Search Documents

By Kyle S. Brinkman, Kenneth L. Reifsnider, Fazle Rabbi

"Mixed ionic and electronic conducting (MIEC) ceramic membranes are HeteroFoaM's which play an essential role in a number of energy conversion related systems including the solid oxide fuel cell (SOFC), oxygen separation and permeation membranes, partial oxidization membrane reactors for natural gas processing, and high temperature electrolysis cells. Dual phase oxygen membranes consisting of an ionic conducting phase Ceo.sGdo.z02 (CGO) and an electronic conductive phase C0Fe204 (CFO) were fabricated and characterized by structural (XRD), microstructural (SEM-EDS) and broadband dielectric measurement techniques. In-situ measurements of the dielectric properties of working oxygen separation membranes are presented which indicate that the material's dielectric behavior can be an indicator for MIECperformance.IntroductionCeramic membranes which transport oxygen ions play an essential role in a number of energy conversion related systems including the solid oxide fuel cell (SOFC) [l ], oxygen separation and permeation membranes in the commercial and nuclear arena [2, 3], partial oxidization membrane reactors for natural gas processing [4], and high temperature electrolysis cells [5]. For the electrolyte functions, the membranes must transport oxygen ions only. On the other hand, permeation membranes, typically used in combustion devices to support oxy-fuel combustion or for partial oxidation reactions involving the production of synthesis gases, require mixed oxygen ion and electronic conduction (MIEC). Traditionally the tailoring of the ratio of ionic conductivity to the materials electronic conductivity, measured as the transference number, has been accomplished by the introduction of aliovalent doping elements creating point defects in the material facilitating the diffusion of charged species. However, several decades of research have not yet produced single phase materials which possess the concomitant ionic and electronic conductivity required for use in membrane separation applications. It is clear that novel ""dual phase"" heterogeneous materials will be required and that the surface reactions of these materials will be of particular importance as the industry moves toward thin films membranes [6]."

Jan 1, 2013

By M. Brian Maple

A rich variety of phenomena are produced by superconducting-magnetic interactions in rare earth and actinide compounds. These phenomena, and the materials in. which they have been observed, are described in this talk, with an emphasis on the new high superconducting transition temperature (Tc) copper oxides. The Materials The-materials in which these phenomena occur can' be divided into two classes. In the first group, there are two distinct interpenetrating systems of electrons, a set of localized 4f or 5f electrons and a set of itinerant electrons. The localized f electrons carry magnetic moments and interact with the spins and momenta of the the itinerant electrons, which are involved in the superconductivity, via exchange and electromagnetic interactions; respectively. This category includes materials containing rare earth (R) and actinide elements with partially-filled f electron shells which have been inroduced as substitutional impurities [e.g., La1-xCexA12, Th1-xUx] or form a sublattice in compounds [e.g., RRh4B4, RMo6S8, RMo6Se8, the high Tc. superconductors RBa2Cu3O7-d(d - 0.05)]. Materials of the second type are characterized by a single band of electrons that is responsible for both superconductivity and magnetic order. This group includes heavy electron rare earth and actinide compounds [e.g., CeCu2Si2, UBe13, UPt3, URu2Si2], and the high Tc copper oxide superconductors such as the hole-doped systems Lag- MxCuO4 (M = Ca, Sr, Ba, Na) and RBa2Cu3O7-d(0 =d= 1) and the electron-dope system Ln2-xMxCuO4-y (Ln = Pr, Nd, Sm, Eu; M = Ce, Th; x = 0.15; y - 0.02).

