surface water concentrations in Silver Creek are typically less than 1 mg/l, groundwater concentrations have been measured as high as 85 mg/l in a near neutral pH environment. The elevated zinc concentrations in groundwater result from several factors including: (1) dissolution of zinc from tailings exposed at the surface and within the alluvium, (2) oxidizing conditions created by surface/ground-water exchange, and (3) ideal geochemical conditions for the dissolution of zinc-containing minerals. These ideal conditions include readily soluble minerals, available anions for complexation, and lack of available surface adsorption sites.

Jan 1, 2005

A study was made of zircon powders bonded with phosphoric acid or aluminium orthophosphate. The influence of strength of solution of the phosphatic binders on the modulus of rupture over a temperature range was investigated. Physical properties of three grades of zircon powder bonded with phosphatic binders were studied at various temperatures. Examination of x-ray diffraction data indicated that phosphates ofzirconia are preferentially formed to phosphates of silica. However, zircon in the presence of excess phosphoric acid also forms phosphates of silica upon heating.Resistance to attack by slags from blast and open hearth furnaces was determined on phosphate-bonded zircon mortars in a cup test with industrially made ladle bricks. Zircon powders bonded with phosphates proved to have high P.C.E. values. The first satisfactory results of a plant trial with phosphate-bonded zircon mortar, used in a steel ladle, are now being assessed in larger scale industrial tests prior to accepting the mortar as a steel plant refractory.

Jan 1, 1972

By K. Whiting, R. Huffsmith, R. Olsen, D. Adams

Long-term closure alternative selection for heap leach pad effluent is a daunting task. Passive water treatment, if designed with enough long-term capacity, can minimize long term O&M while meeting water quality objectives. Leach pad effluent from a 30-acre leach pad at Basin Creek Mine, Basin, Montana was targeted for long-term water treatment using a passive water treatment system. The objectives and results of design and construction are: 1. Design a long-term passive system utilizing existing infrastructure. 2. Construct a field scale pilot test at the mine site.

Jan 1, 2002

By J. J. Dekker

Controlling noise has proven difficult in mining, and noise-induced hearing loss (NIHL) remains common. In 2008, a South African Mine Health and Safety Council study focused on small- to medium-sized mines in relation to the milestones set by the industry to prevent NIHL. An evaluation of the compliance of ten diamond, sand, aggregate and Ready mix concrete mines and production sites with standards, legislation and best practice guidelines relating to NIHL prevention was conducted, using a noise compliance audit tool. The findings indicated that all mines surveyed had poor compliance with the international standards, compliance with International Standards Organization standards being the poorest. There was a clear distinction between the small and the medium-sized mines in their compliance with local standards and legislation (ranging from 14 per cent to 66 per cent). The areas of best compliance were audiology and medical examinations. The lower-than-expected compliance was largely attributable to shortcomings in hearing conservation programmes for occupational noise. Initiation of remedial practices in the small- to medium-scale mining sector to facilitate improvements in NIHL prevention and compliance with standards and legislation is recommended. Keywords Hearing conservation, small-to-medium mines.

Jan 1, 2011

By Jean A. Bastien

Cette présentation décrit les étapes de développement et l?exploitation souterraine au puits Penna chez Agnico-Eagle division Laronde. Les sujets suivants sont touchés : le fonçage du puits, le développement des niveaux, la méthode d?exploitation, la manutention de la roche brisée, le méthode de remblayage et la ventilation. En résumé : le fonçage du puits s?est fait sur 2,240 mètres de novembre 1995 à mars 2000. Le développement des niveaux a débuté en octobre 1998. Les opérations de minage ont débutés en août 99 dans le premier horizon situé au dessus du niveau 122. Les chantiers sont exploités par longs-trous d?environ 25 mètres de long avec un diamètre de 10 cm. Les accès à la zone minéralisée sont transverses. Le minerai est soutiré des chantiers et acheminé au passe-minerai a l?aide de chargeuses navettes. Par la suite, le minerai passe sur un marteau, est concassé et transporté sur un convoyeur, jusqu?au silo de 4,500 tonnes au-dessus de la station de chargement automatisée du niveau 152 d?ou les skips sont alimentés. Le remblai en pâte est envoyé de la surface par des trous ayant un revêtement d?acier. Le diamètre intérieur est de 15 cm. Le réseau de ventilation est principalement alimentée par des ventilateurs de surface (système aspirant et souflant) conçus pour acheminer sous-terre un maximum de 640 mètres cubes par minutes (1,350,000 pcm).

