Search Documents

By Bror Nyman

Wide settlers are a way to decrease the linear velocities of advancing liquid phases. It has, however, been found unnecessary to risk a proper settler performance by building shallow settlers in order to avoid a so-called interface turbulence due to a too big difference between the linear velocities of the organic and the aqueous phase. This conclusion has been reached from tests using a large transparent settler model, where the behaviour of a clean interface between two advancing liquids has been investigated. Also in a more realistic case, making an organic in aqueous or an aqueous in organic dispersion to move between the liquid phases, no obstacle has been found to use a somewhat more deep and correspondingly ore slowly t10wing aqueous phase. Based on above findings, support can be given to a new trend to build the settlers slightly deeper than what has been typical for the so-called low-profile design. In this way, it is much easier to avoid an excessive air introduction and other severe difficulties, like those caused by crud moving from one stage to another. It is further shown, how gravity can be used to slow down and distribute a dispersion being fed into a settler of a VSF unit. Entrainment levels have been found to be reduced by a careful design of primary dispersion distributors and picket fences of the settler. Finally, it is demonstrated, how outlets from the side of the settler can be used to simplity interstage pumping and to decrease the rotation speed of any pumping device.

Jan 1, 1996

By R. M. LaDouceur, C. A. Young, W. Nicholas

"Salicyl hydroxamic acid (SHA) adsorption on two rare earth oxides, lanthanum and yttrium, was studied. Adsorption at both surfaces occurred in two stages. Initially, the monovalent anionic collector appears to adsorb significantly and instantaneously in stage one and then becomes sluggish in stage two presumably because the initial stage passivated the surface. By comparison, adsorption during the sluggish second stage with lanthanum oxide did not stop but with yttrium oxide essentially stopped. Surface monolayer formation could not be observed in either of the two cases. Both stages appear to be due to multilayer formation of a surface precipitate as proven by Raman Spectroscopy for lanthanum oxide but inferred for yttrium oxide. Unlike the use of octyl hydroxamate as stated in the literature, increasing temperatures do not increase adsorption such that flotation of rare earths with SHA may be performed at room temperature leading to improved recoveries as well as significant energy savings. INTRODUCTION Rare Earth Elements (REEs) are comprised of the 15 lanthanides along with scandium and yttrium. The REEs with lower atomic numbers are relatively more abundant and are categorized as light REEs. On the contrary, the REEs with high atomic numbers are less abundant and referred to as heavy REEs. They are not really “rare” and, in fact, some of them are quite abundant in the Earth’s crust; it’s just that they “rarely” exist in concentrated deposits but rather are found dilute and practically everywhere. REEs share very similar physico-chemical properties but, because many of these properties are unique, they have gained enormous importance in recent times making several critical and strategic pending their use. For example, REEs have found extensive application in phosphor coatings, magnetics, and automobile cracking catalysts. Early technology was not advanced enough to produce commodity level production of the REEs and can be attributed to REE-bearing ores containing many rare earth minerals (REMs), not just one. In this regard, there are numerous REMs but bastnaesite, xenotime and monazite are considered to be the most common. Bastnaesite is a fluorocarbonate whereas the other two are phosphates. The separation of the individual REE-bearing minerals from the ores is not an easy task since they also exhibit very similar properties. Consequently, when flotation is used, it is done to produce bulk REM concentrates. For REM flotation, it is well established that octyl hydroxamate is more selective than fatty acid collectors (Pradip and Fuerstenau, 1983 and 1991). Liu et al. (2006) indicated that hydroxamates are the most common collectors for REMs. Pavez et al. (1996) studied the adsorption of oleic fatty acid and octyl hydroxamate on REM surfaces. Cui et al. (2012) studied the interaction of octyl hydroxamate with various REMs surfaces using various spectroscopic techniques such as XPS, FT-IR and Raman along with electron microscopy and concluded that such techniques offer ample information to establish adsorption mechanisms. Ren et al. (1997) studied napthalenic hydroxamic acid as a unique collector for flotation of REMs from bastnaesite ore and indicated that more selective collectors were needed. From these studies, it is clear that the quest of more selective collectors is essential but understanding how they adsorb at mineral surfaces is prerequisite to improving flotation performance."