Jan 1, 1992

By M. Okido, H. Yamamoto, T. Sakamoto, R. Ichino, K. Kuroda

"Hydrogen absorption alloy films have been produced by molten salt electrolysis. Lanthanum-Nickel alloy film can be formed on a nickel substrate in KCl-NaCl-LaCb molten salts by electrolysis diffusion process. LaNi5 alloy was formed by mutual diffusion between La ·and Ni after La deposition on Ni substrate. Though several kinds of La-Ni compound existed in deposits, the alloy compounds on Ni substrate changed by electrolysis condition. According to the open-circuit potential measurement in molten salts after La electrodeposition, the formed compounds had a relation to the potential. In the case of the substrate electroplated a cobalt thin film on nickel, LaNi4_5Co0.5 was formed by the electrolysis in the molten salts with lanthanum ions. This ternary alloy film showed better hydrogen absorption behavior in cyclic charge/discharge test in alkaline solution.IntroductionHydrogen storage alloys have attracted attention as the active materials for batteries with the charge/discharge property at ambient temperature. The alloy of nickel and misch metal, mainly consisting of La and Ce, has been commercially 'used as a metal hydride with rechargeable property. In recent years, researches have been developed many kind of new alloys with better hydrogen absorption properties. The hydrogen absorbing alloy ingots are commonly produced by melting method of both metals in furnace, otherwise, prepared by mechanical grinding and metallurgical sintering technique with metal powders. The film is also made by vapor-phase techniques such as sputtering method, ion plating method, etc. ·We have proposed a new method to produce hydrogen absorbing alloy films by molten salts electrolysis technique [1-3]. The hydrogen absorbing film, LaNi5, Mg2Ni and CaNi5, were obtained in this process through controlling the electrolytic condition. The active metals, La, Mg and Ca, are electrodeposited on Ni substrate, diffuse into the substrate and form various kinds of intermetallic compounds. This technique provides a direct process using metal chlorides as resources to produce functional films without using active metals such as La, Ca and Mg."

Jan 1, 2000

By Józef Czernecki

Chalcocite-bornite concentrates of KGHM contain, similarly to chalcopyrite concentrates, 20-30 wt.% Cu but several times less iron (2-7 wt.%) and sulphur (9-12 wt.%). Another useful characteristic of KGHM concentrates is the presence of organic carbon (5.5-8.5 wt.%) in them, which serves as fuel in the flash smelting process. The main contaminants of the concentrates are lead (1.3-2.5 wt.%) and arsenic (0.05-0.4 wt.%) which require appropriate technological treatment in order to remove them from the copper pro-duct. Chalcocite-bornite concentrates are processed in KGHM by two different processes: ? a flash smelting process (Glogow 2 Smelter) ? a shaft smelting process (Glogow 1 Smelter, Legnica Smelter) The shaft smelting process used in the Glogow 1 Smelter and in the Legnica Smelter has higher production costs than the flash smelting process of HM Glogow 2. Additionally, the shaft smelting process employs several concurrently running installations (six dryers, seven briquetting lines, six shaft furnaces, nine converters), the operation of which, including maintenance, requires significant financial expenditure. Therefore, the Company is currently considering the substitution of the shaft furnace process in the Glogow 1 Smelter and in the Legnica Smelter by the one stage flash smelting process located in the Glogow Smelter, with output equaling the copper production capacity of both smelters, i.e. 320 000 ? 350 000 t/a. There are two technological options being considered which differ from each other in their man-ner of flash slag cleaning. In the first, the slag cleaning would be the same as in the existing Glogow 2 Smelter, i.e. the slag would be cleaned by pyrometallurgical reduction of the oxide copper and other metal compounds in the electric furnace in order to produce waste slag containing below 0.6 wt.% Cu. However, the other option of the flash slag cleaning would be carried out in two stages. After preliminary slag reduction in the electric furnace to 3-5 wt.% Cu, there would be flotation of the partially reduced slag.

Jan 1, 2006

By Ki Bui Ma

Momentum wheels with superconducting bearings can integrate both attitude control and energy storage functions, with attendant savings in the total volume and weight of hardware, and power consumption, all of which are in short supply on mini-satellites. We have built and tested a prototype with a wheel of mass 1.9 kg, diameter 3.25 in, and height 3 in, which can store 3.5 J-sec of angular momentum and 5 kJ of energy when it rotates at an angular speed of 15000 RPM. The energy density of 2.5 kJ/kg achieved is comparable with the lower range for lead-acid batteries. To show that the wheel is energy efficient, we have performed spin down tests and measured the input power required to sustain rotational speed. Results indicate that power consumption, even accounting for the needs of cooling system, is significantly smaller than that for state of the art commercial reaction wheels.