May 1, 2001

By Deni Côte, Marcel Vallée

"The Guide to the Evaluation of Gold Deposits reviews the successive evaluation steps in the domains of geology, engineering, and economics. The Guide analyzes, in a systemic perspective, the sequence of exploration, development, and evaluation work required to bring a mineral deposit to production. The aim is to identify the metal/mineralization losses and ore dilution that each work step contributes to the evaluation and mining process. The procedure allows one to maximize the income and profits of a mining operation, and to reduce the risks of financial losses tied to investment decisions in the mining sector. For greater efficiency, the criteria of reserve estimation and classification should be integrated with the evaluation steps and methods. At earlier stages of deposit development, when quantitative knowledge is available mainly on the geological axis, the term ""delimited mineral deposit"" should be used. The term ""reserve"" should be used only in an operating mine or in a mining project, when information in the geological, engineering, and economic domains is adequate to ensure technical and financial feasibility. ""Reserves"" are by definition ""mining reserves"". Each category of proven/probable reserves and measured/indicated deposits should be subdivided into two classes to express better the many steps of mineral valuation. The category of ""possible reserves"" shall be replaced by that of ""inferred mineralization"". This system, derived from the Australasian Code, can easily be integrated into current practices of the exploration and mining industry within a short timeframe. The proposal to develop the use of the margins of error of the estimates at a confidence level of90% should be viewed in a longer timeframe. Establishing the precision of the mineral inventories and distinguishing between categories and classes by means of the margin of error will require more work and a longer break-in period.SOMMAIRELe ""Guide d’évaluation des gisements d'or"" analyse, dans une approche systémique, les travaux d'évaluation et de mise en valeur des gisements minéraux dans l'axe de la géologie, dans l'axée l'ingénierie et dans I ‘axe de l'économique. L’objectif est d'identifier la contribution aux pertes de métal et à la dilution du minerai des diverses étapes de l'évaluation et de l'exploitation du gisement. Ceci aid erra à maximiser les revenus et les profits, et ainsi, à réduire les risques départe financière que comportent les décisions d'investissements dans le secteur minier. Pour atteindre ces objectifs, iI est essentiel de relier les critères d'inventorie et de classification des réserves aux méthodes d'évaluation des gisements. Aux stades antérieurs du développement minéral, lorsque les connaissances quantitatives ne s'étendent qu’à l'axe géologique, le terme ""gisement délimite"" sera utilisé. Le terme ""réserve"" ne sera utilisé que dans une mine en exploitation au dans un projet minier, lorsque l'information dans les axes de la géologie, de l'ingénierie et de l'économique sera appropriée pour en garantir la faisabilité technique et économique. Chaque catégories des réserves, prouvée et probable sera subdivisée en deux classes pour mieux qualifier les niveaux d'évaluation du projet. La catégorie actuelle des réserves possibles sera remplacée par celle des ""minéralisations inférées"". Plusieurs essais démontrent que le système propose, qui s'inspire du Code australasien, peut facilement et rapidement s'intégrer dans les pratiques de l'industrie. II pourrait également contribuer à une standardisation des méthodes et des nomenclatures à l'échelle internationale. La proposition d'utiliser les marges d'erreur des estimes au niveau de confiance de90%pour caractériser les estimations se situe dans une plus longue perspective. Cette application demandera des développement méthodologiques additionnels ainsi qu'une période de rodage."

Jan 1, 1992

By Alain Blanchier, Gilles Gomez

Neighborhood pressure on quarries has become urgent to deal with quarry managers and operators must apply the most recent technologies and communicate it for long shelf life time exploitation, the quarry in which the work is located in urban or suburban environments needs to take into account blasting rules as well as site environment. The main problems to be addressed are:

Jan 1, 2009

By Russel Delmar

Construction of Ontario Power Generation?s 12.8-m diameter, 10.4-km long water diversion tunnel in Niagara Falls, Ontario, is underway. The tunnel is being excavated by means of a 14.44-m diameter open gripper Tunnel Boring Machine. The tunnel lining is constructed as a two-pass system with the initial lining consisting of rock bolts, mesh, steel channels or ribs, and shotcrete, and the final lining consisting of pre-stressed cast-in-place concrete with a waterproof membrane. This paper describes salient design and construction aspects as follows: ? Regional and Site Geology ? Tunnel Layout and Design ? TBM Tunnelling and Cast-in-place Concrete Lining Construction

