Search Documents

By Jason Herron, Joseph Brown

The common couplings for joining sections of helical piles with an outside diameter of 6.625 inches and 8.625 inches are square on square, flange to flange, external pipe sleeve, internal pipe sleeve, and welded joint. Each coupling type has advantages and disadvantages in efficiency, capacity, installation, and economics of the installed pile. All these coupling types have been used in the helical pile market in North America for various applications and designs. Many of these applications require on-site testing, but test records are not typically shared with the helical pile industry. Due to the lack of information available for square on square and flange to flange couplings, testing was done to compare the efficiency of installation, load to deflection response, and torque to capacity ratios of external pipe sleeve, square on square, and flange to flange couplings. Field installations and tension tests were performed in non-cohesive (sand type) soil near Caseyville, IL and in cohesive (clay type) soil in Centralia, MO. The data collected during these tests included rotations per foot during installation, installation torque, applied pressure, and deflection. The results of this testing are analyzed and discussed within this paper. The results indicate that the square to square coupling is the most efficient of the designs tested, but this conclusion cannot be fully justified without further testing due to the variability in the data gathered and the small number of piles tested. INTRODUCTION A helical pile is typically assumed to be a medium-displacement pile when its outside diameter is between 4.5 inches and 8 inches and a high-displacement pile when its outside diameter is greater than 8 inches. A helical pile designer has multiple options when selecting a coupling type for medium- to high-displacement helical piles. Each type of coupling has advantages and disadvantages and must be analyzed on the bases of efficiency, capacity, installation, and economics of a project. Typical couplings that are chosen by designers include square on square, flange to flange, external pipe sleeve, internal pipe sleeve, and welded joint. A helical pile must transfer axial, lateral, bending moment, and torsional loads, and the coupling must be designed to effectively and efficiently transfer each type of load. During the installation of a helical pile, the rate of penetration and the disturbance of soil layers play a critical role in the efficiency and torque to capacity ratio (Kt) of the pile. It is common for a coupling to protrude beyond the outside diameter of the pipe section being used. This is necessary for the function of certain coupling types and can facilitate the connection of couplings. However, it causes increased soil disturbance and reduce the rate of penetration due to soil bearing against the protruding portion of the coupling. A helical pile designer typically will work to minimize the coupling protrusion and create a pile with optimal installation efficiency but may choose a design with lower installation efficiency if it offers sufficient economic advantage.

Jan 1, 2019

By Michael G. Batten, Brian D. Keaney

]The Virginia Department of Transportation (VDOT) and the harbors on the James River routinely use precast concrete piles founded in the Yorktown formation to support bridges and other coastal structures. However, axial pile resistances for large diameter piles in this area have been historically overestimated on past projects. This may be due to a common assumption that very large unit end bearing resistance will be developed for a large diameter displacement pile that is driven a significant depth. This assumption is integrated in the Nordlund (1963; 1979) method which is commonly used to estimate axial pile resistance for bridge foundations. A static and dynamic pile load testing program was implemented as part of the Hampton Roads Bridge and Tunnel Expansion project in Norfolk, VA in the James River. A primary objective of this program was to calibrate an axial resistance calculation method against the measured load test results. A method developed by Eslami and Fellenius (1997) that uses CPTu data directly was effective at calibrating to the measured load test results, and allowed for clearer interpretation of the unit resistance values than indirect, semi-empirical methods that require interpretation of soil friction angle and undrained shear strength.