Jan 1, 2002

By M. F. Hochella

Transmission electron microscopy (TEM) and energy dispersive X-ray (EDX) analysis have been used to study the mode of occurrence and mineral associations of gold in partially oxidized high grade gold ore from the Carlin sediment-hosted deposit. Rounded.gold particles have been observed that range in size from 0.03 to 0.1 p.m (300 to 1000 A) in diameter. The gold is associated with maghemite h-Fep3l and a K-Al-Si-bearing phase that is suspected to be illite. Detailed descriptions of gold and its mineral associations in 'Carlin-type' gold deposits are critical not only to understanding the mechanism of fluid transport and precipitation of gold, but also to developing improved metallurgical techniques for the recovery of gold from refractory ore. Direct observation of gold in unoxidized ore is rare due to its relatively high degree of dissemination and low average bulk concentration which averages 9 ppm according to Radtke (1). Hausen and Kerr (2) observed 1 to 5 p.m grains of gold directly in oxidized ore but these microscopically visible particles account for only a small percentage of gold present in the ore. The samples used in this study were selected from individual beds of high grade, partially oxidized ore (4.55 oz/ton or 156 ppm gold) that were collected in the Main pit of the Carlin mine. The samples were collected from several thinly laminated carbonate micrite beds within the top 50 meters of the Roberts Mountains Formation. The carbonate micrite has been altered by hydrothermal fluids to a calcite-absent, moderately silicified rock referred to as alteration zone #3 by Bakken and Einaudi (3). Based on petrographic and SEM studies, the samples contain carbonaceous matter, and both pyrite and iron oxide pseudomorphs after pyrite. The oxidation of pyrite may be a pro-duct of deep weathering, in which case limited remobilization of gold may have occurred. TEM sections of the rock were prepared by first embedding small chips in low viscosity epoxy. The epoxy blocks were cut with a Reichert Ultracut E ultramicrotome, producing thin sections less than 0.1 p.m thick. The sections were examined with a Phil-lips 400ST TEM at 120 keV in both imaging and selected area diffraction modes. Native golci*was easily detected in TEM bright field images due to the large electron density contrast between gold and all other phases that are present (Figs. 1 and 2), Gold was positively identified with high spatial resolution EDX analysis in the transmission electron microscope, although selected area diffraction of individual grains was not successful EDX analyses of the platy and massive minerals immediately surrounding the gold particles typically indicate the presence of Si, AI, K, and Fe, However, the d-spacings derived from selected area diffraction of these polycrystalline masses (as, for example, in Fig. 2) give an exact match for maghemite. As a result, there is no diffraction information to identify the K-AI-Si-bearing phase(s). The lack of a diffraction pattern could be due to either electron beam damage or to a poorly crystalline phase(s).

Jan 1, 1987

By E. M. Alcântara

This paper describes some aspects about the relationship between copper electrorefining addition reagents and the hydrogen in the cathode. The conditions of electrorefining were studied by factorial design methods. The advantages of this technique are reduction in the number of tests, well organized experiments; improvement in productivity and reliability of results. The dosage of the two main addition agents, glue and thiourea, were varied simultaneously and compared with the hydrogen content in the cathode. The influence of these factors, as well their interactions were analyzed by statistical methods denominated ANOVA (Analysis of Variance). The increase of thiourea quantities, within of levels studied, influenced significantly at 95% confidence in the hydrogen content in copper cathode.

Jan 1, 1999

By Minjun Tang, Jianfeng Zhou, Linjiang Qing, Yufeng Guo, Tao Jiang

"For the comprehensive recovery ofV, Ti, Fe in vanadium-titanium magnetite in the process of pre-reduction-electric furnace smelting, it is expected that vanadium oxide is reduced into molten iron and titanium oxide is available in the slag. Thus the effect of slag basicity, the content of MgO, MnO and CaF 2 of slag content on the separation of slag and molten iron and the comprehensive recovery of V, Ti, Fe were investigated. The results show that increasing slag basicity, MgO, MnO and CaF2 are all beneficial to the separation of slag and molten iron. Higher slag basicity and the addition of CaF2 strengthen the reduction of vanadium oxide, and inhibite the reduction of titanium oxide, which are in favour of the recovery ofV and Ti. However, the addition ofMgO, MnO was not efficient for the comprehensive recovery ofV, Ti, Fe. For the vanadium-titanium magnetite of Panxi in China, the recovery of Fe was over 98%, the recovery ofV in molten iron was over 85% and the Ti02 content in slag was about 43% under the optimal conditions of slag phase type.IntroductionIt is well known that there are abundant vanadium-titanium magnetite resources which are located in Panzhihua of Sichuan Province[!]. At present the vananium-titanium magnetite concentrates are smelted in the blast furnace, which just make use of iron and vanadium, but lots of titanium is discarded in the slag. At the same time, the process has a large number of disadvantages, such as low recovery of vanadium, long route, pollutions, large investment and expenditure of energy[2-3]. In recent years, in order to efficiently utilize the vanadium-titanium magnetite concentrates, several new non-blast furnace processes have been proposed, such as pre-reduction-electric furnace, pre-reduction-grinding separation and so on[4]. Especially pre-reduction-electric furnace is operating well in South Africa and New Zealand,However,Du to the high slag basicity of the slag, the grade ofTi02 of slag is Corresponding author:Minjun Tang.E-mail:450435123@qq.com. Tel:13627429224."

