Search Documents

The profitability of gold placer mining operations is determined by more factors than many placer miners recognise until too late. This study is based upon field trips to examine the efficiency of mining and transportation of gravels to a wash plant by bulldozer and truck. At the examined open pit mining operations gravels were washed using water canons, derockers or scrubber trommels. The objective of this study was to determine the relationship between unit costs and power requirements for gravel mining and processing. The author conducted a number of time and motion studies at four open pit gold mines, including the Maly Patom Creek, the Nizhny Patom, the Taimendra Creek and the Kadali-Makit in the Bodaibo District, Irkutsk Region and collected and processed field data. As a part of the study significant correlations were determined and empiric regression equations derived between: power requirements (Ep) and unit cost (Cp) for gravel processing; and total power requirements (Et) and total unit cost (Ct) for gravel mining, transportation and processing. Based on the results of the study it was proposed to modify the current mining procedure methods and to replace water cannons at the Maly Patom Creek with a PPM-5 derocker. Introduction of the proposed technology resulted in 2004 in US$385 000 mining cost reduction at the Maly Patom Creek over a short-time Siberian mining season.

Jan 1, 2007

By R. S. Montgomery

Laboratory experiments simulating rock drilling were conducted on a number of commercial grades of tungsten carbide in order to determine their wear rates when they are used as inserts in percussive rock drill bits. The test rock was Barre granite and tests were made at conditions similar to those of the carbide buttons near the periphery of a large, down-hole, button bit. In addition, some wear rate measurements were made at a low blow energy. Wear rates of these carbide buttons were an extremely sensitive function of their cobalt contents and hardnesses and were proportional to e-°.57Hup to a hardness of about 91 RA. The point of minimum wear rate, which occurs at about 92 RA, corresponds to the point of maximum compressive strength. Modern percussive rock drill bits have inserts of cemented tungsten carbide on their wear faces. These inserts have drastically reduced bit wear in comparison to that of earlier all steel bits. The most common cemented carbide grade used in percussive rock drill bits contains about ten weight percent cobalt, although grades containing more or less cobalt are also used. Contrary to the case with carbide in metal-cutting tools, alloying materials are rarely used in mining grades. There are a number of designs of rock bits in current use. The most common form is an X bit which has four chisel-form radial wings. The button bit is another important design and one which has been recently developed. This design uses a flat steel face studded with relatively small hemispherically tipped carbide buttons. These types are illustrated in Fig. 1. Studies have been made of the sliding wear of cemented tungsten carbide on rock 1-4 and multiple-impact fracture', 5-6, b~t there has been comparatively little published on the percussive wear of this material although the wear of the impact face is the most important. There is some available data on the rate of dulling of rock bit inserts in actual drilling 7 but no laboratory studies. Sliding wear studies are useful for understanding the wear of coal and mineral cutting tools and gauge wear of percussive drill bits. but the

Jan 1, 1970

By Haukka M. T

A new low-dilution fusion method which has been successfully used for accurate determination of the major oxide components of silicate rocks, is applicable to rapid, accurate determination of trace or minor eiements in mineral exploration samples. Limit of detection is in many cases less than 5 ppm. Either rapid, approximate measurement and calculation methods (suitable for geochemical exploration), or more accurate methods (applicable to orebody evaluation studies) may be used.Rapid methods are described for nickel in rocks and sulphides containing 10 ppm to >2 per cent Ni, and for gallium. The rarely-determined element gallium is an example of a constituent which may be easily investigatedby XRF using the LiB02 fusion disc, which is a permanent, easily-stored analytical sample available for later rapid or accurate analyses. The method is applicable to over 30 elements at levels encountered in mineral exploration.

Jan 1, 1978

By A. Bamber

Canadian leadership in a global mining context will depend not only on entrepreneurship and best practice but also on technological innovation. This paper argues for more ambition and commitment to R&D for technological innovation in Canadian mining. It focuses on underground hardrock mining, where past R&D initiatives have simply not stood the test of time, and it is important to examine why. Concerns arise because industry’s commitment to R&D has not been sustained over time. Innovation through exploration, processing, and environmental technologies has been more significant. Meanwhile, R&D capacity and synergies in government institutions and universities have not been exploited. There is a need for more commitment, coordination, and collaboration by industry, governments, and universities. This paper examines some corporate models that have achieved sustainable innovation, along with some that have not. A strategy for innovation is discussed that relates to culture, commitment, coordination, and collaboration.

Jan 1, 2005

By Sergio Neves Monteiro

In the present work, a ceramic foam elaborated with illitic clays was characterized. Properties related to density and compression strength were determined in samples fired at 1300oC, a temperature that permits the clay structure to generate and retain gases that will produce the foamy structure. The microstructure of the ceramic foam was studied by X-ray diffraction, scanning electron microscopy and mercury porosimetry. The results showed that the ceramic foam presents a bulk density of 0.38 g/cm3. The microstructure is formed by large open pores, quartz particles and vitreous phase.

