Search Documents

By G. W. Birge

This report describes the carbonizing properties of the principal coal beds of McDowell County, W. Va. Coals from 14 coal beds were selected for study: Upper Cedar Grove, Middle Cedar Grove, Lower Cedar Grove, Eagle, Douglas, Iaeger, Sewell, Welch, Beckley, Fire Creek and Pocahontas Nos. 3, 4, 5, and 9. Selection was based upon estimated minable reserves. McDowell County coals rank either as high-volatile A, medium-volatile, or low-volatile bituminous coal, and this variation in rank is reflected in the wide diversity of the carbonization properties of the coals. All coals tested were either satisfactory as mined or could be upgraded to meet present chemical standards for metallurgical coke; the coals produced strong coke, as determined by ASTM shatter and tumbler tests.

Jan 1, 1958

By Susan E. Brink

The first step in determining whether Mn can be recovered by in situ leaching is to develop and test a selective lixiviant. Two column leach tests and one core leach test Were conducted by the U.S. Bureau of Mines on Mn oxide ore using aqueous sulfur dioxide (SO2) as the lixiviant. The column tests showed that aqueous S02 could selectively dissolve available Mn oxides from calcite-rich ore in a heap leach system. However, the core test showed that calcite gangue side reactions can have pronounced negative effects on the likelihood of successful in situ leaching of a calcite-rich ore with aqueous S02. Petrographic and geochemical analyses showed that both Mn (IV, III) oxides and calcite were dissolved. The abundance of dissolved Ca caused precipitation of gypsum. Acid consumption by calcite dissolution caused a rise in pH that caused the SO/S species to shift to S032-(sulfIte), which hindered reductive dissolution of Mn oxide. Gypsum precipitation did not affect complete leaching of the rock fragments in the column tests; however, it plugged the natural permeability in the core. Manganese recoveries were high for the column tests and low for the core test.

Jan 1, 2010

By William H. Lyon

In 1950 the Program Staff of the Department of the Interior undertook an exploratory study in the projection of energy requirements of the nation. This work was reported in Bureau of Mines Information Circular 7582 by H. J. Barnett. In that preliminary study Mr. Barnett, after exploring the nature of the energy economy in some detail, evolved a method for estimating how much energy will be required in the future, based on estimates of trends in efficiency of energy utilization in specific applications, the physical output of specific energy-consuming industries, size of the population, productivity advances in the economy at large, consumer preferences, and other factors. Considerable new information was developed regarding the nature of energy demands and the possible levels of requirements for each fuel under various assumed business conditions. The study analyzed the interrelationships, including substitutions, among the fuels and emphasized the need for viewing the energy economy as an integrated albeit complex whole. This exploratory study showed a need for a single comprehensive statistical re-port that would assemble and show in a uniform manner the diverse published statistical data on energy commodities now scattered through many publications. A particularly important need was for a set of historical statistics showing the production and consumption of all energy on a B.t.u. basis. As the prospective size and nature of the future energy requirements of the nation are matters of continuing importance, this report was prepared to assist further investigations of the subject. In this report the authors undertake to assemble and present in tabular form, on a uniform basis, the production and use of each of the fuels and electric energy in the United states for three census years -1929, 1939, and 1947. The year 1947, rather than a later year, was selected because it is the most recent year for which census data are available showing the consumption of fuel by each of the manufacturing industries. It is hoped that making data for these 3 years available in one re-port will provide the needed statistical background for further studies of fuel requirements and supplies.

Jan 1, 1951

By D. S. Burgess

A commercially available Halon 1301 extinguisher has been evaluated as part of an explosion-suppression system for use in coal mines. Studies were made both of the dispersion pattern of the Halon 1301 at an initial pressure of 280 psig, and of the efficacy of this suppressant against 9.5 percent methane-air flames. These flames were quenched successfully only when the suppressant was applied before the fireball diameter exceeded 18 inches.

Jan 1, 1971

By J. R. Koehler

The U.S. Bureau of Mines (USBM) ground control research program includes several projects focused on developing design criteria for yielding-pillar-based longwall gate road systems. As part of this program, mining practices at the Sunnyside Mines, Sunnyside Reclamation and Salvage Co., Sunnyside, UT, are being documented to preserve the long history of yield pillar system evolution on the property. Published information describing the specific in-mine performance of the numerous gate road configurations utilized at the Sunnyside Mines is very limited. To overcome this deficit, USBM personnel interviewed 30 longtime mine employees representing nearly 700 years of mining experience at the Sunnyside operations. Mining conditions in 12 specific areas in the Nos. 1, 2, and 3 Mines were discussed in the interviews. Also, broad topics such as general mining practices, safety, and geology were often addressed during the discussions. Comprising the body of this report is an extensive record of the events and conditions experienced while mining the identified areas. In addition, eight significant conclusions were developed that accurately summarize the general opinions of the interviewed personnel regarding mining conditions and practices at Sunnyside.