Jan 1, 2016

By D. R. Zuchelli

The purpose of wrapping ball mills with thermal/acoustic blankets is twofold: 1) to maintain the desired temperature inside the mill, and 2) to reduce the sound emanating from the mill. This field case study focuses solely on the latter, evaluating and documenting the sound level reduction attributed to the installation of the blankets on ball mills and its potential to reduce the noise dose experienced by the process attendant. One of the three ball mills had already been treated (baseline) before the evaluation started. However, treating the remaining two mills still proved to be very effective, further reducing ball mill noise in the near field by as much as 10.0 dBA and producing far field noise reductions of 3.0 dBA or greater, extending as far as 35 feet from the mills and to the floor above. The model developed from the survey data shows that a process attendant spending a substantial portion of a shift in the mill building will experience a significant reduction in overall noise dose.

Jan 1, 2010

By J. S. Lee

Alkyl hydroxamates are well known collectors for oxide copper minerals as evidenced by the large amount of published literature. Our studies on a wide variety of copper ores from around the world have shown that alkyl hydroxamates will recover most of the "floatable" oxide copper minerals from an ore. They are available commercially, and they offer many advantages over alternative technologies for oxide copper recovery. In spite of this, the full potential of hydroxamates has not been exploited in the industry. The objective of this paper is to provide relevant practical aspects and guidelines to facilitate successful application of hydroxamates in operating plants. A critical analysis of the available information and data, based on several case studies, notation testing, and microscopic analysis indicates that alkyl hydroxamates can effectively recover well-defined oxide minerals of copper, but not copper occurrences such as Cu-bearing goethite (often misidentified as cuprite) which report as Acid Soluble copper in chemical assays. Prior to any notation testing with hydroxamates, it is necessary to assess the various modes of occurrence of Acid Soluble copper using microscopic and microprobe analysis.

Jan 1, 1998

By M. J. Virnig

A flowsheet for the recovery of nickel and cobalt from laterite ores has been developed which involves acid leaching followed by hydroxide precipitation of the metal values and then releaching of the hydroxide cake with ammonia. Investigations of the chemistry of extraction of nickel by LIX® 84-1 and a developmental reagent, XI-84-IT, along with the physical properties of the organic phases are described. Based on these investigations, suggestions with regard to design of a solvent extraction plant and operating conditions are made.

Jan 1, 1999

By M. W. Harmer

Laboratory test work, pilot plant testing and plant experience with wet, fine mesh screens is discussed. High frequency, low amplitude, fine mesh, wet screens were installed on the 6th cleaner concentrate stream. These screens produce a 60% oversize recovery split of the molybdenite concentrate that is of leached equivalent quality. The undersize stream is leached with 'hot ferric chloride to remove Pb and Cu contaminates before roasting or shipment to sulfide customers. This plant modification is a good example of using existing technology in an unconventional flow sheet to yield significant cost savings.

Jan 1, 1990

By T. Gouri Charan

Indian coals, which are of Gondwana origin, contain high amounts of mineral matter, wherein the extraneous material was intimately mixed in the coal matrix during the formation stage, causing a high level of impurity in the run-of-mine (ROM) material. These coals possess difficult to very difficult washability characteristics. Beneficiation of high-ash non-coking coals of India has become the prerequisite for improving the overall economics and efficiency of power generation. The use of dry cleaning systems in India for beneficiation of non-coking coals has gaining renewed interest recently. The benefit of the dry beneficiation process is to exploit the given resources while providing a more reliable and consistent quality fuel with a low operating cost. M/S Allmineral has introduced a technique for the dry beneficiation of coal, which is being tried in India for the treatment of high-ash non-coking coals. The first commercial air jig of 50 t/hr capacity was installed and commissioned to beneficiate high-ash coals of 40 x 5 mm feed with an ash content of 40%; a clean coal product of 33% ash was produced and is being used for a sponge iron plant.

