Search Documents

By E. H. Bentzen

The purpose of this paper is to explain the production of sand for glass manufacturing and the reasoning behind the sand specifications set by the glass industry. In order to discuss the production of glass sand, there is a need to understand what glass is and how it is made. Therefore this paper discusses glass, as well as sand beneficiation.

Jan 1, 1977

By R. Brändle, R. Luis-Fonseca, R. Cornejo, G. Fischer, G. Von Rickenbach, J. Jarufe

Rock damage around underground excavations has been an important hazard in mines and tunnels. Rock dilation generates buckling that needs to be contained before it causes damage to equipment or safety concerns to mine workers. In seismically active mines, rockburst occurrence has been widely recognized as one of the most important hazards in deep mines and tunnels. While there is a wide range of cases where rockburst hazard can be mitigated through dedicated excavation sequences, reentry procedures or exclusion zones, there are still many situations where large unexpected rockbursting may occur, relying only on rock support as the last mitigation measure to prevent production and safety losses. Considering the previous situations, surface support as mesh, plays a major role containing the failed/ejected rock and providing a safe working environment to the underground operations. While there have been considerable achievements in improving mesh resistance, with more than 26Kj/m2 of energy dissipation capacity, there is still a lack of research in the overlapping mechanism and load transfer between contiguous mesh elements. This paper presents the state of the art in static and dynamic analysis of welded and rolled mesh overlaps, based on experimentation carried on by Geobrugg in their Research Center, leaving clearly established that the difference in meshes is not only in levels of energy absorption, but also concluding that in the case of high resistance rolled meshes overlapping is not necessary and the transmission of stresses can be fully guaranteed by using suitable connecting elements. All these characteristics, supported by operational advantages as light weight and mechanized mesh installation, provides a considerable improvement in safety and productivity, improving the economic value of the project

Apr 26, 2022

By R. J. Matetic, J. Noll, C. Zhou, J. DuCarme, M. Reyes, J. Srednicki

"In April 2016, the U.S. Mine Safety and Health Administration (MSHA) began requiring the use of continuous personal dust monitors to monitor and measure respirable mine dust exposures to underground coal miners. Mines are currently using the PDM3700 personal dust monitor to comply with this regulation. After the PDM3700’s implementation, mine operators discovered that it interfered with proximity detection systems, thus exposing miners to potential striking and pinning hazards from continuous mining machines. Besides the PDM3700, other electronic devices were also previously reported to interfere with proximity detection systems. MSHA sought the aid of the U.S. National Institute for Occupational Safety and Health (NIOSH) and mining industry stakeholders to determine how the PDM3700 and some other electronic devices and proximity detection systems interact with each other. Accordingly, NIOSH investigated existing standards, developed test protocols, designed experiments and conducted laboratory evaluations. Some interferences were observed to be caused by electromagnetic interference from some electronic devices, including the PDM3700. Results showed that there was no significant interference when the PDM3700, as well as other electronic devices, and the miner-wearable component of the proximity detection system were separated by distances of 15 cm (6 in.) or greater. In the present study, it was found that the PDM3700 and the personal alarm device needed to be at least 15 cm (6 in.) apart in order for them to be used simultaneously and reduce potential interference. IntroductionUnderground coal miners are exposed on a daily basis to a variety of hazards, such as coal dust exposures, high noise levels, roof and rib falls, potential for fires and explosions, and operating and working with heavy machinery. One of the hazardous jobs is that of operating or working near a continuous mining machine. According to U.S. Mine Safety and Health Administration (MSHA) statistics, 44 miners had been fatally struck or pinned by a continuous mining machine since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are required on all operating continuous mining machines in underground coal mines, with the exception of full-face continuous mining machines, by 2018 (MSHA, 2015a)."

Jan 5, 2018

By J. H. Kempton

Refinement of environmental procedures can produce significant cost savings at most mines. Grouting permeable aquifers reduces water pumping and disposal costs. Stable groundwater quality supports reduced groundwater monitoring; and for contaminated groundwater, in-situ or natural restoration should be evaluated. Waste-rock characterization can be minimized using fewer (but more representative) samples, inexpensive surrogate analyses (e.g., NAG instead of humidity cells), and appropriate tests (e.g., avoid meteoric tests on sulfide). Selective waste-rock handling should be compared to random emplacement, which is often cheaper and more stable. Finally, incorporating schedule uncertainty in modeling allows the flexibility to revise mine plans within permits.

