Search Documents

By T. Wulleman, M. Ansriou

Integrity testing is a primary quality control check on a product that is for the most part not accessible to visual examination. Their cost can be expensive when using direct methods of inspection (like coring a pile) or more economical when using indirect methods (e.g. acoustic testing). All indirect methods operate by “inference” which means that they do not directly measure the defect of integrity. Indirect methods measure the variation of physical values (temperature, impedance, speed, ect.) correlated to the integrity of the pile allowing the detection of integrity defects, although these methods do not allow for the characterization of the defect. 1. INTRODUCTION Cast-in-place piles are particularly prone to integrity defects. The reasons for this are multiple, including lack of high quality of contractor workmanship, experience and supervision necessary in construction, variable soil and groundwater conditions on site, etc. Furthermore, visual inspection of the finalized pile is usually impossible. Therefore, special care has to be taken both during the execution process and during the subsequent quality control campaign to detect any defects of executed piles. Today, a lot of methods do exist to assess pile integrity. It is thus essential to understand the mechanism governing those devices to both make an engineering choice of the pile integrity testing method and to interpret correctly the provided results. 2. QUALITY IN PILE FOUNDATIONS 2.1 Pile anomalies A pile having an anomaly is a pile which has a different behavior from what is normally expected. The presence of a pile anomaly does not necessarily imply that a pile cannot be used for its intended purpose (Gordon & Chapman 2004). An anomaly can be considered as a defect, or a “performance” depending on the ability of the pile to fulfil the following three criteria (3C): C1 - Meet the Service Limit State (SLS) requirement and support the proposed working load without settling more than admissible by the superstructure ; C2 - Meet the Ultimate Limit State (ULS) requirement and carry a specified load with an adequate factor of safety against failure ; C3 - Remain durable throughout the design life of the structure such that the pile is not affected by time dependent activities (chemical attack, corrosion of steel reinforcement, ect.), which would jeopardize its ability to maintain its compliance with the first two criteria.

Jan 1, 2019

By Jamey Rosen

A Project Information Management System (PIMS) was developed to manage and analyze QC data at the Herbert Hoover Dike Rehabilitation Dam Modification Cutoff Wall (owned by the Jacksonville District of the United States Army Corps of Engineers). A special feature of this PIMS was its geospatial component. Data collected from Bauer drill rigs were automatically “geoprocessed” into threedimensional features representing the predrill, jet grout, and Cutter Soil Mixing panel elements, as well as calculated verticality and overlap metrics. These features were visualized in interactive planimetric, profile, and 3D views that facilitated several quality control activities during the project.

By Sandeep Pattnaik

Spring stiffness of soil and rock at different depth is often required for a pile structural model. If the pile is rested in multiple layers of soil, then it is rather more complex to simulate the soil in a structural model. The spring stiffness will vary based on density of soil strata over the depth. When a pile is socketed in weathered rock followed by a soil layer, a sudden change in subgrade modulus can influence the pile deflection drastically. Determination of soil spring and simulation of the pile in this condition required correct interpretation of subgrade modulus. The conventional approach of pile spring calculation underestimates the spring stiffness by ignoring underlaying stiffer layers. A finite difference method (FDM) of analysis can reasonably estimate the p-y of soil / rock based on subgrade modulus of each layer. However, the transition between the layers can be better simulated as per the deflection pattern of the pile. The lateral deflection of the pile is mainly dependent on the stiffness of soil layer surrounded by the pile. Generally, the lateral influence of a pile varies from 4D to 6D depending on the soil type. Therefore, soil spring stiffness around the pile would require special attention of a Geotechnical engineer to avoid uncertainty in the prediction of pile behaviour. In this paper, emphasis has been given to develop an approach for pile spring stiffness design. A standard software program LPile has been used to develop p-y curves of soil and rock layers at different depths and then converted to soil/ rock springs over the depth. Modulus of Subgrade Reaction as given in IS 2911 (Part2) was also used to correlate the spring value for different type of soil. Obtained analytical results were compared with full scale field trial for lateral deflection of pile. A good agreement between these two approaches has been established. The effect of soil structure interaction in the structural model shall be simulated by assigning an equivalent vertical and horizontal soil spring, which is developed by Winkler’s soil spring approach. A simplified design principle for calculating the pile spring is discussed in this paper. This approach has been extensively used in Mumbai metro elevated line pile design.

