Search Documents

The expense of mine environmental and planning process approvals is a fundamental and proper part of mine planning and feasibility costs. It is not a cost that should be the subject of challenge nor is it a cost that should be avoided. However the additional process approval costs incurred by bureaucratic delay, process duplication and administrative incompetence is a scandal and a deterrent to investment.

Jan 1, 1992

By A F. Idziak

The aim of the present study was an application of coal optical property measurements for analysis of paleostress field existing in fault zones of the Upper Silesian Coal Basin (USCB) during the coalification of organic matter. Measurements of vitrinite reflectance were carried out on coal samples taken near a hanging stope of the Klodnicki fault. Other samples had been taken in vicinity of the Krzyzowicki fault. The Klodnicki fault is one of the main tectonic discontinuities in the northern part of the USCB. It is postulated that its origin is related to the deep-rooted latitudinal discontinuity in crystalline basement of the basin. The Krzyzowicki fault is located in the western part of the USCB where fold tectonic style dominates. Vitrinite, one of the basic components of hard coal is generally considered as optically anisotropic material. Anisotropy of physical properties is induced mainly by stress, which arranges vitrinite structure. Vitrinite anisotropy can be described by an ellipsoidal model called reflectance indicating surface (RIS) which is a geometrical representation of the optical anisotropy tensor. The investigation of the RIS for vitrinite was carried out on coal samples. The apparent maximum and minimum reflectance values measured for a single vitrinite particle were plotted against corresponding bireflectance to construct the reflectance crossplot. Interpretation of this plot yielded the magnitudes of the RIS three principal axes. The data obtained point to differences in optical anisotropy of coal under the study. The coal samples taken from block tectonic zone near the Klodnicki fault had mean reflectance value of less than 0.80 per cent. Their anisotropy coefficients were about 0.1. Optical properties of coal changed from the biaxial positive in the western segment of the fault to the biaxial negative in its eastern part. It suggests that past tectonic stress was greater in the western part of the zone than in the eastern one. Coal originated from a fold tectonic zone at the vicinity of the Krzyzowicki fault has mean reflectance value much greater than from previous region (ÿ1.20 per cent). Its optical anisotropy coefficient is equal to about 0.07. It suggests that paleostress field was more isotropic. The presented study shows the usefulness of coal reflectance measurements in the analysis of paleostress field existing during coalification process.

Jan 1, 2003

By Moxon NT

The detonation pressure of ANFO can be significantly reduced by the addition of low density materials such as polystyrene, bagasse, sawdust or perlite. Laboratory and field test results have shown that homogene- ous mixtures of these low density explosives can be produced in a bowl truck and loaded into a blast hole without segregation. The detonation pressure of the mixture can be tailored to suit the material to be blasted by varying the quantity of low density additive incorporated into the mix- ture. Results obtained in the field indicate that these low density explo- sives can lead to significant cost savings without compromising fragmentation or production.

Jan 1, 1988

The kinetics of the hydrogen reduction of iron oxides in granular calcined bauxite were studied at 550-1,050°C in a shallow bed reactor. The iron oxides behaved as a dispersion of particulate iron oxide in a porous alumina matrix in which the iron oxide particles were reduced independently. The observed rates of reaction were found to be virtually independent of the bauxite grain size. At 800,°C and above, the reduction was multistage, Le.1. Fe203 +2Al203 (matrix) ?2FeAl204, and2. FeAl204? Fe0 +Al203.Reaction 1 was very rapid. Reaction 2 was much slower, the latter stages being controlled, at least in part, by phYSIcal changes of the Fe0 and a-Al203 produced in the reaction. Owing to the observed nature of the material, the reaction rate controlling steps could not be determined.

