Search Documents

By Magdalena Regel-Rosocka

Extraction of zinc(II) from hydrochloric acid solutions is discussed. The literature on the extraction of zinc(II) in the presence of iron(III) and iron(II) with various basic and solvating reagents has been reviewed. It was found that tributyl phosphate (TBP) is the best compromise, and permits both effective extraction of zinc(II) and its stripping with water. The process was confirmed in a continuous laboratory mixer-settler circuit.

Jan 1, 2003

By V. A. Bryukvin

A characteristic feature of the macrokinetics of the interaction process is the presence of two specifically defined areas of oxidation which had a linear time dependence. The effect of variables, such as residual sulphur content of the melt, temperature and the oxidation potential of the gas phase, on the macrokinetics of oxidation are investigated. Phase composition and structure of products of solidification of partially oxidised melts and thermodynamic properties pentaining to Cu-S-O melts are used to analyze the macrokinetic behaviour and mechanisms of the interaction. The process of interaction of sulfide copper melts with oxygen may be considered as a disproportional absorption process and its mechanism is based on localized interaction on the surface and inside the melt volume. Superficial processes include also the process of primary chemisorption of oxygen by melts at place of metal-metal donor bonds proceeding with formation of oxysulfide liquid solutions and volumetric decomposition of the latter accompanied by evolution of sulfur dioxide and metallization of sulfide melts. It is the degree of dynamic balance of such interaction processes that determines specific individual features of the macro-kinetics and mechanism of oxidation of sulfide copper solutions with oxygen in the gas phase.

Jan 1, 2006

By Jae-Woo Ahn

Waste acids containing phosphoric, acetic, nitric and hydrofluoric acid were produced during the etching process of liquid crystal display and semiconductor manufacture. In recent years, the attention on the treatment of industrial waste acids has been increased considerably according to the reinforcement of the environmental regulations as well as the implementation of the economic considerations about the waste acids. Fundamental studies on the separation and regeneration of the mixed waste acids were conducted using Cyanex 923, Tri-octyle phosphate and 2-Ethylhexyl alcohol as an extractant by solvent extraction. It is considered that the extraction of liquid crystal display waste acids with Cyanex 923 and Tri-octyle phosphate, semiconductor waste acids with 2-Ethylhexylalcohol is applicable for the separation and recovery of acid. Finally, the acceptable recycling process from the multi-component waste etching acids was proposed.

Jan 1, 2006

By Alim Ullah

Process, quality and management control are necessary in order to produce DRI of required quality and at minimum cost. Although the characteristics of the two (2) principal inputs, that is, iron oxide feed and natural gas (for gas-based DRI plants) can affect the operation of a DRI plant significantly, they are outside the control of plant operators, at least in the short run. The quantity of reduction gas, its composition and reduction gas temperature are some of the key process variables. Statistical Process Control (SPC) can be used in a DRI plant to minimize the production of off-grade material and costs, as well as to improve the overall operation of the plant. One of the key quality variables to be measured and controlled is percent metallization, defined as FeM/FeT*100 where, FeM and FeT respectively are metallic iron and total iron in DRI. Control charts are used to monitor the quality of DRI produced and, when necessary, corrective actions are taken to bring the product back within the control limits. Management control can consist of essentially following how well the plant performs against some pre-established standards of parameters like daily production, downtime, consumption of material and energy, etc. In this respect, it is suggested that yield, defined as theoretical consumption/actual consumption of iron oxide feed, be used to monitor the consumption of feed material. Similarly, instead of using natural gas per ton of DRI produced, a better criterion would be efficiency, defined as theoretical natural gas consumption/actual natural gas consumption.

Jan 1, 2006

By Kang-In Rhee

Nonferrous metal recycling not only provides energy saving and environmental benefits but also is a significant factor in the supply of various types of metals used in our society. Recycling plays an important role in establishing the sustainability of materials. The total amount of recycled nonferrous metals by weight accounts for less than 5% but their value is larger than 50% compared to ferrous metal recycling which consists of about half of the total metal recycling in weight. This paper describes trends and typical achievements in nonferrous metal recycling and overviews the present and future of nonferrous metal recycling technology and business in Korea.

Jan 1, 2006

By M. H. Ghandehari

Sintered (Pr,Sm)Co5 displays a multi-phase microstructure in which closely related intermetallic compounds are formed during the process of fabricating useful magnets from over-stoichiornetric compositions. These compounds have much lower magnetic crystalline anisotropies compared to those of SmCo5 and PrCo5. Despite a careful control of the microstructure in producing "single phase" PrCo5 base magnets, sufficient concentrations of the lower anisotropy phases are formed which act as nucleation centers for domain reversal, resulting in a drop in coercivity. This article describes the use of sintering additives, primarily oxides, to prevent the formation of the magnetically soft phases in the final microstructure.