Sep 8, 2021

By Richard E. Sylwester

Evaluating surface and subsurface conditions for marine foundations (bridges, causeways, terminals, etc.) is often done with a limited amount of data. Subsurface information for these projects is primarily acquired using traditional methods, such as boreholes, test pits or divers, which tend to be expensive and limited in the area of coverage. A number of geophysical methods, including precision bathymetry, sidescan sonar, and seismic reflection or subbottom profiling are extremely cost-effective and obtain significantly more data than can be acquired using traditional intrusive methods. These geophysical methods provide detailed surface images and continuous profiles of the subsurface stratigraphy. This information can be invaluable for selecting the best location for geotechnical boreholes and to map potential geohazards such as submarine slides and filled or open scour holes. Offshore investigations conducted for a proposed highway bridge (Knik Arm Bridge, Cook Inlet, AK), the retrofit of two existing bridge (Antioch and Dumbarton Bridges, CA) and a proposed cruise ship terminal (Ketchikan, AK) used a combination of geophysical methods to map water depth, detect and map debris on the seabed, map the thickness of unconsolidated sediment, determine the depth to bedrock and identify potential geohazards such as scour holes. The results of the geophysical investigations will be used to select locations for obtaining geotechnical borings, to extrapolate geologic information between existing or proposed boreholes, evaluate the potential depth of scour and design a pile support pier. Geotechnical engineers, offshore contractors and bridge designers are realizing the importance of the early use of offshore geophysics for (i) site characterization, (ii) to reduce the uncertainty of geotechnical conditions thus avoiding designs that may be overly conservative and thus more expensive and (iii) to assist in selecting locations for geotechnical borings.

May 11, 2007

By Frank Albrecht, Brian McCarthy

"The Ararat Terminal Station (ARTS) is located 190km to the north-west of Melbourne, approximately 1.7km to the north of Elmhurst Township in the Pyrenees region of western Victoria, Australia. The site occupies an area of approximately 7.2 hectare of farmland. The electricity generated by the Ararat Wind Farm is directed to the ARTS terminal station before being connected to the grid. The ARTS structural design includes more than 180 steel yard support structures, three 25m-tall gantry ‘A’ frames, three modular control room buildings, a precast transformer bund, precast fire wall structures and related foundation design. Innovative driven engineered glue laminated timber (glulam) piles in a cruciform shape were used to reduce the foundation construction time, cost and the amount of concrete used in the project. It is the first time that engineered timber piles made from farmed Australian pine trees have been used in a large-scale environmentally-friendly project. Durability of the timber was achieved by H5 treatment and the use of reinforced concrete pile caps to protect the cruciform timber piles at the ground line. A pile-driving sequence was developed based on field trials. The lateral load capacities of the piles were estimated using engineering principles and from full-scale tests in the field. This paper provides an overview of details of engineered timber cruciform piles, durability of timber piles, design information, pile construction procedures, pile-driving procedures, the testing protocol, test results and validation. The test results were compared with predictions from several methods. In addition, potential future applications of similar systems in other infrastructure projects, and opportunities for future improvements are discussed. The structural aspects of this project were presented in a previous paper at the World Conference on Timber Engineering in Vienna in August 2016. See http://wcte2016.conf.tuwien.ac.at/home/ for further information."

Jan 1, 1900

By Peter Faust, Peter Hubbard, Kenichi Soga

The European Federation of Foundation Contractors (EFFC) and The Deep Foundations Institute (DFI) have set up a task group to compile a Guide for Working Platforms. The first edition of this Guide has been published in January 2020. The aim of the Guide is to provide reliable methods for design, testing and verification of working platforms for construction equipment, especially in the deep foundation industry where track loads can be excessive due to the nature of its operations. The Guide has identified areas where knowledge is limited. Actual track pressure and its distribution along the length of the tracks is still not well researched. Current recommendation provided in EN 16228-1 are believed to be overly simplified and may lead to conservative requirements for working platform thickness. This paper presents results of a series of field tests where the actual track pressure of a large drilling rig during operation was measured in real time together with the deformation of the working platform. Embedded, distributed fiber optic sensing (DFOS) at different depths throughout the platform allowed for a three-dimensional evaluation of the platform deformation throughout the entire operation. Results will help to develop more reliable recommendations for future safety requirements of working platforms for deep foundation equipment.