Nov 1, 2022

By Michael J. Marasa

"Geotechnical engineering and construction primarily relies on the subsurface characteristics of the particular site; however, obtaining both accurate and precise information on those features is challenging due to the numerous factors involved in testing procedures used to analyze varying site geology. This includes a detailed and thorough geotechnical investigation to understand the site conditions, allowing the implementation of the most practical and economical solution.This paper presents a case history of the installation of wick drains and construction of aggregate piers on the site of a large facility to be constructed in Memphis, Tennessee. Throughout intensive subsurface investigations, highly variable soils were encountered, requiring settlement control and increased bearing capacity. This paper will discuss the design and installation of the systems constructed, and procedures and execution of the work to ensure design specifications were achieved.BackgroundA 1.4 million square foot expansion directly adjacent to an existing 1.1 million square foot distribution facility in Memphis, Tennessee was planned to serve as a centralized facility for increased production. The first phase of construction included an 858,000 square foot warehouse and parking lot for approximately 400 trucks to the north of the existing structure. The anticipated column load for the warehouse was 125 kips; slab design bearing pressures ranged from 200 to 500 pounds per square foot (psf) and elevations ranged from EL. 264 to 282. Parking lot elevations ranged from EL. 264 to 290, requiring a design life of 10 years with an estimated 100 in- and out-bound trucks daily and maximum weight of 80 kips per truck. The second phase of construction took place east of the existing structure, and included a 794,000 square foot multi-level warehouse, a 100,000 square foot office, and additional employee parking. The anticipated column load for the second warehouse was 225 kips and slab design bearing pressures ranged from 200 to 500 psf. Elevations ranged from EL. 267 to 282. Anticipated column loads from the office were 25 125 kips, with slab design bearing pressures ranging from 100 to 200 psf. Due to the varying elevations within each planned footprint, up to 18 feet of new fill was required to match the existing structure’s finished floor elevation (FFE) at EL. 282."

Jan 1, 2017

By Joseph A. Sopko

The first documented procedures for designing frozen earth structures are over 50 years old, implemented long before the introduction of the Finite Element Method (FEM). Since that time, the development of three-dimensional models has made the traditional and often over-conservative methods relatively obsolete. This paper discusses a new approach that is largely dependent on the analysis of internal stresses with the frozen structure and comparison to frozen soil laboratory tests. A specific design process is discussed related to initial field investigation, laboratory testing, structural and thermal analysis, and performance monitoring. The design results are compared to case histories in the field that verify the procedure. BACKGROUND One of the first documented methods to designing frozen earth retaining structures was by Sangar (1968). Methodical refinements were published by (Harris 1995) and published by the International Symposium on Ground Freezing in 2002 (Andersland et al. 1991). The structural design or thickness of the frozen mass was based on the unconfined compressive strength of the frozen soils. Two simple equations for determining the thickness of a frozen shaft are shown in Fig. 1 and the first two equations below.

Jan 1, 2019

By Emre Turk, Suat Gullu, Candan Gokceoglu, Ahmet Sirri, Asli Can

In this study, the ground improvement application applied under the live railway bridge's approach embankments in Sivas, Türkiye was investigated as a case study. The soil profile is mainly composed of orangish conglomerate, clay, silty sandy clay, and under claystone, and mudstone units in the study area. As a soil improvement method, the Deep Soil Mixing (DSM) technique based on the principle of simultaneous mixing the ground while injecting with the water-cement mix, was selected. The application of DSM columns is designed to be 45 degrees horizontal, in order to reach the deepest point of the soft clay units for better improvement against settlement. The core samples were taken from the DSM columns and the compressive strength tests were performed in the laboratory. The results were higher than the minimum designed values. It means that inclined DSM columns were applied successfully, and the excessive settlement problem was solved.

