Search Documents

By Ron H. Schonewille

Experiments were conducted by injecting air-oxygen gas mixtures through a ceramic lance into molten copper matte and measuring the sulphur dioxide content of the offgas. The injection conditions were characterized by measuring pressure fluctuations immediately upstream of the lance and capturing the information on an oscilloscope screen. The parameters investigated were gas flowrate, lance geometry, lance immersion, orifice diameter and melt composition. An overhead nitrogen lance was used in specific tests to create an inert gas blanket directly above the bath surface to inhibit reaction in this region. The extent of oxidation was modeled by separating the gas-liquid contact into three stages; bubble growth, bubble rise and bubble rupture. The contribution of each stage to oxygen utilization was determined by varying the lance immersion and by performing tests both with and without an inert gas blanket. Bubble rise was found to be relatively unimportant, accounting for less than 5% of the total oxygen utilization. Bubble rupture and bubble growth were found to contribute approximately equally, with bubble rupture becoming more important with increasing gas flow rate. This study highlights the importance of reactions taking place above the bath surface in a copper converter.

Jan 1, 1999

By D. G. Schmidt

Tests were conducted on C86200 high-strength yellow brass in order to ascertain the effect of a low level of nickel on the mechanical properties on this alloy. A series of two alloys was studied, one of which had a nickel content of 0.85% and the other with <0.05% nickel. Copper and aluminum content ranged from 62.5% to 64% and 3.2% to 4.6%, respectively. When compared by zinc equivalents, a nickel addition of 0.75% in high-strength yellow brass does not act like copper but raises the tensile strength, 0.5% yield strength and BHN while lowering the elongation.

Jan 1, 1999

By H. Y. Cheng

A pulse column solvent extraction system was evaluated as an alternative to mixer-settlers for the separation and purification of rare earths. The column tested had an inside diameter of 44.5 mm and had 36 sieve plates with a free area of 25%. Pulsing was provided pneumatically using a solenoid valve controlled by a timer so that both pulse amplitude and frequency could be varied. Feed to the column was a mixed rare earth chloride solution containing 10 g RE L-1. The extractant was 5% Ionquest® 801 in Shellsol 2037 diluent. Hydraulic performance of the pulse column was excellent with no propensity towards stable emulsions or crud formation under normal operating conditions. The column was operated in organic-continuous mode with flow rates chosen so that yttrium and the heavy rare earths were extracted with high efficiency while the light rare earths were rejected. Yttrium extraction varied from 83 to 99.2%. Concentration profiles were measured in both the aqueous and organic phases, and, from this data, the height of a transfer unit (HTU), the mass transfer coefficient (Kxa) and the continuous-phase axial dispersion coefficient (Ey) were computed. The HTU ranged from 17-92 an which is within the range of values reported for other (non rare earth) pulse column systems.

Jan 1, 1992

By Weyman Dunaway

This paper will present a description of the development and commissioning of the world?s most efficient process for manufacturing high purity aqueous zinc bromide. The method for making aqueous zinc bromide from metallic zinc and bromine comprises contacting zinc with bromine dissolved in a reaction solvent containing a metal halide salt. The reaction temperature is maintained at less than 60°C. The reaction solvent preferably comprises an alkali, alkaline earth, or transition metal halide; the halide salt preferably comprises a chloride or a bromide. One preferred method includes the step of recirculating the zinc bromide product stream back to the reaction vessel. The reaction vessel can be either a one stage or a multiple stage reactor. The resulting product stream is a high density aqueous zinc bromide solution. The process is so novel that Tetra Technologies, Inc. was awarded US Patent Number 6,036,937.

Jan 1, 2006

By T. R. A. Davey

It is often important in the study of a process to determine whether the limitations are governed by equilibrium or kinetic considerations. Sometimes it is possible to devise a design of the process or the equipment so that the apparent. limitations set by equilibrium considerations are overcome. In this paper, detailed consideration is given to the lead refining processes of sulfiir-decoppering and of vacuum dezincing to illustrate this, and possible implications for other refining processes are indicated.