Jan 1, 2006

By N. Jayaraman, V. Srikant, A. Radhakrishna

Addition of a 500 MW unit to the existing units at Ramagundum Thermal Power Station requires blasting of large volumes of rock very close to sensitive installations like Turbo generator, Generator transformer and Power cycle equipments. Levelling of the areas and excavations for footings are, therefore, to be carried out cautiously. The existing sensitive installations should be protected against ground vibrations and flyrock. The paper describes the details of a few of the many blasts carried out successfully wherein the ground vibrations were restricted and flyrock was avoided.

Jan 1, 2003

By M. M. K. McCrank

"PRACTICAL SAMPLING TECHNIQUESIt is important to achieve reliability when sampling heterogeneous materials where there is a difference in composition, and non random distribution of the constituent particles. Throughout the design, construction and installation of sampling systems it must be borne in mind that the sampling point must be capable of:-allowing each particle in the stream an equal opportunity to be sampled.-accepting and collecting as large a volume or mass of material as necessary to satisfy the requirements of particle counting statistics.-establishing a sampling plan so that the sample is representative of the whole to a defined standard of accuracy.Design ConsiderationsFactors that may influence the design of the sample point include:-the mass, or volume flow rate of the material being sampled-the size and shape of the material or flowing stream-the physical condition of the material being sampled (i.e. temperature, wetness, size consist, density).-the chemical composition of the material being sampled -the location of the sample point and the space available for installation, extraction, reduction where necessary, secondary sampling, and return of the sample rejects downstream.-whether the process to be sampled is in an existing plant or one yet to be designed and built.-ease of access for servicing and maintaining the equipment.-whether the sampled material must be collected continuously or intermittently.-whether an existing sampling method is likely to be adequate or whether a new technique has to be developed."

Jan 1, 1989

By Xiao Caimei

The method of Substance Flow Analysis (SFA) provides a helpful tool for the study of the industrial metabolism of a certain metal within a regional level, such as copper, lead etc. In this paper the flows and inventory of cobalt in China, 2008, were traced with the STAF model, and the situations of production, fabrication and manufacturing, use and waste management in China were introduced. The result revealed that the resource of cobalt in China was so poor that a large amount of cobalt material or cobalt products needed to be imported, and there was lack of recycling of cobalt resources.0

Jan 1, 2010

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By W. H. Tomlinson

The fourteenth National First-Aid and Mine Rescue Contest we;; held at the State fairgrounds, Columbus, Ohio, October 2, 3, and 4, 1951. The meet, the first such event in 21 years, was under the auspices of the Bureau of Mines, United States Department of the Interior, and the Joseph A Holmes Safety Association and was sponsored by the National Coal Association, the United Mine Workers of America, and various State mine-inspection departments. The cooperating agencies that contributed to make the meet a success, in addition to the National Coal Association and the United Mine Workers of America, were the Kentucky Department of Mines and Minerals, Ohio Division of Mines, West Virginia Department of Mines, Pennsylvania Department of Mines, and the Columbus Convention Bureau. SUMMARY Fourteen teams from 6 States participated in the mine rescue contest, and 55 teams from 9 States competed in the first-aid contest. Only one of these teams entered as a combination team, that is, participating in both the mine rescue and first-aid contests. The States represented and the number of teams from each State are listed in table 1.

Jan 1, 1953

By P. J. Baguley

The model has been developed on the basis of the observation that the partitioning behaviour of a particle is related to its calculated terminal velocity. It utilises a theoretical calculation of the terminal velocity of each particle class. This is then correlated with the observed partition data for a plant separator using empirically-derived functions of operating conditions which take into account effects such as bath turbulence, holes in drum lifters and feed arrangements. The model successfully decouples the effects of medium density and viscosity and is appropriate for any bath-type separator. The correlation between calculated terminal velocity and actual partitioning behaviour was established and modelled using data obtained from two Wemco drums treating Fe and Mn ores. The model can be used to predict the prevailing size-by-size partition curves and the separation (product grades/recoveries) given the washability of the feed and operating conditions. Simulations are used to show that, for the treatment of Fe ore, there is a maximum medium density beyond which product grades fall and that this maximum decreases as the proportion of magnetite in the medium increases. This is attributed to the dominant effect of viscosity at higher medium solids concentrations

