Search Documents

By Randy R. Williams, Brian W. Wilson, George M. Filz, Marina S. W. Li

"Detailed design of an extensive deep mixing (DM) scheme using the Cutter Soil Mixing (CSM) technique was completed for foundation support of mechanically stabilized earth (MSE) walls for Kitimat Liquefied Natural Gas (LNG) at Bish Cove, British Columbia, Canada. The design was based on the provision of soil-cement structures, constructed in highly variable subsurface conditions that consisted of thick deposits of fine-grained soils overlying granular soils, and required to meet project-specific performance criteria, to support the MSE walls. The design, consisting of rectangular CSM panels constructed to form barrettes connecting to a longitudinal wall of continuous CSM panels, was configured to manage the distribution of stresses and strains that could be developed within the soil-cement structure.The results from 2D finite element analyses were used to determine the necessary arrangement and properties of the CSM panels to accommodate localized areas of relatively high shear, tensile and compressive stresses within the soil-cement structure. The relationships between unconfined compressive strength and elastic modulus for fine-grained and granular soil-cement structures obtained from the Bish Cove data were compared with published references and were found to be significantly different in the higher strength range materials.BACKGROUNDDeep Mixing design was completed for the development of the Kitimat LNG Facility located in Bish Cove, British Columbia, for support of two relatively high MSE walls and associated bulk earthwork operations. Deep mixing was necessary to treat the very weak native deposits in-situ to meet project performance requirements and physical constraints without the need for significant excavation and disposal work. The DM design was undertaken on the basis of adoption of the CSM technique for in-situ ground improvement of the native foundation soils which consisted of very soft to soft fine-grained marine deposits and loose to compact sandy silt to silty sand, overlying dense sand and gravel (Fig. 1). The DM area is located immediately upslope of the Bish Cove beach area, and is “L” shaped in plan, approximately 300 m long by approximately 28.8 m wide (parallel to the beach area) and 165 m long by an average width of 21.0 m (perpendicular to the beach area). The depth of the DM ranged from about 5.0 m to 30.7 m with typically 2.0 m embedment into dense granular soils. Details of the design philosophy, including an overview of the DM design and the project background information are presented by Li et al. (2014a). Details of the construction aspects of the Kitimat LNG deep mixing are presented by Wilson et al. (2014)."

Jan 1, 2015

By Bernardo J. Jiménez Vega, Edy L. T. Montalvan PhD

The experience gained during more than 900 Crosshole Sonic Logging (CSL) tests on drilled shafts shows the importance of establishing proper project acceptance and repair protocols. Drilled shaft evaluation is a multidisciplinary task that should not be left solely to the outcome of the CSL test. This test allows to characterize and delimit areas of different qualities of concrete, and it is important that all the interested parties understand the difference between flaws and defects. The information presented here is intended to give a guideline to contractors, inspectors, engineers, owners and clients on how to deal with acceptance and remediation of defective drilled shafts, detected using CSL tests. A database of flaws is presented depending on their location, intensity and remediation method. Procedures that allow the flaws to be analyzed are presented in order to dismiss or classify them as defects. In many cases, the CSL test may indicate an anomaly, but by coring the concrete and analyzing the structural demands and conditions, the flaw can be classified as non-severe. When flaws are classified as defects, their repair will depend on the area where they are located in the drilled shaft pile. In this document two procedures are described for repairing defects depending on their location. For defects in the drilled shaft head area, the procedure takes into account the interaction between the new and old concrete. For repairing the middle zone of the drilled shaft by grouting, the major concerns are the difficulty of accessing through the drilled shaft at deep depths and the communication between boreholes. For defects at the drilled shaft tip, two proposed remediation methods are presented. Finally, tomography tests are presented to compare the effectiveness of remediation by grouting.