Jan 1, 1989

By J. G. Peacey, P. Hancock, R. -Q. Li

A pyrometallurgical process for the direct recovery of zinc from zinc concentrates and zinc/iron residues has been proposed and tested extensively by Noranda. The process consists of smelting bone-dry zinc containing materials (sulfide concentrates and secondary zinc/iron materials) in a molten iron oxysulfide bath to volatilize metallic zinc into a SC^-free offgas. Sulfur contained in the feed materials is fixed as an iron oxysulfide matte for disposal. Thus, this process not only is capable of treating zinc sulfide concentrates and secondary zinc materials simultaneously, but also eliminates the need of sulfuric acid production. Detailed thermodynamic analysis and experimental test work are described in this paper.

Jan 1, 2000

By Jesús L. Valenzuela

The solvent extraction for gold from alkaline cyanide solutions has been investigated using LIX 79 guanidine-based extractant. Different variables that could affect the extraction system were evaluated: equilibrium time, aqueous pH and extractant and modifier concentrations. The extraction isotherms of the aurocyanide complex with respect to other cyanoanions were compared and the following order of selectivity Au>Ag>Cu>Zn>>Fe was observed. From the pH isotherms it was found that aurocyanide can be extracted in alkaline media and a better separation with respect to other cyanoaniones was obtained in the range of 10.5 < pH < 11.2. Better selectivity was observed when using LIX 79 and tridecanol at 10% and 5% vol, respectively. Stripping gold from loaded organic was carried out at pH>12, using NaOH and NaCN solutions.

Jan 1, 2003

By E. Gervais

Modern life in inconceivable without zinc. Zinc provides the most cost-effective and environmentally efficient method of protecting steel from corrosion. Zinc is also used to power electric vehicles and computers, to make brass, automotive equipment, household appliances, fittings, tools and toys, and to support the building and construction industries. It is also used in pharmaceuticals and cosmetics, in rubber, in fertilisers and in animal feeds. The links between properties, applications and performance, as well as zinc demand and market dynamics, will be reviewed along with market development opportunities and successes. The presentation will also include a progress report on the five-year plan of the International Zinc Association to increase the global market for zinc, over and above the natural growth, by 500,000 tonnes/year by 2002.

Jan 1, 2000

By Andrew A. Fyfe

The start-up and operating results obtained at Zia Technology Inc.&apos;s first commercial operating facility at Caldwell, Texas are described. The operation which stated in early 1991 is the first to employ the patented Inclined Rotary Reduction System (IRRS&apos;) with the associated &apos;all-metallic retort for the recovery of all metallics contained in EAF dust.

Jan 1, 1992

By G. St-Amant, V. Cloutier, E. Ghali, S. Jin, G. Houlachi

During the casting of lead-silver anodes, variations in cooling rates result in the formation of an uneven microstructure. The slowly cooled areas (SCA) have a coarser microstructure than that of the remaining part (called "the general zone"). The effect of anode microstructure on the electrochemical behavior was investigated using galvanostatic, potentiodynamic and electrochemical impedance techniques. The results show that the resistances for the two steps of the oxygen evolution reaction on the slowly cooled areas of Pb- Ag anodes are higher than that on the general zone. The double layer capacitance for the first step of the oxygen evolution reaction (OER) and the pseudocapacitance of the second step of OER on SCA are smaller than those on the general zone. The potentiodynamic results show that the amount of lead dioxide formed on the SCA is greater than that of the general zone of the anode. The potential decay curves after 30 minutes of galvanostatic polarization at 45 mA/cm2 show that the corrosion potential of the SCA is 200 mV lower than that of the general zone. This can lead to perforation because of the formation of a galvanic cell with a small anode and a large cathode.

Jan 1, 2000

By Peng Fan

Nitride capacity is usually employed as the measure of slag?s ability to remove nitrogen from liquid metal, since nitrogen distribution ratio between slag and metal can be calculated from nitride capacity provided that the value of oxygen activity in liquid metal is available. However, during liquid metal refining processes, oxygen activity in liquid metal is usually unknown and thus it is impossible to get nitrogen distribution ratio from nitride capacity under this usual condition. In this paper, thermodynamic analysis indicates that the activity coefficient of nitride in slag can be used to measure slag?s ability to remove nitrogen from liquid metal, because nitrogen distribution ratio between slag and metal can be calculated from the activity coefficient of nitride in slag provided that the content of oxygen potential controlling element like Al in liquid metal is available. Review of reported nitrogen removal studies and our recent study has verified that for a given Al content in metal, the lower the AlN activity coefficient in slag is, the higher the nitrogen distribution ratio. Titanium monoxide based slag has been found to be much more effective to remove nitrogen than other slags. Since Al content in liquid metal is usually available during liquid metal refining processes, AlN seems to be a better measure of slag?s ability to remove nitrogen from liquid metal.