Oct 1, 2022

By Andreas Andenæs, Arne Schram Simonsen

"AbstractThe Tresfjord bridge is with its variety in foundation concepts and difficult soil conditions one of the most geotechnically challenging projects in Norway at the time. The project comprises design of large concrete caissons, steel core piles through large rock fills, and closed end steel pipe piles in up to 40m water depth driven in very hard moraine. Test piling has also been conducted to check feasibility of the concept, and PDA measurements have been used to verify sufficient capacity of piles. FactsThe Tresfjord bridge is part of the new export road from Ålesund to Åndalsnes on the North-West coast of Norway built by the Norwegian Road Administration. The bridge will reduce travel time with about 30 min between the cities, see Figure 1. The bridge is planned to open summer 2015.The Bridge crosses the Tresfjord and will be 1290 m long. The bridge is built as a free cantilever bridge and will be resting on a total of 20 nos. of foundations, where two are abutments resting on steel core piles, three are casted directly on bed rock and 13 are foundations resting on steel pipe piles. The last two foundations holding the main span will be concrete caissons resting on bed rock and moraine. Figure 2 shows a 3D model of how the finished bridge will look. Multiconsult AS is responsible for design and pile supervision , while the Joint-Venture Bilfinger-Tresfjordbridge ANS is responsible contractor.Soil ConditionsPercussion soundings and sampling together with coring have been performed in the individual foundations using a small geotechnical equipped vessel. Acoustic and refraction seismic profiling have also been carried out to tie in the layers between the boreholes.The soil conditions are varying over the length, but are in general dominated by a soft top layer (2-4 m) of sediments over very hard moraine with occasionally large boulders. Piles in the two foundations closest to shore on the western side of the bridge are piled to bed rock with penetrations up to about 27 m in soil.Water depth varies from about 10 to 40 m for the piled foundations. Figure 3 show how the topography of the seabed varies over the bridges length."

Jan 1, 2014

"The development of non-destructive testing (NDT) methods for deep foundations occurred in several parts of the world, gradually coming together into the present state of the art. The compilation of this brief NDT history is the best effort of several knowledgeable members of the Deep Foundations Institute (DFI) Drilled Shaft Committee, coupled with the recollections of several historically important contributors to the science. It is not intended to be exhaustive, but rather concentrates on the origins of the methods in common use and on which this manual focuses.Modern NDT methods, and the spread of knowledge about them, have expanded through application to real foundations projects by the original researchers, sometimes inspired by their own curiosity, sometimes to respond to the cost and time limitations imposed by static testing, and sometimes to address the questions raised on research projects funded by large government agencies such as the Federal Highway Administration (FHWA) in the USA, and various European transportation agencies. Initial attempts were primitive by today’s standards, and equipment limitations often restricted successful application to relatively simple cases. As electronics improved and confidence in them increased, the early researchers began commercial promotion of their methods, published their findings in professional journals, and shared experiences at conferences held by such groups as the DFI, the International Association of Foundation Drilling (ADSC), the International Conferences on the Application of Stress-Wave Theory to Piles and other venues such as ASCE and Transportation Research Board (TRB) conferences.NDT methods were developed to fill a need to assess the quality assurance of deep foundation elements. New pile types and higher design loads prompted engineers to verify the safety of their foundations via additional testing during construction. Static load testing was the traditional method to assess performance, and this method has been used for centuries and perhaps even millennia.Relatively recent alternatives to static load testing for determining the capacity of drilled shafts include the bottom load test method. This method uses a jack embedded in the lower portion of the pile (bottom load test) and was first reported to be used from Canada in the early 1970’s (Gibson& Devenny 1973). The concept immediately caught on in Israel, where it was used as a quality control measure for small-diameter piles drilled in rock (then a new technology). The method was later patented in the US by Jorj Osterberg, and offered as a commercially available service in thelate 1980s (Osterberg, 1989)"

Jan 1, 2004

By Peter Faust, Peter Hubbard, Kenichi Soga

The European Federation of Foundation Contractors (EFFC) and The Deep Foundations Institute (DFI) have set up a task group to compile a Guide for Working Platforms. The first edition of this Guide has been published in January 2020. The aim of the Guide is to provide reliable methods for design, testing and verification of working platforms for construction equipment, especially in the deep foundation industry where track loads can be excessive due to the nature of its operations. The Guide has identified areas where knowledge is limited. Actual track pressure and its distribution along the length of the tracks is still not well researched. Current recommendation provided in EN 16228-1 are believed to be overly simplified and may lead to conservative requirements for working platform thickness. This paper presents results of a series of field tests where the actual track pressure of a large drilling rig during operation was measured in real time together with the deformation of the working platform. Embedded, distributed fiber optic sensing (DFOS) at different depths throughout the platform allowed for a three-dimensional evaluation of the platform deformation throughout the entire operation. Results will help to develop more reliable recommendations for future safety requirements of working platforms for deep foundation equipment.