Oct 1, 2022

By Chu E. Ho, Paul Napoli

A new waterfront park was developed on Long Island in close proximity to the East River and Newtown Creek. The existing ground consisted of fill over soft organic clay, medium dense silty sand, glacial till and schist bedrock. The ground was initially raised to preload the underlying soft soils to stabilize the ground in preparation for site development. The ground was subsequently cut down to temporary grades for installation of foundation piles for the overlook structures and construction of reinforced concrete cantilever retaining walls forming pathways located adjacent to the water bodies. The retaining walls were located in two rows at different elevations along the sides of a steep embankment. Where the pathways converge, some of the walls were too close to each other, and were redesigned as a combined U-wall with a common base slab. The individual retaining walls were designed for adequate bearing, sliding and overturning resistance. Ground anchors were installed to enhance global stability of the retaining walls. This paper presents the design considerations for the retaining walls for various loading conditions, and evaluation of the trial and proof tests for the anchors. INTRODUCTION The New York City Master Plan included the transformation of an approximately 30-acre parcel of land in Long Island City, Queens, New York from a former manufacturing zone into a residential, commercial and recreational zone for middle-income community. The site was located at Hunters Point South along the eastern shoreline of the East River and Newtown Creek (Figure 1). The development included low to high- rise residential buildings, a public school, and retail structures. Open spaces were provided along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community-related activities. Waterfront structures included small park buildings, walkways and viewing platforms. The shoreline was surrounded by revetments as part of the flood mitigation strategy. The project involved extensive site re-grading and several retaining walls were constructed. The earthwork volume amounted to approximately 47,000 cubic yard of imported fill and 93,000 cubic yard of cut. The exposed height of the retaining walls ranged from 3 to 15 feet. This paper focuses on the design and construction of the retaining walls for the project.

Jan 1, 2019

By Bernardo J. Jiménez Vega, Edy L. T. Montalvan

During the last phase of the Circunvalacion Norte project in San Jose, Costa Rica, preliminary designs for an underpass structure of over 16 km (10 miles) considered drilled shafts as an earth retaining system. Since the project’s execution was delayed and close to the deadline, it was necessary to optimize this structure, with the drilled shafts being the most critical aspect. The key element in order to obtain an improved design was characterizing the job site with a specific site study for seismic demand, and the use of advanced numerical modelling, considering soil-structure interaction. The site investigation comprised the CPT, PMT, MASW geophysical tests, deep exploration drilling, and triaxial compression tests. The terrain was modeled using an advanced constitutive model with hardening plasticity calibrated from the triaxial tests. Plaxis software was used to calibrate the seismic model for the terrain and for the dynamic analysis. Two conditions were considered for the retaining structure: free-head and fixed head. A parametric study with drilled shafts of 1.0 m (3.3 ft) and 1.2 m (3.9 ft) in diameter, and center-to-center spacing of 1.3 m (4.3 ft) and 3.0 m (9.8 ft) was conducted in order to obtain an optimized structure. For each condition of the drilled shaft wall, the computed deformations were compared for two spectrum designs: site-specific spectrum and seismic code generic spectrum. Finally, a dynamic analysis was performed to check the performance of the drilled shafts with optimized spacing using a control earthquake. Based upon seismic performance curves, the analysis showed the possibility of greater spacing for the drilled shafts compared to the original design, obtaining a 32% reduction in the total length of the drilled shafts in the project.

Oct 1, 2022

By I. D. McPherson, Dominic P. Mahoney

The Metro Sports Facility is currently under development in Christchurch, New Zealand and is a key Anchor Project in the city’s post-earth quake recovery. When completed it will be largest indoor sports and swimming pool complex in New Zealand, with a building footprint in the order of 22,000m2. The site is underlain by poor performing soils comprising interbedded layers of soft compressible silts and loose liquefiable sands to over 20m depth. The site is typical for Christchurch with a shallow groundwater table and artesian conditions. The site performed poorly during the 2010-2011 Canterbury Earthquake Sequence with extensive liquefaction, and associated ground damage. To provide a resilient and economical foundation system for this key development project, deep ground improvement comprising of a uniform grid of some 7,200 stone columns in conjunction with robust shallow foundations has been adopted. This paper discusses the geotechnical site constraints, and ground performance under earthquake loading and describes the various options considered for the development. The foundation option selected, the design considerations of the adopted stone column ground improvement, and foundation solution are described in detail, as well as, construction observations. The paper aims to provide insight into an urban large-scale ground improvement project for the engineering practitioner.