Jan 1, 2013

By Okechukwu Anopuo, Gerhard Tober, Petra Maier

"In this study, an investigation on the microstructure of hot rolled steel S355J2+N was conducted to optimize process parameters of complex forming, which combines rolling and bending. The best sets of parameters are worked out based on homogeneous mechanical properties and microstructure within the varied deformation degree with maximum at <p = 1.14 on a 25 mm thick plates. Mechanical properties, especially of heavy plates, are strongly influenced by the local deformation degree, strain rate and temperature. Detailed microstructural analyses showed that the ferrite-pearlite band structure changes near the surface, while maintaining homogeneous microstructure within the deformed work piece. Surface decarburization was also observed and this leads to decrease in hardness. To minimize iron oxide formation which could lead to side cracking, reduction in exposure time to temperature was suggested. On the other hand, temperature reduction below a critical value would risk the accurate forming process.IntroductionThis work presents the preliminary results of research to develop a new complex deformation process of thick steel plates. Complexity is given because the forming process combines rolling to reduce thickness and profiling by bending. The work piece will experience a thickness reduction from 25mm to 8 mm and is double curved. To explain and understand forming of thick plates basics of sheet forming as well as massive forming need to be used. At the moment there is no forming process established to produce double curved plates including reducing thickness in one process step. Technologies nowadays consist of two process steps: flat rolling and pressing in shape. Due to good weldability and formability the final product will be made of steel S355J2+N. This low-carbon steel is well understood and has a low strengthening exponent, which is expected to keep the forming forces down. Reduction of thickness from 25 mm to 8 mm gives furthermore a high deformation degree. Thus, hot forming has to be applied. The determination of process parameters is the main aim of overall research project; temperatures above lOOO°C are expected. Flow curves in literature are given at various temperatures and strain rates [1]. However, experiments with data close to the industrial application are rarely found, especially at low strain rates and high deformation degrees. Pre-test were done by flat rolling, being aware that the influence of bending is eliminated. The microstructure evolution were characterised in relationship to material formability with special attention to grain size change and recrystallization. Representative samples should be selected from specific locations in the deformation zone according to the knowledge about the metal forming process [2]. Due to no further alloying elements in S355, no precipitation hardening is expected to take place during hot forming, which keeps the mechanisms simple and the concentration on the feasibility of the complex forming process is given."

Jan 1, 2012

By Li Zhang

A novel green technology to recovery Titanium compounds from Ti-bearing blast furnace slag under the dynamic oxidation condition was developed and tested. Air was blown into the molten slag as oxygen resource through a lance during the dynamic oxidation process, in which six important results were found: (1) The TiC, (Ti2O3), Fe and (FeO) in the slag were oxidized; (2) The temperature of slag temperature rapidly increased; (3) The viscosity of slag decreased; (4) The coalescence, growth and drop of the metallic Fe droplets in the molten slag were carried out under an air agitation condition; (5) The dispersed Ti components were selectively enriched into the perovslite phase, and the perovskite phase could be selectively precipitate and grow. And also, the perovskite phase can be separated by the dressing method. The oxidation of molten slag gives off a large amount of heat, which helps chemical reactions proceed, improve the rate of chemical reactions, and promote the precipitation and growth of the perovskite phase. The features of the technique are clean, low cost and a great capacity to deal with a large quantity of slag. It was confirmed by experiments that the precipitation of the perovskite (CaTiO3) in molten slag is obviously affected by operation factors such as temperature, chemical composition, heat-treatment, additives and so on. The precipitating kinetics and mechanism of the perovskite phase from molten slag during the dynamic oxidation processes were also investigated.

