Search Documents

By P. Lauzon, C. Oprea, S. Zhou, G. Oprea, J. Rigby, T. Troczynski

Hydration of basic refractories could occur during storage, drying after installation or in use. In order to assess the hydration resistance of various commercially available magnesia-chrome bricks, hydration tests were performed in steam at 110, 120, 130 and 150°C. The changes of the modulus of elasticity by the impulse excitation method, apparent porosity, air permeability, average pore size and pore size distribution were correlated with the hydration data. Mineralogical and microstructural changes were also studied on selected specimens by XRD and SEM/EDS. The hydration mechanisms were discussed in correlation with the chemical and mineralogical compositions of the experimental bricks, in particular with the nature of the mineralogical phases at the grain boundaries.

Jan 1, 2004

By J. H. Baek, S. Alexandrovskii, D. W. Lee, B. K. Kim

Nano-phase titanium carbide was synthesized by Mg-thermal reduction process using a novel route of Mg-thermal reduction. The processes are based on I) feeding of TiC14+CxC14 x = 1, 2 ) solution into liquid magnesium, 2) Mg-reduction of metal chlorides, 3) TiC formation by the reaction of released Ti and C atoms, and 4) vacuum separation of residual liquid phases of Mg and MgCl2. In this study, the process for titanium carbide production with composition close to stoichiometry and the minimum content of impurities was optimized with the various process parameters such as concentration of initial solution, its feeding rate and reaction temperature, as well as a kinetic study.

Jan 1, 2004

By G. Brooks, M. Hamed, S. Nightingale, K. Coley

The Marangoni effect plays a significant role in slag line corrosion of refractories. Previous experimental studies for various refractory /slag systems and mathematical models are reviewed and show that Marangoni flow is important in slag line corrosion under static conditions. Recent work by the authors is presented which also shows significant slag-line corrosion of MgO refractory in SiO2-CaO-FeOx-MgO slag. The rate of attack of the MgO was marginally slower in the case of slags containing alumina. A semi-empirical model developed by Hrma based on mass transfer control described reasonably well the observed progression of corrosion with time. Further work is proposed to evaluate this model.

Jan 1, 2004

By Sadough vanini Ali

The silicon anisotropic wet chemical etching technique is widely employed for fabricating various microelectromechanical system (MEMS) structures for advantages such as simple etching equipment and its capability to fabricate special microstructures. In this paper, we consider a complete theoretical derivation of the analytical solution based on geometrical and kinetic aspects of step flow on any surface and with a mathematical method we derive new equation for calculating the microscopic etch rates of surface atoms for a new range of concentrations and temperatures. Furthermore, a novel equation is presented for the calculation of the microscopic activation energies for some typical surface atoms and a new comparison of activation energies between some atoms is made that divides atoms into three categories. The results demonstrate agreement with the experimental results.

Oct 1, 2011

By O. Kangal, G. Önal, G. Bulut, A. Gül

The recovery of copper and cobalt from the ancient copper slags, located in Küre-Turkey, is investigated. Fayalitic type of ancient copper slags containing 1.41% Cu, 0.53% Co and 53.16% Fe were subject to the experimental study. Magnetic separation, gravity concentration and flotation test were conducted. The results of magnetic separation and gravity concentration were not satisfactory. However, a concentrate containing 9.57% Cu could be produced with 44.7% recovery by flotation. Copper and cobalt that remained in the flotation tailings was recovered by roasting with sulfuric acid followed by hot water leaching. Complete cobalt dissolution was observed in 1 hour of roasting at 150°C and 3:1 acid/slag ratio, whereas the copper recovery was 83%.

Jan 1, 2004

By W. Lo, M. Brothers, G. Oprea, G. Richard, T. Troczynski

Magnesia-chrome and chrome-magnesia are the most used refractories in contact with iron-rich non-ferrous smelting slags. The corrosion by slag always brings chromium oxide into the slag, causing the precipitation of crystalline phases at the process temperature. This secondary effect of the chromium-bearing refractory dissolution was studied in this work, emphasizing the effect of the other chemical components of the slag at various temperatures. The experimental results showed that the presence of chromium and lead contribute, although in different ways, to the formation of complex spinel phases and their precipitation at temperatures in the range of 1250-1400°C. The XRD and SEM/EDS results were discussed for refractory-slag mixes containing 0-20% Cr2O3 and 0-11% PbO.