May 1, 2022

By Stephan A. Jefferis, Adrian H. Bath

"This paper draws together some themes on the durability of barrier systems, and particularly cementitious systems. For contaminated land and water retaining structures, durability can be poorly addressed at all stages of a project, from specification, to barrier material selection, barrier design including toe-in and through to performance assessment in operation. Permeability (hydraulic conductivity) is a dynamic property which will vary over time as reaction processes propagate through a barrier. However, laboratory testing, when undertaken, tends to be focused on short term tests with aggressive chemicals so that the effects of longer-term processes such as carbonation and leaching by permeating water are missed. For water retaining structures, carbonation and leaching actually may be the most significant processes affecting barrier performance as the groundwater adjacent to many water bodies can be otherwise rather benign (as regards bentonite and cementitious systems). These and other reaction processes have been modelled in the arena of nuclear waste repositories and procedures are well recognised. However, such procedures have yet to be widely adopted for the assessment of other barrier systems.INTRODUCTIONOver the last few decades there has been an enormous amount of laboratory research on the durability of barrier materials or more specifically papers reporting the results of permeability tests. Unfortunately there is a much smaller literature on scaling test results to barrier dimensions in the field or to required design lives. Although in the geotechnical industry durability research has been largely laboratory based, in the nuclear industry where relevant timescales are multi-millennia rather than decades, research has been heavily underpinned by geochemical modelling. A significant purpose of this paper is to examine the tools that may be used to analyse the results of tests on barrier materials used in geotechnical engineering, for example, for water retaining structures and contaminated land and draw the attention of the construction industry to the potential of the modelling procedures developed for nuclear repository assessments. Modelling can help to identify underlying processes and so augment information from laboratory testing focused on changes of physical properties such as permeability and strength."

Jan 1, 2016

By Thai Nguyen Ph. D

Dynamic Load Test (DLT) on driven piles has been performed routinely all over the world. In several recent projects, even 100% testing has become a norm where every single pile is dynamically load tested. In these cases, most piles are of uniform sections, making the field analysis (CASE method) straight forward. The CASE method, which has been used for the last 50 years, however, is only applicable to uniform piles to monitor pile driving stresses as well as pile capacities. Signal matching analysis can handle different configurations. However, the analysis used to require user inputs (i.e., non-automatic). Manual signal matching analysis, which can solve non-uniform solutions, traditionally takes hour(s) to complete for one blow. As such, the real-time pile driving stresses and resistances had traditionally been relying upon the CASE method, using typical range of CASE damping (JC). Until 2021, due to the lack of a rigorous instant signal matching analysis for non-uniform piles, no tool was available to help engineers evaluate non-uniform piles in real-time. An inexperienced field engineer may overlook this shortcoming when evaluating peak driving stresses. Furthermore, ultimate bearing resistances for non-uniform piles may require further evaluation to account for the non-uniformity of piles if relying on the CASE method. This paper highlights recent advances in instant Signal Matching Analysis on non-uniform piles, allowing field engineers to monitor stresses and resistances of non-uniform piles during driving.

Oct 1, 2022

By Ambarish Ghosh, Subhaprasad Chakraborty

"Construction of basement floors has become necessary to meet the requirement of parking in office and residential complexes and in hospitals for radiotherapy treatment. Important projects coming up in Kolkata are mostly in closer proximity of residential buildings, office buildings and historical monuments. Sheet piling is mostly used as temporary shoring system during construction. Deep excavation in urban environment creates great problem related to construction induced vibration due to driving of sheet piles for basement, pile driving etc. which raises the chances of damage of adjacent buildings and nearby structures. Vibratory sheet-pile driving is the most common method of sheet pile installation. The knowledge of induced vibration due to this phenomenon is still very deficient. This paper presents the analysis of measured vibration data collected from different sites of Kolkata with varying soil profile. Typical two case studies of sheet pile and pile driving has been presented and the vibration values are analysed. The responses of the vibration are reported in terms of peak particle velocities (PPV). To evaluate the effects of vibration due to pile driving two aspects have been considered: the effect of the energy entering the ground from the pile and the effect of the soil condition.INTRODUCTIONIn urban areas infrastructure development projects are mainly located adjacent to existing structures like residential buildings, offices and historical structures. The construction work of such project influences the surrounding environment as well as human perception (Wiss 1981). During the construction of basement for residential complexes and hospitals sheet piling is mostly used as temporary shoring system or as to support the earth mass. The vibration induced due to driving of piles and sheet piles have been presented herein. Deep excavation projects close to existing structures increase the concern of environmental impact. For this reason the vibration assessment and prediction has become a subject of great interest. It is important to develop a site specific model for predicting the ground vibration resulting from pile and sheet pile driving at the construction sites. The developed model gives the efficacy to guide the engineer to select the construction methodology ensuring the safety of the surrounding structure. The model developed here is site specific and the parameters that has been used are dependent on the soil condition and the energy source."

