Search Documents

By Hee Dong Jang

Crystalline metal oxide nanoparticles such as lithium cobalt oxide (LiCoO2) and indium tin oxide (ITO) were synthesized from sprayed droplets of aqueous precursor solution by flame spray pyrolysis. Complete thermal decomposition of the aerosol precursors was obtained at high flame temperature. Molar concentrations of the precursor solution, and the flow rate of combustion gas such as hydrogen, oxygen and air were varied to control particle size, size distribution and crystal structure. The crystalline nanoparticles synthesized were nearly spherical, and their average primary particle diameters ranged from 11 to 35 nm for LiCoO2 and from 8 to 15 nm for ITO.

Jan 1, 2006

By Jaeheon Lee

Gold-copper alloys are shown to form during the cementation of gold on copper in a solution containing 0.25M [S2O32-] at 25oC. The alloy composition is strongly dependent on the initial Cu:Au ratio in solution and ranges from Au3Cu to AuCu3. XPS results for Au, Cu, S, and O are reported as a function of depth through an entire deposited film with an initial solution containing 20 ppm [Au] and 30 ppm [Cu]. The deposit contained about 20 atomic % gold and was predominantly Cu3Au. Underpotential deposition (UPD) theory is discussed as a mechanism for explaining the formation of these alloys. Several other systems that produce alloys during contact reduction/cementation are also discussed.

Jan 1, 2003

By F. J. Arriagada

Where gold is present in a finely disseminated form within sulfide particles, the porosity and surface area of the calcined material strongly influence leaching since they control the penetration of solution inside the gold-bearing grains. On the basis of a stability diagram for the Fe-O-S in the temperature range of 400 to 750aC, the expected sequence chemical transformations associated with the oxidation of pyrite is discus-sed. By using analytical techniques which include scanning electron microscopy, X-ray diffraction and BET gas adsorption, the chemical and structural changes experienced by auriferous pyrite-arsenopyrite concentrates and pure pyrite samples are studied under an oxidizing roasting atmosphere of com-position 80% N + 20% O2 in the temperature range of 450 to 750°C. The results indicate that as the roasting temperature increases, the surface area of the calcines decreases sharply after a maximum value attained at about 450-500°C. SEM micrographs show that the needle-shaped tips which characterize the surface of the oxide product become wider and the size of the pores between them is decreased when the roasting temperature is in-creased from 550 to 750°C. This effect suggests that the formation of a more "closed" hematite product at higher temperatures is due to sintering associated with a faster growth and crystallization of the oxide. A strong correlation is shown between increasing roasting temperature and increase in gold lost in cyanidation tailings, an effect which may be partly attributed to the loss in surface area of the calcines.

Jan 1, 1982

By Suzzann Nordwick

Over the past decade, significant advances have been made in the development of sulfate-reducing bacteria (SRB) technology to treat acid mine drainage (AMD). Bench-scale testing, field demonstrations, and engineered applications of SRBs for the treatment of AMD will be presented. Designs include an in situ bioreactor installed in the subsurface workings of the Lilly Orphan Boy Mine in 1994, the SRB bioreactors installed at the Calliope Mine from 1998 to 2001, the integrated biological reactors built at the Surething Mine in 2001, and the ongoing development of a replaceable cartridge system. SRB technology benefits include the reduction of dissolved metal ions to insoluble metal sulfides and the neutralization of the AMD resulting from the production of bicarbonate from the oxidation of organic nutrients. This paper will address engineering design criteria including the selection of organic media and system permeability and complete mitigation of AMD. Research was funded under Interagency Agreement No. DW899388-70-01-1 between the US EPA and the US DOE and was conducted by MSE Technology Applications, Inc., through the National Environmental Technology Laboratory (DOE Contract No. DE-AC22-96EW96405) at the Western Environmental Technology Office located in Butte, Montana.