Jan 1, 2004

By T. Watanabe, M. Nakagawa, K. Kimapong

Lap joint of A5083 aluminum alloy and SS400 steel was produced by Friction Stir Welding (FSW) Process. The effect of welding parameters such as rotational speed, traverse speed and tool dimensions on the mechanical properties and the interface microstructures of the joints were investigated. FSW process could successfully produce the lap joint between A5083 aluminum alloy and SS400 steel. The variations of rotational speed, traverse speed and pin depth of a rotating tool gave rise to various characteristic interfaces of the lap joint and had conspicous influences on the joint properties. The increase in hard and brittle intermetallic phase and defects formed at the interface of the joint decreased the mechanical properties such as the shear load of the joint.

Jan 1, 2004

By R. W. McConnell, R. P. Racher

High quality steel production requires extended treatment of the steel in the steel ladle. This has a remarkable impact on the steel ladle refractories, e.g. the need for high performance functional refractories like purging plugs. Operational changes such as increasing tapping temperatures, longer hold times and more aggressive secondary metallurgy are countered by the need for thinner refractory linings and longer refractories life. These combined factors have led to a resurgence in interest in magnesium aluminate spinel raw materials. Magnesium aluminate spinels have been used in steel-making refractories for many years, in a variety of different forms. This paper reviews the production, properties and performance of spinels. Recent developments in the applications of spinels will also be discussed.

Jan 1, 2004

By M. Özer, F. Boylu, G. Önal

In this study, the fine coal waste subjected to the experiments is taken from the waste stockpile of Soma Coal Plant. The possibilities of its evaluation and the production of clean coal were investigated. For this purpose, Reichert Coal Spiral and Shaking Table are used. The minus 1 mm coal waste includes 60.43% ash and 50% minus 38 micron material by weight. The microscopic observations of the screen fractions were shown that the clay minerals are in fine sizes and the coarser size fractions contain silica and carbonate minerals as ash forming materials. The tests were conducted after desliming. The commercial grade clean coal product containing 29-35% ash with a calorific value of 3800-4200 kcal/kg (15.91-17.58 MJ/kg) was obtained by gravity methods.

Jan 1, 2004

By S. Theobald

Semi-finished copper and copper-alloy products are typically produced by casting, subsequent hot rolling or extruding and further cold working by rolling and drawing. The technological properties of the products depend not only on the chemical composition of the alloys but also on process parameters such as annealing conditions and degree of deformation. In each production step, measuring and control technology is an important tool for optimizing processes and ensuring constant high quality. This paper follows the product all the way from testing incoming scrap packages, chemical analysis of melts, mould level control in casting, non-destructive testing technologies in cold forming processes, controlling geometrical properties in the production process, to the final tests of technological properties. All test methods are focused on the applications and requirements of our customers, as the examples show.

Jan 1, 2007

By M. X. Yao, C. D. Opris, P. C. Patnaik, R. Liu, X. J. Wu

Two cobalt-based superalloys, Stellite 694 and Stellite 712, were functionally graded with reinforcement of titanium-carbide particle for high-temperature wear/corrosion applications. The designed composite specimens were fabricated using powder metallurgy (P/M) technique, combined with hot isostatic pressing (HIP). Calorimetric effects of the alloy powders were investigated using the differential scanning calorimetry (DSC) technique, which provided the basis of the sintering cycles designed. The phases present in the microstructures of the materials were analyzed using SEM and X-ray diffraction. The wear resistance of the materials was evaluated on a pin-on-disc tribometer. It was demonstrated that adding titanium-carbide particles to the alloys has increased significantly their wear resistance. It was also found that the HIP process had improved the density of the sintered specimens and thus enhanced their wear resistance.

Jan 1, 2004

By S. K. Sadrnezhaad, B. Hashemi, Z. A. Nemati, Z. Moghimi

Based on the kinetics relationships of a solid - gas model, a software was developed for the prediction of oxidation. Preliminary prediction of oxidation by the software and experimental results of MgO-C refractories were studied and compared. By using the obtained data from this approach, the effective diffusion coefficient, intermolecular diffusion coefficient and diffusion activation energy in the MgO-C refractories, containing various amount of graphite were obtained at different temperatures. First of all, the prediction by the software was very compatible with experimental results, for different oxidation mechanisms in the MgO-C refractories. The results showed that pore diffusion is the predominant oxidation mechanism in this system. The results indicated that when graphite content was above 10wt%, the intermolecular diffusion coefficient was independent from graphite content, and it was closed to a constant value at each temperature.