Jan 1, 2006

By A. Siegmund, R. D. Prengaman

Lead anodes used in zinc electrowinning generally contain 0.5 - 1.0 % silver to reduce the rate of corrosion over the service life. For good quality zinc, the cathodes must contain less than 10 ppm lead. In order to reduce the lead contamination of the cathode, the lead anode must become coated with a protective layer of Pb02/Mn02. The formation of this layer may take as long as 30 - 60 days, during which time zinc production is substantially reduced and the cathodes are contaminated with lead. To improve the mechanical properties of Pb-Ag-anodes alloying elements such as calcium, strontium, barium and others are added. The production of cast lead-silver or lead-silver-calcium anodes often results in the formation of numerous holes, voids or laps in the anode surface that can initiate localized internal corrosion. Based on the experience as the major supplier of rolled anodes for copper electrowinning, RSR Technologies has developed an improved anode for zinc electrowinning. The anode consists of a rolled Pb- Ag-Ca-alloy with a controlled surface grain structure. It forms an adherent protective oxide coating within 2 - 3 days when placed in an electrowinning cell. The preferred calcium and silver contents of the alloy are 0.03 - 0.08 % and 0.3 - 0.4%, respectively. Rolling sheets significantly reduces the presence of internal porosity or laps. The lack of defects results in long anode life. The rolling also produces a uniform grain structure to which the corrosion product readily adheres, thus significantly reducing the conditioning period.

Jan 1, 2000

By Suguru Kohno, Yoshihiro Momose, Masakazu Honma, Tokirou Kamosawa

Copper metal surfaces have been examined by an extremely sensitive surface analysis technique called temperature programmed photoelectron emission (TPPE). The surfaces were ultrasonically cleaned and subsequently abraded by a screw in organic solvents and water. The TPPE apparatus is composed of a Geiger counter with Q gas (He+ iso-C4H10). The curve of photoelectron emission (PE) intensity vs. wavelength from 300 to 170 nm, termed PE spectrum, was repeatedly measured at different temperatures in the temperature- increase process from 25 to 350°C. The number of emitted electrons in a PE spectrum (PE total count) increased, reached a maximum at-250°C, and decreased with increasing temperature. With the surfaces cleaned alone in the liquids the maximum PE total count decreased in the order C3H70H > (CH3) 2CHOH > C2HpH > CHPH > H2O. With the mechanically abraded surfaces in the liquids the maximum PE total count changed as a function of the abrasion period and the maximum tended to appear at higher temperature with increasing abrasion period; the maximum value at 10-min abrasion decreased in the order H2O > CHpH > C2HPH > (CH3) 2CHOH > n-C3HpH. It was suggested that the TPPE behavior can be related to the acid-base interaction between the alcohols and the abraded metal surfaces and the presence of a contaminant over layer on the surface. From the XPS analysis of the 01 s spectra it was suggested that the chemical change of the adsorbed oxygen to oxide oxygen with temperature plays a substantial role in the appearance of the maximum PE total count.

Jan 1, 2000

By Hiroshi Nakazawa

An acid mine drainage in abandoned Horobetsu mine in Hokkaido, Japan, contains arsenic and iron ions; total arsenic ca.10ppm, As(III) ca. 8.5ppm, total iron 379ppm, ferrous iron 266ppm, pH1.8. Arsenic occurs mostly as arsenite (As (III)) or arsenate (As (V)) in natural water. As(III) is more difficult to be remove than As(V), and it is necessary to oxidize As(III) to As(V) for effective removal. 5mL of the mine drainage or its filtrate through the membrane filter (pore size 0.45m) were added to arsenite solutions (pH1.8) with the concentration of 5ppm. After the incubation of 30 days, As(III) was oxidized completely with the addition of the mine drainage while the oxidation did not occur with the addition of filtrate, indicating the microbial oxidation of As(III). In this paper, we have investigated the microbial oxidation of As(III) in acid water below pH2.0.