Jan 1, 2000

By T. Petrov

This study was performed to analyze the behavior of the blowing curtain face ventilation system modified with a specially designed regulator, called Wing Regulator. The purpose of the regulator is to extend the airflow penetration depth toward the face and allow effective face ventilation at curtain setback up to 13.7m (45ft) from the face. A small scale model of the Wing Regulator was successfully tested in the Mine Ventilation Laboratory at the University of Kentucky. Then a prototype of the proposed regulator was tested in full-scale in mine environment. Series of three dimensional simulations were performed to support this research using validated CFD code. This paper presents results of the performed studies and discuses the advantages of using the Wing Regulator. Presented information relates to the US Provisional Patent Application No 61/818,112.

Feb 23, 2014

By Dick T. Atkinson

Due to improvements in the safety of other aspects of mining (primarily in roof control), haulage related accidents, particularly rail haulage accidents, are about to become the most common category of hazards causing death and injuries to underground coal miners. The major causes of these accidents are collisions between vehicles, men caught between rib and trip or between cars, derailments, and runaway cars. Such hazards can be greatly reduced if the motorman has the capability to selectively couple and uncouple cars from the cab of the locomotive, to transmit braking intelligence to the coupled cars, to determine if the trip is intact, and if brakes are automatically applied in any uncoupled car. These capabilities can be provided through an improved coupler system, designed and built by Foster-Miller Associates under a Bureau of Mines contract. Early in the program, a survey of rail haulage patents and literature was conducted. Manufacturers of couplers, mine cars and braking systems were contacted and information relevant to the remote control mine haulage application was collected. From this information evolved a working specification and a design concept. The key elements of the specification, shown in Table I, are the result of a detailed tradeoff study and considerable thought given to the specific problems encountered in the mining environment. A brief explanation of each element is as follows: Automatic Coupling - The couplers operate similarly with most already in underground use - they latch together when a trip is backed into a car intended for coupling. Remote Uncoupling - From the locomotive, the motorman can decide how many cars are to be uncoupled, operate the appropriate controls, and the desired coupler is opened.

Jan 1, 1977

By A. L. Anderson, J. T. Rybock

Lime, soda ash and similar precipitants have been the industry standard for treatment of acid rock drainage (ARD) because of their proven ability and low per-gallon operational cost. However, these methods carry serious environmental drawbacks and high life-cycle costs. KEECO’s Silica Micro Encapsulation (SME) technology has all the positive characteristics of conventional ARD-treatment systems but none of the drawbacks. SME achieves highly effective treatment in a single step, provides options for ARD prevention and recovery of metals, requires lower capital expenditures, generates smaller volumes of higher-density sludge, consistently passes leach tests, and eliminates long-term liabilities associated with potential metal remobilization and hazardous waste landfilling.

Jan 1, 2000

By Willard A. Murray

Investigations of underground coal gasification (UCG) have been actively pursued by the U.S. Department of Energy since the early 1970s; the Lawrence Livermore National Laboratory (LLNL) conducted its first field experiment in 1976. In conjunction with field and laboratory studies of the process of recovering energy in the form of combustible gases from the burning of coal deposits in situ, an extensive environmental program has been conducted at LLNL under the auspices of both the U.S Department of Energy and the U.S. Environmental Protection Agency. This program has focused on groundwater contamination and ground surface subsidence caused by UCG. The material presented in this paper is a summary of results from the environmental studies of UCG activities conducted by LLNL as described by Mead, et al. (1981) and supplemented by the author's experience with this program in 1980 and 1981. The following sections describe specific groundwater contamination and surf ace subsidence problems encountered during field experiments in northeastern Wyoming, and will discuss implications of preliminary findings from geohydrological investigations of a site in southwestern Washington. Finally, possible environmental control technologies that are most likely to be effective in mitigating environmental impacts are discussed.

Jan 1, 1982

By Donald R. Williamson

Statistical studies at Cyprus Pima Mine indicate that samples from 22 blastholes are necessary for determining average copper grades, within a desired range of precision, for mine-model blocks by arithmetic averaging. The average number of holes in such blocks is 14. Many considerations show that more holes will not be drilled for sampling. A way to determine block grades more reliably than by" arithmetic averaging was sought. Thus far arithmetic averaging has proven to be the best procedure for the particular operation characteristics despite the small number of samples. It naturally follows that expenditure of great effort in sampling blasthole cuttings is unwise.