Jan 1, 2004

By D. Harris, G. Ye, G. Oprea, J. Rigby, T. Troczynski

Sintering and ceramic bonding in refractory castables take place mainly in the binding system during the first heat-up and in service. Consequently the strength and the corrosion resistance of the hot face layer depend on the sintering ability of the complex mix of ceramic powders constituting the binding system. As a result, the use of nano- sized reactive powders in the binding system mixes would activate the sintering and enhance the ceramic matrix formation at temperatures below 1300°C. Our work presents the experimental data on sintering behavior of binding systems containing magnesium aluminate and alumina nano-powders in the temperature range of 800-1450°C. The results indicated that a ceramic matrix, similar to high temperature fired bricks, could be generated after firing at the relatively low temperatures available in the non-ferrous smelting furnaces.

Jan 1, 2004

By D. G. Dixon

A novel technology for leaching copper from primary copper concentrates has been developed at UBC. This patented technology takes advantage of the galvanic couple between pyrite and chalcopyrite to ensure rapid and complete oxidation of chalcopyrite under mild conditions in acidic iron sulfate solution, without the need for microbes, ultrafine grinding, or chemical additives such as chloride, nitrate, or surfactants. Copper recoveries of 98% or greater can be achieved at 80°C under atmospheric conditions in as little as 4 hours of residence time. The process is selective for chalcopyrite over pyrite, generates near-quantitative levels of elemental sulfur, and is fully compatible with conventional solvent extraction and electrowinning of LME Grade A copper cathodes. In this paper, the fundamentals of the Galvanox ? process are reviewed, and selected results of batch leaching tests on various concentrate samples are presented and discussed.

Jan 1, 2007

By T. Hartmann

The presence of crud represents a permanent challenge for solvent extraction in the hydro-metal industry. The crud is a stable emulsion which slowly spreads along the phase boundary between the aqueous and organic phase. The crud can significantly impair the efficiency of hydro-metal extraction because the phase boundary between the aqueous and organic phases assumes substantial proportions, and the settlers cannot react flexibly. In a chain reaction, all settlers connected in series become infected with crud. The transfer of organic phase to the electrowining (EW) cell can cause 'cathode burn'. Continuous treatment of the crud is extremely effective and reliable with a 3-phase separating solid bowl centrifuge. All three phases are separated distinctly from one another. All associated process steps exhibit a steady uniform efficiency. First and foremost, they ensure a reliable, continuous extraction process and, second, they recover valuable re-usable organics from the crud.

Jan 1, 2007

By Xiao Huang, Jean-Francois Thibault, Ali Merati, Prakash C. Patnaik

Single-crystal nickel-based superalloys are the current state-of-the-art technology for the manufacture of turbine blades. This technological improvement of the turbine blade has brought a considerable increase in its cost. Repair and overhaul of service stressed single crystal turbine components is an economic necessity for life cycle cost reduction of engines since the cost associated with replacement is significantly higher than its counterpart polycrystalline component. This paper will first review the recently reported research in developing repair technologies used for DS and SX components. These techniques repair the crack or defect while at the same time ensuring that the mechanical properties do not deteriorate and, more importantly, that the single-crystal microstructure is not jeopardized. It will then be followed by a brief overview of the research conducted and initiated by the authors with regards to the repair of single crystal alloys.

