Search Documents

By I. A. Scott, T. J. Napier-Munn

Size-by-size partition curves for mineral separation in dense-medium cyclones pivot about a single characteristic point. This is defined for stable, non-segregating media by the medium density and the proportion of the medium reporting to the underflow. The pivot point departs from these values for unstable, conventional media. The phenomenon can be represented by an equation with two parameters defining pivot point coordinates and two the Ep value. On the basis of experiments in a 200 mm cyclone using ferrosilicon media, simple regression equations were developed for the separation parameters in terms of operating conditions (the coefficients were likely to be site-specific). The experiments successfully decoupled the effects of medium density and viscosity and showed that the value of Ep was independent of the former but strongly dependent on the latter. A classification model was used to predict the density of the underflow medium, a knowledge of which is required to determine the pivot parameters. The model correctly reflects the performance trends observed in dense-medium cyclone operation and has the potential to be generalised to a wide range of industrial practice.

Jan 8, 1992

By Z Hu

The technique of reclaiming disturbed land by use of a hydraulic dredge pump (HDP) (which is a set of hydraulic machines for earthwork), termed 'digging deep to fill shallow has been used in the reclamation of subsidence areas in Chinese coal mines. This paper discusses the operational principle of the technique and summarises its reclamation procedures, which are being used in current reclamation practice. The soil condition reclaimed by the HDP was studied. The results showed that the pioneer crops to be planted in the reclaimed soil should be the ‘pulse’ family crops, and that improvements to the reclaimed soil and the HDP technique itself are needed. Bused on the analysis of the previous technical processes, a new rational technical model for the HDP reclamation method is presented in this paper.

Jan 4, 1996

By M. J. Howes

The high degree of mechanisation, which is mainly diesel-powered, has a significant effect on heat loads; heat output from this source often exceeds the heat flow from the surrounding rock. The extensive use of diesel-powered equipment also influences ventilation rates and minimum values are necessary to ensure that emissions of diesel exhaust are adequately diluted. Many Australian mines are in subtropical or tropical areas with high ambient wet- and dry-bulb temperatures on surface. This, coupled with the large amount of heat from mechanisation, usually means that refrigeration is required at much shallower depths. A secondary problem is associated with the definition of acceptable thermal environment conditions, which are sometimes based on the assumption of no air movement. This gives rise to very stringent thermal environment acceptance criteria, which, in some areas, would prohibit work on surface, let alone underground

Jun 12, 1905

By Simons W.

The object of the paper is to describe the standards of quality that should be specified in ordering material ordinarily required for colliery use, and also the qualities most suitable for particular purposes. Tables are presented of British Standard tests for wrought iron grades A, B and C, Admiralty tests for iron in chain, the quality of material for wheels and axles, and the composition and mechanical properties of wrought iron, Armco (ingot) iron and drawbar-gear steel. (Paper presented at the North Staffordshire Institute of Mining and Mechanical Engineers' general meeting held in Stoke-on-Trent, March 27th 1916, Mr. John Gregory, President, in the chair)

Dec 1, 1916

By D. G. Skinner, M. SC. Griffiths

"The natural difficulties associated with the size evaluation of dusts render absolute measurement difficult, or indeed, impossible. Assuming that the desirability of gravi­ metric sampling be conceded, it appears likely tha,t the most suitable means available for physical evaluation are the method of total turbidity measurement, to give a con­ ventional value for specific surface, together with microscopical examination, the great merit of the latter being that in the hands of an experienced operator, semi-quantitative discrimination between coal and other particles is possible.The pipette method, as modified by Fryer, probably-deserves more attention than it has received up to the present. Whatever method is used, it is recommended that in view of the lack of medical knowledge, as much information as possible should be obtained with reference to the total mass concentration, the surface area of the total dust,' and the mass and area of the particles below 5μ in size."

Jan 1, 1947

By A. L. W. Lips, B. P. J. Stevens, T. J. R. Barclay, E. Rothery, S. H. White

Discussion by B.P.J. Stevens of the paper, published in Trans. IMMA, vol.104, 1995, p.B1-B17, is presented together with the authors' response. Stevens questions the authors' radically different interpretation of the structural geology of the Broken Hill Block, considering that the descriptive part of the paper is a useful addition but that the conclusions are unwarranted on the basis of the data presented. A number of major points of disagreement are outlined and half a dozen additional minor points listed. In response, the authors admire Stevens's contribution to unravelling the geology of the area but defend their attempts to take the regional studies a step further, pointing out that he has misquoted what they wrote and arguing that because of the assumptions underpinning the derivation of the present stratigraphy it cannot be used to constrain structural models. With regard to shear zones, they cite the extensive earlier literature and refer to horizontal displacements shown on maps produced by Stevens et al. Detailed discussion follows of the stratigraphy and of the stratigraphic correlation problems resulting from failure to recognise the presence and significance of shears, particularly those parallel to stratigraphy. The remobilised position of the Pb mineralisation in the North Mine open cut is reiterated. It is concluded that there is an urgent need for systematic isotopic dating in the area to constrain the stratigraphy