Jan 1, 1972

By Spark R. F

The copper deposits at Pernatty Lagoon are predominately djurleite-digenite bodies beneath the permanent water table, and chrysocolla-atacamite-malachite above the permanent water table. The minerals havebeen deposited as sheets, lobes, and pods in zones suggestive of permeability channels or permeability basius with respect to groundwater circulation.Pyrite is deposited in the form of framboids, which reflects its biogenic origin. Copper-iron sulphides deposit by replacement of pre-existent pyrite, and rarely by direct deposition. The latter mode of formation results in complex crustification bandings of chalcopyrite, bornite, sulphur rich bornites, digenite, and blue remaining covellites. The copper-iron sulphides appear to reequilibrate under constrained oxidation, resulting in an iron depletion and associated copper enrichment, the final product of which is a djurleite-digenite assemblage and associated with goethite. Where copper mineralization/ host rock relationships have rendered the rocks entirely impermeable to post ore groundwater movement, then the copper-iron sulphides are preserved as the ore assemblages.Minor and trace minerals observed include sphalerite, carrollite, galena, wittichenite, and possibly tetrahedrite in the primary ores. In the oxidized ores cllprite, tenorite, and trace brochantite have been found.

Jan 1, 1976

The Greens are asking the question: what do our mining towns look like in 2050 and how can we be better prepared? The resources boom brought enormous profits to the main players and was partly responsible for insulating Australia through the worst of last year's global economic turmoil. However, with indicators of a resurgent mining boom, it is essential we learn from the recent past. The last boom saw housing stress at levels unseen in the big cities, health services strained to breaking point, and Aboriginal poverty side by side with some of the most lucrative industrial precincts in the country. Much of the wealth still flies right over the heads of regional communities as fly-in, fly-out operations proliferate.   Behind these local stresses, resources booms rely on the stripping of non-renewable resources which will eventually run out, and the unique environment of the north-west is taking a battering.    Communities of the north-west have a perilously narrow economic base which must be broadened if townships of the Pilbara and Goldfields are to avoid the fate of places such as Goldsworthy and Wittenoom. Unless this is informed by local communities, decisions will be made in capital cities thousands of kilometres away by people largely ignorant of the unique conditions prevailing in regional Western Australia.   Global climate change negotiations and oil depletion will heavily penalise emissions-intensive economies like Australia which fail to keep up as the world moves to a low-carbon environment. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Jun 1, 2010

Roadheader tunnelling machines have been used in Australia by both mining companies and contractors involved in the mining and con- struction industries since the early 1970's. They have both advantages and limitations, and this paper discusses machine excavation from the point of view of a contractor who has both reaped the benefits and suffered the conse- quences of using roadheaders. The paper also includes brief descriptions of three projects tackled by roadheader, all the projects being Declines.

Jan 1, 1987

By Ward S. D

When using grinding time for a batch grinding operation as a measure of the energy usefully employed for comminution; the assumptions made are often not valid. A kinetic approach, based on a study of the rate constant, or k, value for the material is more acceptable. The Rosin-Rammler distribution equation has been theoretically derived from the general equation for first-order batch grinding. This relationship, incorporating a term for k, was used in a study of the rod milling of a binary mixture of quartz and limestone.The presence and degree of interaction between the components was considered by comparing the size distribution of the mill product with that predicted by assuming the overall distribution equal to the sum ofthe distributions given by the Rosin-Rammler equations for each component weighted according to its volume fraction in the mixture. The interaction was found to be complex and particularly sensitive to particle size.A simple graphical procedure was devised to predict the size distribution of the mill. Product components and this gave a fairly good approximation to experimental data.

Jan 1, 1976

By Pollard D. M

Chalcopyrite samples from two different localities were leached in oxygenated mixed chloride-sulphate lixivants at elevated temperatures and atmospheric pressure. The oxidation of chalcopyrite was found to follow predominantly linear kinetics. The slope of the major region was dependent on stirring rate, oxygen flowrate and chloride concentration while only slightly dependent on the surface area of the sample leached. This region was found to predominate only at low temperatures. The oxidised chalcopyrite releases cuprous and ferric ions into solutions. Chloride ions complex these dissolved ions to effectively move the equilibrium of the leaching reaction to the right. When the level of chloride in solution was below 6 g/l, the unstable cuprous ions were found to reprecipitate with sulphur as covellite. When no chloride was present and the lixivant was a solution of sulphuric acid then ferric sulphates precipitated. The overall leaching reaction occurring in the leaching system is: CuFeS2 + 5H+ + 1.25 02 = Cu 2+ + Fe 3+ + 2S¦ + 2.5H20