Jan 1, 2003

By Tim Robinson, Michael S. Moats, Masatsugu Moritmitsu, Kathryn C. Sole, Lauri Palmu, Frank K. Crundwell

"Process technology and design trends for copper, zinc, and nickel electrowinning cellhouses include focusing on energy reduction, productivity, and acid mist abatement. Larger electrodes, longer cells, automation, and higher current densities are leading to more capital-effective designs. The latest cellhouse designs include installation of automated electrode-handling systems, thereby removing more operators from the cellhouse. These technology and design trends result in lower electrowinning operating costs and improved purity of electro won cathode.INTRODUCTIONTechnology transfer between similar industries is an important process in improving product quality and productivity, and reducing operating costs. The electrowinning (EW) recovery of base metals, such as zinc, copper and nickel, is no different. The zinc industry with its larger EW product-handling requirements as compared to nickel and copper, has been driven to automation technology and the use of larger equipment. This technology has been transferred to copper. Nickel has led development and application in large-scale anode and divided-cell technologies but, due to nickel being produced in multiple forms (not just cathode) and being a small part of the whole complex nickel process route, the quantities of electrowon nickel are small compared to copper and zinc. Copper process technology in acid mist abatement was recently transferred to nickel. The focus in copper EW has been on energy reduction and productivity."

Jan 1, 2012

By P. S. Seryogin

R & D works supported by industrial-scale tests, which were carried out by joint efforts of the OAO Gipronickel Institute and MMC ?Kola? engineers, have accomplished with the production of 90?95% metallized nickel powder in tube furnaces (NPTF), with its ?active fraction? (AF) to be further used for decopperization of nickel electrolyte by cementation. Consistently positive results obtained in the course of the lab and industrial experiments have allowed the Severonickel Combine management to effectively replace all activated nickel powder (ANP), which was then employed for cementation, with the AF, having activity over 80%, and eventually shut down the entire operation of gaseous reduction. Ever since the developed technology has been implemented, its annual economic effect exceeds 2 ml. dollars.

Jan 1, 2006

By J. R. Parga

A shortage of landfill space and growing environmental concerns in Mexico are renewing interest in the recyclability of scrap from automobiles. This work describes a pyroumetallurgical process for the recovery of metallic lead from waste lead paste. Argentopyrite concentrate is commingled with lead paste residue and smelted in a fuming process thereby transferring the precious metals into lead bullion. The process consists of smelting lead paste and argentopyrite, sodium carbonate, and metallic iron at smelting temperatures of about 1100 T. The reaction products are slag and molten lead bullion enriched with precious metals. A major feature of this process is the removal of precious metals from the bullion by means of zinc, whereby a silver-zinc intermetallic compound is formed and floats out of the lead. The recoveries of precious metals are about 98%.

Jan 1, 1996

By K. Sanjay

Factorial optimisation technique has been used to develop regression equations at different time intervals for extraction of manganese from precipitated manganese oxide/hydroxide in sulphuric acid using charcoal as the reductant. The three parameters chosen for a 23 full factorial design were : acid concentration, amount of carbon and temperature. The regression equations were used to predict >> 90% extractions as well as kinetic data.