Apr 1, 1996

By D. W. Holliday

The major deposits of anhydrite and secondary gypsum in Jamaica occur discontinuously at a single horizon within the Lower Eocene succession of southeast Jamaica. They are not intruded from other horizons of different age, as has previously been supposed. The gypsum and anhydrite occur in a regressive sequence at the junction between marine (Richmond Formation, Halberstadt Volcanics, Halberstadt Limestone) and overlying non-marine (Wagwater Formation) sediments. They are thought to have been formed in an arid supratidal (sabkha) environment. A variety of 'nodular' structures occurs in the gypsum and anhydrite which can be related to early diagenetic processes and compaction effects. All gradations exist between single isolated anhydrite nodules and structureless anhydrite due to closer packing and coalescence of nodules. The structures and textures in the anhydrite are thought to be consistent with penecontemporaneous formation from gypsum crystals rarely more than 2 cm in diameter. Single anhydrite nodules are not usually larger than 2 cm; nodules of greater size are compound, due to the coalescence of several smaller nodules. Some large compound nodules may have developed from single sand crystals or rosettes. Compaction of anhydrite appears to have been largely mechanical, but some rocks have an aligned fabric, suggesting later flowage

Dec 1, 1971

By I. R. Hanby

A simple but comprehensive method has been developed for the simulation of a mechanical-drive dump truck that enables various parameters to be predicted as a function of time throughout its whole cycle. Uses of the simulation results are indicated with specific attention to environmental and operational or economic planning. The output of a sample run is presented. The method can be easily adapted for the investigation of a wide variety of mobile plants.

Jan 4, 1992

"The Archaean komatiite-associated nickel sulphide deposits at Kambalda, Western Australia, exhibit a number of stratigraphic features that are indicative of a strong volcanic control on ore localization, including (1) a restriction to specific basal cumulate metakomatiite host units, (2) confinement within distinctive synvolcanic embayments in the footwall and (3) variations in the internal structure and composition of overlying and adjacent barren metakomatiite flow's and the distribution of interflow metasediments with proximity to the ore zones.The high magnesium content of the host units (up to 45% MgO volatile-free) in comparison with that of aphyric or spinifex- textured lavas (16-32% MgO) has been considered previously to indicate either magmas/lavas rich in intratelluric olivine or selective accumulation of olivine phenocrysts. The marked linear trend of the oreshoots, basal host units, footwall embayments and the volcanic stratigraphic relationships have been used as evidence for local linear feeding fissures. Rare relict igneous olivine in some host units is, however, demonstrably not intratelluric, and there is no direct or indirect evidence of a proximal eruptive site (e.g. footwall feeders, pyroclastic breccias, ultramafic intrusives) at Kambalda such as at some other deposits of this type. Kambalda is interpreted as a distal rather than proximal volcanic environment.Emplacement of the komatiite sequence at Kambalda was probably controlled by the locations of a few specific eruptive sites relative to regional topographic gradients and influenced by the topography of the pre-existing volcanic surface. Olivine enrichment in the basal host units occurred by in-situ fractionation and cumulus crystallization of olivine during longitudinal lava flow within linear lava conduits, possibly centralized on depressions between non-overlapping footwall basalt flows. The distinctive stratigraphic relationships are attributed to localization of lava conduits along the volcanic pitchline, flanked by more slowly moving parts of the flows. There are analogies with the physical volcanology of Modern basaltic and Proterozoic komatiitic lava flows.A corollary of this model is that the lava conduits thermally eroded and assimilated sulphidic sediments, contributing additional sulphur to sulphur-saturated komatiites or possibly inducing sulphide separation in originally sulphur-undersaturated komatiites. The latter would account for the restriction of ores to linear cumulate komatiite host units (thermally active lava conduits) and the locally mutually exclusive, but stratigraphically equivalent, relationship between the ores and sulphidic metasediments at Kambalda."

Jan 1, 1984

By R. J. Pine

Procedures are described for the application of risk analysis or probabilistic methods to mining geomechanics. The methods are widely applicable to existing mine design models. Detailed examples are given of plane slope failure and of pillar design based on displacement-discontinuity stress modelling and empirical strength assessment. The modelling techniques assessed are the Latin hypercube sampling method, incorporated in a spreadsheet environment, and the general point estimate method (GPEM), programmed in TurboBasic. An example GPEM program listing is included. Both methods are very convenient to use. Probabilistic acceptance criteria for slope stability after Priest and Brown are examined and alternatives are proposed where output distributions of factor of safety are approximately normal or lognormal and output distributions of safety margin are normal. The reliability index is included as a useful measure of variability with proposed acceptance criteria.