Jan 1, 2000

By He De-wen

The increasing population and living standard in urban areas, have been accompanied with the growing quantity and composition complexity of rubbish, which are causing well-known social effects of pollution, while rubbish (solid waste) is a recyclable resource. To convert rubbish into useful materials, the essential measure is to carry out sorted collection of rubbish. The preconditions of implementing sorted collection are presented in the paper. 1 Characteristics of rubbish composition and amounts of recyclable contents are basic condition to implement sorted collection. 2 The existing available technologies of recycling, economic benefit from recycling, and disposal scheme of residual rubbish are restrained condition for sorted collection. 3 Public understanding and support to sorted collection are the key to success. 4 The government policies to be favorable for sorted collection is the pledge of success. 5 The establishment of a steady solid waste recycling market is also a guarantee to implement sorted collection continuously. 6 To establish management system of rubbish recycling as soon as possible. Further, the methods and procedure of sorted collection are discussed in detail and beneficial comments and theoretical basis to promote sorted collection of rubbish in urban area are presented; it will contribute reference value to municipal solid waste management.

Jan 1, 2006

By G. St-Amant, V. Cloutier, E. Ghali, S. Jin, G. Houlachi

During the casting of lead-silver anodes, variations in cooling rates result in the formation of an uneven microstructure. The slowly cooled areas (SCA) have a coarser microstructure than that of the remaining part (called "the general zone"). The effect of anode microstructure on the electrochemical behavior was investigated using galvanostatic, potentiodynamic and electrochemical impedance techniques. The results show that the resistances for the two steps of the oxygen evolution reaction on the slowly cooled areas of Pb- Ag anodes are higher than that on the general zone. The double layer capacitance for the first step of the oxygen evolution reaction (OER) and the pseudocapacitance of the second step of OER on SCA are smaller than those on the general zone. The potentiodynamic results show that the amount of lead dioxide formed on the SCA is greater than that of the general zone of the anode. The potential decay curves after 30 minutes of galvanostatic polarization at 45 mA/cm2 show that the corrosion potential of the SCA is 200 mV lower than that of the general zone. This can lead to perforation because of the formation of a galvanic cell with a small anode and a large cathode.

Jan 1, 2000

By Zviad Kovziridze

It is stated that the specific character of SPHTS specimens of TiCx consists in crystal lattice strength reflecting the condition of synthesis in ?burning wave?. The use of roentgenographic and other methods of analysis allow to estimate the effect of the conditions of synthesis causing the carbon sablattice defect on the grinding intensity of TiCx -phases. The study of the kinetics of vibratory grinding of TiCx -phases in ethanol and benzene medium allows to establish high grinding intensity of the phases close to stoichiometry and the possibility of producing high dispersion powders (Ssp 4.5-6 m2/g).

Jan 1, 2006

By K. Noda

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. is carrying out a low cost production using a Tamano Type Flash Smelting Furnace (T-FSF), which is an improved version of Outokumpu Type Flash Smelting Furnace but without slag cleaning furnace and also by developing its own coke combustion technology. Coke combustion technology that is the basis of the system has been improved several times and, at present, it has evolved to a stage where it can be reproduced on the Computer guided system for Coke Combustion in the T-FSF (CCCT) using a general- purpose computer. This CCCT is featured by &apos;its trend control and predicting function, and an operator can freely control the operation parameters so as to control the operation flexibly. We have recently developed an overall energy reduction system covering the Smelting Plant to Sulfuric Acid Plant, which we call an Optimum Low Cost Operation System (OLCO) to reconsider the energy costs including coke, heavy fuel oil, and electric power. In this report, we would like to present the recent operation of T-FSF based on CCCT as well as the optimum energy operation utilizing OLCO system.