May 1, 2022

By Kyle R. Lackner, Jared P. Williams

"The Sutter Butte Flood Control Agency initiated the Feather River West Levee (FRWL) Program in 2010 to bring 35 miles of levee along the Feather River into compliance with applicable Federal and State standards for levees protecting urban areas. A combination of soil-bentonite cutoff walls, soil-cement-bentonite cutoff walls, and seepage berms will reduce flood risk by correcting under and through seepage deficiencies and remove more than 34,000 properties from the FEMA Special Flood Hazard Areas. The FRWL program includes a combined total of 7,744,803 square feet (SF) of cutoff wall planned to be constructed between 2013 and 2015. Cutoff wall construction methods to meet the design depths included conventional excavation to a depth of 85 feet and deep soil mixing for depths up to 120 feet. A key component of the FRWL program was the development of site specific mix designs using the design boring logs to evaluate the expected backfill gradation and permeability results. Issues that required a partnership between Contractors, Owner and Engineers included substantial Archaeological and Cultural Resource delays, significant depth changes due to a change in competent key, right of way acquisitions for abutting land, and the magnitude of the project in a resource limited industry.IntroductionThe Feather River watershed basin is located 50 miles north of Sacramento, CA and incorporates the agriculture producing communities of Yuba City, Live Oak, Gridley and Biggs. These communities are protected from flooding by levees that contain under-seepage and through-seepage deficiencies and were the cause of major failures in 1955, 1986 and 1997. The Feather River West Levee (FRWL) program was initiated by the Sutter Butte Flood Control Agency (SBFCA) in 2010. The long term objective of SBFCA is to correct the levee deficiencies and provide 200 year flood protection to more than 34,000 at risk properties located within the FEMA Special Flood Hazard Areas.Although FRWL contained a variety of construction components such as earthwork and pipe replacement, the slurry cutoff wall is the primary construction element for addressing under and through seepage deficiencies. From 2013 to 2015 approximately 6,649,210 SF of cutoff wall were installed using conventional excavation and deep soil mixing (DSM) techniques leaving 1,095,593 SF to be completed in 2016. The work was designed, solicited and constructed under two separate contracts, titled Project Area C and Project Area B&D. A summary of the contracts and cutoff wall quantities is presented in Table 1."

Jan 1, 2016

By Ed Revoort, Robert Schippers

In Rotterdam in the Netherlands the project ‘De Zalmhaven’ is being developed. The project consists of the realization of houses, parking facilities, two residential towers of 70 m and a residential high rise of 215 m. An artist impression for the project is given in figure 1. For the high rise a new development in the use of large diameter, drilled piles with a steel casing has been successfully utilized. In this article the installation method of 65 m long steel drilled piles in two consecutive sections is presented. The settlements for the building (and the influence on its surroundings) have been analyzed in detail using 3D Finite Element calculations, which will also be discussed. Finally there is focus on the results of settlement measurements carried out during construction in relation to the settlement prognosis.

May 1, 2022

By N. V. Nayak

Konkan Railway Project is one of the most ambitious railway construction projects in India, involving construction of a 760.km long, Broad Gauge (1676 mm), single track railway line, connecting Roha in Maharashtra State with Mangalore in Kamataka State. The railway line travels along the Western Coast of Indian subcontinent, through states of Maharashtra (382 km), Goa (105 km) and Karnataka (273 km) (Fig.1). The project alignment traverses through one of the most formidable terrains ever encountered, in the history of railway construction in India. In the State of Goa only, railway alignment is crossing 6 major rivers Terekhol, Chapora, Mandovi, Zuari, Sal and Talpona. Zuari Railway Bridge (1305.6 m), Mandovi Railway Bridges (I and II) (1182.7 m) rank as 2nd and 3rd long bridges, (first longest bridge being Sharavati Bridge (2.2 km} at Honavar) which have been constructed on Konkan Railway. All these three bridges have been constructed by M/s.Asia Foundations and Constructions Ltd. (AFCONS). This paper presents, case history of construction of pile/caisson foundations for Zuari and Mandovi Bridges.