Jan 1, 1996

By Jianhong Dong, Min Chen, Cuihuan Huang, Bo Li, Nan Wang

"Scale layer can be formed on the slab surface in the areas of secondary cooling and strand discharge during continuous casting process. From 1000 °C -1200 °C, the influence of steel composition on the stable oxide phases inside scale layer, particularly the types of alloying elements including aluminum, silicon and chromium, is investigated under different partial pressures of water vapor by the calculated predominance diagrams of iron oxide as well as its intermediate compounds formed with other metal oxides, and the stable oxide phase composition within scale layer under the working condition of secondary cooling is discussed. At lower partial pressure of water vapor, only a iron spinel (or ferrosilicate) phase is the stable phase with any alloying element contents in steel composition, whereas the stable phases are FeO and iron spine! (or ferrosilicate) inside the scale layer at higher partial pressures of water vapor .IntroductionOxide scale formation on the surface of cast and rolled products because of oxidation by the surrounding oxidizing atmosphere is a significant disturbance factor in steelmaking. The yield loss of iron because of scale formation is considerable during continuous casting and hot rolling process. Surface quality more often is impaired by scale property, which increasing the difficulty of quality assurance, dimensional accuracy and performance control. Furthermore, a potential source for subsequent surface cracking (hot shortness) can be caused by the enrichment of scrap residuals (Cu, As and Sn) at the steel substrate surface as a result of steel oxidation [1-2]. In flat products manufacture via thin slab casting technologies, these phenomena are particularly pronounced and require enhanced development efforts in descaling efficiency [3].Compared with the scale formation in continuous casting, the quantity of scale formed during hot rolling and reheating in the rolling mill is larger, and control of scale formation and descaling is a long-established task in hot rolling. Therefore, extensive research and development work have been carried out, including the effects of heating and rolling temperature on the thickness and microstructure of scale layer, heating time and furnace atmosphere, cooling mode, and steel composition on the scale formation, more attention has been given to the control of scale formation during reheating and hot-rolling process. On the other hand, hardly any specific efforts and countermeasures are taken in continuous casting, and very less research has been done despite the network-type crack on the as-cast strand surface caused by the subscale enrichment of scrap residuals [ 4-7]."

Jan 1, 2014

By Raj P. Singh

Two design-of-experiments studies were carried out to investigate the leaching of technical grade molybdenum tri-oxide (TGM) in the presence of hydrochloric acid and the mother liquor of ammonium di-molybdate crystallization used as an ammonia source. Results indicated that leaching of TGM in HCl is possible only when used at about 1N concentration. In high concentrations of HCl, technical grade MoO3 had very high solubility (7.5 to 40 g/L Mo). The most suitable conditions for HCl leaching of TGM were obtained at a slightly elevated temperature of 80°C. Using about 1N HCl at 80°C, potassium in the leached solids (TGM) decreased to about 110 ppm, a value typically obtained in TGM leached in HNO3 - NH4NO3media (3.5 - 4.0 moles /L HNO3 + 0.5 ? 1.0 moles/L NH4NO3). Mo losses under these conditions were 0.8-0.9 g/L Mo. The HCl-leach method, presented here-in, has a significant advantage in chemical cost and environmental benefits over HNO3 ? NH4NO3 purification method.

Jan 1, 2006

By Hua-qing Li

Electromagnetic stirring process effectively improves the casting quality of metals. In this paper, the physical simulation experiment, in which the molten copper is displaced by mercury, was designed. The factory test parameters were determined according the simulated data. The flow behavior of the mercury to be stirred as well as the relations between the microstructure of plate blanks and the current parameters were analyzed. With an appropriate electromagnetic stirring, the inverse segregation of tin for C51900 alloy plant blank reduces from 15 % ~ 30 % to about 5 %, and the proportion of equiaxed grain rises to larger than 30%.

Jan 1, 2009

By Darryl Lovato, Ramiro Pereyra, Daniel S. Schwartz

"During an annual inventory of nuclear material, a plated steel container which contained plutonium oxide failed. The container had been packaged for temporary storage but had been overlooked and remained in storage for more than 23 years. Although it was determined that the failure occurred through the slip-top rim, a metallurgical evaluation was requested to help to determine the integrity of the container.Optical metallography and scanning electron microscopy were used to analyze the character and degree of corrosion in the container. The depth of corrosion, measured at approximately 10 µm, did not pose a threat to the integrity of the container. However, the corrosion morphology and chemistry did suggest that a galvanic cell had developed between the tin and steel from the condensation of water. The morphology also suggests that the attack of the steel took place over a series of cycles due to changes of the environment.IntroductionMetallographic analysis was requested as part of the investigation into the mechanism of the failure of a slip-top container (#38621) containing plutonium oxide (PuO2) powder. The container had leaked during a special nuclear material (SNM) annual inventory causing contamination and closure of the vault. A photograph of the container and interior container is shown on the right in Figure 1. An initial investigation established that the source of contamination was the consequence of the failure of multiple layers of containment. Initially by the deterioration of the interior plastic bottle and polyvinyl chloride (PVC) bagout bag, and finally through the lid and steel container interface at a location where tape had not adhered properly [1]. Although the source of the breach was established, it was determined that metallographic analysis was important to establish the extent of deterioration of the steel container."