Jan 1, 2008

By G. van Aswegen

Large structures in mines (faults, dykes, pillars, abutments) fail when the load exceeds the strength. If the loading system stiffness (LSS, also referred to as the ‘local mine stiffness’) is lower than the stiffness of the structure the failure will be unstable. The greater the difference between these stiffnesses, the greater the energy release during unstable failure. A method has been formulated by which the LSS is established through cost-effective numerical modelling while insight into the structure stiffness (source stiffness - SS) is provided by apparent stiffness, a parameter based on the empirical relation between seismic moment and radiated seismic energy of small seismic events from the area/volume of interest. By plotting LSS vs SS a ‘stiffness diagram’ is constructed that is useful for seismic hazard ranking of different structures. A comparative back-analysis of the Dagbreek fault in Welkom, South Africa, (source of the 1990 Matjhabeng earthquake) and two other nearby faults confirm the applicability of the method. An extension of the method, where ‘hazard magnitude’ is used as a measure of the LSS, allows a ‘stiffness diagram’ to be constructed using seismic data only. Les larges structures dans les exploitations minières (failles, dikes, piliers, culées) s’écroulent lorsque la charge dépasse la résistance. Si la raideur du système de chargement (LSS, aussi appelé la « raideur de la mine locale ») est plus basse que la raideur de la structure, l’éboulement sera instable. Plus la différence est grande entre ces deux raideurs, plus l’énergie dégagée pendant l’éboulement instable est grande. Une méthode a été formulée selon laquelle le LSS est établi par modélisation numérique rentable, tandis que la raideur de la structure (SS – raideur de la source) est établie par la raideur apparente, un paramètre basé sur la relation empirique entre le moment sismique et l’énergie sismique radiée de petits moments sismiques dans l’aire/volume en question. On trace le « diagramme de raideur » en relevant les deux mesures (LSS et SS), ce qui est utile pour classer les risques sismiques de structures différentes. On vérifie l’applicabilité de la méthode en comparant la faille de Welkom, Afrique du Sud (foyer du séisme de Matjhabeng en 1990) avec deux autres failles proches. Une extension de cette méthode, dans laquelle on utilise la « magnitude du risque » comme mesure du LSS, permet de construire le « diagramme de raideur » avec des données sismiques seulement. Große Strukturen in den Gruben (Verwerfungen, Dämme, Pfeiler, Auflager) scheitern, wenn die Last die Stärke übersteigt. Wenn die Steifheit des Ladesystems (LSS, auch bezeichnet als `lokale Grubensteifheit’) niedriger ist als die Steifheit der Struktur wird der Bruch instabil. Je grösser der Unterschied zwischen diesen Steifheiten, desto grösser die Energiefreigabe während des instabilen Bruches. Es wurde eine Methode formuliert, durch die das LSS durch eine kosteneffektive numerisches Modell erstellt wird, während ein Einblick von der offensichtlichen Steifheit in die Struktursteifheit (Quellensteifheit - SS) gegeben ist, ein Parameter der auf der emipirischen Relation zwischen seismischem Moment und ausgestrahlter seismischer Energie von kleinen seismischen Ereignissen vom Interessens-/Volumenbereich basiert. Durch das Kartograpahieren der LSS in Bezug auf die SS wird ein `Steifheitsdiagramm ' konstruiert, welches für seismische Gefahrklassifizierung der unterschiedlichen Strukturen nützlich ist. Eine vergleichende Postanalyse der Dagbreek Verwerfung in Welkom, Südafrika, (Zentrum des Matjhabeng Erdbebens 1990) und in zwei anderen nahe gelegenen Verwerfungen bestätigen die Anwendbarkeit der Methode. Eine Verlängerung der Methode, in der die `Gefahrengröße' als Maß für das LSS verwendet wird, gestattet, daß ein `Steifheitsdiagramm' konstruiert wird, welches nur seismische Daten verwendet.

