Search Documents

By R D. Lama, A Misra

One of the major factors restricting an increase in the productivity of a longwall mine is lower productivity obtained in a development panel. There has been a significant improvement in gate road development, particularly in mines requiring high density roof and rib bolting within 2 m of the face. Advance rates have increased from an average of 3 m to 5 m per shift in 1985 up to an average of 5 m to 10 m per shift in 1991. In mines at shallow depths with reasonably good conditions the increase has not been that significant. Advance rates have increased from an average of 7 m to 12 ni per shift in 1985 to an average of 12 m to 15 m per shift in 1991. Compared to the United States' (US) development rates, these are much lower. Extensive research work has been carried out to minimise cutting, wheeling, support setting time, and to optimise pillar length to achieve maximum advance rates. Pillar optimisation is very important in order to expedite adverse rates. This paper investigates various development rate technologies, both present and future, and optimises pillars to improve these dev elupment rates. Pillar optimisation is based upon time and motion studies conducted at mines in the Illawara region of New' South Wales, Australia, and the basic tools of arithmetic.

Jan 9, 1996

By D. G. Skinner, M. SC. Griffiths

"The natural difficulties associated with the size evaluation of dusts render absolute measurement difficult, or indeed, impossible. Assuming that the desirability of gravi­ metric sampling be conceded, it appears likely tha,t the most suitable means available for physical evaluation are the method of total turbidity measurement, to give a con­ ventional value for specific surface, together with microscopical examination, the great merit of the latter being that in the hands of an experienced operator, semi-quantitative discrimination between coal and other particles is possible.The pipette method, as modified by Fryer, probably-deserves more attention than it has received up to the present. Whatever method is used, it is recommended that in view of the lack of medical knowledge, as much information as possible should be obtained with reference to the total mass concentration, the surface area of the total dust,' and the mass and area of the particles below 5μ in size."

Jan 1, 1947

By A. L. W. Lips, B. P. J. Stevens, T. J. R. Barclay, E. Rothery, S. H. White

Discussion by B.P.J. Stevens of the paper, published in Trans. IMMA, vol.104, 1995, p.B1-B17, is presented together with the authors' response. Stevens questions the authors' radically different interpretation of the structural geology of the Broken Hill Block, considering that the descriptive part of the paper is a useful addition but that the conclusions are unwarranted on the basis of the data presented. A number of major points of disagreement are outlined and half a dozen additional minor points listed. In response, the authors admire Stevens's contribution to unravelling the geology of the area but defend their attempts to take the regional studies a step further, pointing out that he has misquoted what they wrote and arguing that because of the assumptions underpinning the derivation of the present stratigraphy it cannot be used to constrain structural models. With regard to shear zones, they cite the extensive earlier literature and refer to horizontal displacements shown on maps produced by Stevens et al. Detailed discussion follows of the stratigraphy and of the stratigraphic correlation problems resulting from failure to recognise the presence and significance of shears, particularly those parallel to stratigraphy. The remobilised position of the Pb mineralisation in the North Mine open cut is reiterated. It is concluded that there is an urgent need for systematic isotopic dating in the area to constrain the stratigraphy

Apr 1, 1996

By R. J. Pine

Procedures are described for the application of risk analysis or probabilistic methods to mining geomechanics. The methods are widely applicable to existing mine design models. Detailed examples are given of plane slope failure and of pillar design based on displacement-discontinuity stress modelling and empirical strength assessment. The modelling techniques assessed are the Latin hypercube sampling method, incorporated in a spreadsheet environment, and the general point estimate method (GPEM), programmed in TurboBasic. An example GPEM program listing is included. Both methods are very convenient to use. Probabilistic acceptance criteria for slope stability after Priest and Brown are examined and alternatives are proposed where output distributions of factor of safety are approximately normal or lognormal and output distributions of safety margin are normal. The reliability index is included as a useful measure of variability with proposed acceptance criteria.