Jan 1, 2006

By K. S. Jeong

Since the start-up of the Onsan Smelter in 1979, LS-Nikko Copper has grown into a competitive smelter through continuous development. Several environmental improvements have been carried out, in particular, intensive investments in reducing SOx emissions, such as de-sulfurization plants, fugitive gas capturing and TMS(Tele Metering System). In addition, in recent years LS-Nikko Copper has spent more than 10 million USD every year to improve environmental conditions. In order to be a global leading smelter in every aspect especially environmentally, LS-Nikko Copper plans to inspire environment-friendly minds, co-operate with shareholders, and participate in global conventions. This paper describes the environment improvements carried out at Onsan and briefly introduces a sustainable vision for a green smelter.

Jan 1, 2006

By Torben L. Edens

Norddeutsche Affinerie is the largest copper producer in Europe. Two sites are in operation for the production of refined copper: primary copper production is located in Hamburg and secondary copper production in Lünen. A total of just under 560,000 tonnes of copper cathodes is produced annually at the two sites. Primary copper production using the flash smelter furnace has been in operation in Hamburg since 1972. Over the years, the capacity of the flash smelter has been increased in three expansion projects from 120,000 t to almost 500,000 t of anode copper p.a. The anode sector consisting of two anode furnaces and a 24 mould casting wheel still features just about the same equipment as in 1972. The paper describes the most important steps taken to optimise operation which have put NA in a position to cast meanwhile more than 500,000 t of anode copper annually with the two anode furnaces and 24 mould anode casting wheel.

Jan 1, 2006

By T. J. A. Smith

This paper provides an overview of some of the key issues in design of smelter gas handling systems, with particular reference to sulphide smelting plants. In both primary smelting and converting. gas handling and treatment systems often represent the major capital cost component. There is also ample evidence that poor system design can be a major cause of smelter down time, lost production and unforeseen high maintenance costs. The paper discusses these issues and offers guidance for improved design.

Jan 1, 1992

By T. J. A. Smith

This paper provides an overview of some of the key issues in design of smelter gas handling systems, with particular reference to smelter smelting plants. In both primary smelting and converting, gas handling and treatment systems often represent the major capital cost component. There is also ample evidence that poor system design can be a major cause of smelter down time, lost production and unforeseen high maintenance costs. The paper discusses these issues and offers guidance for improved design.

Jan 1, 1992

By Kazutaka Kunii

It is invariably certain that after punching for IC Leadframes, scrap metal were generated. These seraps were re-dissolved and in order to use as raw material for leadframes, it is necessary to remove the Ni plating. In this study a simple method was developed for the removal of Ni plating by surface oxidation of Ni plating. For this purpose a fundamental study was carried out on the oxidation behavior of Ni plating. Results showed that by controlling the oxidation condition, a considerably high rate of Ni could be removed.

Jan 1, 1996

By J. Peter, S. E. James, J. L. Watson

A survey of operating zinc smelters and refineries throughout the world has been done in conjunction with the Lead-Zinc 2000 Symposium. This survey follows the examples set by the Japanese Mining Industry Association in 1985 and 1995. Questionnaires were sent to operating zinc plants that covered feed materials, process details, energy consumption and labor requirements. The voluntary responses to the survey were tabulated. Key operating parameters including feed grade, production capacity, quality of the intermediate products and quality of the final products have been compared for both hydrometallurgical and pyrometallurgical processes.

Jan 1, 2000

By Hiroyuki Sano

Elimination of heavy metals from the incineration fly ash by the chlorination volatilization method had been already developed and the effectiveness of this method was confirmed by the present authors. In this study, this method was applied to the elimination of heavy metals, mainly lead, from the incineration bottom ash. Since the fly ash contains a large amount of chloride, heavy metals in the fly ash are easily chlorinated. On the other hand, the addition of the chlorination agent is a key point for applying this method to the bottom ash, because it hardly contains chloride. The effects of various variables such as a kind of chlorination agent, adding quantity of it and temperature on the elimination ratio were investigated and the harmlessness of the residual ash was evaluated. The preferable condition was proposed from the recyclability of the bottom ash.

Jan 1, 2006

By Giovanni Principi

The activity of the ?Hydrogen Group? of Padova University, addressed to the study of materials for solid state hydrogen storage, is illustrated. Various Mg-based materials have been considered and are being studied: a) MgH2 and 0.5% mol Nb2O5 mixture ball milled under argon atmosphere; b) Mg-Ni-Fe intermetallic compounds prepared by short time ball milling of ribbons obtained by melt spinning and by long time ball milling of a mixture of MgH2, Ni and Fe powders; c) MgH2 ball milled in argon with Mm-Ni-Al (Mm = La-rich mishmetal) and Zr-Cr-Fe catalyst alloys. All the samples have been structurally characterized by X-ray diffraction (Rietveld refinement) before and after hydrogen absorption/desorption cycling and tested with a Sievert apparatus as regarding their thermodynamic and kinetic properties.

Jan 1, 2006