Jan 1, 1977

By E. J. Mayhew

Bentonite and newly discovered deposits of sepiolite, saponite, and hectorite are now being processed and marketed from the Amargosa Valley of Nevada. All of these deposits are large. The bentonite has been known for decades and is the whitest known. The only other sepiolite deposit is in Spain. The only other commercial hectorite deposit is at Hector, California. No other saponite deposit is known. All the components except bentonite are hydrous magnesium silicates. The bentonite is mixed layer Na-Ca. All the materials have characteristics unique to their locale and type, such as high yield point for drilling muds and liquid suspending agents. The sepiolite has geothermal stability. Figure 1.

Jan 1, 1979

By D. Bahrami, W. K. Asante, G. L. Danko

It is prudent to interpret atmospheric monitoring signals in real time for checking the safe limits of the air conditions in underground mines. In gassy mines, real-time evaluation increases the safety of operations. In all mines, continuous monitoring and evaluation contributes to maintaining air conditions within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase in hazardous contaminant concentrations can be predicted by signal pattern recognition, root cause analysis of rapid changes toward deterioration, and forward prediction in time using algorithms and numerical models. The paper describes an early warning system for analyzing monitored signal patterns continuously in real time as well as forward predicting the various environmental and working conditions to recognize dangerous trends that may affect safety and health in underground mines. A dynamic, numerical ventilation model with heat and gas contaminant simulation components is used for the analysis of atmospheric data. Methods and test results are discussed with numerical examples for signal propagation prediction. Several mine examples are studied using controlled, synthetic data for malfunction simulations to evaluate time delays between the detection time of suspicious signal trends and the time of dangerous threshold crossing marking an accident scenario. Delay time is found in the order of 20 min in the examples, signifying the useful time period for preventive intervention between EWS warning and the likely breakout of a following accident.

By S. S. Klima, H. Jiang, T. W. Beck, Y. Zheng

Researchers at the National Institute for Occupational Safety and Health (NIOSH) performed a series of lab tests to evaluate the respirable dust removal capacity of an industrial air-cleaning fan. Limestone and coal dust were tested separately in NIOSH’s full-scale drill table simulator at the Pittsburgh Mining Research Division (PMRD). Gravimetric samplers with Dorr-Oliver Cyclones and 37-mm filters were used at two upstream and four downstream locations inside and outside of the drill shroud chamber. There were six tests performed for both the limestone and coal dust experiments. In the limestone tests, an average respirable dust concentration of 98.86 mg/m3 was achieved upstream of the air-cleaning fan. The filter results show that the averaged respirable limestone dust reductions were 7.84%, 8.81%, 10.94%, and 18.02% at the four sampling locations downstream of the fan. In the coal tests, upstream samplers achieved an average of 129.03 mg/m3 of respirable coal dust. The averaged dust reductions were 9.54%, 9.83%, 18.54%, and 19.21% at the four downstream sampling points. The results indicate limited cost benefits of using this technology because of the relatively low dust reductions determined from this laboratory study.

Feb 1, 2023

By Harvey Parker

This is part two of an article on the prominent role that the United States and its industry leaders have played on the International Tunnelling and Underground Space Association (ITA), which represents the underground construction and underground space industries worldwide. The U.S. is officially represented in ITA by UCA of SME. (Part one is in T&UC, June 2007, pp 39-42) Tunnel advances in 1960s and 1970s The 1960s and 1970s were active and productive times for the U.S. tunneling industry. During that time, federal programs, sponsored by the Federal Railroad Administration (FRA), the Office of High Speed Ground Transportation (OHSGT) and the Advanced Research Projects Administration (ARPA), stimulated tunnel research and development. Also, the American Society of Civil Engineers (ASCE) and SME collaborated to create the Underground Construction Research Council (UCRC) and the Rapid Excavation and Tunneling Conference (RETC) series.