Jan 1, 2004

"At the May 15, 2006 and the May 1, 2007 Canadian Securities Administrators (CSA) Canadian Institute of Mining, Metallurgy and Petroleum (CIM) meetings in Vancouver and Montreal, CSA requested CIM consider certain issues arising out of the CSA review of Technical Reports and public disclosure, in general, regarding the practice of estimation and reporting of Mineral Resources and Mineral Reserves. The following is a summary of the issues raised by the CSA and the responses of the CIM.Preamble: At the May 15, 2006 and the May 1, 2007 Canadian Securities Administrators (CSA)-Canadian Institute of Mining, Metallurgy and Petroleum (CIM) meetings in Vancouver and Montreal, CSA requested CIM consider certain issues arising out of the CSA review of Technical Reports and public disclosure, in general, regarding the practice of estimation and reporting of Mineral Resources and Mineral Reserves. The following is a summary of the issues raised by the CSA and the responses of the CIM Reserve Definition and the CIM Estimation Best Practices Committees (the Committees). This information is intended to provide the Qualified Person (QP) with further guidance when estimating Mineral Resources and Mineral Reserves and in preparing a technical report written under National Instrument 43-101 (NI 43-101). Several members of the CIM Reserve Definition Committee, the CIM Estimation Best Practices Committee and some members of the Committee for Mineral Resources International Reporting Standards have reviewed these issues and provide the following commentary.Issue 1. - CSA requested CIM review and comment on the selection of an appropriate commodity price to be used in Mineral Resources and Mineral Reserves estimates.Commodity prices are used in the estimation of Mineral Resources and Mineral Reserves and in the economic analysis of a property. In times of rapidly changing commodity prices, or when prices are at the extreme ends of a commodity price cycle, the QP has a difficult job in selecting an appropriate commodity price.• The selection of appropriate technical variables, including commodity price, is clearly the responsibility of the Qualified Person (QP). The QP must describe the reasons for selecting these variables, including price, in the technical report.• The definition of a ""Mineral Resource"" contains the wording ""reasonable prospects for economic extraction,"" therefore, a QP must select economic parameters, including commodity price, that will result in an estimate of Mineral Resources and Mineral Reserves that have ""reasonable prospects for economic extraction""."

Jan 1, 2003

By Q. Dong, S. A. Nightingale

An investigation has been carried out to assess the effects of an applied voltage on the dissolution rate of MgO refractory in a steelmaking like slag. In this study corrosion results obtained from dip tests using a dense direct bonded MgO refractory in a CaO-SiO2-Fe2O3-FeO-MgO slag are presented. These results demonstrate that the application of a voltage across a dense MgO refractory-slag interface can change the rate of refractory dissolution. For the slag composition used and the voltage range tested, it was found that a maximum corrosion rate was obtained at a voltage setting of -0.45V. The results of this investigation have been explained in terms of voltage affects on Marangoni (interfacial tension induced) stirring and its effect on the MgO dissolution reaction that is at least partly controlled by mass transfer in the slag.

Jan 1, 2004

By J. Moyes

The Intec Copper Process is an internationally patented hydrometallurgical process for the extraction of pure copper and precious metals from sulfide concentrates. Developed and proven in Sydney, Australia at a cost of US$15m over the last ten years, the Intec Copper Process is now ready for commercial application. The Intec Copper Process has several notable advantages over both smelting and other hydrometallurgical processes. Starting from a base of substantially lower capital and operating costs than any other conventional or developing process, the Intec Copper Process is economically viable at capacity levels as low as 15,000tpa-Cu, and capable of accepting low grade and metallurgically complex concentrates. Precious metals are recovered within the Intec Copper Process circuit, without the need to re-treatment of the environmentally stable solid residues. The Intec Copper Process offers the lowest energy consumption of the available technologies, with no liquid emissions or production of noxious gases. Unlike smelting, sulfur is recovered in the solid residues in elemental form.

May 1, 2002

By L. V. Volkov

The equilibrium of the CuO-Cu20-Cu+-Cu2+ system with various chloride ion concentrations in solution in the presence or absence of an oxidant was investigated. It is shown, that, regardless of the presence or absence of chloride ions or oxidant (oxygen) in the system, the process can be divided into three stages, which are characterized by differing rates and mechanisms of metallic copper cementation and cuprite precipitation and, hence, lead to differing rates of the dissolution of nickel into solution. The effect of the concentrations of chloride ion and oxidant on the phases in the process residues is also discussed. The addition of an oxidant increases the amount of cuprite (Cu20) in the leach residue. With increasing chloride ion concentrations, the rate of copper cementation increases, even without an oxidant in solution. The results of these laboratory experiments and the mechanisms developed are consistent with analysis of samples of industrial cement copper obtained from the Severonickel Combine.

Jan 1, 2007