Nov 1, 2022

By Michael T. Lambert

The purpose of the this paper is to demonstrate the benefits of using additional instrumentation during load tests of auger-cast-in-place piles. Traditionally, only load and butt displacement are determined during load tests. The results from and methods used to instrument 15 auger-cast-in-place (ACEP) piles as part of six projects are included herein. By instrumenting the piles, the distribution of load along the pile length and load transfer can be determined, allowing the pile capacity to be adjusted or the length/diameter of the pile to be adjusted for the a given required load. The majority of the piles tested were designed as end bearing piles on either shale or limestone bedrock. No discussion of Geotechnical Instrumentation can be started without acknowledgement of the "Red Book." The actual title of the book is Geotechnical Instrumentation for Monitoring Field Performance, by Mr. John Dunnicliff, John Wiley and Sons, 1993. Anyone undertaking an instrumentation program should thoroughly review the Red Book, paying particular attention to Chapters 3 and 4. Instrumentation should not be done just because it can be done. There must be an unanswered question or questions that can be answered with measured data before instrumentation should be considered.

Jan 1, 2000

By Chang-Yu Ou, Shao-Chi Chien, Hsuan-Hsiang Chang

"A field test was performed to investigate the applicability of electroosmosis with the injection of saline solution of Taipei silty clay. The calcium chloride solution and sodium silicate solution were used as the saline solution for the injection in this test. The results of this study indicate that injection using calcium chloride solution and sodium silicate solution during the electroosmosis to increase drained water from cathode and electro-chemical reaction can greatly improve the effect of electroosmosis and shorten the time of treatment. The results of field vane tests showed that the undrained shear strength after treatment increased an average of approximately 120% for a treatment period of 24 days.INTRODUCTIONThe first field application of electroosmosis in soil was demonstrated by Casagrande in 1939. Since then, more complete field applications of electroosmosis such as Bjerrum (1967), Fetzer (1967), and Lo et al. (1991b) have been made.The results of field electroosmotic work for a period of 120 days were presented by Bjerrum et al. ( 1967). The mean undrained shear strength, Su, increased from 18 to about 40 kPa, with a uniform surface settlement of about 0.5 m. Lo et al. (1991b), with a more sophisticated installation and a relatively larger spacing, also had positive results. For a 3 m electrode spacing during the treatment of a period of 33 days, the mean Su increased from 18 to about 25 kPa. Although the effect of the electroosmosis could be applied in the field based on the above examples, the response remained slow. For actual field work, the application of electroosmosis will be limited due to short project schedules and request of the effect of improvement."

Jan 1, 2005

By Scott White, Pishun Tantivangphaisal, Andrew Bell, Chris Barker

There has been considerable advancement in recent years in the tools, both software and hardware, available to allow efficient digitalization of site records during the construction of geotechnical works. Whilst these tools have excelled at replacing handwritten records, the ability to use digital records to validate design and construction requirements in real time or even within reasonable timescales has generally been limited to the development of bespoke ‘prototype’ project specific solutions. This paper describes the development and implementation of an industry standard design schedule and the benefits of the broad adoption of a single database schema for data recorded on geotechnical sites. The former has brought significant improvements and automation of the design process, whilst the latter has enabled the validation of the constructed works against design intent in almost real time. Further details of the standardized design schedule, already publicly available in the UK through the FPS, examples and lessons learnt from implementing digital site record systems on live projects are presented herein. The utilization of cloud computing technology and complex algorithms linking plant/rig instrumentation with design data can further automate construction sites using IoT (Internet of Things) best practices. The authors will share their experience of the recent deployment of a digitalized design-to-construction record system, give recommendations for future development and a call for an industry wide drive to finalize and adopt the AGS Piling data schema.