Jan 1, 2015

By Massimo Poggio, Gabriele Balconi, Andrea M. R. Pettinaroli, Mario Ruggiero, Riccardo Castellanza

Grouting technologies are ground treatment techniques used for modifying the behaviour of a mass of soil or rock by injecting a mixture. The sleeved port pipes (also called Tube A Manchette) are highly diffused for grouting treatment of coarse soils and fissured rocks. This paper describes a combination of jet grouting and rock grouting with MPSP (multiple packer sleeve pipe) technique that has been used to realize waterproof curtains under fluvial structures for a cascade hydro-power plant. This is composed by five mini hydro-power plants, placed along the Iskar River, in Bulgaria, and composed by a penstock followed by the power house, a spillway, and an earth dam containing the reservoir. The geology of the site is characterized by an upper alluvial deposit lying over the bedrock. In each site, similar treatments were carried out: an impervious curtain along the plant section, obtained by executing jet-grouting columns in the surficial alluvial layers and grouting the underlying fractured rock by means of port pipes. The temporary embankment, built during the works for protecting each site from the possible river floods, has been waterproofed and stabilized by reinforced jet-grouting columns. The grouting processes have been controlled and monitored by a computerized system. INTRODUCTION The Iskar river cascade hydropower plant is situated northern of Sofia, Bulgaria, and it is composed by nine plants. Actually five of them have been built and produce energy. Each plant is composed by a penstock followed by the turbine building, a spillway, and an earth dam that contains the reservoir. The Iskar rivers runs in a narrow valley characterized by diorite or diabase rocks, with an upper deposit of alluvial soil, composed mainly by gravel and sand. Each plant requires an impervious curtain under the structures and in correspondence of the earth dam: this has been obtained by means of a jet grouting treatment of the alluvial coarse soil, and a grouting treatment with cement mixtures of the underlying rock using the MPSP technology. During the construction of the structures, the site has been shielded from the river water by a temporary earth embankment that has been statically improved and waterproofed by jet grouting columns reinforced with steel tubes; this allowed to work without interruption even in case of flood of the Iskar river.

Jan 1, 2019

By Quanchen Sun, Mohammed Z. E. B. Elsahife, Anthony Fisher, Chris Barker, Jennifer Schooling

A review of the literature shows that pile integrity is a significant concern in pile construction. Recently, a new integrity test, thermal integrity profiling (TIP,) has been put into use in foundation construction. It measures temperature changes and thermal profiles of concrete during curing. Heat generation and dissipation of early-age concrete is determined by the concrete mix, the ground conditions and the shape of concrete structure. The current data interpretation practice is primary based on experience. Anomaly detection through direct analysis of temperature profiles is currently indicative or suggestive and temperature signatures are usually similar, and numerous causes are not easily isolated. The core of the TIP testing technique, i.e. collecting detailed temperature measurements along the pile during the hydration process, is promising but a new interpretation approach is required. In this paper, a new interpretation approach has been developed in which TIP constitutes the first step. An investigative staged process is then followed to establish and assess the anomalies in the problematic regions along the pile employing the combined use of detailed finite element (FE) simulations, the actual temperature data from TIP and genetic evolution algorithms. In each stage, more details could be revealed about the anomalies being investigated including, ultimately, location, size and shape; this staged process enables practitioners to follow a riskbased approach and decide whether or not to pursue subsequent stages depending on the results they get at the end of each stage. This new approach, depending on the stages required for the analysis, will potentially avail practicing engineers of crucial test results about the quality of the pile immediately following pile construction, hence enabling repair and remedial work straight away at a lower cost.