Jan 1, 2007

By Yuchen Wu, Jing Mei, GUOZHONG LIU, KE GAO, Songjie Tian, Jianwei Cheng, Yu Wang, Yuhang Wu, Hui Wang

The stability and integrity of protective coal pillars between the longwall working face and development roadways are greatly affected by the mining activities such as the development face advancing or retreat mining. Due to underground strata pressure, the coal pillar cracks could be further developed and then the air leakage passages (mainly cracks) could be produced greatly. The air circulation caused by the atmospheric pressure difference between the two sides of the coal pillar may also provide suitable conditions for the possible spontaneous combustion of the residual coal in the mine gob. In this paper, a typical the protective coal pillar in a Chinese coal mine is studied. The deformation and stress of coal pillars during the mining process of longwall working face are simulated by using FLAC3D. The displacement and strain of coal pillars are analyzed. Two indexes, the linear fracture rate (LFR) and area fracture rate (AFR), are introduced to characterize the development of internal cracks’ development within coal pillars. By using field measurement, the air leakage intensity distribution due to coal pillar cracks is obtained; the equation of air leakage resistance of coal pillar under the influence of mining is derived. Then, the possible location of large air leakage of coal pillar is determined, which can be used as guidelines to study the possibilities of coal spontaneous combustions happening in pillar or mine gob. The research results help to control such potential hazards in advance.

Jun 16, 2022

By F. Ikumapayi

In order to predict and minimize detrimental production problems due to the recycling of process water in sulfide ore processing, the influence of major species, calcium and sulfate in process water on sphalerite flotation was investigated through Hallimond tube flotation, zeta potential, diffuse reflectance Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) measurements using sphalerite mineral sample. Assessment of process water species in flotation was done using deionized water, process water and simulated water containing calcium and sulfate ions in experiments. Hallimond flotation shows increased sphalerite float-ability in process water compared to deionized water, but no significant effect on the presence of calcium and sulfate ions in deionized water using isobutyl xanthate as a collector. The presence of calcium ions reduced the sphalerite?s negative zeta potential, while at higher concentrations, a charge reversal occurred, at about pH 11. FTIR and XPS studies revealed the presence of surface-oxidized sulfoxy and carbonate species on sphalerite at pH 11.5 in deionized water, process water and water containing calcium and sulfate ions. These surface species do not influence xanthate adsorption.

By W. A. Mathews

We report on the progress of an automated mineralogical deportment of fluorine (F) in two portions of the Grasberg District for the development of metallurgical amelioration protocols for Cu sulfide concentrates. Fluorine detection limits in automated SEM technologies range from 1% (TIMA) to about 9% (QEMSCAN), however substitution in hydrophobic minerals or those reporting to concentrate is typically much lower (

Mar 2, 2022

By Thomas B. Borak, Keith J. Schiager, Janet A. Johnson

OBJECTIVES OF RADIATION MONITORING Monitoring is a tool used in the practice of radiation protection. The primary reasons for monitoring are to reduce radiation exposures to levels that are as low as reasonably achievable and to assure that no individual receives a dose exceeding the maximum individual dose limit. The documentation of radiation doses for legal, medical, or epidemiological reasons is a subordinate function of any monitoring program. The investment in radiation monitoring programs should be guided by four criteria: (1) the detection and avoidance of unnecessary exposures, (2) the magnitude of potential health risks, (3) the determination of combined doses and risks with adequate confidence, and (4) the verification of compliance with established limits. FIRST CRITERION: DOSE REDUCTION - DETECT AND CORRECT UNNECESSARY EXPOSURES The system of dose limitation advocated by the International Commission on Radiological Protection (ICRP, 1977), and subscribed to in a broad sense by various regulatory agencies, is comprised of three essential ingredients: (1) [justification] of any practice that produces radiation doses by some commensurate net benefit, (2) [optimization] of radiation control measures by reducing doses to levels that are as low as reasonably achievable, and (3) [limitation] of individual doses to preclude inequities and [moldistribution] of risks. All too often, only the third criterion - the limitation of individual doses to prescribed regulatory limits - is explicitly addressed in everyday radiation protection programs. The emphasis of most exposure control and monitoring efforts appears to be directed toward limiting and documenting individual doses that might approach the legal limit. The first two criteria, i.e. justification and optimization, should contribute to a rationale for allocating monitoring efforts. When applied to individuals, these criteria mean the detection and elimination of unnecessary exposures. This should be a high priority of any monitoring program. Measurements should be directed toward detecting inoperative or ineffective control measures, whether or not there is a risk of exceeding the individual dose limits. The ICRP recommends a procedure that can be used effectively to reduce unnecessary exposures. A n investigation level should be established at an exposure rate substantially lower than the regulatory limit, e.g. 30% of the limit (ICRP 26, 1977, p.33). Measurements obtained during routine monitoring that exceed the investigation level are evaluated with respect to cause and potential reduction. To be effective, the evaluation results should be formally recorded and conveyed both to management and to the workers involved. Although the investigation level recommended by the ICRP is based on a fixed exposure rate or derived air concentration, an equally effective evaluation program may be based on the investigation of a percentage of all measurements. For example, one might investigate the highest 5% or a random selection of all measurements. In any case, the objective is to detect and correct situations that are producing unnecessary exposures. SECOND CRITERION: MONITOR IN PROPORTION TO THE MAGNITUDE OF RISK The ICRP criteria apply generally to all radiation exposures. However, a second priority for monitoring programs should be established on the basis of the nature of the exposures and the magnitude of the health risks involved. Current practices in radiation protection are based on dose limits to specific organs and assessment of individual exposure pathways, with little consideration of the combined doses from various pathways. Although the intent of the ICRP recommendations was to limit the total dose to each critical organ, combined doses from external and internal sources are rarely determined. The recent recommendations of the ICRP (Publ. 26, 1977) are based on the limitation of total health risk from occupational radiation exposures. Implementation of this concept would necessarily require the measurement, calculation and summation of doses and concomitant risks to all organs of the body from all exposure pathways. The U.S. Environmental Protection Agency has taken the first step toward translating the ICRP recommendations into regulations. The proposed recommendations for Federal Radiation Protection Guidance for Occupational Exposures (USEPA, 1981) include provisions for summing the risk-weighted organ doses to determine compliance with an effective whole-body dose equivalent limit. Whether or not the proposed guidance is modified before final adoption, it seems clear that some version of dose summation and combined risk limitation will be included in future regulations. With this

