Search Documents

By Z. T. Bieniawski

Results of in situ investigations are discussed providing comparisons of rock mass deformability measurements by three methods: 'petite sismique' technique, the Goodman borehole jack and flat jacks. The tests were performed in exploratory tunnels constructed for site characterization purposes of an underground hydro-electric scheme. Due to the large number of data (41 petite sismique measurements, 45 Goodman jack tests and 19 flat jack measurements), it was possible to evaluate thoroughly the testing techniques employed. The purpose of this paper is to indicate the problems encountered in the interpretation of the results and to offer suggestions for selecting in situ tests. INTRODUCTION In situ tests are expensive and time consuming but they are an important aid in tunneling applications since they can provide deformability data of rock masses in contrast to rock material characteristics obtainable from small laboratory specimens. Some in situ tests are relatively easy to perform but their reliability may be in question unless a comparison of the data obtained by several different test methods is possible. Although many in situ techniques are available for determination of rock mass deformability (1), those more convenient to use are the Goodman jack, flat jacks and 'petite sismique. These methods are considered convenient because the Goodman jack is a borehole device; flat jacks can provide not only deformability data but also information about the stress field around excavations; while 'petite sismique' is based on seismic refraction surveys. Accordingly, these three methods have been selected for comparison.

Jan 1, 1979

By F. A. Aplan, Richard R. Klimpel

This article discusses the role of mathematical optimization techniques as applied to the design and analysis of particulate processing plants. The emphasis will be placed on the macro engineering view of integrated multiple operation plants such as those that typically involve stages of size reduction, sol id-sol id separation, solids storage, chemical reactions involving sol ids, sol ids disposal, etc. The macro engineering view is chiefly concerned with balancing and optimizing the bigger picture of how various unit operations interact technical and economically with each other in an approximate sense rather than how a specific unit operation can be technically described and optimized in detail (micro engineering.)

Jan 1, 1991

By Stephen G. Tough, Ted M. Noskiewicz

INTRODUCTION For many years, in Europe and in North America, pre-formed metallic and concrete segmental linings in tunnels have been used extensively as temporary and permanent ground support systems. In the United Kingdom the use of cast iron as a means of ground support in mining shafts dates from the first decade of the 19th century. Although at that time wood tubbing was extensively employed, cast iron was used in shafts at Wallsend and Percy Main collieries in the North East of England. The original form of cast iron tubbing consisted of cylinders which were lowered bodily into the pit and were built from the bottom up, but subsequently they were subdivided into segments which involved the making of vertical as well as horizontal joints. Principally, the practice of providing immediate pre-formed support developed because of the incompetent state of the surrounding ground and, although this still remains the over-riding consideration nowadays, several other factors are examined before finally deciding what type of lining to use. Other branches of sub-terranean technology such as tunnel thrusting or immersed tubes (both of which involve pre-formed linings) can provide alternative solutions to problems hitherto thought better solved by bored tunnelling methods. However, this paper will confine itself to those linings developed for the more traditional tunnelling methods. Usually the shape of segmentally lined tunnels is circular because this profile is the most suitable for bad ground and many tunnelling machines. This does not always lead to the most economic use of space within the tunnel and horseshoe or elliptical linings are sometimes used in suitable ground. The number of segments

Jan 1, 1974

By A. T. Yu

Two key components make up the core of a rapid excavation operation. They are: the breaking up of the rock and its removal. Owing to the complexity inherent in mechanical rock-breaking and the relative infancy of the art, for a number of years the first of these two components has received virtually undivided attention from the industry. Only recently has some concern been expressed about the technology and the economics of the much ignored second component: muck removal. As the continuous boring machine's percentage downtime continues to trend lower in the future, the need for adequate and more effective materials handling systems in rapid excavation will become increasingly more acute. (1) Recognition of the need for a broader and more far-sighted approach to our problem has been eloquently underscored in the conclusions of the Committee on Rapid Excavation sponsored by the National Research Council: "Ultimate attainment of the desired cost and speed improvements is significantly dependent on recognition of the excavation process as a system whose subsystems are critically inter-related. Substantial amounts of full-scale field testing of integrated driving, muck removal, and support subsystems are required." (2)