Jun 18, 1905

By F. Tailoka

Bi was electrorefined from alloys containing 10-90 wt% Pb, together with Cu and Ag as minor impurities, in a basic cell and in a recessed-channel cell with 27.5:72.5 NaCl-PbCl electrolyte at 450-470 degrees C and 10 000-20 000 A/m2. The voltage in the basic cell was as high as 9 V, with some carryover of Bi to the cathode observed, whereas in the recessed-channel cell it was as low as 285-635 mV. Flow patterns observed in a room-temperature model indicated that the recesses provide both static liquid hold-up and good mixing of the alloy, enhancing cell performance in combination with the reduced anode-cathode distance of 0.90 mm. The purity of the resulting anode product is as high as 99.9%

Aug 1, 1995

By M. J. Ferrante

Laboratory-scale tests were undertaken to examine several electrolytes for possible use in separating nickel and cobalt from products being prepared at Nicaro, Cuba. The most extensive work was done with nickel sulfate-ammonium fluoride, ammonium fluoride, ammonium sulfate, and nickel sulfate-boric acid electrolytes. All four electrolytes exhibited some selectivity for dissolving nickel carbonate from Nicaro basic carbonate used for regeneration. The nickel sulfate-ammonium fluoride electrolyte exhibited less selectivity for dissolving nickel carbonate from Nicaro basic carbonate than it did from synthetic mixtures. Ammonium fluoride leaching experiments showed that a low concentration and high temperature gave a good nickel extraction with C. P. reagents; however, this was not confirmed in tests using Nicaro basic carbonate. Electrolytic tests employing ammonium fluoride leach liquors gave no further separation, since approximately 90 percent of the cobalt was deposited at the cathode with the nickel.

Jan 1, 1958

By S. J. S. Ferreira

Anglo American Platinum's Khomanani 2 shaft changed over from down-dip mining to breast mining in 2004. The changeover was made to ensure that production targets were met, as it was said that predevelopment for down-dip mining was not fast enough to sustain the required ore reserves; nevertheless, production performance did not increase as expected. In this study a trade-off was performed between down-dip mining and breast mining on the Merensky Reef at Khomanani 2 in order to find the most suitable method for mining the Merensky Reef. Data was gathered by means of a literature survey, underground observations, and interviews with personnel as well as data from various departments on the mine. The two mining methods were studied and then evaluated in terms of the following criteria: safety, mining rate, cost and other factors which were identified as the main drivers of the mine. A scaling system was used to rate the performance of the two mining methods. Analysis of the results shows that down-dip mining and breast mining have the same safety performance ratings. Breast mining has a better mining rate performance than down-dip mining. Breast mining was found to be costly in comparison with down-dip mining, which has a good cost performance rating. The overall ratings of the two mining methods are very similar, with down-dip mining achieving a rating of 76 and breast mining 75.5 out of an optimum 102. Khomanani 2 currently practices breast mining, and with such a slight difference in performance rating between the two methods, it will not be worth changing over to down-dip mining as production is likely to be adversely affected during the changeover. Down-dip mining does, however, have potential for improvement in its performance rating. Further studies focusing on the improvement of the mining rate performance for down-dip mining are needed to see if this potential can be realized. If significant improvement can be made in the performance rating for down-dip mining, a changeover to down-dip mining can be reconsidered.

Jan 1, 2012

By D. deV. van der Spuy

A procedure for optimizing the secondary cooling zone of continuous casters is proposed and illustrated by a billet caster example. The procedure consists of quantifying deviations from the required conditions of the secondary cooling zone?as far as temperatures, metallurgical length and reheating are concerned?by means of a ?cost function?. The optimal spray settings are then found by minimizing the total ?cost?. The billet caster examples serve to emphasize the importance of specifying the required conditions in a consistent manner. Some envisaged practical limitations of this approach are discussed.

Jan 1, 1999

By Sam X. Yao

The underwater concrete technology has historically evolved largely through a trial-and-error process of constructing marine works. Many outstanding examples exist of high quality concrete placed underwater. However, failures also occurred and led to excessive cost and/or schedule overruns. These failures were largely due to improper concrete mix design or improper placement. The problems may have occurred because proper underwater concrete construction techniques and experience have not been widely disseminated. This section focuses on technical issues of underwater concrete mix design, concrete production and placement, and quality control.

Jan 1, 2013

By David Siskind

The authors studied small seismic exploration blasts for vibration characteristics and effects on structures in Mexico. Obtained were 267 three-component recordings of ground vibrations and structure responses from 62 test blasts at six single-story masonry structures. Charges were 4.55 kg (10 lb) of Vibrogel expolsive at depths of 20 and 30 meters. Initial blasts were 240 meters distant and proceeded towards the structures to as close as 5 meters. All blasts were in soil media in two basic types of terrain, low saturated areas and upland dry areas. Structural inspections were before, during, and after the test blasts.