Jan 1, 1996

By George W. Little, John Councilman

"The selection, evaluation, and modification of contractor mix designs for self-hardening seepage barriers, completed by the slurry trench excavation method, can be one of the most critical and challenging tasks to ensure the cutoff wall meets the design performance criteria. Contractor mix designs should incorporate all available geotechnical data, including subsurface soil characteristics, groundwater information, and potential site contaminates. However, the pre-construction mix design can have limitations if subsurface data is limited or shows variability from initial investigations. Placement of the seepage barrier material needs to be evaluated during construction to identify in-situ performance. In one particular case study, the self-hardening cutoff wall mix design was evaluated over a one year period followed by a year and a half installation period, in which, a number of adjustments were made to the laboratory mix design during construction due to performance in the field. Installation for the selected mix was monitored on a real-time basis, using quality control data, as well as early strength and permeability results to determine if adjustments to the self-hardening mix were necessary. Evaluation of early results and relationships between strength and permeability were used to make adjustments prior to achieving the final test results for 28-day strength and permeability. Test results of the installed mix illustrated a direct correlation between strength and permeability. Achieving a minimum unconfined compressive strength was necessary to meet the minimum permeability of the seepage barrier. Other determinations conclude that the thorough development of a pre-construction mix design can have limitations even when all geotechnical data and site conditions are taken into account. Understanding early indicators and key strength and permeability relationships are necessary to determine seepage barrier performance and limitations.IntroductionThe evaluation of contractor mix designs for self-hardening seepage barriers was reviewed for one particular case study where a mix was developed using available geotechnical background information, including considerations for impacted groundwater. Following development of the laboratory mix design, the seepage barrier wall was installed over a one and a half year period, where the contractor mix design was evaluated and modified to accommodate field conditions affecting performance. The objective of the project was to cutoff and collect impacted groundwater and prevent the migration of contaminants to the creek running adjacent to the project. The self-hardening seepage barrier wall was installed using the slurry trench excavation method along 4700 ft of alignment and extended to depths ranging from 20 to 85 ft below ground surface, where it tied in with a low permeability stratum or competent bedrock."

Jan 1, 2016

By Josef K. Alter

Long-term performance and behavior of post-tensioned ground anchors subjected to axial cyclic loading constitutes an important aspect of the stability, reliability and overall performance of wind turbine deep foundations. Axial cyclic loading of post-tensioned (PT) ground anchors in soils has not been thoroughly investigated as evidenced by the research conducted for this topic. This paper evaluates research test data, available literature, and industry expert opinion on the current status and problems of deep foundation post-tensioned ground anchor (PTGA) technology, as applicable to the wind energy industry. It also introduces a proposed design solution that addresses the problems of construction cost and long-term performance of wind turbine deep foundations in soils subjected to dynamic cyclic axial loading. Deep foundations using ground anchors for wind turbines have only recently gained attention as a possible viable alternative to the mass spread footings currently in use. One of the primary problems with general acceptance of current PTGA designs is the need for long-term anchor maintenance. The research that was conducted for this study indicates that current literature only partially addresses the many factors influencing load capacity and pullout performance of ground anchors. The lack of information indicates the deep foundation industry has fallen behind in designing and implementing new technology to improve safety and performance, ensure sustainability, reduce costs, and address environmental responsibility. This paper describes the significance of this problem as it applies to the wind energy market, and proposes a new technology solution. The research, expert opinion, and analysis presented by the author is used to support the premise that ground anchor construction cost and long-term maintenance can be reduced with PTGA systems using the Con-Tech Systems (CTS) patent-pending Groutable Void Form (GVF) technology.

Jan 1, 2010

By Greg Halsted, Joshua Gilman

Today's civil and geotechnical engineers play an important role in helping to achieve sustainable infrastructure. To address environmental sustainability and climate change caused by green- house gas (GHG) emissions, all engi- neers must adjust their traditional approach to materials, design and construction practices to include a focus on minimizing carbon dioxide emissions. The considerable influence that geotechnical engineers have on projects provides an important oppor- tunity to affect positive change. The carbon footprint of the construction methods and materials used for foun- dations can be as much as 8-9% of a new building's total carbon footprint, and geotechnical engineers have an op- portunity to evaluate alternatives based not only on cost, but also the long-term environmental impacts. Growing environmental considerations and societal concerns are influencing the selection of construction materials and methods, including cement and concrete's role and significance for infrastructure applications today and in the future.