Jan 1, 2008

By James B. Pfeiffer

TETRA Technologies, Inc., has applied its HDSIM metals precipitation system to treat a waste stream containing scrubber blowdown and process water from a smelter operation. The combined stream contained cadmium, lead, selenium, arsenic and zinc, plus some iron and copper. Treatment requirements included meeting stringent mass flow limitations for specific heavy metals. The HDS ? system can reduce the arsenic from 600 ppm to less than one ppm. The process generates a dense sludge that can be reprocessed in a smelter, eliminating the liability associated with landfilling. Flow diagrams and process details are discussed.

Jan 1, 1994

By I. A. H. Schneiderl

Eichhornia crassipes approaches being a scourge in many parts of the world, .choking waterways and hindering transport upon them. At the same time it is known to readily abstract heavy metal ions from water and, thus, aids in the removal of heavy metals found in such waters. This paper considers the possibility of using specific parts of the plant as an inexpensive adsorbent for the removal of heavy metals from contaminated chemical and mining industry waste waters. In particular the root of the plant was found to be an excellent accumulator of 'heavy metal ions including uranium from solution. It is. also suggested that dried roots of the plant ?might be placed in simple bags and used in a very low cost metal ion removal system.

Jan 1, 1995

By V. I. Lakshmanan

"Historically flowsheets are developed for efficient separation of metals for economic recovery. With increasing emphasis on reduction, reuse and recycle (3Rs) efficient methods are sought to recover values from a variety of feeds where cost of collection, transportation, local consumer behaviour and regulatory guidelines dictate the development of economically viable flowsheets. Innovative understanding of potential market applications can provide means to develop value added end products. The paper with examples will discuss the use of innovative-separation technologies to obtain value added end use materials from secondary sources.IntroductionFlowsheets are developed for the efficient separation of materials of value for economic recovery. However with increasing societal pressures and regulatory initiatives for stricter environmental guidelines, there is strong need to provide focus to recover materials efficiently and economically in an environmentally accepted manner. North American industries are increasingly caught between demands for high technology value added products and responsibility for environment. An aspect that is receiving increasing attention is Design for Environment'. This incorporates a system wide approach for product design and incorporates environmentally preferable features such as recyclability, disassembly, maintainability, reusability and use of safe materials as part of a product's design objectives.The present paper with case histories will address innovative flowsheet development to convert wastes into recyclables value added products or for minimising generation of waste materials. Case HistoriesProcess for Separating Fibres from Composite Materials 1In the automotive industry, sheet molded compound (SMC) is used to produce panels, bumpers and the like. During the manufacture and at the end of life, considerable waste materials are generated which are potentially recyclable. Fibre reinforced plastics where fibre substrate impregnated with thermosetting resin, find applications in several manufacturing processes and are potentially recyclable at the end of life."

Jan 1, 1996

By Toshiaki Tsuru, Takeshi Ohgai, Hisaaki Fukushima, Shigeo Kobayashi, Tetsuya Akiyama

"Electrodeposition behavior of Zn-Cr alloys from the methanol baths was investigated. In the methanol baths of low Cr3+ concentration, Cr (III) compound was incorporated in the deposits and no lusfrous Zn-Cr alloys was deposited. However, Cr was existed as metallic state in the deposits obtained from the baths of higher Cr3+ concentration. With an increase in water content in the baths, the chemical state of Cr in the deposits changed from metallic to trivalent state. Under the condition that metallic Cr can be electrodeposited, Zn deposition was significantly polarized to the potential of Cr deposition.INTRODUCTIONAn attention has been paid to Zn-Cr alloy plated steel sheet because of its excellent properties for body panels of automobile and electrical appliances [1]-[4]. This plating process can be operated using the sulfate solutions containing Cr3+ ion [1] - [6].In decorative single Cr plating, on the other hand, many attempts have been made to electroplate Cr from trivalent electrolytes, which is motived by environmental deficiencies of the presently used hexavalent process [7]. [8]. However, it has been reported that in the aqueous solutions the behavior of the electroreduction of 0 3+ is atypical due to the complicated nature of the chemistry and electrochemistry of cr3+ species [9]-[11]. Even in Zn-Cr alloy plating, it is difficult to codeposit metallic Cr with Zn in simple sulfate electrolytes [l]-[4], [12]. Therefore, it can be expected that the electrodeposition behaviors of Zn-Cr alloys as well as Cr are significantly changed when the electrodeposition is conducted in non-aqueous plating solutions.In this study, the electrodeposition of Zn-Cr alloy was conducted from methanol solutions to clarify the electroreduction mechanism of Cr3·-Cr0 in the alloy deposition process."