Jan 1, 1987

By A Purchase, C Stacey

The procedure for operation of deluge systems installed in road tunnels is still a subject of debate. The work undertaken in this paper assists in the understanding of the effects of deluge in road tunnels, and thus aims to help inform the development of operational policy. Analysis was undertaken using computational fluid dynamics (CFD) simulations to help explore the deluge interaction with the tunnel ventilation (including smoke exhaust) and combustion products. It was found, for the scenarios considered, that: Deluge activation can decrease the required critical velocity for smoke backlayering, and this in turn can improve the effectiveness of a smoke exhaust system.The dominant parameter for deluge effectiveness is the vehicle configuration, with shielded scenarios (such as a fire in the passenger compartment) showing almost no water reaching the fire. The water delivery rate (5 mm/min versus 10 mm/min) has only a minor effect on the smoke duct damper inlet temperatures and downstream smoke temperatures for small fires (5 MW). For large fires (50 MW) the higher water delivery rate gives slightly improved performance (lower damper inlet temperatures and lower downstream smoke temperatures). A one-dimensional transient tunnel model incorporating different operational and deluge response policies (ie deluge activation times) was developed. It was used to examine the influence of different operational parameters on life safety risk and tunnel damage risk. It was found, for the scenarios considered, that: The life safety risk for different scenarios has a sensitivity to deluge activation policy with the case of delaying the deluge activation for a long time giving the worst outcomes. However, the most critical parameters for life safety risk are operator response time (for all response activities, not just deluge) and the type of fire (configuration, size and growth rate).There is a reduction in risk of tunnel damage when the deluge is activated earlier, although the fire configuration (ie whether or not the seat of the fire can be reached) has the greatest influence on the outcome. It is concluded that the deluge activation policy should be case-dependent. It will depend on the tunnel, the safety systems provided, and most particularly the vehicles involved. The current policy in Australian tunnels is for manual activation of the deluge by the tunnel operator as soon as practical after the fire is confirmed (see also PIARC, 2007). This is a good policy. However, future work may be helpful to improve the skills of operators to make the best judgement as to when deluge should be activated, balancing all risks. This work could include research to further the understanding of deluge and fire in road tunnels, training programs and consideration of historical fire events.

Jan 1, 2008

In the 100 years since the formation of The Australasian Institute of Mining and Metallurgy there have been significant changes in all aspects of the mining industry.A number of the changes have been driven by technical evolution or necessity, others have been driven by developments in the application of the products produced from the mining of minerals. Other changes have been driven by shifts in community values.

Jan 1, 1993

By Laajalehto K

The basic condition necessary for flotation is hydrophobicity of the surface of the mineral to be floated. For sulphides, this condition usually requires treatment with a collector solution. The conditions for this treatment have until recently usually been chosen by the trial and error principle which has indeed been working relatively well under favourable conditions; ie for simple homogeneous ores. However, the present tendency to increasing use of complex and often relatively lean ores sets increasing requirements for the control of the flotation process. This development is the reason for the present rapid development of process control methods in flotation. In addition to the already well-established practices of pH and reagent feed controls, the importance of measuring and controlling the electrochemical potential of the ore particles to be floated is recognised in the case of sufficiently conductive minerals. In fact, the electrochemical potential seems to be the basic quantity determining the flotation behaviour of such relatively well-conducting minerals as sulphides. Since the hydrophobicity of the mineral and, hence, its flotation properties are ultimately determined by the composition and structure of its surface, information on these under different process conditions is important for design and operation of efficient flotation processes. The basic requirement set for the methods used for obtaining this information is high surface sensitivity of the method. The recent rapid development of surface characterisation has produced several methods which fulfil this requirement. Their application to the problem of characterising surfaces of mineral samples in contact with collector solution is, however, often complicated. The main reason for this is the vacuum environment necessary for the measurement. In the case of flotation experiments this means that in most of these methods the measurement cannot be made in situ, but the sample must be extracted from the liquid and subsequently evacuated in the vacuum chamber of the instrument. It is essential to carry out these steps so as to avoid to the extent possible changes in the sample surface. For the purpose of establishing whether this has been accomplished it is important to compare the results of methods operating in vacuum with some available in situ method. An optimal choice of methods seems therefore to be a combination of the available powerful vacuum methods with in situ measurements. The most usual combination seems to be X-ray photoelectron spectroscopy (XPS or ESCA), Fourier transform infrared spectroscopy (FTIR) and electrochemical measurements. This choice combines the unique possibilities for direct elemental and chemical characterisation offered by XPS (Cecile, 1985) with the in situ capability of FTIR and electrochemistry. In the XPS measurements, it is essential to apply a special sample handling technique to avoid loss or damage of some sensitive species of the collector-based layer on the mineral surface. In the following will be given some examples of the application of the XPS technique in combination with electrochemical methods of sample treatment to studies of the layer formed on sulphide substrates in ethyl xanthate (EX)