Jan 1, 2023

By Charles G. Crans, Naresh Gurpersaud

"Toronto’s Union Station, a National Historic Site occupying an entire city block, is the busiest commuter rail transportation hub in Canada. An extensive project is being undertaken to revitalize Union Station while maintaining the historical significance of the building and minimizing disruption to commuters. A significant stage of the revitalization involves excavation indoors, to a depth of up to 5.5 m below the existing floor level to create space for a new transit concourse and a new lower-level pedestrian retail concourse. A hybrid excavation support system utilizing micropiles as soldier piles was constructed over an 18 month period between 2010 and 2011.Development and testing of connections between the micropiles, shotcrete facing, lagging, walers, and tiebacks presented significant challenges. The existing viaduct structure was constructed in the 1920’s on land reclaimed from Toronto Harbour, so there was significant (and ongoing) uncertainty with respect to buried obstructions including relic timber wharfs and abandoned steel and timber piles. Collectively all these conditions precluded the use of conventional methodology; new techniques, installed using modified equipment, and for the first time in the Greater Toronto Area, were required.Details of the existing site conditions, installation challenges, design, construction and performance of the hybrid excavation support system inside this historic structure are presented.INTRODUCTIONUnion Station in Toronto, Ontario is the busiest passenger rail facility in Canada, with 65 million passengers annually and an average of 200,000 passengers each day. Construction of the station was completed in 1920. It has been designated a National Historic Site of Canada and inducted into the North America Railway Hall of Fame in the Facility and Structure category.The Union Station Revitalization Project (USRP) was tendered in 2010 and awarded as a 6-year, $450M construction management / trade contract package. Included was a large scale grade reduction, referred to as “The Dig Down”, to create two basement levels and this required extensive excavation support constructed entirely indoors within the active station setting."

Jan 1, 2017

By Marcus Daubner, Karsten Beckhaus, Florian Bauer

The construction industry can and needs to contribute to a more sustainable world. Accordingly, geotechnical works potentially have a significant share. In this context, Bauer understands “sustainable products for geotechnical works” as those that may cause less emissions and increase the sustainability of construction activities. In order to structure the efforts and systematically pursue sustainable targets in the construction sector, and in the specialist foundation industry, the “17 sustainability goals” presented by the United Nations in their AGENDA 2030, can be used for general guidance and for continuous improvement. Benchmarks for relevant economic and social objectives, mainly with environmental aspects, are inevitable. The key parameter to sustainable products for geotechnical works in the focus of this paper is the optimisation of processes on site needed to fulfill the client’s building task, including the selection of technologies and construction methods with minimum environmental impact and minimum carbon footprint.

May 1, 2022

By Darrell L. Beddard

The test program information provided for some immediate changes on the upcoming contracts and in contract administration for the I-880 Replacement Project. Plan sheet modifications included changes to the pile data tables showing the actual demand load required for structural stability. The normal class of pile with a minimum load carrying capacity was removed. This provided for substantial pile length reduction at several locations since the structural loading was much less than the predetermined pile class ultimate capacity. New specifications were developed and standard specifications were modified to accommodate the newer foundations, installation procedures and pile acceptance criteria. Current Caltrans specifications require that the Contractor provide bearing capacity at the specified tip elevation. This requirement was removed and pile acceptance was determined by the Engineer. Acceptance criteria was established by the State and was based on. set-up trend over time. Static loading tests were reduced especially in areas where testing was performed on the indicator program. Testing procedures were modified and set-up periods were established before piles could be tested. For the contract near the San Francisco Oakland Bay Bridge (Unit E) the FHWA 1000 tons (8.9 MN) test beam configuration was completely changed. This provided added safety and allowed more tolerance in the pile placement for the testing operations. Indicator piles were added as companion piles to the static loading test piles. These piles were used for restrike events which included collecting dynamic data for calibrating the wave equation analysis with static load test results. Indicator piles also provided quick access for restrike events, where as, the static loading test pile needed modification to perform the restrike operation. Penetration rates were recorded for these operations. Wave equation Analysis Program (WEAP) was used in developing the acceptance criteria. The standard Engineering News Record (ENR) formula in the current Caltrans' Standard Specifications was removed for the contracts. Contractors were required to submit, prior to driving piles, a driveability study for their contract. These studies required discussion of their operations, method of installation, effects of soil set-up, set periods, hammer settings, bearing graphs, inputs to the WEAP program and complete a "Pile and Driving Equipment Data" form. Dynamic monitoring was detailed in the specifications on how the monitoring process was to occur. Set periods were established and restrike events were called out with the frequency of these events.