Jan 1, 2000

By Qingchun Yu, Bin Yang, Yong Deng, Heng Xiong, Fei Wang, Minxiu Chen

"Metal aluminum produced by non-electrolysis process received much attention due to its lower energy consumption. In this paper, carbothermic reduction and carbothermic-chlorination of alumina in normal pressure and vacuum were studied. The products were examined by means of XRD, EDS and SEM. During the carbothermic reduction process using carbon reductant in normal pressure, no metal aluminum was found. However, when coal was used as reductant, a mixture containing metallic aluminum, A14C3, and silicon was obtained, but metallic aluminum couldn't be separated from the mixture. During the carbothermic-chlorination process in vacuum, Al404C and Al4C3 were produced by the reaction between alumina and carbon, and Al Ch gas reacted with Al404C and Al4C3 to produce Al Cl gas. Metallic aluminum was produced due to the disproportionation of A!Cl gas and condensed on the collecting plate. Meanwhile, the initial temperature of carbothermic reduction of alumina reduced in vacuum compared with that in normal pressure.IntroductionIndustrial production of primary aluminum is carried out in alumina cell by the so-called Hall- Heroult process, necessitating the use of very high currents of low voltage. The alumina from which metallic aluminum is gained must be chemically pure, otherwise impure metal results. The main drawbacks of the electrolytic production are its very high energy consumption, the release ofperfluorocarbons, and the high specific C02 emissions [1]. During the past years, there were a lot of attempts to produce metallic aluminum by carbothermic reduction of A1203 [2, 3]. Cox [4] determined the vapor pressure over the A1203-C system and performed X-ray diffraction analysis of condensed products. It was demonstrated that an increase in the carbon content in the system leaded to the sequence of transitions: A1203~Al404C~A1zoc~A14C3 ~AI [5]. In any carbothermic reduction process for aluminum, extremely high temperatures (2000 °C ) were required [6]. In spite of considerable effort, the carbothermic reduction of alumina to aluminum remains a formidable technical challenge, due to the high temperatures required, and to the formation of aluminum carbide and oxycarbide byproducts [7]."

Jan 1, 2013

By Takeshi Yoshikawa, Kazuki Morita, Kunitoshi Matsunaga

"In metallurgical grade silicon (MG-Si), most impurities mainly exist at the grain boundaries and distribute in silicon grains at extremely small contents. Grain boundary phases in MG-Si transform into liquid above the eutectic temperature, and migrate towards high temperature regions when heated under a temperature gradient. With the migration of all liquid phases in MG-Si to the surface, the impurity contents will be decreased less than their solubilities in principle.In the present work, the fundamental research was conducted to discuss the possibility for purification using the liquid phase migration technique. The purification limit was estimated by thermodynamic calculations, and metallic impurities were estimated to be effectively removed except for Fe and Al. The migration behavior of the liquid phase in the synthesized silicon substrate was investigated by unidirectional heating under infrared radiation at 1523-1548 K, and the proceeding of migration was confirmed. The migration velocity was 1.4--2.0xl0-7 mis, and found to be controlled by the liquid phase diffusion.IntroductionPhotovoltaic energy is one of promising energy resources in a sustainable society because of its inexhaustibility and cleanliness. Although the production and installation of solar cells have increased significantly during the last decade, the cost of solar cell installation is still high. To enable the widespread use of photovoltaics and for the photovoltaic electricity price to reach grid parity, a low-cost and abundant feedstock of solar grade silicon (SOG-Si) is essential. Recently, a modified Siemens process and a fluidized bed reactor process were developed to address the cost and energy issues associated with the conventional Siemens process. However, their cost reduction potential is limited because of the large energy consumption needed to convert silicon into gaseous compounds. Purification of silicon through metallurgical routes offers a promising way for producing SOG-Si from metallurgical grade silicon (MG-Si), because it enhances productivity and can also lower the process costs. Although several metallurgical processes such as directional solidification [l ], vacuum refining [2-4] and plasma oxidation [5-7], have been developed, processing times and refining efficiencies still have to be optimized."