Jan 1, 2011

By Ray Brainard, Adriana Ventimiglia, Amanda Kerr

The $2 billion Horizon Lateral includes over 30 miles of trenched and tunneled pipeline with diameters up to 120 inches.Related infrastructure includes large and small pumping stations, reservoirs, and flow control facilities. This paper will discuss the strategy and processes used to determine contract packaging and contracting delivery methods for the various project elements with an emphasis on the tunnels and trenchless crossings. Prior Authority experience and the rigorous risk-based approach to develop the preferred alignments played a large role in determining the outcomes along with schedule concerns and permitting and easement acquisition.

Jun 13, 2023

By W. A. Haley

Wheel loaders were first introduced shortly after World War II as small machines designed for handling loose materials in various industrial and processing applications. It was not until the early 1950?s, however, that machine size permitted widespread loading of loose or stockpiled material into on-highway type trucks. An ever increasing number of machines continue to be used for this purpose today. In fact, it is by far the major use for wheel loaders in mining and quarrying. Many of these loaders were working at mines or quarries handling in-process or finished material and some were doing shovel clean-up. It was quite natural then, when the primary pit loading shovel was down, to attempt to maintain some production by replacing it temporarily with the wheel loaders. Most of these attempts were not very successful, however, until the really large wheel loaders, 4- to 6-yd. size were introduced in the early 1960's. Since that time these machines have proven they can be productive and economical primary pit loading tools, a job that was once the exclusive domain of the power shovel. To be competitive with the shovel however, conditions must exist or be made to exist, that will be favorable for the wheel loader.

Jan 1, 1967

The criteria used to design, operate and control flotation columns are significantly different from those used for conventional flotation machines. Therefore, a computer-aided design (CAD) package for column flotation has been developed. The simulator has been set up using guidelines developed at Virginia Tech and information published in literature during the past few years. The simulator is useful for determining the proper design and appropriate operating conditions for a column cell to fit a specific set of conditions. In addition, the simulator can be used for training in column operation and for trouble-shooting operational problems. Simulation results have been found to be in good agreement with experimental data obtained using laboratory columns.

Jan 1, 1990

Controlled blasting experiments in small development drifts were conducted at CANMET's Experimental Mine, from August 1992 to November 1993. The objective of these experiments was to develop suitable controlled blasting techniques for small development headings drilled by jackleg with 32 mm diameter holes. The experimentation also aimed to provide insight into blast damage mechanisms. Particular attention was given to the physical-mechanical properties of the rock and the rockmass structural data in order to make the results applicable to other geological environments. The drift faces were approximately 2.4 m by 2.4 m with 36 to 43 holes drilled to a depth of 2.4 m. Cartridged water gels, emulsions and semigelatin dynamite were used in the cuts and as primers, ANFO as the main explosive and decoupled 19 mm diameter semigelatin dynamite charges were used in the perimeter holes. Smooth blasting techniques and pre-splitting were tested in the underground mine. All the blasts were monitored with a multi-channel blast vibration monitor to which was attached sets of high frequency geophones and accelerometers. This first set of experiments has illustrated the efficiency of con-trolled blasting techniques to reduce blast damage and demonstrated the need for further research to improve the safe and efficient use of explosives.

Jan 1, 1995

By S. Middlemiss

The Indentation Fracture technique is being developed as a tool for use in comminution and mineral liberation analysis. Fracture toughness measurements for a number of mineralogical materials were made and comparisons were drawn between these and properties measured with the Ultrafast Load Cell drop weight apparatus. The technique has also been used as a probe to quantify differences in fracture properties at different areas in the microstructure of a material. In both a Utah limestone and a South African quartzite, material near a grain boundary fractures very differently to that in the bulk. Ongoing work is ultimately aimed at producing a comprehensive fracture model for a multi-mineral system based on its micro-fracture characteristics.