Jan 12, 1992

By E. H. Baker

Vapour pressures of sulphur have been measured over the temperature range 340-1039°C by means of boiling-point measurements, an internally heated pressure vessel being employed with argon as the pressure medium. The results are expressed satisfactorily by a four-term pressure-temperature relation. At the cited critical temperature of 1040°C the calculated critical pressure is 204 atm. From the pressure-temperature relation and available thermal data for the vapour, the approximate composition of the saturated vapour in terms of the various molecular species has been derived for the critical point

Dec 1, 1971

By R D. Lama, A Misra

One of the major factors restricting an increase in the productivity of a longwall mine is lower productivity obtained in a development panel. There has been a significant improvement in gate road development, particularly in mines requiring high density roof and rib bolting within 2 m of the face. Advance rates have increased from an average of 3 m to 5 m per shift in 1985 up to an average of 5 m to 10 m per shift in 1991. In mines at shallow depths with reasonably good conditions the increase has not been that significant. Advance rates have increased from an average of 7 m to 12 ni per shift in 1985 to an average of 12 m to 15 m per shift in 1991. Compared to the United States' (US) development rates, these are much lower. Extensive research work has been carried out to minimise cutting, wheeling, support setting time, and to optimise pillar length to achieve maximum advance rates. Pillar optimisation is very important in order to expedite adverse rates. This paper investigates various development rate technologies, both present and future, and optimises pillars to improve these dev elupment rates. Pillar optimisation is based upon time and motion studies conducted at mines in the Illawara region of New' South Wales, Australia, and the basic tools of arithmetic.

Jan 9, 1996

By J. Plant

Stream-sediment sampling undertaken to define the regional geochemistry of northern Scotland is described with particular reference to the errors involved. The region is underlain essentially by Moine schists, Caledonian granites and Old Red Sandstone sediments, which are generally characterized by low geochemical relief. Factors in the secondary environment obscure the relationship between trace-metal concentrations in stream sediments and bedrock geology. Investigation of sampling and sample preparation methods indicates that the -100-mesh material is the optimum size fraction for the regional survey of this area: it provides adequate geochemical contrast: it reduced the incidence of spurious high values in the samples investigated and it is available in amounts which are adequate for all the analyses required. Grinding samples improves precision and reduces the preferential volatilisation of metals coprecipitated with hydrous manganese and iron oxides for the optical emission spectroscopic method used initially. A study of the dispersion of metals in the drainage system of an area of Pb-Ba-Mo mineralisation and an area of U-Pb mineralisation, respectively, indicates that a sampling interval of 1 per 2 km2 based on second- or third-order streams is adequate to define anomalous metal concentrations. Regional variation can also be represented on the same interval. Modifications to the sampling procedure to reduce the effects of the secondary environment are complicated by the primary association of Mn and Fe with mineralisation in the area. The ratio of analytical and sampling error to regional variance shows that procedural precision is adequate to prepare regional geochemical maps of northern Scotland, with the exception of Cr, Cu at low concentrations and Pb.

Dec 1, 1971

By R. W. Ruddle

The present state of knowledge on this subject may briefly be summarized as follows: (1) The copper content of the slag increases with the grade of the matte in contact with it; on the other hand, the proportion of copper lost decreases as the matte grade increases, because as a general rule a smaller volume of slag is produced when a high-grade matte is made. (2) The presence of CaO and MgO in the slag decreases the copper content of the slag, and the presence of ZnO increases it; the presence of A1203 seems to have little effect. The influence of the silicate degree is not yet clarified, but on theoretical grounds it seems likely that the copper content increases with the silicate degree of the slag. (3) High slag viscosity, high magnetite contents and low density difference between matte and slag all tend to increase the copper loss. The volume of slag is also an important factor. (4) The effect of bath temperature on the copper loss is not clear and further investigation of this point is needed. (5) It appears possible to recover a large part of the copper in the slag by adding FeS, CaS and other sulphides

Jan 1, 1953

By John Craw

This paper has formulated the methods, both medical and engineering, for the control of pneumokoniosis in the haematite-mining industry in West Cumberland, but this is only part of a general service to improve the lot of the worker in these mines, to make him a better and happier workman, and to permit him to enjoy his work and leisure in comfort and good health. This organization has now been functioning for more than ten years and the results are indeed heartening, but it is only as a result of constant vigilance from the mining and medical point of view that such a plan can operate efficiently. The human element and its full understanding is by no means the least of the problems.