Jan 1, 2006

By Xavier Kleber, Aude Lamontagne, Veronique Massardier, Daniele Mari

"The thermoelectric power (TEP) technique was used to determine with high accuracy the strain ageing kinetics in heavily cold drawn pearlitic steel. Because of the very high sensitivity of the TEP to solute atoms, this technique allowed the strain ageing to be followed from the very first moments. The kinetics were followed during isothermal ageings performed between 20°C and 200°C for different strains. In order to avoid any ageing at room temperature, the samples were kept at -80°C immediately after cold drawing. TEP evolution versus strain highlights cementite decomposition occurring during cold drawing. During the ageing, a redistribution of the dissolved carbon atoms in ferrite occurred. The TEP increase with the ageing time was attributed to the departure of carbon atoms from ferrite (segregation to dislocations and/or carbide precipitation). The kinetics were analysed using the Johnson-Mehl-Avrami-Kolmogorov approach which enabled to determine activation energies associated with carbon atoms redistribution.IntroductionHeavily cold drawn pearlitic steel wires are commonly used as structural materials for their high strength and their acceptable ductility. However, several previous studies highlight the microstructural destabilization of pearlite mainly due to cementite decomposition during the drawing process, which induces changes of mechanical properties [1, 2]. This phenomenon was detected by several experimental techniques such as Mossbauer spectroscopy [3, 4, 5], themomagnetic analyses [6, 7], TEM [8, 9, 10] or atom probe tomography [9, 10, 11]. Nevertheless, the mechanism of cementite decomposition is still unclear. Several hypotheses were proposed in the literature. The first hypothesis relies on a strong interaction energy between carbon atoms and dislocations involving higher binding energy than that between carbon atoms and iron atoms in cementite [3]. The second hypothesis is the increase of the free energy of the interface between cementite and ferrite due to the fragmentation of cementite during deformation (Gibbs-Thomson effect) [8]. Some authors even suggest that the dissolution of cementite occur during a post-deformation ageing [12, 13]. It is worth"

Jan 1, 2013

By B. Zeytuncu, O. Yucel, O. H. Celik, M. H. Morcali

"The Taguchi method was used as the experimental design to determine the optimum conditions of cementation behavior of the ruthenium chloride solution. Cementation was carried out using metallic zinc powder. The experimental conditions were studied in the range of 25-45°C for reaction temperature (A), 30--60 min for reaction time (B), 0.5-1.5 for pH of solution (C), and 30--50 mg for zinc powder (D). Experimental parameters and their levels were determined in the light of preliminary tests. Orthogonal array (OA) L9(34) consisting of four parameters each with three levels, was chosen. The optimal conditions found for ruthenium, such as a reaction temperature, reaction time, pH of the solution and mass of zinc, are respectively: 45°C, 45 min, 1.5 and 50 mg. Under these conditions, the ruthenium cementation efficiency obtained by theoretically and experimentally was in good agreement, which were 99.8% and 99.7% respectively."

Jan 1, 2013

By V. R. Voller

"The World Wide Web (the web) provides a very useful resource for the enhancement of teaching and research dissemination. This paper advocates that researchers take control of this resource and become actively involved in creating web content. Two examples of the use of the web in a materials setting is provided. The first illustrates how a concept quiz for teaching can be developed. The second shows how a materials processing model can be run in real time over the web. The paper closes with a summary of some resources that can be used to create web materials.IntroductionA recent copy of a newspaper advertisement read""Share what you know, learn what you don't""This neat phrase sums up a powerful teaching and research philosophy. In an educational setting a prime motivation for research is to uncover the unknown and venture in directions previously uncharted. The balance to this search for knowledge should be a desire to share that knowledge with others; whether it be with students in the classroom or research colleagues in a wider setting.The .World Wide Web and its associated multi-media software offer a perfect platform for researchers to share their knowledge with an extremely wide sector of the research community. To enable the use of this resource researchers must take the power that the web offers them into their own hands and create products that take maximum advantage of the medium. It is key that researches at the forefront become directly involved, otherwise a potential powerful medium will not realize it's true potential, and colorful products with no core content will proliferate. The object of this paper is to outline two ways in which the web can be used to enhance teaching and research objectives."

Jan 1, 2000

By T. S. Krishnan

Among the established permanent magnets, SmCo5 magnet occupies the foremost position as it offers a unique combination of high energy product, coercivity and curie temperature. The SmCo5 magnets are thus extensively used for high field applications. These are also best suited for use in environments where high demagnetising field and high temperature are operative. Also, for applications where high performance and miniaturisation are the over-riding considerations, the choice again falls on SmCo 5 magnets. The main deterrent to the widespread use of SmCo5 magnet is its high cost. Both samarium and cobalt metals are high priced, and the magnets prepared from their directly melted alloy are thus naturally very expensive. An alternate process involving calcium reduction of their oxide intermediates has, therefore, been studied and the alloy prepared by this process has been evaluated and found satisfactory for magnet production. The process essentially involves compaction of the charge mix containing samarium oxide, cobalt oxide (or metal) and calcium metal and&apos; reduction of the charge compact at 1000-1300°C in hydrogen atmosphere, followed by water and acid leaching, drying and classification. The calcium reduction process offers three distinct advantages over the conventional melting processes: (i) The oxide intermediates are relatively cheaper and do not pose any handling problems. (ii) The operation temperatures are comparatively lower and hence precise composition control is possible as samarium losses due to volatilisation