Jan 12, 1992

By E. H. Baker

Vapour pressures of sulphur have been measured over the temperature range 340-1039°C by means of boiling-point measurements, an internally heated pressure vessel being employed with argon as the pressure medium. The results are expressed satisfactorily by a four-term pressure-temperature relation. At the cited critical temperature of 1040°C the calculated critical pressure is 204 atm. From the pressure-temperature relation and available thermal data for the vapour, the approximate composition of the saturated vapour in terms of the various molecular species has been derived for the critical point

Dec 1, 1971

By R. W. Schultz

Mineral exploration carried out in Ireland since the mid-1950s has resulted in the discovery of ore deposits that are now in production atTynagh (Pb-Zn-Cu-Ag), Silvermines (Zn-Pb) and nearby Ballynoe (barite), and Gortdrum (Cu-Ag-Hg); a major Zn-Pb deposit at Navan that is now being drilled prior to development; potentially productive deposits at Keel (Zn-Cd-Pb), Ballinalack (Zn-Pb) and Aherlow (Cu-Ag); and a number of interesting prospects, including one of spodumene. Underground exploration of a formerly extensively mined copper deposit at Allihies has outlined new, albeit currently uneconomic, reserves at depth. The copper and pyrite deposits at Avoca have in recent years been re-explored and are now again being worked. Most Irish ore deposits are in the lower half of the Lower Carboniferous succession of limestones and subordinate shales and sandstones, and this stratigraphic zone is being most intensively explored at present. Other geological units under active exploration are Ordovician sediments-volcanics belts, Caledonian granites, and parts of the Old Red Sandstone and Dalradian series. Surface prospecting is made difficult in many places by glacial and other superficial deposits, including peat and alluvium. Geochemical prospecting methods have been outstandingly successful and primarily responsible for most new discoveries. Boulder hunting and outcrop prospecting have proved effective in detailed investigations of geochemically anomalous areas. Some parts of the country have been covered by three separate airborne geophysical surveys, albeit without success so far. The induced polarisation technique, the most widely used ground geophysical method, has contributed to several discoveries. The scope of application of electromagnetic surveys is more restricted than that of induced polarisation, but the method has been effective in a few cases and has contributed to the Tynagh discovery. To date, the resistivity and self-potential methods have found little application. Magnetic surveys are not applicable directly in the search for ore deposits of the various known types, but can be helpful in outlining geological structures in some areas. The gravity method has been used successfully in a survey over the Zn—Pb deposit at Navan ; it has also proved effective in trials over a blind sulphide deposit at Tynagh that cannot be detected with geoelectrical methods. An appendix lists summary descriptions of 15 Irish deposits and occurrences

Dec 1, 1971

By J. Plant

Stream-sediment sampling undertaken to define the regional geochemistry of northern Scotland is described with particular reference to the errors involved. The region is underlain essentially by Moine schists, Caledonian granites and Old Red Sandstone sediments, which are generally characterized by low geochemical relief. Factors in the secondary environment obscure the relationship between trace-metal concentrations in stream sediments and bedrock geology. Investigation of sampling and sample preparation methods indicates that the -100-mesh material is the optimum size fraction for the regional survey of this area: it provides adequate geochemical contrast: it reduced the incidence of spurious high values in the samples investigated and it is available in amounts which are adequate for all the analyses required. Grinding samples improves precision and reduces the preferential volatilisation of metals coprecipitated with hydrous manganese and iron oxides for the optical emission spectroscopic method used initially. A study of the dispersion of metals in the drainage system of an area of Pb-Ba-Mo mineralisation and an area of U-Pb mineralisation, respectively, indicates that a sampling interval of 1 per 2 km2 based on second- or third-order streams is adequate to define anomalous metal concentrations. Regional variation can also be represented on the same interval. Modifications to the sampling procedure to reduce the effects of the secondary environment are complicated by the primary association of Mn and Fe with mineralisation in the area. The ratio of analytical and sampling error to regional variance shows that procedural precision is adequate to prepare regional geochemical maps of northern Scotland, with the exception of Cr, Cu at low concentrations and Pb.