Jan 1, 1947

By R. W. Schultz

Mineral exploration carried out in Ireland since the mid-1950s has resulted in the discovery of ore deposits that are now in production atTynagh (Pb-Zn-Cu-Ag), Silvermines (Zn-Pb) and nearby Ballynoe (barite), and Gortdrum (Cu-Ag-Hg); a major Zn-Pb deposit at Navan that is now being drilled prior to development; potentially productive deposits at Keel (Zn-Cd-Pb), Ballinalack (Zn-Pb) and Aherlow (Cu-Ag); and a number of interesting prospects, including one of spodumene. Underground exploration of a formerly extensively mined copper deposit at Allihies has outlined new, albeit currently uneconomic, reserves at depth. The copper and pyrite deposits at Avoca have in recent years been re-explored and are now again being worked. Most Irish ore deposits are in the lower half of the Lower Carboniferous succession of limestones and subordinate shales and sandstones, and this stratigraphic zone is being most intensively explored at present. Other geological units under active exploration are Ordovician sediments-volcanics belts, Caledonian granites, and parts of the Old Red Sandstone and Dalradian series. Surface prospecting is made difficult in many places by glacial and other superficial deposits, including peat and alluvium. Geochemical prospecting methods have been outstandingly successful and primarily responsible for most new discoveries. Boulder hunting and outcrop prospecting have proved effective in detailed investigations of geochemically anomalous areas. Some parts of the country have been covered by three separate airborne geophysical surveys, albeit without success so far. The induced polarisation technique, the most widely used ground geophysical method, has contributed to several discoveries. The scope of application of electromagnetic surveys is more restricted than that of induced polarisation, but the method has been effective in a few cases and has contributed to the Tynagh discovery. To date, the resistivity and self-potential methods have found little application. Magnetic surveys are not applicable directly in the search for ore deposits of the various known types, but can be helpful in outlining geological structures in some areas. The gravity method has been used successfully in a survey over the Zn—Pb deposit at Navan ; it has also proved effective in trials over a blind sulphide deposit at Tynagh that cannot be detected with geoelectrical methods. An appendix lists summary descriptions of 15 Irish deposits and occurrences

Dec 1, 1971

By I S. Lowndes, K. Moloney

Diesel powered equipment is currently used extensively in mining and tunnelling operations around the world due to its mobility, flexibility and through selective application to enhance productivity. However, the increased use of diesel equipment has exacerbated the pollutant load (including heat, humidity, exhaust gases and particulates) placed upon the environmental systems of many underground operations. This expansion in the use of diesel equipment has prom pted researchers to evaluate m easure ment and control technology. This paper reviews the recent research conducted in various countries.

Jan 10, 1996

By S K. Das

An intensive investigation into modern roof support technology, including hy draulic and control systems, has been carried out against the perspective of global development and support behaviour on longwall faces across the Indian sub-continent. The wide ranging study examined various types and designs of modern supports used in seams of varying thickness and inclination where caving and stowing were practised. Consideration has been given to structural analysis, support resistance, the various forces acting over and on the powered supports and to support compatibility. The examination of the phy sical parameters has been allied to field experience and, together, have led to the formulation of standard designs for both the powered support structure and structural systems. A realistic mathematical model has been formulated for calculating the capacity of roof support requirements resulting from the actual behaviour of the immediate roof stratum. As a result of the work, it should be possible to readily select the most appropriate type of support sy stem for the conditions and longwall mining method that is to be employed.

Jan 4, 1997

By B. W. Hester

Report of discussion at January, 1971, general meeting (Chairman: M. J. Cahalan, President) of the paper published in Transactions/Section B (Applied Earth Science), vol. 79, May, 1970, pp. B60-B67, and contributed remarks. Comments were made by Taylor J.T.M., James C.H., Lethbridge R.F. and Heath K.C.G.

Dec 1, 1971

By J. V. Wood, P. Davies, J. L. F. Kellie

A new range of wear-resistant materials is being produced by technology that has been used to develop high performance metal-matrix composites. These include steels and aluminium alloys that can be made as sheet, plate, rod or bar. The incorporation of hard, wear-resistant particles in an alloy matrix is achieved by reactive casting, spray deposition and powder metallurgical techniques. For example, large particles of TiC can be homogeneously distributed in steel during casting and the subsequent product can easily be rolled to plate. Similarly, up to 20% alumina particles and SiC can be injected, respectively, into steel and wear-resistant aluminium alloys by spray deposition. The current state of development of the process is reviewed and indications are given of the projected applications of such materials.

Jan 12, 1992