Jan 1, 2002

By Ross Baldock, Ross Andrews, Gu Helin, Lan Xu, Markus Reuter, Song Xingcheng

"A commercial lead smelter using Outotec Ausmelt TSL Technology has been successfully commissioned and put into operation at Yunnan Tin Company Ltd operations near Gejiu City, in Yunnan Province, China. The plant was commissioned in July 2010 after three years in the design and construction phase. The process uses a three stage batch process to produce lead bullion and zinc fume, and a slag that is low in metal values. The paper provides details of this lead smelting project, including the theoretical evaluation of the multi-stage process chemistry, engineering design, plant commissioning and the final operation. Comparison of the design targets and actual performance of the plant is emphasized. The fast ramp-up to full production of the largest Ausmelt TSL lead furnace built to date is highlighted.IntroductionIn 2002, Ausmelt and Yunnan Tin Company (YTC) successfully commissioned a smelter to modernise the Yunnan Tin smelter in Gejiu City, Yunnan Province, China. A single Ausmelt furnace was installed by YTC to process tin concentrate and revert materials, to produce YT Brand tin product. The advanced Ausmelt Technology furnace at YTC replaced seven existing reverberatory furnaces and provided a flexible, energy efficient and environmentally beneficial system to complement the world leading refinery facilities of YTC."

Jan 1, 2012

By Shuo Wang, Yu Wang, Bing Xie, Rui Tang, Hong-Yi Li, Kun Wen

"During present converter vanadium extraction process, phosphorus could not be removed from hot metal due to absence of CaO in slag though it is an efficient way for vanadium extraction. In order to improve the phosphorus remove and produce CaO-containing vanadium slag, which could be directly used in subsequent roasting process, during the converter vanadium extraction process, lime dissolution in FeOx-Si02-V203-Ti02 slag was investigated by using a rotating cylinder technique and the slag-lime interface was characterized by SEM/EDS. Results showed that changes in the slag chemistry and phase compositions during the lime dissolution process were similar to that in CaO-Si02-FeOx based slag during the BOF process. The V and Ti in the slag were expected to diffuse into the lattice of2CaO·Si02 solid solution, which formed a rather thinner layer in thickness at the slag-lime interface than that in BOF process, leading to improvement of lime dissolution in the slag.IntroductionVanadium is important material that widely applied in industries. The traditional technique to extract vanadium was to leach vanadium after sodium salt roasting. However, the sodium salt roasting process has several problems including lower yielding rate[!] and environmental pollution[2]. Therefore, the more environment-friendly technique of calcium roasting[3-4] was proposed. In order to increase roasting efficiency of vanadium slag, it is essential to study the dissolution/reaction mechanism between lime and vanadium slag. Many investigations about the dissolution reaction of lime in molten slag have been carried out from the standpoints of rapid slagging to De-Pin steelmaking process[5-6]. However, their studies were focused on BOF slag and the reaction mechanism between solid lime and slag containing vanadium has not been reported yet. In present work, the dissolution process was studied with rotating cylinder technique and the reaction interfaces were observed and analyzed by SEM/EDS to elucidate the dissolution mechanism of lime in vanadium slag. This work was supported by National Natural Science Foundation of China No. 51090382."

Jan 1, 2013

By Benjamin Vidales

Copper in concentrations above 0.5 weight percent in iron and steel causes hot shortness. This tendency is intensified in the presence of dissolved tin above 0.05 weight percent in the alloy. The understanding of the mechanism of removal of copper from molten iron and steel is of industrial importance. In this investigation, we present the experimental results of the removal of copper from molten iron using sulphide flux in the temperature range 1000°-1500°C. The solution thermodynamic properties of binary sulphide melts have been estimated by using the relevant phase diagrams and the behaviour of copper sulphide in these melts is discussed. The kinetics and thermodynamics of the removal reaction are also explained and, the experimental results are also reported showing the equilibrium distribution of copper and sulphur in molten iron.