May 1, 2022

By Andy Boeckmann

Engineers and owners widely recognize the benefits of foundation reuse - cost savings, reduced construction schedules and reduced environmental impacts, among others. Yet for many projects with existing foundations identified as reusable, reuse is an idea that is discussed at length before cold feet prevail. To address this disconnect, Deep Foundations Institute (DFI) formed the Foundation Reuse Task Force in 2021, which intends to promote reuse, leveraging experience among DFI members and collaborating across pertinent committees. Indeed, the task force includes about 40 members drawn from the Subsurface Characterization for Deep Foundations, Sustainability and Testing and Evaluation committees. One of the first orders of business for the task force was to create a database of successful reuse projects, developing short summary documents highlighting the database projects and recruiting reuse-focused presentations for the ITS Money program. Solid progress has been made on each front: the case history database includes 12 cases so far; the first three summary documents were recently published to DFI's website and foundation reuse projects have been well represented among the past year's ITS Money program. The reuse case history summary documents are available at www.dfi.org/foundation-reuse- case-histories; each of the three is also discussed below. The summary documents demonstrate the feasibility and benefits of foundation reuse. The documents are therefore a useful tool for foundation engineers to share with owners, structural engineers and anyone else who may be hesitant to pursue foundation reuse. The task force continues to welcome new members and anyone interested in joining can contact Andy Boeckmann. The task force is also eager to highlight additional reuse success stories. Anyone with case history information to share is also encouraged to contact Boeckmann.

Jul 1, 2022

By Jerold Bishop, Grant Bearss, Aleksey Egorov

"When a shock wave is released in the bottom of a drill hole filled with wet concrete slurry, the result is called an electrohydrodynamic effect, or EHDE. The energy is carried through the fluid with minimal loss because the slurry is an incompressible medium. Repetitive discharges provide a series of energy pulses that compact the soil along the pile shaft and at its base. The process is analogous to repeated applications of low-energy blast densification or to dynamic compaction. In general, the process is not depth dependent. EHDE was identified in the 18th century by an American scientist who observed that a spark between two electrodes placed under water induced a burst of pressure. In 1957, two Russian engineers formulated a process and received a patent for a method of creating a pressure wave by transforming power from an electrical discharge to a mechanical impact. They derived more than 200 applications for technical and industrial processes.In the 1970s, civil engineers at the Engineering and Building Institute in St. Petersburg, Russia, began to look at EHDE to improve the capacity of drilled piles. Early experiments showed that electric discharges in a wet concrete slurry mix could create a pressure wave of up to 26 MPa (3700 psi). Later tests demonstrated that this pressure level could be created in a drilled pile hole. The researchers devised equipment and in the early 1990s began to study pulse technology as applied to drilled piles.This application was accepted into the Russian Federation Building Code in the 1990s. The code treats “regular” drilled piles with equivalent bearing area as having roughly half the capacity of a driven pile. However, the code considers drilled piles treated with the EHDE technique a direct “one for one” substitution for driven piles and allows higher values if the capacity is established by static load testing. Hundreds of projects have been completed in Russia using this technology to value engineer drilled pile projects. In several instances, the number of drilled piles installed was fewer than half of the number originally planned for due to the capacity increase that EHDE-treated piles provided.Drilled PilesIn drilled pile construction, the EHDE process creates a mechanical pressure wave that impacts the base and sidewall of a drilled pile shaft. Soft, poorly consolidated or loose soil is compacted by successive pulses of pressure created by electrical discharges. These mechanical impulses are made by inserting a discharge probe into the wet concrete slurry. A discharge across the tip of the probe creates the pulse that travels outward to the sidewall and base of the drilled pile through the incompressible medium of the slurry. The power pack ratings for equipment presently in use are 35 and 50 kJ (kilojoule).Each pressure wave strikes the soil, causing compaction and expanding the hole. Workers apply the pulses until the size of the hole stops increasing. They watch the slurry level during pulsing. When the level quits dropping, further soil compaction in the drill hole sidewalls and base is not possible. After the pulse process is complete, workers insert a rebar cage and the pile is finished.The process does not alter the soil mineralogy. The electrical discharge is internally grounded and does not arc to the sidewalls of the drill hole. Soil is not scorched or altered in any manner; it is only compacted by the pressure wave. This technique has been used in urban areas with no effect on electrical or electronic equipment."