Dec 1, 1971

By C. C. Harris

The two best known graphical methods for presenting and comparing comminution data are obtained by linearising the Gates-Gaudin-Schuhmann and the Rosin-Rammler size distribution equations. It is shown that the Gates-Gaudin-Schuhmann equation can cause excessive congestion in the 50 per cent oversize range and that, overall, the Rosin-Rammler is a better procedure. Examples are given

Dec 1, 1971

By John Craw

This paper has formulated the methods, both medical and engineering, for the control of pneumokoniosis in the haematite-mining industry in West Cumberland, but this is only part of a general service to improve the lot of the worker in these mines, to make him a better and happier workman, and to permit him to enjoy his work and leisure in comfort and good health. This organization has now been functioning for more than ten years and the results are indeed heartening, but it is only as a result of constant vigilance from the mining and medical point of view that such a plan can operate efficiently. The human element and its full understanding is by no means the least of the problems.

Jan 1, 1947

By R. J. Bridges

Mining operations on the Witwatersrand are conducted for the most part in rocks of highly quartzitic character. They comprise the following types: Conglomerates, grits, and quartzites, to which on the Far East Rand must be added fine-grained quartzitic shales and shales. In addition, vein quartz occurring as small veins, veinlets and fissure fillings, and igneous rocks forming dykes, must be mentioned, although they constitute only a small percentage of the rock broken. The following is an account of the character and mineralogical composition of the various types.

Jan 1, 1947

By Eric Forssberg, Vigen Zeng

During mechanical grinding high intensity vibration is emitted that contains information on the mill's operating state. Tests, using a laboratory ball mill, studied the influence of operating parameters on the vibration signature. The parameters studied were: mill speed; powder filling; pulp density; grinding period; and pulp temperature. Vibration signals were detected by an accelerometer, amplified by a vibrometer and recorded onto digital audio tape. A digital oscilloscope converted the signals into IBM-compatible data format. Digital signal processing and multivariate data analysis were carried out with specially developed software. The power spectral density was estimated from the time-domain vibration signal. Four new latent variables were used to describe changes in the vibration spectra. A relationship was established between operating parameters and latent variables which could form the basis of a quick and automatic method of monitoring operating parameters in ball mill grinding.

Jan 4, 1993

By L. J. Barnes, R. O. Koch, J. H. Versteegh, C. J. N. Buisman, P. J. H. Scheeren

Several water treatment options have been studied and piloted. A process based on activity of sulphate reducing bacteria combines sulphate removal and heavy metal removal in one process step. The anaerobic bacteria reduce the sulphate to sulphide and consequently metal sulphides will precipitate. The final design for the commercial scale plant is described.

Jan 12, 1992

By B. W. Hester

Report of discussion at January, 1971, general meeting (Chairman: M. J. Cahalan, President) of the paper published in Transactions/Section B (Applied Earth Science), vol. 79, May, 1970, pp. B60-B67, and contributed remarks. Comments were made by Taylor J.T.M., James C.H., Lethbridge R.F. and Heath K.C.G.

Dec 1, 1971

By M. Riddell

This paper describes the incipient heatings that occurred below ground in the High Main and Main seams at the mine between the years 1963 and 1966. The possible causes, effects and activities associated with such heatings are discussed in an attempt to establish the precautions necessary to minimize such occurrences. The assessment of as many "norms" as possible is made to enable the earliest detection and level of activity to be determined.

May 23, 1905

By J. S. WARWICK, E. J. Browning

Ignitions continue to occur underground, sometimes leading to major explosions. There has been considerable effort in the UK, and more widely in the European Community, to formulate the best ventilation practices and other means of minimising these incidents. Practices and procedures to prevent ignitions are discussed in the light of the risks from current mining methods.

