Search Documents

By George S. Rice

The prevention of coal-mine explosions has been one of the chief purposes of the Bureau of Mines. In facti the first Federal appropriation relating to mining methods, in 1908, authorized the investigation of the causes of mine explosions and the possible methods of preventing them. When that investigation started the mining industry had not determined the real causes of a succession of terrible coal-mine explosions in various countries, culminating in the great disasters at CoulTièl'es, France, and Monongah, W. Va. Coal dust as an agent of widespread explosions had been under suspicion, and watering to allay the dust was recommended by some mining engineers but the watering of coal-mine dust was adopted in comparatively few mines of the United States and Great Britain, and had not been introduced widely in any country except Germany. Rock dusting, another method of preventing explosions of coal dust, was early tested with success by the Bureau of Mines in its fist gallery at Pittsburgh and, beginnig in 1911, at the experimental mine, Bruceton, Pa. Several of the fist publications i of the bureau suggested that rock dust be used in gaseous or dusty bituminous mines, and in 1915 Technical Paper 842 strongly recommended it. Since that time additional tests in the experimental mine have fully confied this :ft judgment.

Jan 1, 1924

The use of coal as a fuel causes air, pollution in; a number of different forms, and in nearly all stages of its, handling, preparation, storage, use and-disposal of its residue. First let us consider the handling of coal. As shipped, particularly to large utilities, it is run-of-mine bituminous made up of large chunks as well as pulverized particles. Because it 'is in an open car or barge, it is subject to the action o winds and the small particles may be blown around adding to the-particulate load in the atmosphere. Mien un¬loaded from the barge or car, there is again an opportunity for the wind to blow the fine particles around. All of us I am sure have seen a barge at the dock of a utility plant being unloaded by a clamshell bucket. This, after grabbing its load from the barge, lifts it some 60 or 70 feet and, then drops it on a conveyor, which carries the coal to a storage area.

Jan 1, 1964

By A. Ploszajski

This item examines the history and uses of tungsten, from discovery to superalloys via the lightbulb and electron beam instruments.

Apr 1, 2015

By W. L. Swager

Tramp (undesirable) elements introduced into iron and steel castings via purchased ferrous scrap are evaluated as to their likely degree of future threat to the quality of castings. Conclusions are based on analysis of literature and on nonmail surveys of foundries, scrap processors, trade and technical associations, and others. The existing tramp-element problem is expected to be persistent, but amenable to improved control by foundries and their suppliers. Four recommendations for action are given.

Jan 1, 1981

By Herbert Clark Hoover, Lou Henry Hoover

As stated in the preface, the nomenclature to be adopted for weights and measures has presented great difficulty. Agricola uses, throughout, the Roman and the Romanized Greek scales, but in many cases he uses these terms merely as lingual equivalents for the .German quantities of his day. Moreover the classic language sometimes failed him, whereupon he coined new Latin terms adapted from the Roman scale, and thus added further confusion. We can, perhaps, make the matter dearer by an illustration of a case in weights. The Roman centumpondium, composed of zoo librae, the old German ceniner of 100 pfundt, and the English hundredweight of 1112 pounds can be called lingual equivalents. The first weighs about 494,600 Troy grains, the second 721,900, and the third 784,000. While the divisions of the centumpondium and the centner are the same, the Libra is divided into 12 unciae and the pfundt into 16 unizen, and in most places a summation of the units given proves that the author had in mind the Roman ratios. However, on p. 509 he makes the direct statement that the centumpondium weighs 146 librae, which would be about the correct weight if the centumpondium referred to was a ceniner. If we take an example such as " each centumpondium of lead contains one uncia of silver", and reduce it according to purely lingual equivalents, we should find that it runs 24.3 Troy ounces per short ton, on the basis of Roman values, and 18.25 ounces per short ton, on the basis of old German. If we were to translate these into English lingual equivalents of one ounce per hundredweight, then the value would be 17.9 ounces per short ton. [ ]

Jan 1, 1950

By J. W. Thompson

Be if enacted by the Senate and House of Representatives of the United States of America in Congress assembled, That deposits of coal, phosphate, sodium, oil, oil shale, or gas, and lands containing such deposits owned by the United States, including those in national forests, but excluding lands acquired under the Act known as the Appalachian Forest Act, approved March 1, 1911 (Thirty-sixth Statutes, page 9G1), and those in national parks, and in lands Withdrawn or reserved for military or naval uses or purposes, except as heroinafter provided, shall be subject to disposition in the form and manner provided by this Act to citizens of the United States, or to any association of such persons, or to any corporation organized under the laws of the United States, or of ;iny State or Territory thereof, and in the case of coal, oil, oil shale, or gas, to municipalities: Provided, That the United States reserves the right to extract helium from all gas produced from lands permitted, leased, or other- wise granted under the provisions of this Act, under such rules and regulations as shall be prescribed by the Secretary of the Interior: Provided further, That in the extraction of helium from gas produced from such lands, it shall be so extracted as to cause no substantial delay in the delivery of gas produced from the well to the purchaser thereof: And provided further, That citizens of another country, the laws, customs, or regulations of which, deny similar or like privileges to citizens or corporations of this country, shall not by stock ownership, stock holding, or stock control, own any interest in any lease acquired under the provisions of this Act.