Jan 1, 2003

LARGE-SCALE production of zirconium by the Northwest Electrodevelopment Laboratory of the Bureau of Mines at Albany, Oreg., is an anomaly that justifies some explanation. The reduction of titanium tetrachloride with magnesium in an inert atmosphere, as perfected by Dr. W. J. Kroll before 1940, aroused renewed interest in zirconium, and in 1945 development work on this metal was initiated at Albany under Dr. Kroll's technical direction. Preliminary results were promising, and in February 1947 a pilot plant with a weekly capacity of 60 pounds of zirconium-metal sponge was put in operation. Shortly thereafter the Oak Ridge National Laboratory of the Atomic Energy Commission requested production of 1 ton of zirconium-metal sheet, with the provision that it have a low hafnium content. The Bureau of Mines was furnished with a. supply of Brazilian baddeleyite ore, containing less than 1 percent hafnium with respect to zirconium, from which was made about. 2,700 pounds of relatively low hafnium zirconium sheet of 0.080-inch thickness for test purposes. This was accomplished by melting zirconium sponge in a graphite crucible, hot-rolling the ingot in an iron sheath, and finishing by cold rolling. Concomitantly the Oak Ridge Laboratory developed a method for separating hafnium from zirconium; and, in cooperation with the Atomic Energy Commission and the Bureau of Ships of the Department of the Navy, a, larger pilot plant was erected to produce zirconium from very low hafnium zirconium tetrachloride furnished by the Commission. Pilot-plant work on producing zirconium tetrachloride from zircon sand and baddeleyite was discontinued. Production of zirconium sponge in the larger pilot plant of 500 pounds per week capacity was begun in June 1949.

Jan 1, 1956

By D. Berkley

"The competitive pressure, the increasing energy costs and the environmental regulations impose substantial challenges to the definition of power plants serving industrial facilities. Primary mining and metallurgical facilities have even greater challenges because they are often located remotely, where the fuel supply can be a problem. The absence of a power grid imposes challenges on the reliability and quality of the electrical energy supply. In addition, the facilities usually require thermal energy too, not only electricity.This paper outlines these types of issues that have to be considered when defining a cogeneration plant integrated with a remotely located industrial facility. It is addressed to the “users” of cogeneration facilities rather than to “generators.” The focus is on analyzing various site-specific design considerations to prescreen the feasible cogeneration alternatives and minimize the number of options to be analyzed from the economics viewpoint. This approach could substantially reduce the engineering effort and schedule during the feasibility phase of the project.The front-end of the paper provides a basic understanding of cogeneration plants of various types to establish a common language. Subsequently, the paper outlines and analyzes specific issues that could be of help in the definition of cogeneration installations for remotely located industrial facilities, with a focus on mining and primary metallurgical plants"

Jan 1, 2003

By Madan Kumar Annam, Hari Krishna Y

"Basement construction is one of the challenging geotechnical concerns in the urban environment. Several types of retention systems are practiced to support the earth which is suitable for restricted access, rapid mobilization, fast excavation and cost-effective designs. A thorough understanding of geotechnical engineering as well as the structural mechanics is important for the earth retention systems. This paper discusses a project with various types of foundation solutions including monitoring of deflections during excavation stage of a retention system.A multi storeyed residential building (3B+Stilt+18F) in Chennai having structure foot print area of 1500 m2 has to be constructed on large diameter pile foundations and also to support the proposed basement excavation. Ground water table was encountered at about 6m below the existing ground level (EGL). In order to support heavy structural loads, large diameter bored cast-in-situ piles were chosen and installed. Further, complete retention system was economically designed and built, which includes installation of Contiguous Bored Piles (CBP) in combination of vertical grout columns behind CBP wall to seal the gap between the CB Piles, installation of inclined ground anchors, construction of capping beam, stressing and locking of installed ground anchors. A detailed monitoring program was in place and continuous monitoring of wall deflections is being measured at the time of publishing this paper. This paper describes the design and construction aspects adopted for foundation and retention system including the monitoring results during excavation stage of the project.INTRODUCTIONIn general, stage wise open excavation will be opted for basement construction where plenty of space is available. Due to urbanization and restricted space, open excavation became a difficult task nowadays. To overcome this problem, suitable retention system need to be selected to retain the soil mass. Selection of suitable retention system for multi-level basement excavation is a great challenge in geotechnical industry, especially when the proposed site is located within the minimum set back distance from the existing structures. This in turn calls for the advanced and innovative methods of retention system.Several earth retention systems such as Diaphragm Walls, Secant Pile Walls, CBP system, Soldier Pile Walls, Sheet Piles, Deep Soil Mixing (block walls) etc. with or without inclined ground anchors are being practiced worldwide. Considering the advantages and disadvantages of the available retention systems in practice locally and keeping in view of present site conditions, the developer has chosen CBP system with inclined ground anchors so that all foundation related works of the project will be handled in a single package. The main advantage of such packaged solution will ease the coordination between design consultants and foundation contractor resulting in faster construction of foundation works which in turn reflect savings in time and cost."