Jan 1, 1994

By John E. Litz

Coca Mines Inc. is a medium sized company exploring for and developing precious metal properties in the Western United States. They own interests in a number of properties which contain reserves of gold and silver. The Hog Heaven property presently is under development for a combination of open pit and underground mining, followed by recovery of the silver and gold by cyanidation. Property Location The properties included within the Hog Heaven Project are located in Flathead County, northwestern Montana. The property is readily accessible by road from either Polson or Kalispell, Montana, Figure 1. [ ]

Jan 1, 1984

The dissolution kinetics of gold in iodide solutions with oxygen in an autoclave was investigated. The leaching process was described by a gas-liquid-solid heterogeneous reaction. The effect of stirring speed, temperature, partial pressure of oxygen, and concentration of lixiviants on the overall leaching rate was investigated. It was found that the dissolution of gold was limited by a heterogeneous chemical reaction. The apparent activation energy was measured to be 34.7-54.3 kJ/mol under the conditions studied. Experimental findings were in good agreement with the kinetic model proposed.

Jan 1, 1996

By Stanisław Lasocki

We present an algorithm to integrate the uncertainties of mean activity rate and magnitude cumulative distribution function in the interval estimation of the primary seismic hazard parameters: the exceedance probability and the mean return period. The algorithm is applicable for both the parametric and nonparametric modeling of magnitude distribution. When the Gutenberg-Richter relation-based parametric model of magnitude distribution is used, the interval estimation of its parameters is based on the asymptotic normality of the maximum likelihood estimators. When the nonparametric kernel estimation of magnitude distribution is used, we apply the iterated bias-corrected and accelerated method for the interval estimation, based on the smoothed bootstrap and second-order bootstrap samples. Previous studies indicated that the uncertainty of mean activity rate significantly affects the interval estimates of hazard functions only when the activity rate is low and the inference period is not long (Orlecka-Sikora & Lasocki 2017). With increasing mean activity rate, the uncertainty of magnitude distribution dominates over the uncertainty of mean activity rate in the aggregated uncertainty of the hazard functions. The provided algorithm is generic and can be applied to capture the uncertainty of any multiparameter function from the uncertainties of its parameters. Here we present a further development of the algorithm developed by Orlecka-Sikora & Lasocki (2017) by presenting its implementation in the Traffic Light System approach. As an example of use, we present the confidence intervals estimation of hazard parameters for the datasets related to induced seismicity accompanying underground exploitation of copper ore in the Legnica-Głogów Copper District (LGCD) in Poland. The algorithm is under implementation to the EPISODES platform (https://tcs.ah-epos.eu/) - an IT platform that provides access to integrated research infrastructures of the Thematic Core Service of Anthropogenic Hazards (TCS AH) of EPOS (European Plate Observing System). The algorithm is also a component of the pilot developed within the EPOS SP project (No 871121), which aims to strengthen the interaction with the private sector and the added value for society. The pilot demonstrates the potential of the IS-EPOS platform software applications for the technology-related probabilistic assessment of time-dependent seismic hazard. The pilot supports a Traffic Light System approach. The current seismic hazard is compared to threshold values based on the exceedance probability for a given magnitude.