Jan 1, 1997

By E. D. Attanasi

Exploration for non-fuel minerals has declined since 1988 as recessionary pressures have slowed growth in the industrialized economies. By most accounts, however, 1990 expenditures were still significantly greater than the low levels experienced in the mid-1980s. The Persian Gulf crisis introduced instability in energy prices and greater uncertainty into an already cloudy economic picture. As 1990 unfolded, the US savings and loan problems spread to the commercial banking system, leading to the failure of several major US commercial banks. The Japanese stock market also suffered significant losses as Japan's Central Bank raised interest rates. The Soviet Union experienced shortages of food and other basic items. Its government faces resistance to changes leading to a market economy. Individual Soviet republics also are seeking more control of their own destiny. The cost of German reunification, in terms of the capital required to bring the east's infrastructure and industrial base to western standards, also appears to have been underestimated.

Jan 1, 1991

By Julián Ortiz C., Clayton V. Deutsch

Indicator simulation allows specification of different continuity of high and low values through the use of grade thresholds. The sequential implementation of indicator simulation has been widely used, but the problem of order relation deviations remains a significant drawback. A new procedure for "Hierarchical Indicator Simulation" is introduced that avoids order relations and offers greater flexibility than the conventional sequential approach. The new implementation simulates all locations at the largest threshold and then considers decreasing thresholds in turn. All nodes with grades that are above the previous threshold are excluded from the domain of the current threshold and therefore, they are not used as conditioning data. The probability of being above or below the threshold is calculated using simple indicator kriging using all conditioning data in the domain, thus the covariance structure is preserved. The theoretical framework of this new approach is fully developed. Practical implementation details are discussed. Application to a copper deposit shows the advantages and drawbacks of the method. Finally, the possibility of incorporating multiple-point statistics is discussed.

Jan 1, 2002

By John R. Wright

This paper reviews the increased use of mechanization in order to develop lateral headings efficiently and economically. Particular emphasis is placed on the role of the Electric-Hydraulic Drill Jumbo in achieving this goal. Also, the use of modified mining equipment to suit various operating conditions is discussed.

Jan 1, 1981

By Xuehui Zhang, Yun Bai, Qiaosong Li, Huiming Wu

"Construction activities account for a large share of the global Greenhouse Gas emission. In the past 10 years, project decision-makers and researchers have been paying more attention to the carbon emission of tunnel projects. In this paper we study the carbon emission calculation in shield tunneling. The objective of this paper is to: (1) analyze the complex variables which affect the total emission of shield tunneling; (2) develop and illustrate a new data-mining-based method to estimate the carbon emission in the construction phase; (3) assess the emission prediction reliability of a data-mining-based method—the Randomforst model, with R programming language. This study is based on a large-diameter shield tunnel built in Shanghai, China, and shows that a reliable predictive performance can be achieved with this new data-mining-based method. INTRODUCTION Climate change caused by the Greenhouse Gas (GHG) emission has been a hot topic in recent 20 years. Both governments and non-government-organizations are trying its best to control the climate change. Since the 1990s, the general consensus is that carbon emission reduction and carbon sinking (the work of capturing the emitted carbon) are two ways of mitigating the global warming effect, with the former being more exercisable. The challenge posed by global warming also motivates the project decision-makers to take measures to reduce the GHG emission. The 5th Assessment & Report on Climate Change (published by IPCC, the Intergovernmental Panel on Climate Change) suggests that building industry contributes to 5% of the total direct emission. The building industry has shown more awareness of the impact of GHG emissions with construction activities. Shield tunnels act as an important component of the infrastructure system, and have been the dominant way of utilizing the underground space, as well as a competitive alternative to passageway underneath rivers. To study the environmental effects of shield tunneling, there is a need to quantify the carbon emission of shield tunnel construction."

Jan 1, 2016

By Robert L. Russell

Production at Freeport Indonesia's Ertsberg open pit copper-gold mine started in 1972 at a rate of 7.5 kt/d (8270 stpd). Mill throughput remained at that rate for several years until the discovery of the Ertsberg East (GBT) ore body. This discovery prompted three succes¬sive expansion stages from 1981 to 1988 that boosted production to 20 kt/d (22,000 stpd). In 1988, the discovery of the huge Grasberg porphyry copper deposit launched an era of much larger expansions. The first of these was the installation of a fourth primary mill in 1989 that increased throughput to 32 kt/d (35,270 stpd). That was followed by an expansion of the crushing and screening plant and in 1991 the addition of a new south concentrator to bring production to 57 kt/d (62,830 stpd). The addition of a primary ball mill and the changeout of the original Denver flotation cells in 1993 brought production to its current level of 66 kt/d (72,750 stpd).