Jan 1, 2015

By Cathy Aimone-Martin, Caitlin Woznick, Brent Meins

This study is a continuation of previous work in which the responses of tall structures to close-in construction blasting at two rock excavation sites are evaluated. A total of eight buildings were instrumented to calculate blast-induced wall strains. Of these structures, five high-rise buildings measuring 166 ft (51 m) to 294 ft (90 m) in height (15 to 24 stories), were included for this study and compared with the results of previous studies that included one to three story residential structures and mid-rise structures (four to six stories). All five structures were built between 1908 and 1940 with interior walls comprising aged plaster. Three of the structures are designated Landmark, subject to a 0.5 in/s (12.7 mm/s) regulated peak particle velocity (PPV) limit. The regulated PPV limit for the two other structures was 2.0 in/s (50.8 mm/s). To date, a total of 450 close-in construction blasts have taken place over six months at the two adjacent projects, blasting three to six times per day at each site. Seismograph instrumentation included tri-axial geophones in the ground and bi-axial geophones (horizontal components only) mounted on structure exteriors at the corners closest to blasting. Peak global wall tensile strains were calculated from time-correlated differential structure displacements in two horizontal directions as measured by upper and lower geophones mounted near the roof and at street levels. Wall strains were correlated with ground excitations to establish a stiffness factor for each structure defined as the upper bound linear regression slope for strain as a function of ground displacement. In addition, a structure-specific regression best-fit function was established to relate horizontal components of displacement to velocity. These two functions were used to determine the maximum ground motion velocity for a desired limit placed on wall strain. A 25 ?-strain limit was suggested for both projects to protect interior plaster walls. To date, global wall strains have not exceeded 0.53 ?-strains (or 47 times the project limit) for peak particle velocities up to 3.49 in/s (88.6 mm/s). This demonstrates the low strain response of tall structures to ground velocities well above regulated limits. The stiffness factor computed for the most flexible high-rise building was 688 in-1 (17475 mm-1). In comparison, stiffness factors for the most flexible residential and mid-rise structures previously studied were 8651 in-1 (219735 mm-1) and 4387 in-1 (111430 mm-1), respectively. Based on a large number of measurements made at these study structures, the maximum horizontal ground velocity needed to achieve 25 ?-strains in walls ranged from 36 in/s (914 mm/s) to 192 in/s (4877 mm/s) because of the high stiffness of these buildings. Such high amplitudes of ground vibrations can never be safely achieved during close-in blasting in urban environments. These excessive values stand to show how unfounded the current limits of 0.5 in/s (12.7 mm/s) and 2.0 in/s (50.8 mm/s) are when applied to massive, tall structures. This study demonstrated that upper structure motions are highly attenuated from the lower (street-level) motions because of the long travel distances up the buildings. High-rise structures are far stiffer than mid-rise and residential structures and can withstand ground vibration amplitudes far greater than the currently enforced blasting limits in New York City.

Jan 1, 2015

The mineralogy of nickel slags from the flash smelter of Western Mining Corporation Ltd. at Kalgoorlie was studied. Residual magnesium silicates in the sulphide concentrates raise the melting point of the slag and result in the formation of magnesium-rich olivines. Addition of lime lowered the melting point, and, in slowly cooled slags, resulted in the formation of a pyroxene.Magnetite and sulphides were also present in all slags.The converter slags contained an olivine near fayalite in composition, together with wiistite, magnetite, and a little sulphide.Accretions from the hearth of the flash furnace were largely composed of magnetite with subsidiary olivine similar in composition to those of the flash furnace slags.Wall deposits, however, were largely composed of nickel ferrite and nickel-iron olivines.