Jan 1, 1996

By Douglas L. Scaggs

Driving piles in under water applications has become more common place over the past twenty years. Where only a water depth reachable with a follower or dewatered cofferdam was the rule in the past, newer technologies developed for the offshore oil and gas industry have made depths of even several thousand feet possible offering new possibilities in foundation design and installation. With the new technology, engineers can now more efficiently design structures by placing foundations optimally thereby reducing weight and cost of the overall structure.

Jan 1, 2013

By J. Erik Loehr, Andrew Z. Boeckmann

"Poor drainage is a common cause of poor performance of earth retention systems, resulting in burdensome serviceability problems that can progress to outright failure of the retention system if not addressed. A drainage system consisting of filtered conical drains that can be installed through the face of an existing retaining wall and readily maintained was evaluated through tests of physical and numerical models. The physical models were constructed with different backfill materials in a container measuring 8 ft wide by 4 ft tall by 15 ft long. Tests were conducted by saturating the backfill under a constant water elevation atop the model, and then maintaining the water elevation until seepage from the drains reached a steady state condition. Pore pressures within the backfill and outflow from the drains were measured to facilitate calibration of numerical models that accompany the physical models. Results from the calibrated finite element models were used to develop design criteria for the drains. The design criteria establish the required drain spacing as a function of the height of groundwater above the drains and the diameter of the drain.INTRODUCTIONMany retaining wall performance problems are a result of poor drainage of the wall backfill. Consequences of poorly drained backfill include displacement and rotation of the wall face, including the extreme case of collapse, and seepage through the face of the wall, which is in turn associated with damage from corrosion, dry rot, and other forms of deterioration. A common approach to improve drainage of an existing wall is the installation of drainage features (e.g. “weep holes”) in the face of the retaining wall. Weep holes facilitate controlled seepage through the face, which relieves water pressure within the backfill and directs seepage to known locations in the wall face. Although installation of weep holes is relatively common, engineering methodologies for selecting the size (diameter) and spacing (along the wall) of facial drainage features are uncommon if not altogether non-existent. This paper documents tests of physical and numerical models of retaining walls with facial drainage features, including conventional weep holes as well as maintainable drains installed through the face and extending into the wall backfill. Results of the testing were used to develop generic design criteria, which establish the required drain spacing as a function of the height of groundwater above the drains and the diameter of the drain."

Jan 1, 2016

By Ahmed H. Bukhary, Naser A. Al-Shayea

The objective is to assess the overconservatism in the parameters used for designing offshore piles. Methodology includes analysis of shaft friction data obtained from more than five different locations in the Arabian Gulf, consisting of 40 piles to depths up to 86 m. Reports were collected for both the dynamic pile monitoring system (DMS) and their corresponding geotechnical reports based on the American Petroleum Institute (API). The values of shaft capacity for the sand layers were analysed by comparing those based on API to the corresponding DMS values. Results of the comparison of the data from these reports showed that the pile design parameters obtained using API guidelines is generally smaller than that measured by DMS. The difference is presented in terms of an overconservative factor (OCF) which is adjusted based on statistical nonparametric test performed on the two data sets. The adjusted OCF were found to be 1.79 and 2.00 for carbonate sand at (loose to medium dense) and (dense to very dense) conditions, respectively. The corresponding values for silica sand were only 1.2 and 1.06. In conclusion, based on the evaluation conducted for data from these reports, the API shaft friction is overconservative for carbonate sand. The API shaft friction for piles in sand can be increased by multiplying it by the adjusted OCF.