Jan 1, 1921

By W. T. Abel

The difficulties associated with wet-processing fine size coal led the Bureau of Mines to investigate a dry process for removing pyrite from coal pulverized to powerplant fineness. The dry process that was investigated consists of two cleaning steps: First, centrifugal separation is used to remove a fine, pyrite-depleted portion as a product; second, the remaining coarser, pyrite-enriched portion is taken to electrostatic separation in which pyrite is concentrated and rejected. Ball milling and Hardgrove milling were used to pulverize the coal. Three coals from the Pittsburgh seam were treated by the dry-removal process. Over 55 pct of the pyrite, which amounted to 70 pct of the available pyrite, was removed in a reject of 10 to 20 pct from one of the coals. Similar treatment of the other two coals removed about 35 to 50 pct of the pyritic sulfur, which amounted to about 70 pct of the available pyritie, sulfur from these coals. Both centrifugal and electrostatic separations were more efficient when pyrite particles were as large as possible. Separation efficiency was improved by confining the particle size of the feed to a relatively narrow range and by avoiding excessive amounts (more than 10 pct) of dust in the electrostatic range. The removal efficiency was increased with the use of stage grinding.

Jan 1, 1973

Jan 1, 1994

By John A. Mathews

RESEARCH in the steel industry, as in other lines of manufacturing, has for its principal purpose the increasing of profits. That is what manufacturing companies are for, and all departments of the organization must be so coordinated as to lead to profitable operation. To divide a payroll into productive and non-productive labor is misleading. Productive labor, in fact, is necessary labor, and non- productive labor is the labor we can get along without. One might as well say that the steering wheel is not a part of an automobile as to say that the directing minds of an industry are non-productive. Legitimate manufacturing profits in a steel company or any other company are the reward that the public pays for service rendered or risk taken. The desire for profits is the impelling motive that leads investors .to take risks and build up industries that give employment to others. Every department of a company, be it executive, manufacturing, financial, sales, or research, must contribute to the one end which brings success-profits.

Jan 1, 1921

By Schumacher, Earle E.

THE solidus line above the solid solution field in the lead-antimony system was originally determined by Dean and his associates1 from heating curves. They did not regard this line as having been accurately fixed and in their more recent publications2 the curves drawn do not follow closely the original data. The precise location of the solidus line is of importance in the extrusion of lead-antimony cable sheath, as the temperature of the metal in this process must be less than the lowest temperature at which any part of the alloy in the lead-press charge becomes liquid. It is very desirable, however, to operate at as high a temperature as possible, as the rate of extrusion for a given pressure is approximately doubled for an increase of 10" C. in temperature. The precise location of this line is also important in the investigation of ternary systems of lead, antimony and a third metal. For these reasons, and because of the differences reported in the literature, data were secured on the lead-antimony solidus line by the classical quenching-test procedure.

Jan 1, 1927

By S. H. Lorain

This paper is one of a series being published by the Bureau of Mines describing the mines and mills and subjects related to mining in western mineral areas. Although mining districts in the Tobacco Root Mountains are numerous there is a strong similarity in the character of the ore deposits and in the climatic and economic conditions affecting mining throughout the region. Individual mines are small, but the production of lode mines

Jan 1, 1937

By Soule&apos, John H.

Although known since 1902, the Capitan iron deposits have not been tined, mainly because of the low grade of the ore. Only a small amount of exploratory work has been done since the discovery. C. H. Johnson, district engineer of the Bureau of Mines in New Mexico in 1942-4, visited the property; as a result, preliminary sampling of the property was done in 1943.2/ Owing to the results of this preliminary work, an extensive development program by wagon drilling was planned and executed early in 1944. Equipment available at that time was limited in the depths that could be reached; and as geologic studies indicated the possibility that other limestone beds below the surface might have been replaced by iron minerals, a supplementary development program by churn drilling to reach greater depths was prosecuted in late 1947 and early 1948, with the author as project engineer.