Jan 1, 1976

By Mark Colwell, Christopher Mark

This paper summarises the results of a research project whose goal was to provide the Australian coal industry with a rib support design methodology and software tool that could be utilised by suitably qualified colliery staff. The project was primarily funded by Australian Coal Association Research Program (ACARP) and further supported by several Australian longwall operations. The outcome of the project is a design methodology and software tool called, Analysis and Design of Rib Support (ADRS). ADRS is an empirical technique, which recognises that several geotechnical and design factors affect ribline performance and in addition that operational and safety issues essentially dictate the level of performance required. Therefore, the design recommendations associated with ADRS are specific to the Australian coal industry; however the procedure(s) for data collection and analysis could be applied to other countries' 'underground coal industries. Case history data were compiled from 34 longwall and two bord and pillar operations resulting in 204 case histories with each case history data set being defined by approximately 130 individual data fields. In addition monitoring (incorporating stress cells and extensometers) was undertaken at 10 collieries to assess and quantify the effectiveness of different rib support patterns and hardware on rib performance. The monitoring sites allowed for an improved understanding of the mechanisms of rib failure and degradation in terms of its interaction with the installed support and at the various stages of the mining cycle. The design methodology deals with both mains development and gateroad development specific to Australian longwall mines. This paper focuses on longwall gateroads subjected to abutment loading and in particular the travel road which becomes the tailgate of the subsequent panel. The statistical analyses associated with these cases suggested that the level of rib support should be based primarily on the development height and the pillar stress level. The ADRS software guides users through the design process, allowing them to develop rib support plans based on sound science and a broad base of in-mine experience To the best of the authors’ knowledge ADRS is the first systematic rib support design technique to be developed for any country’s underground coal industry. The development and use of empirical models in mining have substantially contributed to improving safety and productivity. ADRS further demonstrates that empirical techniques are particularly relevant and beneficial in dealing with the complexities of geotechnical design associated with underground coal mining.

Jan 6, 2008

By M. K. G. Whateley, W. Hatton

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 20pp., 31 refs. Estimates of coal tonnage on UK open cast mining sites often vary from the recoverable tonnage. This is because the estimates depend on the geological variability of the coal measures. Geological parameters, such as thickness, quality and disturbance of the seam, have a direct control upon this variance. Risk analysis techniques have been applied using commercially available software to combine each parameter's variability into a cumulative variance, resulting in a tonnage distribution. Sensitivity modelling has also been used to identify the geological parameters which have the largest influence on the variance of the simulated tonnage distribution. An understanding of the relationship between the tonnage and geological variability has helped to focus exploration more efficiently. A cost to risk relationship can now be monitored, helping management to avoid negative consequences on site

Aug 1, 1995

By T. Ramamurthy

ABSTRACT : Rock mass classifications RMR, Q and GSI do not suggest decreasing modulus ratio with the decrease in the quality of rock. These have been linked to joint factor, Jf , for better prediction. An engineering classification is suggested based on strength and modulus applicable to both intact and jointed rocks. ZUSAMMENFASSUNG : Fels Masse Klassifizierungen RMR, schlägt Q und GSI daß das Abnehmen von modulus Verhältnis mit der Abnahme in der Qualität des Felsen nicht vor. Diese sind zu gemeinschaftlichem Faktor, Jf, für bessere Voraussage verknüpft worden. Eine technische Klassifizierung wird auf der Basis auf Kraft und modulus vorgeschlagen die zutreffend sind zu beiden unversehrten und jointed Felsen. RESUME: RMR de classifications de masse de Rocher, Q et GSI ne suggèrent pas la proportion de modulus décroissante avec la diminution dans la qualité de rocher. Ceux-ci ont été reliés au facteur de jointure, Jf, pour mieux la prédiction. Une classification construisant est suggérée basé sur la force et modulus applicables intacts et les rochers de jointed.

Jan 1, 2003

By Maurizio Siepi, Stefano Trevisani, Pagliaccim Federico, Daniele Vanni

"Abstract: The paper describes a large innovative project completed in 2012-20123 by Trevi Group, to develop equipment capable to install ultra-deep diaphragm wall. The project highlights the capacity of SOILMEC to design and build a new hydromill able to reach an unprecedented depth of 250 m, including new devices for monitoring and correct the verticality. The entire project can take advantage of the long and solid experience matured by Trevi and Rodio (now part of Trevi Group), developing in house or, else, select the elements necessary for a high quality product in the ground.The paper describes the results of different systems used to monitor and control the verticality and the twist of panel during excavation, together with the method used to pour concrete. Finally, the results of verification coring and lab tests on concrete samples recovered at various depths are discussed. The test field has been supervised by representatives of three of the major Italian Universities, and lasts almost one year from August 2012 to June 2013.The verification holes made use of an innovative combination of directional drilling and coring, to check the quality of the plastic concrete for the full length of the panel. The data confirmed that the test panel has high quality concrete, meeting or exceeding to the prefixed requirements.With this test, super-deep cut-off walls reaching depths of 250 m have become a reality. This would change the perspectives of dam engineering both for existing dams rehabilitation and for new dams design and construction. With the execution of this test panel, the technology of milled concrete cutoffs has made a ”quantum leap”, pushing the limit of practicable dams."

Jan 1, 2014