Apr 26, 2022

By M. G. Vieira

This investigation addressed the possibility of producing pellet feed at a silica content of = 1.0% using a representative sample of Samarco´s mechanical flotation tailings. This sample contained 11.0% Fe and presented an F80 = 116 µm and a d50 = 63 µm. The higher silica content was verified in the coarser fractions and the higher iron content in the fraction -37 µm. Specular hematite is the most abundant mineralogical phase in the fraction -37 µm. The technological tests used one of four methods: magnetic concentration using a wet high-intensity magnetic separator, magnetic concentration using a SLon high-gradient magnetic separator, reverse flotation or direct flotation. The methods using the magnetic concentrator SLon, reverse flotation and direct flotation did not present results meeting the target of the study: iron content in the concentrate (rougher stage) greater than 34% or iron recovery greater than 80%. Cleaner stages were not achievable with the resulting concentrates. In contrast, the most successful method consisted of using wet high-intensity magnetic separators (WHIMS) as a rougher stage and reverse flotation as a cleaner stage. Using this route, it was possible to produce a pellet feed with a silica grade of 1.0% and high specular hematite content.

Jan 1, 2010

By James N. Brentz

This paper deals briefly with the problem of efficiently selecting the most cost effective haulage truck. Problems and factors are identified that effect productivity and operating cost. Despite the sophistication of computerized vehicle simulation programs, there is a wide disparity in accuracy and methodology, particularly in dealing with the various elements of cost.

Jan 1, 1984

By Harold L. Lovell

The areas of application, the limitations imposed by water chemistry as well as the advantages and disadvantages in the use of limestone for the treatment of coal mine drainage have recently been described by the authors (1),(2), (3). The process has been demonstrated in continuous, full-scale operation to yield a treated water meeting specifications established by the Pennsylvania Sanitary Water Board and containing excess alkalinity. Their final pH levels are usually less than seven, a condition which avoids consumption of excess neutralization reagents, but which occurs with lime-based processes and results from unwanted side reactions. Operating experience has been cited by Calhoun (4) using ferric waters while others (5), (6), (7), (8), (11), have reported on related research efforts. Despite the advantages including ?the relative simplicity, and minimal costs of the process, there have been very limited industrial applications of mine drainage neutralization with limestone. Although any treatment of these waters may be considered as a temporary control measure (9), the lack of feasible, immediate alternatives, the extensive magnitude. of the waters and the high cost of treatment requires that optimum processes should be utilized and that operating experience in their use be developed as is feasible. This paper will review treatment experience with a ferrous water of moderate pollution loading .

Jan 1, 1972

By L. S. Gertsch, M. Z. Abu Bakar

The research presented here is part of a project to quantify the differences in the mechanical excavatability of rocks in dry and water-saturated conditions. A series of full-scale laboratory linear rock cutting tests were carried out with a long-bladed single disc cutter on dry and water-saturated sandstone blocks. The muck collected from the cutting tests was analyzed to establish a link with the specific energy (SE) of the operation. The coarseness index (CI), a non-dimensional parameter, was found to be a useful indicator of the relative efficiency of the cutting operation. An inverse relationship of the form SE = k CI-n was observed between SE and CI. The power n of the relationship for both dry and saturated rock was much lower than found in previous studies. The exponent n is believed to be dependent on the strength of the rock and the cutter type used. Although the average CI was lower for saturated rock than for dry rock, at the same time, saturated rock cutting was found to be less energy-intensive (in terms of SE) than dry rock cutting. Moderate correlation exists between the production rate or yield and the SE of the cutting operation for both dry and saturated rock, which can provide some useful information about the field production rate, discounting the effect of discontinuities in the rock mass.

Jan 1, 2012

By V. P. Keran

Design of the Bajo de la Alumbrera Project started in June 1995 and concentrate production commenced early in the Third Quarter of 1997. The project is situated in North-Western Argentina and is being developed by Minera Alumbrera Limited which is owned by MIM Holdings Limited of Australia (50%), North Limited of Australia (25%) and Rio Algom Limited of Canada (25%). This paper outlines the key features that were incorporated in the design from both process and plant layout perspectives. It explains the background of flowsheet and equipment selection for the plant. A feature of the flowsheet is that it incorporates gravity gold circuits in both primary and regrind circuits for recovery of gold to dore as well as in the copper concentrate product.

Jan 1, 1998