Jan 1, 1994

By Irving Hoch

INTRODUCTION The demand for tunnelling can be related to urban population size and density; often, tunnelling occurs when a certain city size and density threshold is reached, and increases thereafter as a function of those population characteristics. Subways for rail mass transit are the most notable example, of course, but tunnels for water supply and perhaps for sewerage can also be related to size and density. As cities grow large they sometimes outgrow their local water supply and have to import water from distant places via tunnels; witness New York City, Los Angeles and San Francisco. And it has been suggested that Chicago use deep tunnels for storm water storage because tertiary treatment to meet water quality standards will require treating storm water runoff.(1) Other uses of underground space also increase with urban density, e.g., underground parking, concourses and shopping centers such as Rockefeller Center in New York City and the Place Ville-Marie in Montreal. These examples can be viewed as illustrative of the central point of urban land economics. As the number of people locating in a place increase, they bid up land values and make the more intensive use of land economic, with land defined to embrace the space both above and below the surface. Hence, we are led to think about the city, and of urban land use, in three dimensions. Now, if we accept the relation of underground space use to urban size and density, recent demographic trends seem anything but hopeful for future tunnelling demand: urban density is declining, population growth is slowing down generally, and there

Jan 1, 1974

By Carl G. Bock

INTRODUCTION Rapid transit systems involving near surface tunneling in hard rock are becoming more numerous, especially along the northeast corridor of the East Coast. Tunneled systems are under construction in Washington, D.C. and are being planned for Atlanta, Buffalo and Baltimore. Near surface tunneling is defined for this paper as being that in which the crown is 100 feet or less below ground surface. For Rosslyn Station, the total cover ranged from 52 to 70 feet. The rock cover, however, ranged from 40 to 50 feet which is slightly less than the station height and about two-thirds of its width. Rosslyn Station (Fig. 1) is the only station excavated completely in hard rock in the Virginia portion of the 98.5 mile Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system. The station site, oriented in a north-south direction beneath a main thoroughfare and flanked by multistory office buildings, was fixed by the need to serve a dense population center at a specific location and geologic conditions were a secondary consideration in siting. There was no previous underground rock excavation in the Washington Metropolitan Area of the size and scope of Rosslyn Station that offered a practical case history guide to the geologic conditions and excavation problems to be encountered. GEOLOGY The regional geology of the Washington Metropolitan Area is divided into two physiographic provinces by the northeast trending Fall Line (Fig. 2). Northwest of this boundary is the Piedmont Province

Jan 1, 1974

By Richard P. Curtin, Madan M. Singh, Francis S. Kendorski

INTRODUCTION The use of roof and rock bolts to reinforce the strata is an established method of rock support in both underground and surface excavations. However, the need to drill a hole, extract the drill-rods, and then place the bolt is time-consuming and costly. This becomes even more significant if the bolting is repetitive and extensive as in coal mining. Though the main thrust of this development was directed towards coal mining, the basic concepts are also widely applicable to all excavations. The authors, therefore, feel that this innovation should be of interest in rapid excavation and in tunneling. In the case of coal mining, it has been established from past statistics that the roof-bolting operation is the most hazardous activity. This is primarily because of the operator being exposed to unsupported ground. It is evident that remote installation of roof bolts would markedly improve the safety of the operation, if accomplished more readily with self-drilling bolts rather than the conventional two-step variety operation. Thus, in addition to increasing productivity, this development can be considered to be a milestone towards further improvements. The objective of this program was to establish the technical and economic feasibility of self-drilling roof bolts for use in coal mines. It might be clarified at the outset that this work was, therefore, directed primarily at showing that workable self-drilling bolts with less cost can be developed, which could be effectively used in mines. It was not to fabricate a production model bolt.