Jan 1, 1949

By Eric S. Weiss

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research to evaluate explosion blast effects on typical U.S. mine ventilation stoppings in the NIOSH Pittsburgh Research Laboratory?s (PRL) Lake Lynn Experimental Mine (LLEM). An innovative Australian-designed brattice stop-ping was also evaluated. After mine explosion accidents, MSHA conducts investigations to determine the cause(s) as a means to prevent future occurrences. As part of these postexplosion investigations, the condition of underground stoppings, including the debris from damaged stoppings, is documented as evidence of the approximate strength and the direction of the explosion forces. The LLEM data showed that a typical dry-stacked and coated solid-concrete-block stopping survived a total explosion pressure of ~6.7 psi (~46 kPa) and was destroyed at a total explosion pressure of ~7.6 psi (~52 kPa). In comparison, a typical dry-stacked and coated hollow-core concrete block stopping survived a total explosion pressure of ~3.4?4.3 psi (~23?30 kPa) and was destroyed at a total explosion pressure of ~3.6?5.2 psi (~25?36 kPa), depending on the length of the pressure pulse and the value of the pressure-time integral. A typical steel panel stopping design survived a total explosion pressure of 0.8 psi (5.5 kPa) and failed at a total explosion pressure of 1.3 psi (9 kPa). The LLEM data also showed that an obstacle blocking the path of a pressure wave resulted in a higher reflected pressure at the obstacle. An 8-in (20-cm) thick wet-laid solid-concrete-block stopping coated on one side survived a total explosion pressure of ~26 psi (~180 kPa); this stopping was not tested to failure. A 6-in (15-cm) thick wet-laid solid-concrete-block stopping coated on one side survived a total explosion pressure of ~14 psi (~97 kPa) and was destroyed at a total explosion pressure of ~25 psi (~172 kPa). An innovative Australian woven cloth stopping survived an explosion pressure of 4.0 psi (27 kPa) and was destroyed at an explosion pressure of ~6.1 psi (~42 kPa). These results will help investigators determine the approximate explosion forces that destroy or damage stoppings during actual coal mine explosions.

Jan 1, 2008

By Oliver C. Ralston

The minerals that enter welding-rod coatings and fluxes are the main subject of this report. Few mineral producers know just what minerals and what grades and quantities of minerals are required by the welding trade, and it is for their information that this report has been prepared. The various methods of welding are discussed extensively enough to inform this type of audience. Specialists in welding probably will find little on welding that is of value to them, but they may learn something more about the minerals or mineral products that they use. The authors did not find it easy to prepare this publication, and any needed corrections will be welcomed. Regarding welding, research, Jenks4/ 1 points out that while the process of welding in simple in operation, the phenomena attending its use are extremely complicated, and the efficient and safe use of welding requires an understanding thereof. Although the fluxes and the coatings used have solved many problems, many other problems require the joint effort of the whole industry; therefore, it is hoped that this report will be found of practical value.

Jan 1, 1940

By Wm Petruk

"The tungsten-bismuth-molybdenum deposit in southwestern New Brunswick occurs in greisenized and silicified tuffite * and feldspar porphyry in and adjacent to volcanic necks. The ore minerals occur as veins and veinlets and as disseminated grains in gangue. These minerals can be grouped into three assemblages. Assemblage 1 consists of oxides and phosphates of W, Ti, Fe, Nb, Sn, Ta and rare-earth elements, with the main minerals being deposited in the sequence wolframite, rutile, cassiterite. Assemblage 2 consists of arsenopyrite, molybdenite and bismuth, and assemblage 3 of sulphides with minor cassiterite and arsenopyrite. Sphalerite is the main sulphide mineral, but it contains minute inclusions of copper-tin- and indium-bearing minerals. Textural relations suggest that most of the elements can be recovered from this ore by conventional mineral beneficiation and extraction methods, but a variety of techniques must be employed. It is expected that the wolframite and molybdenite can be recovered satisfactorily, but poor recoveries are expected for bismuth and cassiterite. A sphalerite concentrate can be readily obtained by flotation, but it would contain a wide variety of elements. It is suggested that leaching be used to recover the bismuth and the elements in the sphalerite concentrate."

Jan 1, 1973

By J. Swanepoel, J. H. van Laar, J. C. Vosloo, W. A. Pelser

Deep-level underground mining costs in South Africa are continuously rising due to the increased depth at which gold is being mined, resulting in a rise in virgin rock temperature and an increase in cooling requirements. Therefore, mines must evaluate various ventilation and cooling optimisation projects required to be implemented throughout their life of mine (LOM). This study develops a method to identify and prioritise large capital expenditure (CAPEX) underground environmental improvement projects, to improve thermal comfort underground. The solution presents a ‘multi-criteria decision-making’ (MCDM) process, incorporating the ‘analytic hierarchy process’ (AHP) and the ‘technique for order performance by similarity to ideal solution’ (TOPSIS) into the method to provide for scientific decision-making. These projects are evaluated based on four criteria, namely project risk, the impact on the underground thermal comfort, cost, and implementation time. This study’s solution uses ventilation simulations to determine the impact of the projects on the underground environment. The identification and evaluation of an environmental improvement project to best suit the current economic climate, while improving underground conditions and decreasing the safety risk is an essential aspect of the solution developed in this study. The method was implemented on a mechanised deep-level underground mine and showed that surface refrigeration is the most suitable alternative, which was implemented at the case study mine as validation of the developed solution. The study proves that the MCDM method is an adequate solution to incorporate subjective criteria into the decision-making process, resulting in a scientific and structured approach to making significant and complex decisions.