May 1, 2022

By Glen Mann, H. G. Vestberg, Robert D. Holtz

"Underpinning of residential and commercial structures is often accomplished using a number of driven-in-place small diameter steel pipe piles. These piles, at least in the Seattle area, are typically described as pin-piles and are driven with an air compressor operated jack hammer to a refusal criterion developed from an empirical basis. Over the past twenty years or so, the materials have improved in quality and strength, and the driving equipment has improved in efficiency and capability. These improvements have resulted in damage to the pin-piles during driving as well as to the driving equipment. The primary objectives of this load testing study were to develop a relationship between the driving penetration resistance of 2-inch diameter pin-piles and the ultimate bearing capacity when piles were driven at different penetration rates and, based on the load test results, to develop an opinion regarding an increase in the allowable axial load capacity [ultimate load capacity divided by a factor of safety] of a 2-inch diameter pin-pile over the currently used permissible load capacity of 4 kips in the Seattle area. Also, if feasible, a reduction in the present driving penetration rate was to be recommended to help reduce the rate and magnitude of pile and equipment damage whilst maintaining the allowable load capacity. The recorded ultimate bearing capacities were also compared with the Tagnent-line and the Davisson analytical methods in an effort to determine if either of these provided a reasonable determination of the pile load capacity.IntroductionThis paper describes the results of a series of load tests performed on small diameter, 2-inch, driven-in-place steel pin (pipe) piles and based on these results, provides the support for a modification to the presently used allowable axial pin-pile capacities.The intent of the load testing program was to determine how much influence the penetration resistance might have on the individual piles' ability to support the allowable axial load without undergoing any significant vertical deformation. For the purposes of this paper the ""allowable load capacity"" is considered to be the ultimate pile load capacity divided by a minimum factor of safety, typically considered to be 2.0 in this area. A pin (pipe) pile comprises an open or closed ended, schedule 80 steel tube which is driven-in-place, usually with an air compressor operated 90 pound pneumatic jack hammer. These jack hammers typically operate at a rate of about 1,200 blows per minute, (Haggard, Holtz and Mann, 2001 )."

Jan 1, 2005

By Aniruddha Sengupta, Rana Chattaraj, G. R. Reddy, Raj Banerjee

"Earthquake induced liquefaction in saturated granular soils is an important phenomenon which causes severe damage to life and property. In the present study, dynamically induced liquefaction of saturated Kasai River sand is studied in 1-g shake table to assess its liquefaction potential. In the shake table, the soil was subjected to sinusoidal motions of amplitude 0.35g at a frequency of 2Hz. A numerical model using FLAC 2D (Itasca 2005) was performed to simulate the shaking table tests. Reasonably good agreement between the experimental and the numerical results has been observed. Moreover, wavelet analysis has been conducted to identify the occurrence of liquefaction in sand and to correlate the observations found from the experiments. The nonlinear curves used to represent shear strain dependency of stiffness of the Kasai River sand was obtained from cyclic tri axial tests.INTRODUCTIONThe term Liquefaction is used in conjunction with a variety of phenomena that involve soil deformations due to cyclic disturbance in saturated soil under undrained conditions. The generation of excess pore water pressure is the hallmark of all liquefaction related phenomena and the reduction in the volume or the tendency of cohesionless soil to densify during undrained loading condition as prevails during an earthquake is also well known. Use of shaking table tests to understand liquefaction of soils has been demonstrated by several researchers (Ye et al. 2013; Ha et al. 2011). Mohajeri and Towhata 2003 and Towhata et al. 2006 carried out 1-g shaking table tests on soil models prepared in laminar box to study the rate dependent behavior of liquefied soils. Ueng et al. 2010 used a biaxial laminar shear box mounted on shaking table to study the settlements in saturated clean deposits of sand and related the volumetric strain in liquefied sand to the relative density for various shaking durations and earthquake magnitudes. Maheshwari et al. 2012 reported increase in liquefaction resistance of reinforced sand through shaking table tests and concluded that the type and amount of reinforcement in the soil layer has influence on its liquefaction potential.The objective of the present study is to compare the behavior of dry and saturated Kasai River sand when subjected to seismic shaking. The Kasai River separates two growing cities, Medinipur and Kharagpur in the state of West Bengal in India. A number of road and railway bridges exist over the river connecting the two cities. The area being in Seismic Zone III, that is, a zone with moderate probability of earthquake, it is important to characterize the behavior of the Kasai River sand during a possible earthquake event especially when a number of bridges are existing over it. Small scale laboratory model tests and numerical analyses using a commercial finite difference algorithm called FLAC2D (Itasca 2005) have been utilized to study the difference in behavior of dry and liquefied Kasai River sand during dynamic loading conditions."