Jan 1, 1994

By M. L. Glenn

The Bureau of Mines is conducting research on Fe-based alloys using Si and Al additions to reduce the Cr required for heat-resisting appli-cations. Part of this research is being done to evaluate alloys containing (8-10)Cr-(10-14)Ni-(0-8.5)Si-(0-4) Al to determine which of these alloys have austenitic structures, as well as fabrication properties and oxidation resistance sufficient to substitute for type 304 stainless steel. Based on initial results, an Fe-lOCr-11Ni-5Si alloy and an Fe-8Cr-13Ni-5Si alloy were selected for evaluation of oxidati.on, stress rupture, and tensile properties. Both alloys have oxidation resistance at 7000 and 8000 C that is better than that of type 304 stainless steel. The stress rupture strengths are less than that of type 304 stainless steel but significantly better than that of commercial heat-resisting steels with similar Cr contents. Yield strengths of the alloys were equivalent to that of type 304. Both alloys had high tensile strengths comparable to those of stainless steels that transform to martensite during straining (e.g., type 301). These alloys have weld-hot-cracking resistance comparable to that of type 304 stainless steel. This initial study shows that Si has potential as a substitute for Cr in stainless steels for heat-resisting applications.

Jan 1, 1984

By Robert Lee Stahl

Comprehensive field tests were made by the Federal Bureau of Hines at the Conda open pit mine near Soda Springs, Idaho, to determine whether surface geophysical techniques could be used to detect and delineate faults in phosphate deposits. The tests included seismic refraction, magnetometry, electrical resistivity, and airborne photography. Of the several geophysical techniques tested in the field, horizontal resistivity profiling was the most effective method for diagnosing faults. The method is quick, inexpensive, accurate, and can be easily used by mining company personnel to detect and delineate faults.

Jan 1, 1975

This is the eighth in a series of reports en properties of commercial meter fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C. F. R.) Committee and the Bureau of Mines of the United States Department of the interior. The first report gave data en meter gasolines sold during the winter of 1935-36.3/ The present report, covering 1,679 samples, represents the products of 118 companies plus these from the Pacific coast, which were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. The throe groups of data en samples of regular, premium, and third-grade gasolines arc averaged separately. The number of samples and brands representing each grade are as follows: Regular price, 869 samples, 76 brands; premium price, 452 samples, 45 brands; third-grade, 358 samples, 82 brands. In this report the same marketing districts are retained as were used in the preceding report, and as far as possible the actual sampling points in each area arc indicated on table 1.

Jan 1, 1940

By L. C. IlsLey, E. J. Gleim, F. CRAVEN

Electrical apparatus and circuits began to be used in mines about 50 years ago. A search of the literature on mining reveals that in 1882, umping was being done by electricity in some aines of England. One account tells of a small electric locomotive being used in 1882 "to drive eight corves loaded with coal" in a mine near Dresden. In an account of his visit to some English mines, en American in 1892 mentions that he saw underground electric signals, lights, pumps, hoists, and one revolving- cutter-bar 19wall mining machine,. Among the carl electrical installa- tions in the United States was an electric locomotive in the Lykens Valley Coal Co. mine at Lykens Valley, Pa., in 1887. In 1889 the Sperry electric coal digger was being tried out. Tarce mining machines were placed in the Prospect mine, East Palestine, Ohio, in 1890. An electrical pumping plant was put in oneration during 1892 in the Woodward mine of the Delaware, Lacka- rahma & Western Railroad Co. Thus we Almost coincident with the proposed use of this new servant in under- ground workings, came the thought of making it safe in gassy mines. find an account of a design for a protected stationary electric mine lamp proposed by Edison in 1831. Enclosed-type motors rere developed in the United States and shiped to English collieries about 1903. From those early beginnings there has been continuous progress until to-day one finds hundreds of pieces of specially designed electrical apparatus distributed in American coal mines and in mines of nearly all important coal-producing countries. Along with introduction of this equipment grew the idea of the necessi- ty of government aid, in standardization. In most coal-mining countries to- day the governments either directly or indirectly have a considerable in- fluence in guiding the design of electrical equipment intended for use in Pasay mine