Feb 17, 2023

By Lever R. R

The paper discusses assay methods generally used when prospecting for gold, and also the applicability of various chemical methods, it describes a new paper chromatographic technique.for making fairly rapid semi-quantitative assays for very fine gold. Testing of the method in field work shows that this simple method could have applications in geologic work, in prospecting and in certain routine mine sampling work. It is not yet a method that can be used to detect anomalies in traces of gold dispersed around an orebody, as is general practice in geochemical prospecting.INTRODUCTIONAccording to the English economist Harrod (1958), "the acute shortage of gold in the world-because currency value has not been adjusted in line with the fall in the goods value of the various currencies-has been a familiar fact for some time now". Harrod calculates that a rise in the price of gold to double its present value is necessary to rectify this condition, and that, if this rise were to take place, increase in production and reduction in private hoarding might well bring annual accretion to world stocks from the presentaverage of about $464 million to a figure close to the $2,000 million that would probably eiiminate these shortages.Any increase in the price of gold is bound to lead to a great increase in prospecting at working mines, in abandoned areas and possibly in untouched country. Prospecting, techniques for base metal orebodies have improved greatly in the last thirty years; but methods available to detect gold occurring without accessory metals have not received the same attention. With this in mind a paper chromatographic method of assaying for gold has been developed by Lever (1958). In the field this semi-quantitative method has proved...

Jan 1, 1959

By Iván E, Alex Araya Jofre, Jean Guiroux Toro, Eduardo Valdés Guerra

Currently, it is important for companies to have controlled mining operations and adhere to production schedules. To achieve this, one of the key factors is maintaining high reliability in the P&T process, primarily the opening of ore stope, which could be delayed due to any unplanned or uncontrolled problem. These ore stope opening processes, whose main activity is generating free face, are a very important pillar for future mine planning. The possibility of ensuring their opening brings a series of downstream benefits: safety, economics, productivity, and compliance and adherence to plans. The process under discussion consists of developing free faces in a single blasting event. This will help us leverage greater reliability for overall production operation plans, reduce construction times, and open up opportunities for downstream improvements in the production process, considering technical factors in P&T designs. This study presents a developed methodology and shows the results of its implementation in ten (18) single-event free face blasts. The analysis includes cavity geometry, geology, rock qualities, drilling deviations, and the blasting strategy implemented for each event. The methodology used considered material fluffing processes, the actual drilling trajectory, the initiation sequence, QA/QC during explosive loading, monitoring instrumentation (vibrations), and VOD recording, among others. As a result, out of a total of 18 free-face events blasts in a single event, 16 were successful and two achieved 90% efficiency, reducing the stope's production start-up time by 50% compared to current operations. By implementing free face blasting in a single event, there are savings in operating costs, increased productivity of the mining equipment, and improved adherence to production plans. For applications with greater heights of free faces, where blasting cannot be carried out in a single event, we should consider performing them in two stages using wireless detonators already available on the market for mining operations.

Jan 26, 2026

By Stephen A. Orr

Underground mining is a dynamic art and science with a diverse set of design, production, and economic criteria that must be considered before selecting an optimal method to extract the ore. While all methods can be technically classified as either self-supported, supported, or caving, the multitude of subsystems and existing variations bear witness to the fact that each orebody is unique and, as such, justifies an individual approach to optimize mineral extraction. In this sense, underground mining is an art. The ability to evaluate the unique characteristics of each ore body and utilize sound engineering principles to design the optimal system constitutes effective method selection. The task by no means ends at this juncture, however. Subsequent implementation requires an ability for modification. Very rarely are all the facts available to make a concrete decision prior to development of the resource. As a result, the risk of a wrong decision can never be eliminated. This requires a significant degree of flexibility with each method. Each unit of exploration, development, or exploitation work contributed to a deposit enhances knowledge of the ore body. The best mining methods are those that correctly account for the known parameters but provide an allowance for change at minimal cost and adapt to unanticipated conditions.

Jan 1, 2008

By J. A. Kost

A survey of 80 coal producers was conducted to determine the extent and scope of respirable dust control research for underground coal mines and the current methods employed to control respirable dust. Results of the survey showed that proper face ventilation and an adequate water spray system are sufficient to comply with mandatory standards in room and pillar mining. Difficulties still exist with longwall equipment, auger miners and buring machines. In these cases, known dust control techniques are not sufficient to obtain compliance. Present state-of-the-art face ventilation and water systems were discussed in addition to the sampling program.

Jan 1, 1980