Jan 1, 1989

By Qingzhu Li

The adsorption process of Pb2+ from aqueous solutions by spent grains modified with Imol/L NaCI solution was investigated. The effects of solution pH, contact time, adsorbent concentration, initial Pb2+ concentration, particle size on Pb2+removal were also studied. The initial adsorption process was rapid and 90.35% of Pb2+ adsorption occurred within 30 min. The absorption equilibrium was obtained at 4h. When pH was 5.5, Pb2+ concentration in aqueous solutions decreased from the initial content of 20 mg/L to 0.0 I mg/L after 5 hours by application of IOg/L adsorbent at 25?C, Pb2+ removal efficiency reached up to 99.95% and the Pb2+ remaining in aqueous solutions was under China Sanitary Standard for Drinking Water (GB5749-85). Adsorption data fitted well with Lanf+muir and Freundlich models. However,Langmuir isotherm model was better to descnbe Pb- adsorplion than Freundhch model, mdlcatmg that the applicability of monolayer coverage of Pb2+ on the surface of adsorbent.

Jan 1, 2008

By Jason M. Porter, Douglas L. Porter, David L. Olson, Travis W. Koenig, Van S. Blackwood, Brajendra Mishra, Robert D. Mariani

"Traditional alloy theory models have been applied relative to the three solid phases of uranium: alpha (orthorhombic), beta (tetragonal), and mainly gamma (body centered cubic)[l]. The Darken-Gurry and Miedema models, with modifications based on concepts of Waber, Gschneidner, and Brewer have been used to predict the behavior of four types of solutes: 1) Transition associated with alloying in and containment of the uranium fuel 2) Transuranic elements in the uranium 3) Rare earth fragmentation elements (lanthanides) 4) Transition metals and other fragmentation elements. Using these solute map criteria, elemental behavior have been predicted as highly soluble, marginally soluble, or immiscible (intermetallic phase formers) and have been used to compare solute effects during uranium phase transformations. The overlapping of these solute maps are convenient first approximation tools for predicting alloy behavior.IntroductionAn investigation is in progress to determine the role of various solute elements on size and shape of the 'Y phase field range for uranium to optimize the burning and material processing of nuclear fuel is in progress. Traditional alloy theory models based on correlations to elemental electronic and crystal properties are used to predict solubility and micro structural formation. The effectiveness of this model is based on microstructure property correlations. Darken and Gurry, and Miedema models, with modifications based on concepts of Waber, Gschneidner, and Brewer, models have been used to describe solute solubility with respect to uranium based the on correlation between elemental electronic structure and uranium phases. The alpha (orthorhombic), beta (tetragonal), and gamma (body centered cubic) phases have different solubilities for specific alloy additions as a function of temperature. Using the method of Waber, ellipse diagrams classified those solutes that should have broad solubility in the allotropes of uranium[2]. The predictive diagrams are made from four different correlations:"

Jan 1, 2012

By John Anawati

Bauxite residue is an environmentally unfriendly byproduct of alumina manufacturing, produced worldwide in large quantities. This material contains 50– 100 ppm of scandium, a critical material for the production of stronger, weldable, corrosion resistant, and heat tolerant aluminum products. Aircraft manufacturers are particularly interested in Al–Sc alloys because of its ability to form weldable alloys that could potentially reduce aircraft weight by 15–20%. Because of its abundance and low cost, bauxite residue has the potential to be used as an efficient feedstock for valorization processes to recover its scandium content, while in turn degrading this problematic waste. In this project, we developed an efficient process to recover scandium and rare earth elements from a Canadian bauxite residue with high extraction yields, using industrially scalable and economical techniques. The process employs a modified version of sulfuric acid leaching and subsequent impurity removal by selective precipitation. This article outlines the current progress and design rationale in the development and optimization of this innovative and sustainable recovery process.