Jan 1, 1993

By Turner T. M, Jorgensen F. R A

The tendency of the concentrate to ignite was studied using four techniques, namely, laminar flow furnace, fluid bed, thermal analysis and boat-in-furnace. Exothermic activity occurred at two temperatures: minor activity in the vicinity of 200¦C, major activity at 330-350¦C. The low temperature reaction was due to the ignition of a small amount of free sulphur while the major activity was associated with the ignition of the sulphide minerals, notably pyrite. To avoid ignition of the sulphide minerals, the gas temperature should not exceed 300¦C and the oxygen content of the gas phase should be as low as possible. It was shown that little of the arsenic in the concentrate entered the gas phase during drying.

Jan 1, 1987

Thank you for asking me to address you. The topic may sound formidable. Those of you with determination to go somewhere in your careers will understand that by taking geoscience, mining and metallurgy courses as students, you are declaring your intere

Jan 1, 1994

By F

Ore reserve estimation has been described as the most individualistic, the most prickly and even the most controversial of all the technical aspects of the mining profession. This symposium is a great opportunity to look at the present state of the art and full marks must go to the Sydney Branch for organi- sing it at this time. The first essential of good ore esti- mation is probably an awareness of the uncertainties involved, and the possible impli- cations of these uncertainties.

Jan 1, 1979

The reasons for including treatment of water in Whites and Intermediate open cuts in the overall rehabilitation strategy are given in the introduction. The target quality of the treated water also is discussed. Equipment selections are reviewed and reasons given as to why certain choices were made. The differences between this plant and an ore dressing mill are highlighted. An outline of the operating procedure is included along with a basic flowsheet. Cost estimates are briefly Discussed.

Jan 1, 1984

Mineral resource and ore reserve estimation is a challenging and demanding field, requiring application of professional knowledge, skill and experience of the highest order. If the many potential hazards and pitfalls are to be avoided however, there are two other requirements which are of equal, if not greater importance:

Jan 1, 1990

`WELL HE WOULD, WOULDN'T HE?' Public Relations people have something in common with advertising people and politicians: there exists a perception that their whole Raison d'Etre is to create, mould, and maintain images which are far removed from reality

Jan 1, 1994

The Century zinc deposit is located in Queensland approximately 250 kilometres north north-west of the provincial city of Mount Isa, on Lawn Hill Station and within 150 kilometres of the Gulf of Carpentaria.ThefirstMining Lease in this area was pegged in 1887. The Silver King vein is the largestvein deposit in the area and has produced lead and zinc, in addition to 74,000 ounces of silver during its history.A total of forty three veins containing silver, lead and zinc are now known, all of which were discovered by prospectors within 10 years of the first vein being recognized.

Jan 1, 1993

By Hunter M. M

The present value of the future profits of a mining operation, using a discount factor which represents the effective cost of venture capital, provides a measure of the projected success of the operation. The present value can be maximised by appropriate selection of cut-off grades successively through the life of the operation. A case study is presented in which detailed optimisation of cut-off grade results in a worthwhile increase in profitability compared with the use of a constant, break even, cut-off grade.Some implications of this approach to profit optimisation are discussed.

Jan 1, 1992