By Morris J. D, Baldwin Z., Wiltcher P. M

21 Moorfields is an oversite development in central London spanning Moorgate tube station. It required the installation of both the highest loaded bearing piles and the highest top loaded static pile test ever undertaken in the UK, at 50.5MN (5,680 tons). The 17-storey building is founded on only 15 large diameter bored piles installed through the roof of the live station. The piles are located in two parallel rows 50 m (164 ft) apart, bridging the underlying train lines and the Crossrail tunnel below. This unique project required a diverse cross-section of skills and experience from the Project Team as we not only pushed the boundaries of design but also those of construction practices. Our team therefore needed to be made up of members from multiple businesses and disciplines. The team worked together, in a highly collaborative environment, for around two years before any work started on site. A key challenge for this project was that there was only one opportunity to construct each pile. If a position had to be abandoned there were no alternative locations and the impact on the project would have been catastrophic. It was therefore vital that all events that may have led to the abandonment of a pile were investigated ahead of commencement on site. Risk elimination and mitigation strategies were developed for all eventualities whether they be associated with the design or construction processes. The successful pile load test, coupled with all contract piles being fully instrumented with state-of-theart fiber optic (CemOptic) cable along their full length, has improved our understanding of the performance of such large and heavily loaded piles. The works piles will all be monitored during the construction of the new building, providing new insight into their real-world performance. Such groundbreaking work has never been undertaken before in the UK and has the potential to significantly influence the industry’s understanding of pile behavior, and design, in the future. This paper will discuss the challenges the team encountered during the design and construction of this highly complex urban project, particularly when adopting, by necessity, a pioneering approach.

By Alexander Blatt, Franz-Werner Gerressen

Diaphragm wall technique is usually used to construct structural elements in the ground, commonly used for retention systems, permanent foundation elements or deep groundwater barriers, named Cut-Off-Walls (COW). Recent developments proof, that the technology also satisfies the demands for using the diaphragm wall technique for bulk sampling purposes. Such kind of new ideas required the adaption of equipment and tools for a depth capability never reached before by a trench cutter in any commercial application worldwide. Compared to the development of increasing depths, especially inner-city applications with limited space, demand a minimization of equipment to accommodate such projects. The paper will focus on the developments and solutions generated to fulfill these requirements and will give an outlook to future developments. Further it describes finalized reference projects and will give a general outlook on future trends and developments. The Paper/The Presentation explains as well the installation process in general.

May 1, 2022

By Pier Luigi Iovino

As Technical Director of the Naples, Italy based Fondedile, a geotechnical construction firm specializing in static restoration of structures, Fernando Lizzi, Ing., devoted over 30 years to the pursuit and advancement of static restoration and subsoil strengthening. Seismic events, construction of new structures on polluted and/or unstable soils in urban areas, and a need to carefully preserve and restore delicate, war-damaged historical structures, manifested the need for underpinning projects. Traditional construction methods and approaches, such as underpinning with additional foundation masonry, were not suitable and would have further jeopardized the stability of the structures. The introduction of the palo radice (root pile) revolutionized the field of underpinning. At the time of the first application of micropiles, the industry standard was driven piles. The drilled micropile was conceived and first implemented in the early 1950s, as an innovative means to underpin sensitive, historic structures and structures in urban areas. Specifically, the new construction technique was conceived as a less expensive alternative, designed to accept structural loads, be installed in limited access areas, in varied working and sub-surface conditions, which did not involve changing soil characteristics, and had minimal disturbance to the structure being underpinned, or to adjacent structures.

Jan 1, 2003