Jan 1, 1981

By George J. Hartman

The Fort Cady in situ borate-mining project involves recovering boron from a deposit more than 400 m (1,300 ft) below the surface. The resource recovery method is a new in situ mining technology that uses weak acid solution injected directly into the ore body. As the acid contacts the calcium-based ore (primarily natural colemanite), the contained borate values are digested as boric acid. This boric acid solution is then pumped to the surface by submersible pumps. A series of chemical reactions and precipitations are performed that result in the production of calcium borate. The borate values are then recovered as a finely divided solid white powder. The refined product is sold under the trade name Cadycal 100. The Fort Cady in situ borate-mining project is located about halfway between Los Angeles, CA and Las Vegas, NV in the Mohave Desert.

Jan 1, 1996

By D. Gu

Shaft drilling is one of the most useful methods of driving shafts. This paper describes the application and development of the technique in coal mine construction in China.

Jan 1, 1993

By E. A. Schmidt

In 1962, while investigating the tungsten potential in the Thompson Creek area for Union Carbide Corp., Henry T. Eyrich obtained anomalous concentrations of molybdenum (up to 19 ppm Mo) from stream sediment samples collected along Pat Hughes Creek, a tributary to Thompson Creek. Follow-up investigations by Eyrich during the same year disclosed the presence of a hydrothermally altered and molybdenite-bearing granitic exposure in the headwaters of Pat Hughes Creek about 2.4 km (1.5 miles) upstream from the sample point. The altered outcrop measured about 549 by 305 m (1800 by 1000 ft), contained abundant northwest-trending quartz veins locally with molybdenite, and was overlain and surrounded by the Challis volcanic extrusive sequence of mid-Tertiary age. Eyrich's subsequent soil and rock chip geochemical sampling program over the altered outcrop area showed a general increase in the molybdenum content to the northwest toward the postmineral Challis volcanic cover. Over a distance of about 305 m (1000 ft), values in the altered intrusive rock increased from less than 5 ppm Mo to over 600 ppm Mo, with aconcomitant intensity of the hydrothermal alteration pattern. Based on these geochemical results and on preliminar; megascopic hydrothermal alteration studies, Eyrich correctly concluded that the altered outcrop is an erosional window and that molybdenum mineralization of sufficient grade could exist beneath the Challis volcanic cover some distance further to the northwest. His recommendation to test the area of potential molybdenum mineralization with several drill holes was, however, declined by Union Carbide in 1962. The property remained unclaimed until 1967, when Eyrich joined Cyprus Mines Corp. Acting on Eyrich's recommendation, Cyprus immediately staked 26 lode mining claims to cover not only the altered intrusive outcrop, but also the northwest trend of mineralization where it projected beneath Challis volcanic rocks. Eleven of these claims are now patented.

Jan 1, 1991