Jan 1, 1995

By Natasa Mitevska

The distribution coefficients of Ag, As, Au, Bi, Co, Cu, Ni, Pb, Sb, Se, Te, and Zn between copper matte and slag from the reverb furnace No.2 at the Copper Smelter and Refinery, RTB BOR (Yugoslavia), are presented in this paper. The influence of the matte grade on the minor elements distribution coefficients between copper matte and slag is analyzed. The minor elements distribution in the slag phase along the slag melt depth and the furnace length is also determined.

Jan 1, 2002

By Catherine Williams-Beam

Thallium is more toxic to humans than mercury, cadmium, lead, copper or zinc. Its chemical behavior resembles the alkali metals (K, Rb, Cs). It occurs almost exclusively in natural waters the monovalent thallous cation. The solubilities of thallous compounds are relatively high so that monovalent thallium is readily transported through aqueous routes into the environment. The major sources of thallium are the base metal sulfides and precious metal bearing sulfides. Therefore, it is often present as a contaminant constituent in waters emanating from heavy metal sulfide bearing deposits. Thallium can be effectively removed from wastewater to <2 µg/L by reductive precipitation of thallium sulfide. Effective thallium sulfide precipitation requires a controlled solution potential/pH combination. The required potential can be effectively achieved by utilizing a particulate iron slurry or packed column environment. Experimental results will be presented and discussed.

Jan 1, 2003

By Ryokichi Shimpo, Akio Fuwa

"In order to elucidate the present status of process-control technology, survey study has been made on the present process control schemes of representative copper smelting and converting processes in Japan. Conceptual control flow diagrams have been deduced and shown on respective functional reactors, i.e. drying, smelting, converting and fire-refining units, where the objective OUTPUT items are correlated to the INPUT variables through respective CAUSE-AND-EFFECT RELATIONSHIPSFuture view has been also discussed on several feasible and desirable improvement and refinement ~n measurements and control system for better copper smelting and converting operations.INTRODUCTIONIn other to seek for the better and efficient operation in copper smelting and converting process, survey study has been first conducted on the present process-control schemes of respective functional unit processes, i.e. drying, smelting, converting and refining unit processes, of representative copper production processes in Japan. Conceptual process flow chart of control scheme has been then deduced where output items are correlated to input items through the respective cause-and-effect relationships.After this survey study, future view has been discussed on the feasible and desirable improvement and refinement in the measurement and control system in these processes. Emphasis has been placed on the better and precise measurements of temperature, oxygen partial pressures in respective furnaces and end-point in converting and refining unit operations."

Jan 1, 1989

By V. L. Stolyarova

As part of an effort to develop the fluoride electrolysis route for the production of rare earth metals and alloys, a study of the thermodynamic properties of DyF3 has been carried out by Knudsen cell mass spectrometry. A quadrupole mass spectrometer QMS 420 was used in conjunction with the Knudsen cell arrangement. The experiments were carried out in the temperature range 1280-1440 K. Vaporization was carried out from platinum, molybdenum and tantalum cells. The Dy*, DyF+, DyF2+ fragment ions and the DyF3 parent ion were identified in the mass spectrum of the DyF3 vapour. The DyF, vapour pressure was obtained by the complete isothermal vaporizadon method as well as the ion current comparison method, and the enthalpy of sublimation of DyF3 was evaluated. From the DyF3 vapour pressure data obtained at different temperatures, the enthalpies of formation of DyF3 in the gaseous as well as condensed phases have been evaluated. The experimental data are compared with the thermodynamic information available in literature.

Jan 1, 1995

By Zhijing Zhang

Long-term thermal stability of ionic liquids is essential for reliable performance of ionic liquids in any engineering applications. TGA studies were carried out on a series of ionic liquids with different cations and anions such as 1-butyl-3-methylimidazolium chloride ([C4mim]Cl), 1-hexyl-3-methylimidazolium chloride ([C6mim]Cl), 1-hexyl-3¬methylimidazolium tetrafluoborate ([C6mim]BF4), 1-hexyl-3-methylimidazolium hexafluorophosphate ([C6mim]PF6), 1-octyl-3-methylimidazolium hexafluorophosphate ([Csmim]PF6), and 1-butyl-3-methylimidazolium bis(trifluromethanesulflonyl)imide ([C4mim][Tf2N]). The short-term thermal stability of ionic liquids was evaluated by measuring the onset temperature of decomposition of ionic liquids, and the long-term thermal stability of ionic liquids was also evaluated by weight loss of ionic liquids over a long period of time at various temperatures. The experimental results showed that the long-term thermal stability of ionic liquids decreased with increasing temperature and was significantly lower than the onset temperature of decomposition of ionic liquids.