Jan 1, 1993

By M. D. Gibbs, T. N. Smith, B. Verbaan

When heated in the absence of oxygen, pyrite from refractory gold concentrates decomposes endothermically to pyrrhotite, releasing sulphur. The decomposition starts at the particle surface and progresses inwards, leaving an adhering layer of porous pyrrhotite. Use of the conventional shrinking-core model implicitly assumes a negligible partial pressure of sulphur in the bed, but this pressure is in fact at least equal to the equilibrium vapour pressure of sulphur over pyrite, constituting the principal control of the rate of decomposition. Further experiments showed a decrease in reaction rate as the conversion increased. Both phenomena are attributed to the persistence of non-isothermal conditions in the fluidised bed during pyrolysis, caused by the endothermic nature of the reaction and the relatively slow rates of heat transfer to particles and vapour removal from the bed. Equipment must be developed to maximise these two parameters

Jun 19, 1905

The Council of the Institution of Mining and Metallurgy submitted the report of the affairs of the Institution for the session 1970-71, and the Statement of Accounts for the year ended 31 December, 1970. The statistics given in the report refer to the calendar year 1970. Details are included of membership, officers, representation on other bodies, honours and distinctions, awards, meetings, publications, library, overseas activities, fellowships and grants, the revenue and expenditure account, the balance sheet, trust fund balances, contributing companies, and schedule of investments

Dec 1, 1971

By T. Piirainen, T. Alapieti

"The Koillismaa layered igneous complex is the result of igneous activity that occurred 2436±5 m.y. ago. Its crystallization took place in three separate but connected magma chambers, the total volume of which is estimated at more than 2000 km'. These chambers were located partly in a feeder system within Archaean granitoids and partly in an unconformity between these grani­ toids and Early Proterozoic supracrustal rocks. The composition of the parental magma that initially filled the chambers is thought to have been that of a relatively MgO-rich tholeiite. Sulphides and platinum-group minerals are mainly concentrated in the marginal series of the western part, where they are encountered over a distance of 25 km. This marginal series is an originally nearly horizontal series of rock types that displays a reversed differentiation trend, grading inwards from gabbroic to ultramafic rocks, followed bv rocks of the layered series. The chilled margin is not encountered anywhere in its original position at the contact, probably as a consequence of magmatic erosion, but remnants are to be found in the form of elongated xenoliths. Partly melted siliceous fragments from gneissic country rock typical of the lower part of the marginal series indicate pronounced contamination.Chalcopyrite, pentlandite and pyrrhotite±pyrite are the predominant sulphides. The accessory sulphide minerals include covellite, violarite, marcasite, mackinawite, sphalerite and argentian pentlandite. Platinum-group minerals are represented by froodite, michenerite, merenskyite and sperrylite. Other accessories that have been identified are electrum and native copper and gold. The mean of the Cu/(Cu+Ni) ratio in the mineralizations is 0.67 and Pt/(Pt+Pd) 0.31.It is suggested that the sulphide phase was formed in the marginal series as the solubility of sulphur in the basic magma was lowered by contamination, possibly assisted by some other factors. The sulphur isotope data support the juvenile origin of the sulphur."

Jan 1, 1984

By M. Rahman, P. C. Kapur

The fixed-time locked-cycle grinding test is employed to simulate the industrial closed grinding circuit on the laboratory scale. A mathematical algorithm for 'cyclewise' computer simulation of the locked-cycle test has been derived and used to study an idealised laboratory-scale model of a closed ball-mill circuit. The agreement between simulated and experimental results is reasonably good, except when the grinding times are relatively long

Dec 1, 1971

By R. R. Liebenberg, M. I. Brittan

The kinetics of the copper segregation process has been investigated. The experimental strategy used to isolate the rate-controlling reaction step is described. This step was found to be the chloridisation of the oxide copper minerals in the ore. The link between the rate of chloridisation and the overall rate of segregation is demonstrated experimentally. The influence on the kinetics of the various parameters in a TORCO system is examined and the implications are discussed

Dec 1, 1971