Jan 1, 2009

By Dalia. R. Mohamed, Hisham H. Hafez, Marawan M. Shahien

"Construction activities in major projects that involve deep excavations necessitate the use of vertical walls surrounding the construction site to play an important role as earth retention system. The walls are usually partially penetrating impervious walls which can increase the efficiency of the ground water control system that usually consists of number of partially penetrating wells. The analysis and design of such system requires 3D numerical simulation. The aim of this study is to develop simplified semi-empirical approach to analyze and design such system. The analyzed model is a single well in a square site that is surrounded by impervious walls along the perimeter of the site in an unconfined aquifer. The results of the parametric analysis are presented in this paper aiming to assess and understand the factors that influence dewatering in terms of ground water or drawdown profile surrounding the well. The parametric analysis is carried out using the 3D finite difference software. The parametric analysis comprises with more than 550 cases calculated. The study involved the parameters; well penetration depth, impervious wall penetration depth, size of the construction pit, coefficient of permeability, well yield and well location or distance between well center to impervious wall edge.IntroductionThe presence of groundwater in a site may have impact on the construction processes involved during the course of project construction, especially those projects that involve deep excavations. Deep excavations, especially in urban areas, require the construction of supported walls all around the site perimeter to ensure the stability of the excavation. In most of cases, the constructed walls are relatively impervious. Depending on the ground and site conditions, the walls are not penetrating all the way down through to the bottom of the aquifer and thus the walls are partially penetrating walls. The presence of ground water necessitates the lowering of the groundwater to levels below the bottom of the excavation to ensure working in dry. This paper focuses on groundwater control systems that consist of deep wells inside square areas enclosed by impervious walls partially penetrating unconfined aquifers. The wells are partially penetrating the aquifer, as well. There are many factors or parameters that are related to the configurations of the components of the system that may influence the drawdown of a well in such groundwater control system. This paper is a part of a comprehensive study that aims to development of a simple method for estimating the drawdown of dewatering system of the described configuration. In order to achieve such a major goal, a 3D finite difference model is developed for the problem in hand. A comprehensive parametric analysis was then carried out to investigate the influence of all the parameters on the drawdown of a deep well in such groundwater control system. This paper describes the problem, the model, the parametric analysis including the involved parameters. The paper, then, demonstrate the results of the analysis showing the influence of the studied parameters on the drawdown of a single well."

Jan 1, 2016

By Jack Hayes

The design and construction of deep foundations involve many uncertainties. For the designer there are uncertainties regarding soil and ground water variability, regarding sampling and lab testing, regarding analytical techniques and regarding construction technique. The latter being the uncertainty over which the engineer has least control and which may have the greatest impact on capacity. Foundations with a high design factor of uncertainty can be very costly. Foundations designed with a high factor of uncertainty may have a low factor of safety, which can be even more costly.

Jan 1, 2000

By Helen S. W. Chow, Harry G. Poulos

Most modern buildings involve the construction of a basement, often of several levels, to maximize the floor area ratio. The basement walls are generally designed for excavation retention purposes only, and are infrequently considered as elements which can help to support the structural loads from the superstructure. However, the basement walls can provide substantial stiffness and resistance to structural loads, and may contribute to the overall foundation capacity and stiffness. This paper presents a simplified approach to approximate the overall foundation capacity and stiffness considering the various components of the foundation system, including the foundation piles, the basement floor slab, the basement walls and interaction between each foundation component. The effect of the basement walls in enhancing the foundation stiffness values is examined by reference to the results of finite element analyses which consider a foundation subjected to vertical, horizontal and moment loadings. The approximate approach is found to give results that are adequate for a preliminary assessment of the effects of basement walls on the overall foundation response, without the need for detailed three-dimensional finite element analyses.