Jan 1, 2002

The presence of clay adversely affects the floatability of copper and molybdenum during processing porphyry copper/molybdenum ores. In addition, reagent consumptions are much higher than when treating clay-free ores. Ores containing kaoline, brammollite, illite and montmorillonite were examined in the laboratory to determine how clay minerals affect the floatability of copper and molybdenum, and to find a possible solution to alleviate the harmful effect of clay slimes. It was demonstrated that the presence of clay mostly affects floatability of coarse and middling particles, and reduces selectivity. The results of the research work showed that there may be several possible ways of reducing the detrimental affects of clay slimes on flotation, some of which include a) use of alternative flowsheets, b) flotation at reduced pulp density, and c) the use of special frothers. The applicability of the findings in plant practice are discussed.

Jan 1, 1999

By Kenji Monden

"The creep properties of tin-based lead-free solders Sn3.0AgO.5Cu and SnO.7CuO.1Ni and lead solders 10Sn90Pb and 50Sn50Pb were investigated at temperatures between 298 K and 398 K. The creep-rupture time decreases with increasing initial stress and temperature. The analysis of the solder creep curves uses the Omega method. The creep rate E is expressed by following formula: 1n ? = 1n ?0 + O?, where ?0 and O are experimentally determined. The parameter Eo increases with increasing initial stress and temperature. The activation energy for ?0 is 108 kJ/mol for Sn3.0Ag0.5Cu and 85 kJ/mol for SnO.7CuO.INi. These energies suggest that the lattice diffusion of tin is dominant. The energy of 1OSn90Pb is 37 kJ/mol and that of 50Sn50Pb is 67 kJ/mol. The creep-rupture time is calculated using the parameters, ?0 and O. The calculated creep-rupture time is in good agreement with the measured creep-rupture time.IntroductionLead-free solders are replacing traditional tin-lead solders as part of a major trend toward protecting the earth's environment. However, tin-lead solders are currently needed for a high temperature range. Since creep is the main deformation mechanism in solder joints, understanding a constitutive model for creep and examining creep data for solders are important for reliability analysis of solder joints. A steady-state creep equation is generally used for solders [1,2], and it supposes that the secondary-, or minimum-, creep rate occupies the entire creep life. However, secondary creep accounts for only about 15 % to 40 % of the entire creep life for solders. Thus, the equation may not represent the entire creep life."

Jan 1, 2012

By Shunichi Ajima

PT. Smelting Co. was established in February, 1996 to construct and operate the Gresik Smelter and Refinery. The construction work of first Copper Smelter and Refinery in Indonesia was completed in the end of August, 1998 and it was put into the integrated test operation in December, 1998. Gresik Smelter and Refinery is designed to produce 200,000 tpy of copper cathode from copper concentrate supplied from Grasberg Mine of PT. Freeport Indonesia Company in Irian Jaya, Indonesia. As by product 592,000 tpy of sulfuric acid, 382,000 tpy of slag, 31,000 tpy of gypsum and 480 tpy of slime will be produced in the full operation. Major processes applied at Gresik Smelter and Refinery are: Smelter: Mitsubishi Continuous Copper Smelting and Converting Process ( Mitsubishi Process ) Anode Casting: Continuous Casting of Copper Anodes with the Hazelett Twin Belt Caster Refinery: ISA Process Acid Plant: Lurgi Mitsubishi Double Contact Process

Jan 1, 1999