Jan 1, 2015

By Racquel Nottingham, Marc Mastrantuono

Micropiles often provide a favourable solution for many deep foundation problems especially when significant site constraints such as confined construction sites or vibration limitations have been identified. Often the durability of buried steel elements are heavily scrutinized in order to effectively determine the rates of corrosion and methods to reduce this while still maintaining the structural integrity of the engineered solution. Practices such as sacrificial corrosion loss and the introduction of plastic sheaths have become the go-to methods of corrosion protection. Since the introduction of the micropile, other solutions have been developed, namely protection with an adequate grout encapsulation. This paper will explore corrosion protection of micropiles and the guidelines provided in the published codes and norms. Since few codes define the exact way to verify the durability of these micropiled structures, the existing data is presented and the analysis of grout encapsulation as an effective corrosion protection method is evaluated.

Oct 1, 2022

By Frederic A. Verheyde

The CPT pile design method of the ‘Laboratoire des Ponts et Chaussées’ (LPC) uses the cone resistance (qc) for the design of axially loaded piles. It was originally proposed in 1982 and was revised in 1993 and 2012. It has been widely used in France for several decades and is included in the current French pile design code. The objective of this paper is to summarise the two first versions (1982 and 1993) of the method and to detail the most recent one as described in the current French pile design code (AFNOR 2012).

Nov 1, 2022

By Norm Kirk, Robert Bittner

"The addition of a new powerhouse at the existing Tulloch Hydroelectric site on the Stanislaus River in the western foothills of the Sierras Nevada Mountains of central California required a deep excavation in rock on the downstream face of the dam. A cofferdam (water exclusion device) was necessary to isolate the powerhouse construction site excavation from the existing Goodwin Reservoir and the turbulent discharge from the existing powerhouse. The cofferdam was positioned on a steeply sloping fractured rock surface exceeding 50 degrees.This paper describes the challenges encountered during design and construction of the cofferdam and describes the unique design features used to address these challenges including:•,The use of flat-sheet-piles to form cellular walls on the steeply sloping rock surface.•,The use of 5-ft deep tremie concrete plugs in the bottom of the sheet pocket cells to create the bottom seal of the cellular cofferdam walls against the sloping rock surface.•,The use of vertical post-tensioned rock anchors to provide shear resistance at the contact point between the base of the cellular-wall and the sloping rocksurface.INTRODUCTIONModification or expansion of existing hydroelectric power plants often require downstream cofferdams or water exclusion devices to temporarily separate new construction from turbulent downstream discharge of the existing dam. Most dams are positioned on solid rock in the narrowest and therefore the steepest section of the river. This combination of steeply slopingrock and the need for an exclusion barrier creates a challenge for the design engineer trying to maintain a safe dewatered construction site. Typical cofferdam solutions for hydroelectric dams usually use large granular filled circular sheet pile cells that perform as gravity structures. However, this type of structures is not well suited to steeply-sloping highly irregular rock surfaces in a confined area."

Jan 1, 2017

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Numerical lateral load analysis based on the beam on Winkler foundation (BNWF) model (i.e., the p-y method) is a simple, and widely used tool to predict lateral responses of drilled shafts from field load tests. The lack of a site-specific p-y model for cemented soil layers such as caliche is one of the major limitations of simulating lateral load tests conducted in Las Vegas Valley. In this study, some of the existing p-y models for rock materials, such as Florida Limestone and Vuggy Limestone have been evaluated to simulate the lateral resistance of caliche. This has been done in the context of four lateral load tests in caliche-dominant sites from the recently constructed Raiders Stadium project in Las Vegas (NV). The uncertainty in characterizing the material properties of caliche has been addressed. The p-y analyses were performed using NVShaft, a MATLAB-based, comprehensive load analysis program. The applicability of the considered p-y models for caliche material was evaluated by quantifying the normalized error margins between measured and predicted lateral responses from the simulations of the mentioned load tests. Correlations between such errors and the depth and thickness of caliche in soil layers affecting numerical predictions were established, for both up to and beyond design load levels.

Oct 1, 2022