Nov 1, 2022

By Burt G. Look, David W. Lacey

"Certification of foundation capacity during the construction phase is often assessed by strength or weathering state descriptors based on visual observations. This case study used the Point Load Index (PLI) test as a quantitative tool in the construction certification of a pile’s design capacity. Construction phase tests were completed on irregular sized rock samples whilst comparable design phase testing was completed on intact rock core samples. Statistical comparisons were made to assess the repeatability between the PLI tests, with best-fit Probability Distribution Functions (PDFs) determined for both datasets. Pronounced differences were observed based on the PDF adopted to characterize the PLI dataset, the consequence of which would be a significant change to the pile’s design capacity. The adoption of the lower quartile value is shown to satisfy both design conservatism and construction simplicity requirements. The commonly held belief that rock samples produced during socket excavation may be biased towards the higher strength portion of the rock mass, is shown to be invalid for this site. As the central bridge piers were certified using Plate Load Tests (PLTs), the resultant load-settlement relationships were compared with the PLI strength assessments made for similar materials recovered from the adjacent abutment piles.INTRODUCTIONThe upgrade of the Foxwell Road Overpass across the Pacific Motorway in South East Queensland required the duplication of an existing four span bridge structure. The foundations of the new bridge included the installation of 1.2m diameter cast in place (bored) piles at the bridge abutments and 900mm diameter cast in place (bored) piles below a retaining wall to be constructed adjacent to the existing abutment.The site geology was dominated by the Palaeozoic Neranleigh–Fernvale Beds, predominantly comprised of argillite, sandstone and greywacke. Limited soil materials existed at the site, with Extremely Weathered (EW) rock typically encountered within metres of the existing ground surface. The exception to the existence of shallow rock were locations where existing filling of the site had occurred – i.e. approach embankments to existing bridge structure.Capacity of pile sockets is typically assessed onsite by descriptive rock strength or weathering assessment. Such descriptors encompass a wide range of values and lack precision. Due to the subjectivity of such assessment techniques – a factor of 3 is often observed in terms of strength assessment based on one’s interpretation of rock strength descriptors alone – uncertainty on site often occurs regardless of whether a lower bound, average or other characteristic design parameter applies."

Jan 1, 1900

By Alexander Blatt, Franz-Werner Gerressen

Power Point Presetation at DFI 2022

Sep 1, 2022

By Joseph A. Sopko

There has been a trend in recent years in performing the initial formation freezing using liquid nitrogen (LIN) and then converting the system to circulating refrigerated brine. While proponents of this method state it decreases freezing time, it can also be considered an alternative to inadequate refrigeration capacity. This method was used on several small projects in the 1980s. Problems such as broken pipes, frozen brine, and unsafe work conditions caused contractors to re-think the method. This paper discusses these problems and also presents work schedules showing no schedule reduction. In fact, this method can lead to longer time as well as significantly higher costs. BACKGROUND Ground freezing as a method to provide groundwater control and temporary earth support for excavations is completed using a relatively simple process: drilling and installing refrigeration pipes around the perimeter of the excavation and introducing a coolant into these pipes. The coolant extracts heat from the ground, converting the pore water to ice and forming a strong, impermeable material. A typical ground freezing system is illustrated in Fig. 1. SYSTEMS There are two basic types of coolant systems: circulating and direct expansion. The circulating coolant system is made of two separate, closed systems. The medium circulating is the secondary coolant. It is cooled at a central refrigeration plant, circulated through the pipes, and warms as it extracts heat from the ground. It then circulates back to the plant where it is cooled. This coolant is chilled in a heat exchanger by the primary refrigeration system where a compressor system is charged with a refrigeration gas. The heat is ultimately extracted from the ground and expelled into the atmosphere by an evaporative condenser. Secondary coolants are usually a brine or glycol chemical while the primary refrigeration gas is anhydrous ammonia or another commercially available gas.

Jan 1, 2019

By Dino Kartofilis, Rick Deschamps, Giovanni (John) Bonita

"Anew condominium complex in Arlington, Va., presented some formidable constraints. One was the requirement for a permanent retaining wall to support a 48.5-ft (15-m) cut and an existing 16- story building on top of the slope. Another was the adjacent property owners’ refusal to allow tieback anchors to encroach on their property. The General Contractor (GC) proposed an innovative design incorporating vertical concrete load-bearing elements (LBEs) supported by post-tensioned tiedowns. The owner accepted and the project was successfully completed in 2007.The original designer had proposed a system that included a temporary, raked soldier pile and lagging wall and a permanent cantilever retaining wall with a large piled footing. The system was potentially costly and its constructability questionable.The GC then asked for a design-build alternative to reduce costs and enhance the schedule. The first idea was a diaphragm wall with vertically anchored T-sections. However, configuring a crane to excavate perpendicular sections using grab equipment seemed impossible. There were also utilities approximately 25 ft (9 m) from the existing building, two tiered retaining walls down the slope and a large swimming pool at the base. However, the GC was committed to providing a stable bench 20 ft (6 m) wide along the wall alignment to support the crane.The design evolved to single bite panels using diaphragm wall technology, commonly called LBEs, or barrettes, when they carry vertical loads. For this project, 44 LBEs were horizontally spaced at 9 ft (2.75 m) on center, oriented perpendicular to the wall, extending into bedrock and anchored vertically on the upslope side to resist overturning moments. They were essentially large soldier piles that provided both temporary and permanent support of excavation.An unusual formal agreement was established with the GC to complete the work based on pricing, and prior to completion of final design. This arrangement allowed for an exchange of ideas that increased project efficiencies and lowered costs — without the fear that design concepts would be “shopped” to competitors."