Jan 1, 2013

By Kiyoshi Takai

The Para-Eco Incinerator Ash Processing System for cleaning slag has been developed after a seven-year pilot plant study. The major part of the system is an electric furnace heated to 1773 K. The feed material consists of a municipal solid waste incinerator ash mixture containing a reducing agent of a coke and an inorganic flux of calcium and magnesium. With this furnace system, three kinds of products are produced. They are an inorganic molten salt that is slag, molten iron alloy absorbing non-ferrous metals, and fly ash. Due to the reducing atmosphere in the furnace, the slag does not contain any metal components as well as chlorine components just like natural rock and/or aggregate. A retreatment plant modifies this slag into a practically useful aggregate. The plant consists of a slow cooling step for crystallizing the slag as well as a water granulation step. The iron components in the ash are reduced to molten iron droplets, which concentrate at the furnace bottom. The non-ferrous metal components such as copper, chromium, and others are absorbed into the molten iron but not into the molten slag. Volatile metals such as lead, zinc, cadmium and others as well as sodium, potassium, and chlorine go back into the fly ash. A solvent extraction method and/or other appropriate procedures can be used to extract the metal components from this fly ash.

Jan 1, 2003

By Motohiro Horiguchi, Kazuo Ichii, Toshio Oishi

"As a fundamental study to prepare copper-based alloys with rare earths (RE: La, Gd, Nd, Ce and Y) without any inclusions, the solubility of rare earth in liquid copper was experimentally determined. Liquid copper alloys were equilibrated with carbon and rare earth carbide in a graphite crucible in an argon atmosphere at 1523-1873 K.Solubilities of rare earth in liquid copper were determined by approaching the equilibrium values from both the lower and the ·higher concentrations than those expected· in the preliminary experiments. They were expressed as a function of temperature. Carbon in Cu-RE alloy was also analyzed and thermodynamically discussed.IntroductionOver the past several years, the demand for highly conductive and high strength copper-based alloys, such as Cu-Cr, Cu-Zr and Cu-Cr-Zr for use in electronic materials has increased.1 -7 These alloying elements are very reactive and easily oxidized to form oxide inclusions during melting. To avoid the oxide inclusions, it may be effective to utilize the strong reducing power of carbon in conditions under which no carbides form.In this study, to provide fundamental data for producing Cu-RE( rare earth) alloys without any inclusions, the solubility of rare earth in liquid copper in equilibrium with .carbon .was determined and discussed on the basis of the experimental results and the thermodynamic data.ExperimentalSample preparation for equilibrium experimentsOxygen-free copper (99.99%), lanthanum (99.9%), gadolinium (99.9%), neodymium (99.9%), cerium (99.9%) and yttrium (99.9%), and their oxides were used as starting materials.Each rare earth carbide was prepared by mixing rare earth oxide with carbon, which is a little more than the stoichiometric composition, pressing it into a tablet form and sintering at about 2000.K for 20 ks in a vacuum furnace using a graphite crucible. Powder X-ray analysis showed that only the carbon and rare earth carbide (REC2) was present in each sample.Cu-RE mother alloys (5-20 mass % RE) were prepared beforehand by mixing metallic rare earth with oxygen-free copper, and melting in an electric arc furnace."

Jan 1, 2000