Jan 1, 1933

By T. W. Johnson

The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past-several years the flow of natural bas through high--pressure pipe lines.4 This report deals with that part of the study involving the design of pipe-line, systems consisting of lines laid parallel to each other. The lines are deferred to as the original line and the parallel line. The paralleling line may or may not extend the entire length of the original line; however, the parallel line is, connected at its two ends to the original line. As a result of the large expansion of the natural-gas industry almost all markets within economic distance from the developed gas fields have at least one pipe line supplying them with natural gas. Small increases in the consumers' demand for natural gas can be met usually by increasing operating pressures, but any marked increase in demand necessitates paralleling sections of the existing systems. It is believed that to a large extent future

Jan 1, 1934

By T. L. Iapalucci

To determine the behavior of chlorine in coal combustion, the Bureau of Mines burned 10 chlorine-containing coals, high-, medium-, and low-volatile, in a laboratory-scale pulverized-coal combustor. At carbon-combustion efficiencies of 94 to 98 percent, 1.6 to 7.1 percent of the chlorine or an average of 4 percent of the chlorine in the coal was retained in the ash; the balance, predominantly hydrogen chloride, was evolved in the combustion gas. Sulfur retention in the ash ranged from 2.3 to 10.7 percent or an average of 6.3 percent, Addition of alkali and alkaline earth carbonates to a medium-volatile coal containing 0.27 percent chlorine by preferentially reacting with the chlorine increased the Cl/S atom ratio in the ash, Lithium carbonate addition at 0.43 percent and K2C03 at 1.59 percent increased the C1/S ratio in the ash from 0.2 to 0.6.

Jan 1, 1969

By T. W. Johnson

The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past several years the flow of natural gas through high-pressure pipe lines. This report deals with that part of the study involving the design off pipe-line systems consisting of lines laid parallel to each other. The lines are referred to as the original line and the parallel line. The paralleling line may or may not extend the entire length of the original line; however, the parallel line is connected at its two ends to the original line. As a result of the large expansion of the natural-gas industry almost all markets within economic distance from the developed gas fields have at least one pipe line supplying them with natural gas. Small increases in the consumers' demand for natural gas can be met usually by increasing operating pressures, but any marked increase in demand necessitates paralleling sections of the existing systems. It is believed that to a large extent future

Jan 1, 1934

By Gary E. Sherman

The Bureau of Mines estimated the remaining lode gold endowment of eight mining districts in Alaska using historic production data. A log-arithmic model of cumulative tonnage of ore processed versus cumulative grade was applied to the following districts: Chichagof, Fairbanks, Homer, Hope-Seward, Juneau, Ketchikan, Prince William Sound, and Willow Creek. To assess the remaining endowment, a computerized production data base was compiled from Bureau records. These data were aggregated in 5-yr intervals for each district. Data were sorted in order of declining grade, and log cumulative grade was plotted against log cumulative tonnage. Linear regression was performed on the data for each district. The linear equation for each curve was used to predict remaining endowment at a limiting mining grade. Based on conservative extrapolation of the grade-tonnage curves, a substantial total endowment of 8,415,100 tr oz of gold remains in the eight districts. The districts with the greatest remaining endowment are the Juneau, Chichagof, Fairbanks, and Willow Creek Districts.

Jan 1, 1987

By John B. Knaebel

This paper is one of a series being prepared by the Bureau of Mines on mining methods and costs at various mines in the United States, Canada, and Mexico, and is a description of practice at the Edwards mine of the St. Joseph Lead Co. ACKNOWLEDGMENTS The cooperation and assistance of the officials of the St. Joseph Lead Co. in permitting publication of this paper and providing every facility for its preparation are gratefully acknowledged. Especial thanks are extended R. J. Mechin, manager, R. F. Mitchell, mine captain, and J. S. Brown, geologist, for their generous aid, and the assistance of W. H, Weijola, mine engineer in assembling some of the illustrations is deeply appreciated, The helpful suggestions of C. F. Jackson, principal mining engineer, U. S. Bureau of Mines, are gratefully acknowledged.