Jan 1, 2009

By David P. Sauls

Design-build contract delivery provides unique opportunities for efficiencies in pile foundation design and installation. The Louisiana Department of Transportation and Development (LADOTD) US Highway 90 at Louisiana State Highway 85 (US90/LA85) intersection was contracted under the design-build delivery system, in part to take advantage of these efficiencies. As one of five projects recognized by the Design Build Institute of America (DBIA) when it honored LADOTD as its 2011 Transportation Owner of the Year in the highway/bridges category, the design-build method provided a way for this project to be ?shovel-ready?, which enabled the LADOTD to secure American Recovery and Reinvestment Act (ARRA) funding. This paper describes the benefits this project gleaned from the design-build process, which included synergy, schedule, design and construction efficiencies, and team building. Interlaced with design and construction of precast prestressed concrete (PPC) piling in compressible southern Louisiana soils, the design-build process rapidly translated computations to cost and schedule savings. A robust quality assurance program using Pile Driving Analyzer (PDA) equipment to evaluate pile set-up provided expedited acceptance of bridge bents and advanced construction schedule. Data evaluation includes analyses of PDA data obtained from 1-hour, 24-hour, 7-day, 14-day and 6-month restrikes of the project test pile.

By Seyyed Mehdi Radeghi Mehrjou

The current work investigates the behavior of inclined micropiles under seismic loads. The dynamic finite element method (FEM) was employed. Rayleigh damping was applied to the soil, and elastic beam elements were employed to model the micropiles. The micropile structure was assumed to have one degree of freedom as a column with concentrated mass. The numerical modeling of micropiles was performed to explore the effects of their inclination on their seismic performance within homogeneous soils with uniform stiffness. In addition, the effect of soil stiffness was studied by considering various stiffness in soil depth. The results from the studies have shown significant effects on the dynamic amplification and internal seismic-induced loads of inclined micropiles.

Sep 1, 2022

"Full time inspection of drilled shafts by qualified personnel is a necessary part of construction. Detailed inspection procedures for routine inspection are provided in the Drilled Shaft Inspector’s Manual, published jointly by the DFI and ADSC: the International Association of Drilled Shaft Contractors.The use of NDT methods or other observation methods, such as probes, video camera inspection, remote shaft wall inspection devices or various calipers are not suitable substitutes for routine "topside" construction inspection as described in the Drilled Shaft Inspector’s Manual. However, these NDT and other "remote" or indirect observation methods are valuable alternatives to direct entry of personnel into drilled shaft excavations. They should be considered whenever appropriate to reduce the risks of direct entry of personnel into drilled shaft excavations.As described in the Drilled Shaft Inspector’s Manual, observations made during construction are essential for quality construction of drilled shafts. The shaft depth, diameter, plumbness, bottom conditions, reinforcement, concrete continuity, and bearing conditions are most easily checked during construction. Some of these observation methods include excavation around the shaft for relatively shallow inspection, down-hole inspection for end bearing conditions or rock sockets, and video camera devices for remote inspection. In rare circumstances, a drilled shaft can be extracted for inspection. Before concrete placement, the bottom of the shaft can also be probed by drilling or coring to determine if there are voids or soft zones in the material at the base of the shaft.The Drilled Shaft Inspector’s Manual focuses on traditional "topside" inspection for routine drilled shaft construction."

Jan 1, 2004