Jan 1, 2002

By A G. Cuison, B V. Andam

Three well-known copper and gold deposits in northern Luzon, Philippines are located in the Mankayan Mineral District. These are the Lepanto Copper-Gold Deposit, the Far Southeast Porphyry Copper Deposit and the newly discovered Victoria Gold Deposit. The latter discovery led LCMC to shift from a predominantly copper mine to a gold mine. The pre-Eocene Lepanto basement andesite and the middle Miocene Balili volcaniclastic sequence underlie the Mankayan Mineral District. They are intruded by tonalitic to gabbroic Bagon Intrusive followed by diorite-quartz diorite intrusions. Diatreme emplacement of late Miocene-early Pliocene Imbanguila dacite pyroclastics and porphyries took place much later. Faults in the district mostly form a conjugate fracture pattern dominated by north and northwest trending shears, east-west trending extensional fractures and few north-south trending fissures. Victoria is an epithermal gold-base metal rich quartz vein deposit. The veins occur along tensional structures and it is common to observe crustiform and banded features among the sulphides and gangue minerals. It is an open space infilling type of mineralisation. The Victoria vein systems are divided into zones based on continuity. In each zone are major veins and associated spits. Dacite pyroclastics and porphyries predominantly host the major veins with a few narrow veins hosted by the Balili volcaniclastics and the Lepanto metavolcanics. The veins generally trend east-northeast with 75 - 80 dips towards the south. The longest vein can be traced fairly continuously for a horizontal distance of about 600 metres. The vertical persistence of major veins exposed on three level drives has a range of 150 metres and can reach as much as 400 metres based on drill hole intercepts. The vein widths vary from two to eight metres. Right lateral movements of either the NW or NE shear faults could have produced the east trending tensional fractures. The development of ore shoot patterns was recognised and has been helpful to the mining operations. Cymoid loops with defined pinch and swell features are noted both laterally and vertically. Complementing the structural pattern is the distribution of gold values along veins where lateral and vertical continuity is also observed. Gold is associated with quartz, sphalerite, galena and chalcopyrite. In relatively high gold zones, the abundant sulphides are sphalerite and galena. In relatively high copper zones, there is an abundance of chalcopyrite and tetrahedrite. Galena is always associated with sphalerite but less in abundance. Chalcopyrite occurs either as separate bands from or associated with sphalerite-galena. Chalcopyrite and tetrahedrite appears contemporaneous with sphalerite and galena but in some portions the former cuts the latter sulphides. The predominant gangue minerals are quartz, carbonates and gypsum. Rhodochrosite is the predominant carbonate gangue. Few sulphides are found in the carbonates. Gypsum (anhydrite) is found cross-cutting early mineralisation. It carries very few sulphides. The alteration halos around veins are relatively narrow. In an outward sequence, the silicic alteration occurs very near the veins, followed by sericitic-argillic alteration then to propylitic zones. It is also common to observe veins bounded by propylitic alteration. Preliminary paragenetic studies show apparent three stages of mineralisation, the early-quartz (-gold) stage followed by a carbonate stage and a late-gypsum stage. The abundance of base metals relatively decreases towards the gypsum stage. The Victoria gold deposit could have some genetic associations with the Lepanto Cu-Au deposit and probably indirectly with the FSE porphyry system. It is relatively apparent that the Victoria quartz-gold-base metal veins could have occurred similarly as the quartz-gold roots overprinting the Lepanto enargite mineralisation. This overprinting signifies the waning stages of the entire hydrothermal system.

Jan 1, 1999

By Maria I. De Rosa, Charles D. Litton

The National Institute for Occupational Safety and Health (NIOSH/PRL) conducted a series of large-scale experiments to evaluate the effectiveness of optical flame detectors, photoelectric smoke detectors, and combined ionization and photo­electric smoke detectors for rapidly detecting mining equipment cab fires. The detec­tor alarm times were then used to trigger the discharge of a fire inerting system inside the cab to suppress cab material fires. This paper discusses the types of fire detectors tested, the experiments that Were conducted, and the results that were obtained. Con-" elusions are that rapid detection of equipment cab fires can be achieved to trigger the discharge of a fire inerting system inside the cab to protect the operator in the cab.

By J. Drzewiecki, J. Kabiesz

Coal mining using longwall methods of mining can lead to intense disturbances of undermined roof strata. The disturbances may extend beyond the extraction area and the resulted rock mass deformations will appear differentiated. In the case of stiff and undermined roof strata, the energy stored in these rock masses may be frequently dissipated in the form of high-energy seismic tremors. Such events can occur if these strata should fail or „free themselves” either from the constrainment of rock environment or from adjacent strata. It has also been found that the amount of the stored energy closely depends on the size and/or slenderness of these strata. Thus, it would be possible to apply specific preventive measures to reduce the energy of mining – induced seismic tremors. The methods are based on artificial disintegration of the structure of energy – storing strata. One of the most efficient methods is a method of directional hydraulic fracturing, which is regarded as an alternative solution from the traditional blasting and hydraulic methods.

Jan 1, 2003