Jan 1, 1932

By James J. Dawd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the ninth of a series of reports giving results of studies by counties under part (1) of the investigation. (See Appendix.) This report covers Raleigh County, W. Va., which comprises parts of Bald Knob, Eccles, Beckley, Meadow Creek, Mullens, Flattop, and Big Bend quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, location of drill holes, bed and total coal thickness, and outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas. areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps, Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

By W. E. Cooper

The International Intercalibration and Intercomparison Program (HIP), consisting of several selected laboratories from four countries, held a radon progeny intercomparison measurement at the U.S. Bureau of Mines experimental Twilight Mine on September 12-14, 1988. Grab samples were taken at four different conditions of low and high radon progeny and condensation nuclei concentrations, respectively. The results showed good agreement among all seven participants. The coefficient of variation of all measurements was 4.7%; after minor corrections for flows and some systematic biases, it was reduced to 3.2%.

Jan 1, 1990

By R. M. Santmyers

Except for optical purposes and a few other special uses quartz and quartzite are to a considerable degree interchangeable. This also may be said with respect to pulverized quartz and ground silica sand, which are discussed in a separate paper of this series. All these materials, except perhaps quartz crystals of optical grade, are abundantly available in many parts of the United States. In the form of ordinary crushed stone much of it is sold at $1 a ton or less, and ordinarily

Aug 1, 1931

By D. A. Reynolds, C. R. Holmes

The Bureau of Mines - American Gas Association ( EM - AGA) carbonization test has been used to determine the carbonizing properties of 66 American coals and a larger number of coal blends . A summary of the results obtained for the first 30 coals , including 6 blends , has been published ,4/ and results for individual coals have been reported as the investigations were completed . A bibliography of all publications pertaining to this work has been issued recently . Many of the coals were carbonized at 800 ° and 900° C. in two sizes of retorts ( 13- and 18 - inch diameters ) ; and , because the quality of coke is affected by changing the size of the retort , this report has been prepared to show the average physical properties of coke from the two sizes . This report also purposes to extend the correlation of the physical properties of coke with the rank of coal made by Fieldner and Davis in their summary of the EM-AGA tests on the first 30 coals .

Jun 1, 1942

By LeRoy R. Curwick

This Bureau of Mines report presents the results of a study conducted to assess the domestic availability of chromium from superalloy and cast heat- and corrosion-resistant alloy scrap material. Six alloy classes included in this survey were investment cast, hardfacing, and wrought nickel- and cobalt-base alloys, wrought nickel-iron-base alloys, and heat- and corrosion-resistant alloy castings. Data were collected for 1976 on metallic scrap generation, use patterns, and production practices for these alloy producing and using industries. A model was developed that allowed an assessment of the materials flow circuits within the industries that produce these alloys. The types, amounts, sources, secondary products, and ultimate destinations of chromium- containing metallic scrap for the six alloy classes were determined. Regarding the overall recycling efficiency of these alloy producing and using industries, of the 580.9 million pounds of scrap generated from these six alloy classes in 1976, about 72 percent (416.8 million pounds) was remelted by the same alloy-producing industries, about 18 percent (104.9 million pounds) was downgraded into stainless and low-alloy steels, about 3 percent (19.7 million pounds) was exported, and about 7 percent (39.5 million pounds) was lost through landfill or other disposal or service wastage. The lost material is primarily contaminated oxides for which recovery is currently uneconomic. However, the 124.6 million pounds of scrap material downgraded or exported in 197b contained potentially recoverable critical strategic elements. The amount of scrap material lost to the six alloy-producing industries in this manner contained 22.1 million pounds of chromium, 53.4 million pounds of nickel, 5.9 million pounds of cobalt, 35.9 million pounds of iron, and 7.3 million pounds of other alloying elements.

Jan 1, 1980

By Gerald W. Elger

The Federal Bureau of Mines developed a modification in the conventional Kroll process for preparing high - purity hafnium metal . This modification involved the partial replacement of magnesium by sodium in the batch reduction of purified hafnium tetrachloride to sponge metal . The raw tetrachloride was purified either by thermal degassing of the volatile contaminants to the atmosphere or by fused- salt treatment . In the fused- salt treatment , the tetrachloride was contacted with molten alkali chlorides to remove the impurities . The reaction byproducts were removed from the metal by heat treatment in an evacuated furnace . The metal sponge was consolidated by melting into buttons or ingots , which were analyzed for impurities . The purity of the metal prepared by the modified process is superior to that of the metal produced by the conventional method . The hafnium metal was comparable to crystal - bar hafnium except for the oxygen content , despite the abnormally high impurity concentrations in the raw tetrachloride . Several ingots were successfully cold - rolled to sheet .

Jul 1, 1960