Jan 1, 1979

By Elwyn King, Donald J. Dodds

"...Unfortunately, the research activities in soil mechanics had one undesirable psychological effect. They diverted the attention of many investigators and teachers from the manifold limitations imposed by nature on the application of mathematics to problems in earthwork engineering. As a consequence, more and more emphasis has been placed on refinements in sampling and testing and on those very few problems that can be solved with accuracy. Yet accurate solutions can be obtained only if the soil strata are practically homogeneous and continuous...." This statement about soil mechanics was made by Karl Terzaghi, thirty years ago and applies to a greater degree today to the infant science of rock mechanics. More uncontrolled variables are added to the already many existing in soil mechanics. Variables, such as Macro-discontinuity and in situ stress levels. In no other field of engineering are the problems as site oriented. Presently this site dependance demands the investigator or rock mechanics engineer to get his hands dirty rooting in the muck of a tunnel floor trying to properly install or readout test apparatus in a comprehensive site investigation. This paper discusses such a site investigation designed to determine the problems and solutions inherent in the driving of the Trans Koolau Tunnel. The paper will describe the various types of tests to be performed, how the results are to be used and the interrelation of the various tests themselves.

Jan 1, 1997

By W.J. Atkinson

The first recorded discovery of diamonds in Australia was in 1851 from New South Wales. Subsequent prospecting has shown alluvial occurrences of diamond to be relatively widespread through much of the Tasman Fold Belts of Eastern Australia and production to date is estimated to be some 500 000 carats from a number of 'small alluvial fields. Despite extensive exploration though, no primary rock source carrying significant diamond contents has ever been confirmed in Eastern Australia. Conversely, diamond exploration of the older Western and Central Cratons of Australia over the past 30 years has discovered 12 fields containing 360 kimberlites, lamproites and lamprophyric volcanic pipes, dykes and other intrusives, of which 180 have been confirmed to be diamondiferous. Only one pipe however, the 1200 Ma high grade Argyle lamproite and associated near-by alluvials, has proved to be economically exploitable with current annual production of 40 million carats valued at approximately US$400 million. Production from the open-pit will be sustainable until at least 2003. This paper briefly summarizes the history of diamond discovery in Australia, principal diamondiferous provinces and deposits, current exploration activities and the potential for future discoveries.

Jan 1, 1995

By Keith S. Liddell

he selection of mill design parameters to suit the applica­tion requirements can result in quite different operating parame­ters for each generic type of application, even though the basic mechanical layout of the mills may remain similar. The selection of the type and size of grinding media is very important to efficient and cost-effective operation, and to ensuring that the milled product achieves the required properties. Accordingly, the grinding media selection is seen as an integral part of the mill design. Consideration of the requirement for classification is important in order to achieve the optimum mill and circuit performance. This can lead to the circuit feed not being classified for a steady feed with minimal slimes and a low size reduction ratio. Feed containing on-size particles would be deslimed by open circuit classification. Closed circuit classification is performed where the feed fluctuates. The rheological characteris­tics of the circuit feed slurry can have an influence on mill performance, and needs to be allowed for. A common misconception frequently encountered is the belief that "a mill is just a mill". This is not the case with stirred types of mills, since the operating parameters selected for the mill can have a large effect on the product characteristics. For example, horizontal shaft high speed stirred mills have a com­pletely different grinding action to vertical shaft low to medium speed stirred mills, which results in large differences between the surface area produced at a given product size (Liddell, 1986). Hence, it can be misleading to apply test results or design procedures obtained from one type of mill to other types for scale-up. The Metprotech stirred mill, as applied in the mining and minerals industries, is a low to medium speed vertical shaft mill. The basic design has been discussed previously (Liddell, 1989). Currently, the largest mills that have been manufactured have an installed power of 400 kW. The largest chamber volume at this power is 6000 litres, containing IO t of grinding media. It is intended that the installed power will increase up to lMW as applications requiring larger sizes arise.

Jan 1, 1995

By Drupad B. Desai, Alexander Rosenbaum

In recent years, there has been an increasing use of two-pass tunnel lining system consisting of segmental unbolted expandable precast concrete initial lining and cast-in¬place concrete final lining in the United States. Used so far in soft ground tunneling performed under free air, it often includes a waterproofing or gasproofing membrane placed between the initial and final linings. This paper describes the utilization of this two-pass system for an extension of the Baltimore Metro, constructed in part under compressed air. It offers a description of the extension project, known as Section C; addresses the tunnel lining selection process and the design of the lining elements; examines the effect of the adopted lining system and tunneling technique on the design of the project's major structural components; and describes design modification instructions in order to accommodate constantly changing field conditions.

Jan 1, 1993

By Mohammad Irshad, Larry H. Heflin

INTRODUCTION The planned 166 kilometer (103 mile) Metro rapid rail transit system in Washington, D.C. is being designed and constructed by the Washington Metropolitan Area Transit Authority. At the present time, 112.6 kilometers (70 miles) of this system is in operation and contains 21 route-kilometers (13 miles) of rock tunneling, and 14.5 route-kilometers (9 miles) of soft ground tunneling. An additional 2.4 kilometers (1.5 miles) of single track tunnels in rock are planned and 6 additional contracts will consist of some 8 kilometers (5 miles) of twin tunnel, resulting in 16 additional linear kilometers (10 miles) of single track tunnel in soft ground. The Authority plans, upon its evaluation and the recommendation of the General Engineering Consultant, to include an alternative design incorporating the convergence confinement method of construction known as the New Austrian Tunneling Method (NATM), for Sections E-5, E-6e and E-8a of the E-Route. The Metro system is constructed in a variety of geological conditions and crosses the boundary of two major geographic provinces. Rock tunneling is to the west of this "fall-line" boundary, soft ground tunneling to the east. The soft ground tunneling portions of Metro construction lie in the coastal plain which consist of a

Jan 1, 1987

By Benno Ring

"When designing segmental lining at a cross passage, modern solutions try to bear the loads transferred around the opening within the rings by using shear elements in the ring joints. Commonly used shear systems providing coupling are cam & pocket, shear keys, bicones and steel dowels. These solutions have advantages and disadvantages, but most importantly they have limits in their capacity to stabilize the lining at cross passages. With the help of 3D-FE-analyses for an opening of one segmental ring these different solutions are compared taking various ground conditions into account. As a result the capacity of the individual system is determined. Notice is made regarding the applicability of the system as well as the consequences for the design and the verification. INTRODUCTION The design of the lining at a cross passage is among the most difficult tasks when designing TBM-tunnels. At one time the bedding of the lining disappears due to the excavation behind the lining, at another the ring-structure is interrupted when parts of the lining are removed for the opening. The trick is to transfer the loads around the opening into other segments and to areas of the lining which are still supported by the ground. In the rings immediately at the cross passage this creates a distribution of forces within the segments that strongly deviates from that of the regular lining. The design needs to consider the boundary conditions of the respectively chosen solution for stiffening of the opening and its peculiarities in the modeling as well as in the verifications. In the past segments of steel or an internal strutting of steel (DAUB 2013) placed around the later openings were commonly used, see Figure 1. The application of a strutting from the outside to the rings is restricted to such circumstances when for example a connection from a shaft to the tunnel can be made in suitable ground conditions (Ring and Glomp 2012). Though steel segments provide a robust solution, they are expensive due to their laborious manufacture, the high proportion of construction steel required and the time consuming installation in the tunnel (Häfliger 2013). A strutting of steel requires extensive design and verification. The resulting structure usually weighs several tons and must be erected as well as demounted within the confined space of the tunnel, requiring suitable transport and assembly equipment. The cross section remains restricted, thus causing a bottleneck for TBM operations and hindering the works and installations for the cross passage works."

Jan 1, 2016

By C. Y. Kao, Roger Y. Cheng, C. S. Hsieh

The mushroom-shaped Minghu power cavern located in central Taiwan is 21.2 m (W) by 40.5 m (H) by 127.2 m (L) and is designed to house 4 units of power generating-pumping equipment with a total capacity of 1,000 MW. This paper presents an introduction to the geological conditions at the cavern site; the rock mechanical tests undertaken; the design approach adopted; the construction method and sequence followed; and the instrumentation provided in the roof arch to monitor the behavior of the surrounding rocks. The measured data collected from the embedded instruments will be compared with those obtained from theoretical analyses and presented in this paper. Several technical problems encountered during the construction stage are covered and the solutions of these problems are also described therein.

Jan 1, 1983

By Steven G. Grannes

The Bureau of Mines, U.S. Department of the Interior, has developed a computer image processing algorithm to determine the size distribution of moving taconite (iron ore) pellets. This algorithm interprets line-scan images to measure pellet diameters. Pellet edge detection with a peak light intensity constraint is the basis of this technique. Preliminary error analysis indicates a normally distributed experimental error with a standard deviation of 0.09 and 0.15 for pellet diameters of 0.4 and 0.9 cm, respectively. System accuracy was independent of moving pellet speed below 50 cm/sec. Computer image-based size distributions were found to be in close agreement with standard sieve analysis.

Jan 1, 1986